Abstract: This paper presents a remote on-line diagnostic system
for vehicles via the use of On-Board Diagnostic (OBD), GPS, and 3G
techniques. The main parts of the proposed system are on-board
computer, vehicle monitor server, and vehicle status browser. First,
the on-board computer can obtain the location of deriver and vehicle
status from GPS receiver and OBD interface, respectively. Then
on-board computer will connect with the vehicle monitor server
through 3G network to transmit the real time vehicle system status.
Finally, vehicle status browser could show the remote vehicle status
including vehicle speed, engine rpm, battery voltage, engine coolant
temperature, and diagnostic trouble codes. According to the
experimental results, the proposed system can help fleet managers and
car knockers to understand the remote vehicle status. Therefore this
system can decrease the time of fleet management and vehicle repair
due to the fleet managers and car knockers who find the diagnostic
trouble messages in time.
Abstract: In this report, an OTA which is used in fully
differential pipelined ADC was described. Using gain-boost
architecture with difference-ended amplifier, this OTA achieve
high-gain and high-speed. Besides, the CMFB circuit is also used, and
some methods are concerned to improve the performance. Then, by
optimization the layout design, OTA-s mismatch was reduced. This
design was using TSMC 0.18um CMOS process and simulation both
schematic and layout in Cadence. The result of the simulation shows
that the OTA has a gain up to 80dB,a unity gain bandwidth of about
1.437GHz for a 2pF load, a slew rate is about 428V/μs, a output swing
is 0.2V~1.35V, with the power supply of 1.8V, the power
consumption is 88mW. This amplifier was used in a 10bit 150MHz
pipelined ADC.
Abstract: This paper analyzed the perception of e-commerce
application services by construction material traders in Malaysia.
Five attributes were tested: usability, reputation, trust, privacy and
familiarity. Study methodology consists of survey questionnaire and
statistical analysis that includes reliability analysis, factor analysis,
ANOVA and regression analysis. The respondents were construction
material traders, including hardware stores in Klang Valley, Kuala
Lumpur.
Findings support that usability and familiarity with e-commerce
services in Malaysia have insignificant influence on the acceptance of
e-commerce application. However, reputation, trust and privacy
attributes have significant influence on the choice of e-commerce
acceptance by construction material traders. E-commerce
applications studied included customer database, e-selling, emarketing,
e-payment, e-buying and online advertising. Assumptions
are made that traders have basic knowledge and exposure to ICT
services. i.e. internet service and computers. Study concludes that
reputation, privacy and trust are the three website attributes that
influence the acceptance of e-commerce by construction material
traders.
Abstract: Monitoring the tool flank wear without affecting the
throughput is considered as the prudent method in production
technology. The examination has to be done without affecting the
machining process. In this paper we proposed a novel work that is
used to determine tool flank wear by observing the sound signals
emitted during the turning process. The work-piece material we used
here is steel and aluminum and the cutting insert was carbide
material. Two different cutting speeds were used in this work. The
feed rate and the cutting depth were constant whereas the flank wear
was a variable. The emitted sound signal of a fresh tool (0 mm flank
wear) a slightly worn tool (0.2 -0.25 mm flank wear) and a severely
worn tool (0.4mm and above flank wear) during turning process were
recorded separately using a high sensitive microphone. Analysis
using Singular Value Decomposition was done on these sound
signals to extract the feature sound components. Observation of the
results showed that an increase in tool flank wear correlates with an
increase in the values of SVD features produced out of the sound
signals for both the materials. Hence it can be concluded that wear
monitoring of tool flank during turning process using SVD features
with the Fuzzy C means classification on the emitted sound signal is
a potential and relatively simple method.
