Abstract: In this research, Forming Limit Diagrams for supertension
sheet metals which are using in automobile industry have
been obtained. The exerted strains to sheet metals have been
measured with four different methods and the errors of each method
have also been represented. These methods have been compared with
together and the most efficient and economic way of extracting of the
exerted strains to sheet metals has been introduced. In this paper total
error and uncertainty of FLD extraction procedures have been
derived. Determination of the measurement uncertainty in extracting
of FLD has a great importance in design and analysis of the sheet
metal forming process.
Abstract: A total of twenty tensile biopsies were collected from
children undergoing tonsillectomy from teaching hospital ENT
department and Kurdistan private hospital in sulaimani city. All
biopsies were homogenized and cultured; the obtained bacterial
isolates were purified and identified by biochemical tests and VITEK
2 compact system. Among the twenty studied samples, only one
Pseudomonas putida with probability of 99% was isolated.
Antimicrobial susceptibility was carried out by disk diffusion
method, Pseudomonas putida showed resistance to all antibiotics
used except vancomycin. The isolate further subjected to PCR and
DNA sequence analysis of blaVIM gene using different set of primers
for different regions of VIM gene. The results were found to be PCR
positive for the blaVIM gene. To determine the sequence of blaVIM
gene, DNA sequencing performed. Sequence alignment of blaVIM
gene with previously recorded blaVIM gene in NCBI- database showed
that P. putida isolate have different blaVIM gene.
Abstract: A major challenge in biomaterials research is the
regulation of protein adsorption which is a key factor for controlling
the subsequent cell adhesion at implant surfaces. The aim of the
present study was to control the adsorption of fibronectin (FN) and
the attachment of MG-63 osteoblasts with an electronic
nanostructure. Shallow doping line lattices with a period of 260 nm
were produced for this purpose by implantation of phosphorous in
silicon wafers. Protein coverage was determined after incubating the
substrate with FN by means of an immunostaining procedure and the
measurement of the fluorescence intensity with a TECAN analyzer.
We observed an increased amount of adsorbed FN on the
nanostructure compared to control substrates. MG-63 osteoblasts
were cultivated for 24h on FN-incubated substrates and their
morphology was assessed by SEM. Preferred orientation and
elongation of the cells in direction of the doping lattice lines was
observed on FN-coated nanostructures.
Abstract: Field experiments were carried out at Owo, southwest Nigeria to evaluate the effect of different tillage practices (zero tillage with mulch (ZTM), row tillage (RT) and conventional tillage (CT), and with or without oil palm bunch ash plus poultry manure (OBA+PM) on soil chemical properties, growth and yield of ginger. The experiment was laid out in a randomized complete plot design with three replications. Soil chemical properties, growth and fresh rhizome yield reduced with frequency/intensity of tillage imposed while application of OBA+PM increased them. Among the tillage practices, the highest fresh rhizome yield (15.0t ha-1) was produced by ZTM which was significantly different from other tillage practices. Among the tillage – OBA+PM combinations, the most satisfactorily yield (20.1t ha-1) was produced by ZTM+OBA+PM while the lowest yield (15.7t ha-1) was in CT+OBA+PM.
Abstract: In this paper, we show that C*-tensor product of an arbitrary C*-algebra A, (not unital necessary) and C*-algebra B without ground state, have no approximately inner strongly continuous one-parameter group of *-automorphisms.
Abstract: The aim of the study was to determine how different
ripening processes (traditional vs. industrial) influenced the
proteolysis in traditional Serbian dry-fermented sausage Petrovská
klobása. The obtained results indicated more intensive pH decline
(0.7 units after 9 days) in industrially ripened products (I), what had a
positive impact on drying process and proteolytic changes in these
samples. Thus, moisture content in I sausages was lower at each
sampling time, amounting 24.7% at the end of production period
(90 days). Likewise, the process of proteolysis was more pronounced
in I samples, resulting in higher contents of non-protein nitrogen
(NPN) and free amino acids nitrogen (FAAN), as well as in faster
and more intensive degradation of myosin (≈220 kDa), actin (≈45
kDa) and other polypeptides during processing. Consequently, the
appearance and accumulation of several protein fragments were
registered.
Abstract: Contractor selection in Saudi Arabia is very important due to the large construction boom and the contractor role to get over construction risks. The need for investigating contractor selection is due to the following reasons; large number of defaulted or failed projects (18%), large number of disputes attributed to contractor during the project execution stage (almost twofold), the extension of the General Agreement on Tariffs and Trade (GATT) into construction industry, and finally the few number of researches. The selection strategy is not perfect and considered as the reason behind irresponsible contractors. As a response, this research was conducted to review the contractor selection strategies as an integral part of a long advanced research to develop a good selection model. Many techniques can be used to form a selection strategy; multi criteria for optimizing decision, prequalification to discover contractor-s responsibility, bidding process for competition, third party guarantee to enhance the selection, and fuzzy techniques for ambiguities and incomplete information.
