Abstract: Aircraft propulsion systems often use Y-shaped
subsonic diffusing ducts as twin air-intakes to supply the ambient air
into the engine compressor for thrust generation. Due to space
constraint, the diffusers need to be curved, which causes severe flow
non-uniformity at the engine face. The present study attempt to
control flow in a mild-curved Y-duct diffuser using trapezoidalshaped
vortex generators (VG) attached on either both the sidewalls
or top and bottom walls of the diffuser at the inflexion plane. A
commercial computational fluid dynamics (CFD) code is modified
and is used to simulate the effects of SVG in flow of a Y-duct
diffuser. A few experiments are conducted for CFD code validation,
while the rest are done computationally. The best combination of Yduct
diffuser is found with VG-2 arranged in co-rotating sequence
and attached to both the sidewalls, which ensures highest static
pressure recovery, lowest total pressure loss, minimum flow
distortion and less flow separation in Y-duct diffuser. The decrease in
VG height while attached to top and bottom walls further improves
axial flow uniformity at the diffuser outlet by a great margin as
compared to the bare duct.
Abstract: Numerical design optimization is a powerful tool that
can be used by engineers during any stage of the design process.
There are many different applications for structural optimization. A
specific application that will be discussed in the following paper is
experimental data matching. Data obtained through tests on a physical
structure will be matched with data from a numerical model of that
same structure. The data of interest will be the dynamic characteristics
of an antenna structure focusing on the mode shapes and modal
frequencies. The structure used was a scaled and simplified model of
the Karoo Array Telescope-7 (KAT-7) antenna structure.
This kind of data matching is a complex and difficult task. This
paper discusses how optimization can assist an engineer during the
process of correlating a finite element model with vibration test data.
Abstract: Signalized intersections on high-volume arterials are
often congested during peak hours, causing a decrease in through
movement efficiency on the arterial. Much of the vehicle delay
incurred at conventional intersections is caused by high left-turn
demand. Unconventional intersection designs attempt to reduce
intersection delay and travel time by rerouting left-turns away from
the main intersection and replacing it with right-turn followed by Uturn.
The proposed new type of U-turn intersection is geometrically
designed with a raised island which provides a protected U-turn
movement. In this study several scenarios based on different
distances between U-turn and main intersection, traffic volume of
major/minor approaches and percentage of left-turn volumes were
simulated by use of AIMSUN, a type of traffic microsimulation
software. Subsequently some models are proposed in order to
compute travel time of each movement. Eventually by correlating
these equations to some in-field collected data of some implemented
U-turn facilities, the reliability of the proposed models are approved.
With these models it would be possible to calculate travel time of
each movement under any kind of geometric and traffic condition. By
comparing travel time of a conventional signalized intersection with
U-turn intersection travel time, it would be possible to decide on
converting signalized intersections into this new kind of U-turn
facility or not. However comparison of travel time is not part of the
scope of this research. In this paper only travel time of this innovative
U-turn facility would be predicted. According to some before and
after study about the traffic performance of some executed U-turn
facilities, it is found that commonly, this new type of U-turn facility
produces lower travel time. Thus, evaluation of using this type of
unconventional intersection should be seriously considered.
Abstract: Crypto System Identification is one of the challenging tasks in Crypt analysis. The paper discusses the possibility of employing Neural Networks for identification of Cipher Systems from cipher texts. Cascade Correlation Neural Network and Back Propagation Network have been employed for identification of Cipher Systems. Very large collection of cipher texts were generated using a Block Cipher (Enhanced RC6) and a Stream Cipher (SEAL). Promising results were obtained in terms of accuracy using both the Neural Network models but it was observed that the Cascade Correlation Neural Network Model performed better compared to Back Propagation Network.
Abstract: In this manuscript, the LBM is applied for simulating of Mixed Convection in a Lid-Driven cavity with an open side. The cavity horizontal walls are insulated while the west Lid-driven wall is maintained at a uniform temperature higher than the ambient. Prandtl number (Pr) is fixed to 0.71 (air) while Reynolds number (Re) , Richardson number (Ri) and aspect ratio (A) of the cavity are changed in the range of 50-150 , of 0.1-10 and of 1-4 , respectively. The numerical code is validated for the standard square cavity, and then the results of an open ended cavity are presented. Result shows by increasing of aspect ratio, the average Nusselt number (Nu) on lid- driven wall decreases and with same Reynolds number (Re) by increasing of aspect ratio (A), Richardson number plays more important role in heat transfer rate.
