Abstract: Two-dimensional finite element model was created in this work to investigate the stresses distribution within rock-like samples with offset open non-persistent joints under biaxial loading. The results of this study have explained the fracture mechanisms observed in tests on rock-like material with open non-persistent offset joints [1]. Finite element code SAP2000 was used to study the stresses distribution within the specimens. Four-nodded isoperimetric plain strain element with two degree of freedom per node, and the three-nodded constant strain triangular element with two degree of freedom per node were used in the present study.The results of the present study explained the formation of wing cracks at the tip of the joints for low confining stress as well as the formation of wing cracks at the middle of the joint for the higher confining stress. High shear stresses found in the numerical study at the tip of the joints explained the formation of secondary cracks at the tip of the joints in the experimental study. The study results coincide with the experimental observations which showed that for bridge inclination of 0o, the coalescence occurred due to shear failure and for bridge inclination of 90o the coalescence occurred due to tensile failure while for the other bridge inclinations coalescence occurred due to mixed tensile and shear failure.
Abstract: Sensors possess several properties of physical
measures. Whether devices that convert a sensed signal into an
electrical signal, chemical sensors and biosensors, thus all these
sensors can be considered as an interface between the physical and
electrical equipment. The problem is the analysis of the multitudes of
saved settings as input variables. However, they do not all have the
same level of influence on the outputs. In order to identify the most
sensitive parameters, those that can guide users in gathering
information on the ground and in the process of model calibration
and sensitivity analysis for the effect of each change made.
Mathematical models used for processing become very complex.
In this paper a fuzzy rule-based system is proposed as a solution
for this problem. The system collects the available signals
information from sensors. Moreover, the system allows the study of
the influence of the various factors that take part in the decision
system. Since its inception fuzzy set theory has been regarded as a
formalism suitable to deal with the imprecision intrinsic to many
problems. At the same time, fuzzy sets allow to use symbolic models.
In this study an example was applied for resolving variety of
physiological parameters that define human health state. The
application system was done for medical diagnosis help. The inputs
are the signals expressed the cardiovascular system parameters, blood
pressure, Respiratory system paramsystem was done, it will be able
to predict the state of patient according any input values.
Abstract: It is shown that the relationship of tick-borne
encephalitis virus with the human body comes in two ways, the
development of acute infection with the outcome in convalescence
and long stay by the virus in the body, its persistence in the nervous
tissue with periodic reactivation and prolonged circulating
immunoglobulin M. In spite of the fact that tick-borne encephalitis
virus has a tropism for nerve tissue, involvement in the process of
blood cells is an integral component of the infection. Comprehensive
study of the relation of factors of innate and adaptive immunity in the
tick-borne encephalitis providing insight into the features of chronic
disease.
Abstract: The effect of varying holding temperature on hatching success, occurrence of deformities and mortality rates were investigated for goldlined seabream eggs. Wild broodstock (600 g) were stocked at a 2:1 male-female ratio in a 2 m3 fiberglass tank supplied with filtered seawater (37 g L-1 salinity, temp. range 24±0.5 oC [day] and 22±1 oC [night], DO2 in excess of 5.0mg L-1). Females were injected with 200 IU kg-1 HCG between 08.00 and 10.00 h and returned to tanks to spawn following which eggs were collected by hand using a 100μm net. Fertilized eggs at the gastrulation stage (120 L-1) were randomly placed into one of 12 experimental 6 L aerated (DO2 5 mg L-1) plastic containers with water temperatures maintained at 24±0.5 oC (ambient), 26±0.5 oC, 28± 0.5 oC and 30±0.5 oC using thermostats. Each treatment was undertaken in triplicate using a 12:12 photophase:scotophase photoperiod. No differences were recorded between eggs reared at 24 and 26 oC with respect to viability, deformity, mortality or unhatched egg rates. Increasing temperature reduced the number of viable eggs with those at 30 oC returning poorest performance (P < 0.05). Mortality levels were lowest for eggs incubated at 24 and 26 oC. The greatest level of deformities recorded was that for eggs reared at 28 oC.
Abstract: Many organisations are nowadays interested to adopt
lean manufacturing strategy that would enable them to compete in
this competitive globalisation market. In this respect, it is necessary
to assess the implementation of lean manufacturing in different
organisations so that the important best practices can be identified.
This paper describes the development of key areas which will be
used to assess the adoption and implementation of lean
manufacturing practices. There are some key areas developed to
evaluate and reduce the most optimal projects so as to enhance their
production efficiency and increase the purpose of the economic
benefits of the manufacturing unit.
Lean manufacturing is becoming lean enterprise by treating its
customers and suppliers as partners. This gives the extra edge in
today-s cost and time competitive markets. The organisation is
becoming strong in all the conventional competition points. They are
Price, Quality and Delivery. Lean enterprise owners can deliver high
quality products quickly, with low price.
Abstract: International literature emphasizes on the concern regarding the phenomenon of aggression in hospital. This paper focuses on the reality of aggressive interactions reigning within an emergency triage involving three chaps of protagonists: the professionals, the patients and their carers. The data collection was made from a grid of observation, in which the various variables exposed in the literature were integrated. They observations took place around the clock, for three weeks, at the rate of one week a month. In this research 331 aggressive interactions have been listed and analyzed by means of the software SPSS. This research is one of the very few continuous observation surveys in the literature. It shows the various human factors at play in the emergence of aggressive interaction. The data may be used both for taking steps in primary prevention, thanks to the analysis of interaction modes, and in secondary prevention by integrating the useful results in situational prevention.