Abstract: Interior brick-infill partitions are usually considered as
non-structural components, and only their weight is accounted for in
practical structural design. In this study, the brick-infill panels are
simulated by compression struts to clarify their effect on the
progressive collapse potential of an earthquake-resistant RC building.
Three-dimensional finite element models are constructed for the RC
building subjected to sudden column loss. Linear static analyses are
conducted to investigate the variation of demand-to-capacity ratio
(DCR) of beam-end moment and the axial force variation of the beams
adjacent to the removed column. Study results indicate that the
brick-infill effect depends on their location with respect to the
removed column. As they are filled in a structural bay with a shorter
span adjacent to the column-removed line, more significant reduction
of DCR may be achieved. However, under certain conditions, the
brick infill may increase the axial tension of the two-span beam
bridging the removed column.
Abstract: Conventional concentrically-braced frame (CBF)
systems have limited drift capacity before brace buckling and related
damage leads to deterioration in strength and stiffness. Self-centering
concentrically-braced frame (SC-CBF) systems have been developed
to increase drift capacity prior to initiation of damage and minimize
residual drift. SC-CBFs differ from conventional CBFs in that the
SC-CBF columns are designed to uplift from the foundation at a
specified level of lateral loading, initiating a rigid-body rotation
(rocking) of the frame. Vertically-aligned post-tensioning bars resist
uplift and provide a restoring force to return the SC-CBF columns to
the foundation (self-centering the system). This paper presents a
parametric study of different prototype buildings using SC-CBFs.
The bay widths of the SC-CBFs have been varied in these buildings
to study different geometries. Nonlinear numerical analyses of the
different SC-CBFs are presented to illustrate the effect of frame
geometry on the behavior and dynamic response of the SC-CBF
system.
Abstract: Feature selection has recently been the subject of intensive research in data mining, specially for datasets with a large number of attributes. Recent work has shown that feature selection can have a positive effect on the performance of machine learning algorithms. The success of many learning algorithms in their attempts to construct models of data, hinges on the reliable identification of a small set of highly predictive attributes. The inclusion of irrelevant, redundant and noisy attributes in the model building process phase can result in poor predictive performance and increased computation. In this paper, a novel feature search procedure that utilizes the Ant Colony Optimization (ACO) is presented. The ACO is a metaheuristic inspired by the behavior of real ants in their search for the shortest paths to food sources. It looks for optimal solutions by considering both local heuristics and previous knowledge. When applied to two different classification problems, the proposed algorithm achieved very promising results.
Abstract: Metal matrix composites (MMC) are generating
extensive interest in diverse fields like defense, aerospace, electronics
and automotive industries. In this present investigation, material
removal rate (MRR) modeling has been carried out using an
axisymmetric model of Al-SiC composite during electrical discharge
machining (EDM). A FEA model of single spark EDM was
developed to calculate the temperature distribution.Further, single
spark model was extended to simulate the second discharge. For
multi-discharge machining material removal was calculated by
calculating the number of pulses. Validation of model has been done
by comparing the experimental results obtained under the same
process parameters with the analytical results. A good agreement was
found between the experimental results and the theoretical value.
Abstract: Aluminum/Copper clad sheet has been fabricated using
asymmetric extrusion method, which caused severe shear deformation
between Al and Cu plate to easily bond to each other. Interfacial
microstructure and mechanical properties of Al/Cu clad were studied
by scanning electron microscope equipped with energy dispersive
X-ray detector, micro-hardness, and tension tests. The asymmetric
extrusion bonding was very effective to provide a good interface for
atoms diffusion during subsequent annealing. The strength of bonding
was higher with the increasing extrusion ratio.
Abstract: As the information age matures, major social
infrastructures such as communication, finance, military and energy,
have become ever more dependent on information communication
systems. And since these infrastructures are connected to the Internet,
electronic intrusions such as hacking and viruses have become a new
security threat. Especially, disturbance or neutralization of a major
social infrastructure can result in extensive material damage and social
disorder. To address this issue, many nations around the world are
researching and developing various techniques and information
security policies as a government-wide effort to protect their
infrastructures from newly emerging threats. This paper proposes an
evaluation method for information security levels of CIIP (Critical
Information Infrastructure Protection), which can enhance the security
level of critical information infrastructure by checking the current
security status and establish security measures accordingly to protect
infrastructures effectively.
Abstract: It is by reason of the unified measure of varieties of resources and the unified processing of the disposal of varieties of resources, that these closely related three of new basic models called the resources assembled node and the disposition integrated node as well as the intelligent organizing node are put forth in this paper; the three closely related quantities of integrative analytical mechanics including the disposal intensity and disposal- weighted intensity as well as the charge of resource charge are set; and then the resources assembled space and the disposition integrated space as well as the intelligent organizing space are put forth. The system of fundamental equations and model of complete factor synergetics is preliminarily approached for the general situation in this paper, to form the analytical base of complete factor synergetics. By the essential variables constituting this system of equations we should set twenty variables respectively with relation to the essential dynamical effect, external synergetic action and internal synergetic action of the system.
