Abstract: The experimental study of position control of a light
weight and small size robotic finger during non-contact motion is
presented in this paper. The finger possesses fingertip pinching and
self adaptive grasping capabilities, and is made of a seven bar linkage
mechanism with a slider in the middle phalanx. The control system is
tested under the Proportional Integral Derivative (PID) control
algorithm and Recursive Least Square (RLS) based Feedback Error
Learning (FEL) control scheme to overcome the uncertainties present
in the plant. The experiments conducted in Matlab Simulink and xPC
Target environments show that the overall control strategy is efficient
in controlling the finger movement.
Abstract: To establish optical communication between any two
satellites, the transmitter satellite must track the beacon of the
receiver satellite and point the information optical beam in its
direction. Optical tracking and pointing systems for free space suffer
during tracking from high-amplitude vibration because of
background radiation from interstellar objects such as the Sun, Moon,
Earth, and stars in the tracking field of view or the mechanical
impact from satellite internal and external sources. The vibrations of
beam pointing increase the bit error rate and jam communication
between the two satellites. One way to overcome this problem is the
use of very small transmitter beam divergence angles of too narrow
divergence angle is that the transmitter beam may sometimes miss
the receiver satellite, due to pointing vibrations. In this paper we
propose the use of genetic algorithm to optimize the BER as function
of transmitter optics aperture.
Abstract: The aim of this paper is to present a comparative
study on two different methods for the evaluation of the equilibrium
point of a ship, core issue for designing an On Board Stability System
(OBSS) module that, starting from geometry information of a ship
hull, described by a discrete model in a standard format, and the
distribution of all weights onboard calculates the ship floating
conditions (in draught, heel and trim).
Abstract: Nowadays use of a new structural bracing system
called 'Knee Bracing System' have taken the specialists attention too
much. On the other hand nonlinear static analysis procedures in
estimate structures performance in earthquake time have taken
attention too much. One of these procedure is modal pushover
analysis (MPA) procedure. The accuracy of MPA procedure for
simple steel moment resisting frame has been verified and considered
in Chintanapakdee and Chopra-s article in 2003. Since the accuracy
of MPA procedure has not verified for semi-rigid steel frames with
knee bracing, we are going to get through with this matter in this
study. For this purpose, the selected structures are four frames with
different heights, 5 to 20 stories, will be designed according to AISC
criteria. Then MPA procedure is used for the same frames with
different rigidity percentiles of connections. The results of seismic
responses are compared with dynamic nonlinear response history
analysis as exact procedure and accuracy of MPA procedure is
evaluated. It seems that MPA procedure accuracy will come down by
reduction of the rigidity percentiles of semi-rigid connections.
Abstract: Recently, some convergent results of the generalized AOR iterative (GAOR) method for solving linear systems with strictly diagonally dominant matrices are presented in [Darvishi, M.T., Hessari, P.: On convergence of the generalized AOR method for linear systems with diagonally dominant cofficient matrices. Appl. Math. Comput. 176, 128-133 (2006)] and [Tian, G.X., Huang, T.Z., Cui, S.Y.: Convergence of generalized AOR iterative method for linear systems with strictly diagonally dominant cofficient matrices. J. Comp. Appl. Math. 213, 240-247 (2008)]. In this paper, we give the convergence of the GAOR method for linear systems with strictly doubly diagonally dominant matrix, which improves these corresponding results.
Abstract: This paper addresses one of the most important issues
have been considered in hybrid MTS/MTO production environments. To cope with the problem, a mathematical programming model is
applied from a tactical point of view. The model is converted to a fuzzy goal programming model, because a degree of uncertainty is involved in hybrid MTS/MTO context. Finally, application of the
proposed model in an industrial center is reported and the results prove the validity of the model.
Abstract: This report shows the performance of composite
biodegradable film from chitosan, starch and sawdust fiber. The main
objectives of this research are to fabricate and characterize composite
biodegradable film in terms of morphology and physical properties.
The film was prepared by casting method. Sawdust fiber was used as
reinforcing agent and starch as polymer matrix in the casting
solution. The morphology of the film was characterized using atomic
force microscope (AFM). The result showed that the film has
smooth structure. Chemical composition of the film was investigated
using Fourier transform infrared (FTIR) where the result revealed
present of starch in the film. The thermal properties were
characterized using thermal gravimetric analyzer (TGA) and
differential scanning calorimetric (DSC) where the results showed
that the film has small difference in melting and degradation
temperature.
Abstract: Adaptive Genetic Algorithms extend the Standard Gas
to use dynamic procedures to apply evolutionary operators such as
crossover, mutation and selection. In this paper, we try to propose a
new adaptive genetic algorithm, which is based on the statistical
information of the population as a guideline to tune its crossover,
selection and mutation operators. This algorithms is called Statistical
Genetic Algorithm and is compared with traditional GA in some
benchmark problems.