Abstract: Forecasting the values of the indicators, which
characterize the effectiveness of performance of organizations is of
great importance for their successful development. Such forecasting
is necessary in order to assess the current state and to foresee future
developments, so that measures to improve the organization-s
activity could be undertaken in time. The article presents an
overview of the applied mathematical and statistical methods for
developing forecasts. Special attention is paid to artificial neural
networks as a forecasting tool. Their strengths and weaknesses are
analyzed and a synopsis is made of the application of artificial neural
networks in the field of forecasting of the values of different
education efficiency indicators. A method of evaluation of the
activity of universities using the Balanced Scorecard is proposed and
Key Performance Indicators for assessment of e-learning are
selected. Resulting indicators for the evaluation of efficiency of the
activity are proposed. An artificial neural network is constructed and
applied in the forecasting of the values of indicators for e-learning
efficiency on the basis of the KPI values.
Abstract: Prediction of fault-prone modules provides one way to
support software quality engineering. Clustering is used to determine
the intrinsic grouping in a set of unlabeled data. Among various
clustering techniques available in literature K-Means clustering
approach is most widely being used. This paper introduces K-Means
based Clustering approach for software finding the fault proneness of
the Object-Oriented systems. The contribution of this paper is that it
has used Metric values of JEdit open source software for generation
of the rules for the categorization of software modules in the
categories of Faulty and non faulty modules and thereafter
empirically validation is performed. The results are measured in
terms of accuracy of prediction, probability of Detection and
Probability of False Alarms.
Abstract: A numerical investigation of surface heat transfer
characteristics of turbulent air flows in different parallel plate
grooved channels is performed using CFD code. The results are
obtained for Reynolds number ranging from 10,000 to 30,000 and for
arc-shaped and rectangular grooved channels. The influence of
different geometric parameters of dimples as well as the number of
them and the geometric and thermophysical properties of channel
walls are studied. It is found that there exists an optimum value for
depth of dimples in which the largest wall heat flux can be achieved.
Also, the results show a critical value for the ratio of wall thermal
conductivity to the one of fluid in which the dependence of wall heat
flux to this ratio almost vanishes. In most cases examined, heat
transfer enhancement is larger for arc-shaped grooved channels than
rectangular ones.
Abstract: This paper aims at to develop a robust optimization methodology for the mechatronic modules of machine tools by considering all important characteristics from all structural and control domains in one single process. The relationship between these two domains is strongly coupled. In order to reduce the disturbance caused by parameters in either one, the mechanical and controller design domains need to be integrated. Therefore, the concurrent integrated design method Design For Control (DFC), will be employed in this paper. In this connect, it is not only applied to achieve minimal power consumption but also enhance structural performance and system response at same time. To investigate the method for integrated optimization, a mechatronic feed drive system of the machine tools is used as a design platform. Pro/Engineer and AnSys are first used to build the 3D model to analyze and design structure parameters such as elastic deformation, nature frequency and component size, based on their effects and sensitivities to the structure. In addition, the robust controller,based on Quantitative Feedback Theory (QFT), will be applied to determine proper control parameters for the controller. Therefore, overall physical properties of the machine tool will be obtained in the initial stage. Finally, the technology of design for control will be carried out to modify the structural and control parameters to achieve overall system performance. Hence, the corresponding productivity is expected to be greatly improved.
Abstract: The objective of the research was to evaluate the
quality of milk pomade sweet – sherbet packed in different packaging
materials (Multibarrier 60, met.BOPET/PE, Aluthen), by several
packaging technologies – active and modified atmosphere (MAP)
(consisting of 100% CO2), and control – in air ambiance.
Experiments were carried out at the Faculty of Food Technology of
Latvia University of Agriculture. Samples were stored at the room
temperature +21±1 °C. The physiochemical properties – weight
losses, moisture, hardening, colour and changes in headspace
atmosphere concentration (CO2 and O2) of packs were analysed
before packaging and after 2, 4, 6, 8, 10 and 12 storage weeks.