Abstract: The aim of this paper is to introduce a parametric
distribution model in fatigue life reliability analysis dealing with
variation in material properties. Service loads in terms of responsetime
history signal of Belgian pave were replicated on a multi-axial
spindle coupled road simulator and stress-life method was used to
estimate the fatigue life of automotive stub axle. A PSN curve was
obtained by monotonic tension test and two-parameter Weibull
distribution function was used to acquire the mean life of the
component. A Pearson system was developed to evaluate the fatigue
life reliability by considering stress range intercept and slope of the
PSN curve as random variables. Considering normal distribution of
fatigue strength, it is found that the fatigue life of the stub axle to
have the highest reliability between 10000 – 15000 cycles. Taking
into account the variation of material properties associated with the
size effect, machining and manufacturing conditions, the method
described in this study can be effectively applied in determination of
probability of failure of mass-produced parts.
Abstract: Currently, many types of no-reversible compressed
sound source, represented by MP3 (MPEG Audio Layer-3) are
popular in the world and they are widely used to make the music file
size smaller. The sound data created in this way has less information as
compared to pre-compressed data. The objective of this study is by
analyzing EEG to determine if people can recognize such difference as
differences in sound. A measurement system that can measure and
analyze EEG when a subject listens to music were experimentally
developed. And ten subjects were studied with this system. In this
experiment, a WAVE formatted music data and a MP3 compressed
music data that is made from the WAVE formatted data were
prepared. Each subject was made to hear these music sources at the
same volume. From the results of this experiment, clear differences
were confirmed between two wound sources.
Abstract: The paper presents the results of theoretical and
numerical modeling of propagation of shock waves in bubbly liquids
related to nonlinear effects (realistic equation of state, chemical
reactions, two-dimensional effects). On the basis on the Rankine-
Hugoniot equations the problem of determination of parameters of
passing and reflected shock waves in gas-liquid medium for
isothermal, adiabatic and shock compression of the gas component is
solved by using the wide-range equation of state of water in the
analitic form. The phenomenon of shock wave intensification is
investigated in the channel of variable cross section for the
propagation of a shock wave in the liquid filled with bubbles
containing chemically active gases. The results of modeling of the
wave impulse impact on the solid wall covered with bubble layer are
presented.
Abstract: This study endeavors to evaluate the effects of farmers’ training program on the adoption of improved farming practices, the output of rice farming, and the income as well as the profit from rice farming by employing an ex-post non-experimental data in Sierra Leone. It was established that participating in farmers’ training program increased the possibility of adoption of the improved farming activities that were implemented in the study area. Through the training program also, the proceeds from rice production was also established to have increased considerably. These results were in line with the assumption that one of the main constraints on the growth in agricultural output particularly rice cultivation in most African states is the lack of efficient extension programs.
Abstract: Minimum Quantity Lubrication (MQL) technique
obtained a significant attention in machining processes to reduce
environmental loads caused by usage of conventional cutting fluids.
Recently nanofluids are finding an extensive application in the field
of mechanical engineering because of their superior lubrication and
heat dissipation characteristics. This paper investigates the use of a
nanofluid under MQL mode to improve grinding characteristics of
Ti-6Al-4V alloy. Taguchi-s experimental design technique has been
used in the present investigation and a second order model has been
established to predict grinding forces and surface roughness.
Different concentrations of water based Al2O3 nanofluids were
applied in the grinding operation through MQL setup developed in
house and the results have been compared with those of conventional
coolant and pure water. Experimental results showed that grinding
forces reduced significantly when nano cutting fluid was used even at
low concentration of the nano particles and surface finish has been
found to improve with higher concentration of the nano particles.
Abstract: In the recent past, there has been an increasing interest
in applying evolutionary methods to Knowledge Discovery in
Databases (KDD) and a number of successful applications of Genetic
Algorithms (GA) and Genetic Programming (GP) to KDD have been
demonstrated. The most predominant representation of the
discovered knowledge is the standard Production Rules (PRs) in the
form If P Then D. The PRs, however, are unable to handle
exceptions and do not exhibit variable precision. The Censored
Production Rules (CPRs), an extension of PRs, were proposed by
Michalski & Winston that exhibit variable precision and supports an
efficient mechanism for handling exceptions. A CPR is an
augmented production rule of the form:
If P Then D Unless C, where C (Censor) is an exception to the rule.
Such rules are employed in situations, in which the conditional
statement 'If P Then D' holds frequently and the assertion C holds
rarely. By using a rule of this type we are free to ignore the exception
conditions, when the resources needed to establish its presence are
tight or there is simply no information available as to whether it
holds or not. Thus, the 'If P Then D' part of the CPR expresses
important information, while the Unless C part acts only as a switch
and changes the polarity of D to ~D.
This paper presents a classification algorithm based on evolutionary
approach that discovers comprehensible rules with exceptions in the
form of CPRs.
The proposed approach has flexible chromosome encoding, where
each chromosome corresponds to a CPR. Appropriate genetic
operators are suggested and a fitness function is proposed that
incorporates the basic constraints on CPRs. Experimental results are
presented to demonstrate the performance of the proposed algorithm.