Abstract: Dichotomization of the outcome by a single cut-off point is an important part of various medical studies. Usually the relationship between the resulted dichotomized dependent variable and explanatory variables is analyzed with linear regression, probit regression or logistic regression. However, in many real-life situations, a certain cut-off point dividing the outcome into two groups is unknown and can be specified only approximately, i.e. surrounded by some (small) uncertainty. It means that in order to have any practical meaning the regression model must be robust to this uncertainty. In this paper, we show that neither the beta in the linear regression model, nor its significance level is robust to the small variations in the dichotomization cut-off point. As an alternative robust approach to the problem of uncertain medical categories, we propose to use the linear regression model with the fuzzy membership function as a dependent variable. This fuzzy membership function denotes to what degree the value of the underlying (continuous) outcome falls below or above the dichotomization cut-off point. In the paper, we demonstrate that the linear regression model of the fuzzy dependent variable can be insensitive against the uncertainty in the cut-off point location. In the paper we present the modeling results from the real study of low hemoglobin levels in infants. We systematically test the robustness of the binomial regression model and the linear regression model with the fuzzy dependent variable by changing the boundary for the category Anemia and show that the behavior of the latter model persists over a quite wide interval.
Abstract: The purpose of this study is to determine in what
ways elementary education prospective teachers are being informed
about innovations and to explain the role of social influence in the
usage process of a technological innovation in terms of genders. The
study group consisted of 300 prospective teachers, including 234
females and 66 males. Data have been collected by a questionnaire
developed by the researchers. The result of the study showed that,
while prospective teachers are being informed about innovations
most frequently by mass media, they rarely seek to take expert
advice. In addition, analysis of results showed that the social
influence on females were significantly higher than males in usage
process of a technological innovation.
Abstract: In this paper after reviewing some previous studies, in
order to optimize the above knee prosthesis, beside the inertial
properties a new controlling parameter is informed. This controlling
parameter makes the prosthesis able to act as a multi behavior system
when the amputee is opposing to different environments. This active
prosthesis with the new controlling parameter can simplify the
control of prosthesis and reduce the rate of energy consumption in
comparison to recently presented similar prosthesis “Agonistantagonist
active knee prosthesis".
In this paper three models are generated, a passive, an active, and
an optimized active prosthesis. Second order Taylor series is the
numerical method in solution of the models equations and the
optimization procedure is genetic algorithm.
Modeling the prosthesis which comprises this new controlling
parameter (SEP) during the swing phase represents acceptable results
in comparison to natural behavior of shank. Reported results in this
paper represent 3.3 degrees as the maximum deviation of models
shank angle from the natural pattern. The natural gait pattern belongs
to walking at the speed of 81 m/min.
Abstract: Ontologies and tagging systems are two different ways to organize the knowledge present in the current Web. In this paper we propose a simple method to model folksonomies, as tagging systems, with ontologies. We show the scalability of the method using real data sets. The modeling method is composed of a generic ontology that represents any folksonomy and an algorithm to transform the information contained in folksonomies to the generic ontology. The method allows representing folksonomies at any instant of time.
Abstract: A stack with a small critical temperature gradient is
desirable for a standing wave thermoacoustic engine to obtain a low
onset temperature difference (the minimum temperature difference to
start engine-s self-oscillation). The viscous and heat relaxation loss in
the stack determines the critical temperature gradient. In this work, a
dimensionless critical temperature gradient factor is obtained based
on the linear thermoacoustic theory. It is indicated that the
impedance determines the proportion between the viscous loss, heat
relaxation losses and the power production from the heat energy. It
reveals the effects of the channel dimensions, geometrical
configuration and the local acoustic impedance on the critical
temperature gradient in stacks. The numerical analysis shows that
there exists a possible optimum combination of these parameters
which leads to the lowest critical temperature gradient. Furthermore,
several different geometries have been tested and compared
numerically.
Abstract: Our aim in this piece of work is to demonstrate the
power of the Laplace Adomian decomposition method (LADM) in
approximating the solutions of nonlinear differential equations
governing the two-dimensional viscous flow induced by a shrinking
sheet.
Abstract: Coal fly ash (CFA) generated by coal-based thermal
power plants is mainly composed of some oxides having high
crystallinity, like quartz and mullite. In this study, the effect of CFA
crystallinity toward lead adsorption capacity was investigated. To get
solid with various crystallinity, the solution of sodium hydroxide
(NaOH) of 1-7 M was used to treat CFA at various temperature and
reflux time. Furthermore, to evaluate the effect of NaOH-treated CFA
with respect to adsorption capacity, the treated CFA were examine as
adsorbent for removing lead in the solution. The result shows that
using NaOH to treat CFA causes crystallinity of quartz and mullite
decrease. At higher NaOH concentration (>3M), in addition the
damage of quartz and mullite crystallinity is followed by crystal
formation called hydroxysodalite. The lower crystalllinity, the higher
adsorption capacity.
Abstract: The aim of the article is to describe modern
contemporary systems of employees' remuneration used in
organizations, to give a general overview of these questions based on
the questionnaire survey made by the authors, as well as to assess
possible effects of economic crisis in this area. It is necessary to be
aware of the fact that firm's success in the contemporary business
environment depends not only on the technical equipment, financial
resources, availability of raw materials and information and effective
management, but one of the crucial factors of firm's success is its
human potential. The article emphasizes that the well working
remuneration system has a very important position in the
organization in the broadest sense. The paper also aims to the current
situation in the area of employees' remuneration in one of Czech
Republic regions, in the Moravian-Silesian Region.