Abstract: In order to study the effect of plant density and
competition of wheat with field bindweed (Convolvulus arvensis) on
yield and agronomical properties of wheat(Triticum Sativum) in
irrigated conditions, a factorial experiment as the base of complete
randomize block design in three replication was conducted at the
field of Kamalvand in khoramabad (Lorestan) region of Iran during
2008-2009. Three plant density (Factor A=200, 230 and 260kg/ha)
three cultivar (Factor B=Bahar,Pishtaz and Alvand) and weed control
(Factor C= control and no control of weeds)were assigned in
experiment. Results show that: Plant density had significant effect
(statistically) on seed yield, 1000 seed weight, weed density and dry
weight of weeds, seed yield and harvest index had been meaningful
effect for cultivars. The interaction between plant density and
cultivars for weed density, seed yield, thousand seed weight and
harvest index were significant. 260 kg/ha (plant density) of wheat had
more effect on increasing of seed yield in Bahar cultivar wheat in
khoramabad region of Iran.
Abstract: Safety, river environment, and sediment utilization are the elements of the target of sediment management. As a change in an element by sediment management, may affect the other two elements, and the priority among three elements depends on stakeholders. It is necessary to develop a method to evaluate the effect of sediment management on each element and an integrated evaluation method for socio-economic effect. In this study, taking Mount Merapi basin as an investigation field, the method for an active volcanic basin was developed. An integrated evaluation method for sediment management was discussed from a socio-economic point on safety, environment, and sediment utilization and a case study of sediment management was evaluated by means of this method. To evaluate the effect of sediment management, some parameters on safety, utilization, and environment have been introduced. From a utilization point of view, job opportunity, additional income of local people, and tax income to local government were used to evaluate the effectiveness of sediment management. The risk degree of river infrastructure was used to describe the effect of sediment management on a safety aspect. To evaluate the effects of sediment management on environment, the mean diameter of grain size distribution of riverbed surface was used. On the coordinate system designating these elements, the direction of change in basin condition by sediment management can be predicted, so that the most preferable sediment management can be decided. The results indicate that the cases of sediment management tend to give the negative impacts on sediment utilization. However, these sediment managements will give positive impacts on safety and environment condition. Evaluation result from a social-economic point of view shows that the case study of sediment management reduces job opportunity and additional income for inhabitants as well as tax income for government. Therefore, it is necessary to make another policy for creating job opportunity for inhabitants to support these sediment managements.
Abstract: Abrasive waterjet is a novel machining process capable of processing wide range of hard-to-machine materials. This research addresses modeling and optimization of the process parameters for this machining technique. To model the process a set of experimental data has been used to evaluate the effects of various parameter settings in cutting 6063-T6 aluminum alloy. The process variables considered here include nozzle diameter, jet traverse rate, jet pressure and abrasive flow rate. Depth of cut, as one of the most important output characteristics, has been evaluated based on different parameter settings. The Taguchi method and regression modeling are used in order to establish the relationships between input and output parameters. The adequacy of the model is evaluated using analysis of variance (ANOVA) technique. The pairwise effects of process parameters settings on process response outputs are also shown graphically. The proposed model is then embedded into a Simulated Annealing algorithm to optimize the process parameters. The optimization is carried out for any desired values of depth of cut. The objective is to determine proper levels of process parameters in order to obtain a certain level of depth of cut. Computational results demonstrate that the proposed solution procedure is quite effective in solving such multi-variable problems.
Abstract: In this work we investigated the behavior of methane
hydrates dispersed in crude oils from different fields at temperatures
below 0°C. In case of crude oil emulsion the size of water droplets is
in the range of 50e100"m. The size of hydrate particles formed from
droplets is the same. The self-preservation is not expected in this
field. However, the self-preservation of hydrates with the size of
particles 24±18"m (electron microscopy data) in suspensions is
observed. Similar results were obtained for four different kinds of
crude oil and model system such as asphaltenes, resins and wax in ndecane.
This result can allow developing effective methods to prevent
the formation and elimination of gas-hydrate plugs in pipelines under
low temperature conditions (e. g. in Eastern Siberia). There is a
prospective to use experiment results for working out the technology
of associated petroleum gas recovery.