Abstract: In this research work, investigations are carried out on
Continuous Wave (CW) Nd:YAG laser welding system after
preliminary experimentation to understand the influencing parameters
associated with laser welding of AISI 304. The experimental
procedure involves a series of laser welding trials on AISI 304
stainless steel sheets with various combinations of process parameters
like beam power, beam incident angle and beam incident angle. An
industrial 2 kW CW Nd:YAG laser system, available at Welding
Research Institute (WRI), BHEL Tiruchirappalli, is used for
conducting the welding trials for this research. After proper tuning of
laser beam, laser welding experiments are conducted on AISI 304
grade sheets to evaluate the influence of various input parameters on
weld bead geometry i.e. bead width (BW) and depth of penetration
(DOP). From the laser welding results, it is noticed that the beam
power and welding speed are the two influencing parameters on
depth and width of the bead. Three dimensional finite element
simulation of high density heat source have been performed for laser
welding technique using finite element code ANSYS for predicting
the temperature profile of laser beam heat source on AISI 304
stainless steel sheets. The temperature dependent material properties
for AISI 304 stainless steel are taken into account in the simulation,
which has a great influence in computing the temperature profiles.
The latent heat of fusion is considered by the thermal enthalpy of
material for calculation of phase transition problem. A Gaussian
distribution of heat flux using a moving heat source with a conical
shape is used for analyzing the temperature profiles. Experimental
and simulated values for weld bead profiles are analyzed for stainless
steel material for different beam power, welding speed and beam
incident angle. The results obtained from the simulation are
compared with those from the experimental data and it is observed
that the results of numerical analysis (FEM) are in good agreement
with experimental results, with an overall percentage of error
estimated to be within ±6%.
Abstract: This paper presents a new approach for setting
frequency relays based on the dynamic of power system. A
simplified model of the power system based on the load-frequency
control loop will be developed to be used instead of the complete
model of the power system. The effects of the equipments and their
responses on the frequency variations of the power plant will be
investigated and then a method for adaptive settings of frequency
relays will be explained. The proposed method will be investigated
by analyzing a simplified model of a power plant by MATLAB
software.
Abstract: In this work, thermoelastic damping effect on the hemi- spherical shells is investigated. The material is selected silicon, and heat conduction equation for thermal flow is solved to obtain the temperature profile in which bending approximation with inextensional assumption of the model. Using the temperature profile, eigen-value analysis is performed to get the natural frequencies of hemispherical shells. Effects of mode numbers, radii and radial thicknesses of the model on the natural frequencies are analyzed in detail. Furthermore, the quality factor (Q-factor) is defined, and discussed for the ring and hemispherical shell.
Abstract: In this paper the development of a heat exchanger as a
pilot plant for educational purpose is discussed and the use of neural
network for controlling the process is being presented. The aim of the
study is to highlight the need of a specific Pseudo Random Binary
Sequence (PRBS) to excite a process under control. As the neural
network is a data driven technique, the method for data generation
plays an important role. In light of this a careful experimentation
procedure for data generation was crucial task. Heat exchange is a
complex process, which has a capacity and a time lag as process
elements. The proposed system is a typical pipe-in- pipe type heat
exchanger. The complexity of the system demands careful selection,
proper installation and commissioning. The temperature, flow, and
pressure sensors play a vital role in the control performance. The
final control element used is a pneumatically operated control valve.
While carrying out the experimentation on heat exchanger a welldrafted
procedure is followed giving utmost attention towards safety
of the system. The results obtained are encouraging and revealing
the fact that if the process details are known completely as far as
process parameters are concerned and utilities are well stabilized then
feedback systems are suitable, whereas neural network control
paradigm is useful for the processes with nonlinearity and less
knowledge about process. The implementation of NN control
reinforces the concepts of process control and NN control paradigm.
The result also underlined the importance of excitation signal
typically for that process. Data acquisition, processing, and
presentation in a typical format are the most important parameters
while validating the results.
Abstract: Nowadays, several techniques such as; Fuzzy
Inference System (FIS) and Neural Network (NN) are employed for
developing of the predictive models to estimate parameters of water
quality. The main objective of this study is to compare between the
predictive ability of the Adaptive Neuro-Fuzzy Inference System
(ANFIS) model and Artificial Neural Network (ANN) model to
estimate the Biochemical Oxygen Demand (BOD) on data from 11
sampling sites of Saen Saep canal in Bangkok, Thailand. The data is
obtained from the Department of Drainage and Sewerage, Bangkok
Metropolitan Administration, during 2004-2011. The five parameters
of water quality namely Dissolved Oxygen (DO), Chemical Oxygen
Demand (COD), Ammonia Nitrogen (NH3N), Nitrate Nitrogen
(NO3N), and Total Coliform bacteria (T-coliform) are used as the
input of the models. These water quality indices affect the
biochemical oxygen demand. The experimental results indicate that
the ANN model provides a higher correlation coefficient (R=0.73)
and a lower root mean square error (RMSE=4.53) than the
corresponding ANFIS model.