Abstract: This paper proposes a direct power control for
doubly-fed induction machine for variable speed wind power
generation. It provides decoupled regulation of the primary side
active and reactive power and it is suitable for both electric energy
generation and drive applications. In order to control the power
flowing between the stator of the DFIG and the network, a decoupled
control of active and reactive power is synthesized using PI
controllers.The obtained simulation results show the feasibility
and the effectiveness of the suggested method
Abstract: There is wide range of scientific workflow systems
today, each one designed to resolve problems at a specific level. In
large collaborative projects, it is often necessary to recognize the
heterogeneous workflow systems already in use by various partners
and any potential collaboration between these systems requires
workflow interoperability. Publish/Subscribe Scientific Workflow
Interoperability Framework (PS-SWIF) approach was proposed to
achieve workflow interoperability among workflow systems. This
paper evaluates the PS-SWIF approach and its system to achieve
workflow interoperability using Web Services with asynchronous
notification messages represented by WS-Eventing standard. This
experiment covers different types of communication models provided
by Workflow Management Coalition (WfMC). These models are:
Chained processes, Nested synchronous sub-processes, Event
synchronous sub-processes, and Nested sub-processes
(Polling/Deferred Synchronous). Also, this experiment shows the
flexibility and simplicity of the PS-SWIF approach when applied to a
variety of workflow systems (Triana, Taverna, Kepler) in local and
remote environments.
Abstract: In this paper, we investigate the problem of the existence, uniqueness and global asymptotic stability of the equilibrium point for a class of neural networks, the neutral system has mixed time delays and parameter uncertainties. Under the assumption that the activation functions are globally Lipschitz continuous, we drive a new criterion for the robust stability of a class of neural networks with time delays by utilizing the Lyapunov stability theorems and the Homomorphic mapping theorem. Numerical examples are given to illustrate the effectiveness and the advantage of the proposed main results.
Abstract: Soft topological spaces are considered as mathematical tools for dealing with uncertainties, and a fuzzy topological space
is a special case of the soft topological space. The purpose of this paper is to study soft topological spaces. We introduce some new concepts in soft topological spaces such as soft closed mapping, soft open mappings, soft connected spaces and soft paracompact spaces. We also redefine the concept of soft points such that it is reasonable in soft topological spaces. Moreover, some basic properties of these concepts are explored.
Abstract: This study is a descriptive-normative research. It
attempted to investigate the restaurants’ firm performance in terms of
the customers and restaurant personnel’s degree of satisfaction. A
total of 12 restaurants in Bangkok, Thailand that offer Thai cuisine
were included in this study. It involved 24 stockholders/managers,
120 subordinates and 360 customers. General Managers and
restaurants’ stockholders, 10 staffs, and 30 costumers for each
restaurant were chosen for random sampling. This study found that
respondents are slightly satisfied with their work environment but are
generally satisfied with the accessibility to transportation, to malls,
convenience, safety, recreation, noise-free, and attraction; customers
find the Quality of Food in most Thai Cuisines like services, prices of
food, sales promotion, and capital and length of service satisfactory.
Therefore, both stockholder-related and personnel-related factors
which are influenced by restaurant, personnel, and customer-related
factors are partially accepted whereas; customer-related factors which
are influenced by restaurant, personnel and customer-related factors
are rejected.
Abstract: In large datasets, identifying exceptional or rare cases
with respect to a group of similar cases is considered very significant
problem. The traditional problem (Outlier Mining) is to find
exception or rare cases in a dataset irrespective of the class label of
these cases, they are considered rare events with respect to the whole
dataset. In this research, we pose the problem that is Class Outliers
Mining and a method to find out those outliers. The general
definition of this problem is “given a set of observations with class
labels, find those that arouse suspicions, taking into account the
class labels". We introduce a novel definition of Outlier that is Class
Outlier, and propose the Class Outlier Factor (COF) which measures
the degree of being a Class Outlier for a data object. Our work
includes a proposal of a new algorithm towards mining of the Class
Outliers, presenting experimental results applied on various domains
of real world datasets and finally a comparison study with other
related methods is performed.
Abstract: Fuller’s earth is a fine-grained, naturally occurring substance that has a substantial ability to adsorb impurities. In the present study Fuller’s earth has been characterized and used for the removal of Pb(II) from aqueous solution. The effect of various physicochemical parameters such as pH, adsorbent dosage and shaking time on adsorption were studied. The result of the equilibrium studies showed that the solution pH was the key factor affecting the adsorption. The optimum pH for adsorption was 5. Kinetics data for the adsorption of Pb(II) was best described by pseudo-second order model. The effective diffusion co-efficient for Pb(II) adsorption was of the order of 10-8 m2/s. The adsorption data for metal adsorption can be well described by Langmuir adsorption isotherm. The maximum uptake of metal was 103.3 mg/g of adsorbent. Mass transfer analysis was also carried out for the adsorption process. The values of mass transfer coefficients obtained from the study indicate that the velocity of the adsorbate transport from bulk to the solid phase was quite fast. The mean sorption energy calculated from Dubinin-Radushkevich isotherm indicated that the metal adsorption process was chemical in nature.