Abstract: We present a dual-band (Cellular & PCS) dual-path
zero-IF receiver for CDMA2000 diversity, monitoring and
simultaneous-GPS. The secondary path is a SAW-less diversity
CDMA receiver which can be also used for advanced features like
monitoring when supported with an additional external VCO. A GPS
receiver is integrated with its dedicated VCO allowing simultaneous
positioning during a cellular call. The circuit is implemented in a
0.25μm 40GHz-fT BiCMOS process and uses a HVQFN 56-pin
package. It consumes a maximum 300mW from a 2.8V supply in
dual-modes. The chip area is 12.8mm2.
Abstract: This paper considers a scheduling problem in flexible
flow shops environment with the aim of minimizing two important
criteria including makespan and cumulative tardiness of jobs. Since
the proposed problem is known as an Np-hard problem in literature,
we have to develop a meta-heuristic to solve it. We considered
general structure of Genetic Algorithm (GA) and developed a new
version of that based on Data Envelopment Analysis (DEA). Two
objective functions assumed as two different inputs for each Decision
Making Unit (DMU). In this paper we focused on efficiency score of
DMUs and efficient frontier concept in DEA technique. After
introducing the method we defined two different scenarios with
considering two types of mutation operator. Also we provided an
experimental design with some computational results to show the
performance of algorithm. The results show that the algorithm
implements in a reasonable time.
Abstract: In this article, the design of a Supply Chain Network
(SCN) consisting of several suppliers, production plants, distribution
centers and retailers, is considered. Demands of retailers are
considered stochastic parameters, so we generate amounts of data via
simulation to extract a few demand scenarios. Then a mixed integer
two-stage programming model is developed to optimize
simultaneously two objectives: (1) minimization the fixed and
variable cost, (2) maximization the service level. A weighting method
is utilized to solve this two objective problem and a numerical
example is made to show the performance of the model.
Abstract: This paper demonstrates a model of an e-Learning
system based on nowadays learning theory and distant education
practice. The relationships in the model are designed to be simple
and functional and do not necessarily represent any particular e-
Learning environments. It is meant to be a generic e-Learning
system model with implications for any distant education course
instructional design. It allows online instructors to move away from
the discrepancy between the courses and body of knowledge. The
interrelationships of four primary sectors that are at the e-Learning
system are presented in this paper. This integrated model includes
[1] pedagogy, [2] technology, [3] teaching, and [4] learning. There
are interactions within each of these sectors depicted by system loop
map.
Abstract: Public bus service plays a significant role in our
society as people movers and to facilitate travels within towns and districts. The quality of service of public bus is always being
regarded as poor, or rather, underestimated as second class means of transportation. Reliability of service, or the ability to deliver service as planned, is one key element in perceiving the quality of bus service and the punctuality index is one of the performance parameters in determining the service reliability. This study
concentrates on evaluating the reliability performance of bus operation using punctuality index assessment. A week data for each
of six city bus routes is recorded using the on-board methodology to calculate the punctuality index for city bus service in Kota Bharu. The results revealed that the punctuality index for the whole city bus network is 94.25% (LOS B).
Abstract: Technology assessment is a vital part of decision process in manufacturing, particularly for decisions on selection of new sustainable manufacturing processes. To assess these processes, a matrix approach is introduced and sustainability assessment models are developed. Case studies show that the matrix-based approach provides a flexible and practical way for sustainability evaluation of new manufacturing technologies such as those used in surface coating. The technology assessment of coating processes reveals that compared with powder coating, the sol-gel coating can deliver better technical, economical and environmental sustainability with respect to the selected sustainability evaluation criteria for a decorative coating application of car wheels.
Abstract: Image retrieval is a topic where scientific interest is currently high. The important steps associated with image retrieval system are the extraction of discriminative features and a feasible similarity metric for retrieving the database images that are similar in content with the search image. Gabor filtering is a widely adopted technique for feature extraction from the texture images. The recently proposed sparsity promoting l1-norm minimization technique finds the sparsest solution of an under-determined system of linear equations. In the present paper, the l1-norm minimization technique as a similarity metric is used in image retrieval. It is demonstrated through simulation results that the l1-norm minimization technique provides a promising alternative to existing similarity metrics. In particular, the cases where the l1-norm minimization technique works better than the Euclidean distance metric are singled out.