Abstract: Bidding is a very important business function to find
latent contractors of construction projects. Moreover, bid markup is
one of the most important decisions for a bidder to gain a reasonable
profit. Since the bidding system is a complex adaptive system, bidding
agent need a learning process to get more valuable knowledge for a bid,
especially from past public bidding information. In this paper, we
proposed an iterative agent leaning model for bidders to make markup
decisions. A classifier for public bidding information named PIBS is
developed to make full use of history data for classifying new bidding
information. The simulation and experimental study is performed to
show the validity of the proposed classifier. Some factors that affect
the validity of PIBS are also analyzed at the end of this work.
Abstract: Information and communication technology (ICT) has
become, within a very short time, one of the basic building blocks of
modern society. Many countries now understanding the importance
of ICT and mastering the basic skills and concepts of it as part of the
core of education. Organizations, experts and practitioners in the
education sector increasingly recognizing the importance of ICT in
supporting educational improvement and reform. This paper
addresses the convergence of ICT and education. When two
technologies are converging to each other, together they will generate
some great opportunities and challenges. This paper focuses on these
issues. In introduction section, it explains the ICT, education, and
ICT-enhanced education. In next section it describes need of ICT in
education, relationship between ICT skills and education, and stages
of teaching learning process. The next two sections describe
opportunities and challenges in integrating ICT in education. Finally
the concluding section summaries the idea and its usefulness.
Abstract: Understanding proteins functions is a major goal in
the post-genomic era. Proteins usually work in context of other
proteins and rarely function alone. Therefore, it is highly relevant to
study the interaction partners of a protein in order to understand its
function. Machine learning techniques have been widely applied to
predict protein-protein interactions. Kernel functions play an
important role for a successful machine learning technique. Choosing
the appropriate kernel function can lead to a better accuracy in a
binary classifier such as the support vector machines. In this paper,
we describe a Bayesian kernel for the support vector machine to
predict protein-protein interactions. The use of Bayesian kernel can
improve the classifier performance by incorporating the probability
characteristic of the available experimental protein-protein
interactions data that were compiled from different sources. In
addition, the probabilistic output from the Bayesian kernel can assist
biologists to conduct more research on the highly predicted
interactions. The results show that the accuracy of the classifier has
been improved using the Bayesian kernel compared to the standard
SVM kernels. These results imply that protein-protein interaction can
be predicted using Bayesian kernel with better accuracy compared to
the standard SVM kernels.
Abstract: State-based testing is frequently used in software testing. Test data generation is one of the key issues in software testing. A properly generated test suite may not only locate the errors in a software system, but also help in reducing the high cost associated with software testing. It is often desired that test data in the form of test sequences within a test suite can be automatically generated to achieve required test coverage. This paper proposes an Ant Colony Optimization approach to test data generation for the state-based software testing.
Abstract: This paper presents methodologies for developing an
intelligent CAD system assisting in analysis and design of
reconfigurable special machines. It describes a procedure for
determining feasibility of utilizing these machines for a given part
and presents a model for developing an intelligent CAD system. The
system analyzes geometrical and topological information of the given
part to determine possibility of the part being produced by
reconfigurable special machines from a technical point of view. Also
feasibility of the process from a economical point of view is
analyzed. Then the system determines proper positioning of the part
considering details of machining features and operations needed.
This involves determination of operation types, cutting tools and the
number of working stations needed. Upon completion of this stage
the overall layout of the machine and machining equipment required
are determined.
Abstract: Using a texture database, a statistical estimation of
spring-back was conducted in this study on the basis of statistical
analysis. Both spring-back in bending deformation and experimental
data related to the crystal orientation show significant dispersion.
Therefore, a probabilistic statistical approach was established for the
proper quantification of these values. Correlation was examined
among the parameters F(x) of spring-back, F(x) of the buildup fraction
to three orientations after 92° bending, and F(x) at an as-received part
on the basis of the three-parameter Weibull distribution. Consequent
spring-back estimation using a texture database yielded excellent
estimates compared with experimental values.
Abstract: The European countries that during the past two
decades based their exchange rate regimes on currency board
arrangement (CBA) are usually analysed from the perspective of
corner solution choice’s stabilisation effects. There is an open
discussion on the positive and negative background of a strict
exchange rate regime choice, although it should be seen as part of the
transition process towards the monetary union membership. The
focus of the paper is on the Baltic countries that after two decades of
a rigid exchange rate arrangement and strongly influenced by global
crisis are finishing their path towards the euro zone. Besides the
stabilising capacity, the CBA is highly vulnerable regime, with
limited developing potential. The rigidity of the exchange rate (and
monetary) system, despite the ensured credibility, do not leave
enough (or any) space for the adjustment and/or active crisis
management. Still, the Baltics are in a process of recovery, with fiscal
consolidation measures combined with (painful and politically
unpopular) measures of internal devaluation. Today, two of them
(Estonia and Latvia) are members of euro zone, fulfilling their
ultimate transition targets, but de facto exchanging one fixed regime
with another.
The paper analyses the challenges for the CBA in unstable
environment since the fixed regimes rely on imported stability and
are sensitive to external shocks. With limited monetary instruments,
these countries were oriented to the fiscal policies and used a
combination of internal devaluation and tax policy measures. Despite
their rather quick recovery, our second goal is to analyse the long
term influence that the measures had on the national economy.