Abstract: This article presents a detailed analysis and comparative
performance evaluation of model reference adaptive control systems.
In contrast to classical control theory, adaptive control methods allow
to deal with time-variant processes. Inspired by the works [1] and
[2], two methods based on the MIT rule and Lyapunov rule are
applied to a linear first order system. The system is simulated and
it is investigated how changes to the adaptation gain affect the
system performance. Furthermore, variations in the reference model
parameters, that is changing the desired closed-loop behaviour are
examinded.
Abstract: In the present study, the effects of ultrasound as
emerging technology were investigated on germination stimulation,
amount of alpha-amylase activity on dry barley seeds before steeping
stage of malting process. All experiments were carried out at 20 KHz
on the ultrasonic generator in 3 different ultrasonic intensities (20, 60
and 100% setting from total power of device) and time (5, 10 and 15
min) at constant temperature (30C). For determining the effects of
these parameters on enzyme the Fuwa method assay based on the
decreased staining value of blue starch–iodine complexes employed
for measurement an activity. The results of these assays were
analyzed by Qualitek4 software using the Taguchi statistical method
to evaluate the factor-s effects on enzyme activity. It has been found
that when malting barley is irradiated with an ultrasonic power, a
stimulating effect occurs as to the enzyme activity.
Abstract: In this study, a low temperature sensor highly selective to CO in presence of methane is fabricated by using 4 nm SnO2 quantum dots (QDs) prepared by sonication assisted precipitation. SnCl4 aqueous solution was precipitated by ammonia under sonication, which continued for 2 h. A part of the sample was then dried and calcined at 400°C for 1.5 h and characterized by XRD and BET. The average particle size and the specific surface area of the SnO2 QDs as well as their sensing properties were compared with the SnO2 nano-particles which were prepared by conventional sol-gel method. The BET surface area of sonochemically as-prepared product and the one calcined at 400°C after 1.5 hr are 257 m2/gr and 212 m2/gr respectively while the specific surface area for SnO2 nanoparticles prepared by conventional sol-gel method is about 80m2/gr. XRD spectra revealed pure crystalline phase of SnO2 is formed for both as-prepared and calcined samples of SnO2 QDs. However, for the sample prepared by sol-gel method and calcined at 400°C SnO crystals are detected along with those of SnO2. Quantum dots of SnO2 show exceedingly high sensitivity to CO with different concentrations of 100, 300 and 1000 ppm in whole range of temperature (25- 350°C). At 50°C a sensitivity of 27 was obtained for 1000 ppm CO, which increases to a maximum of 147 when the temperature rises to 225°C and then drops off while the maximum sensitivity for the SnO2 sample prepared by the sol-gel method was obtained at 300°C with the amount of 47.2. At the same time no sensitivity to methane is observed in whole range of temperatures for SnO2 QDs. The response and recovery times of the sensor sharply decreases with temperature, while the high selectivity to CO does not deteriorate.
Abstract: The aim of this paper is to study the oblique
stagnation point flow on vertical plate with uniform surface heat flux
in presence of magnetic field. Using Stream function, partial
differential equations corresponding to the momentum and energy
equations are converted into non-linear ordinary differential
equations. Numerical solutions of these equations are obtained using
Runge-Kutta Fehlberg method with the help of shooting technique.
In the present work the effects of striking angle, magnetic field
parameter, Grashoff number, the Prandtl number on velocity and heat
transfer characteristics have been discussed. Effect of above
mentioned parameter on the position of stagnation point are also
studied.
Abstract: Transmission network expansion planning (TNEP) is an important component of power system planning that its task is to minimize the network construction and operational cost while satisfying the demand increasing, imposed technical and economic conditions. Up till now, various methods have been presented to solve the static transmission network expansion planning (STNEP) problem. But in all of these methods, the lines adequacy rate has not been studied after the planning horizon, i.e. when the expanded network misses its adequacy and needs to be expanded again. In this paper, in order to take transmission lines condition after expansion in to account from the line loading view point, the adequacy of transmission network is considered for solution of STNEP problem. To obtain optimal network arrangement, a decimal codification genetic algorithm (DCGA) is being used for minimizing the network construction and operational cost. The effectiveness of the proposed idea is tested on the Garver's six-bus network. The results evaluation reveals that the annual worth of network adequacy has a considerable effect on the network arrangement. In addition, the obtained network, based on the DCGA, has lower investment cost and higher adequacy rate. Thus, the network satisfies the requirements of delivering electric power more safely and reliably to load centers.
Abstract: The modified Claus process is the major technology
for the recovery of elemental sulfur from hydrogen sulfide. The
chemical reactions that can occur in the reaction furnace are
numerous and many byproducts such as carbon disulfide and carbon
carbonyl sulfide are produced. These compounds can often contribute
from 20 to 50% of the pollutants and therefore, should be hydrolyzed
in the catalytic converter. The inlet temperature of the first catalytic
reactor should be maintained over than 250 °C, to hydrolyze COS
and CS2. In this paper, the various configurations for the first
converter reheating of sulfur recovery unit are investigated. As a
result, the performance of each method is presented for a typical
clause unit. The results show that the hot gas method seems to be
better than the other methods.
Abstract: Computer networks are essential part in computerbased
information systems. The performance of these networks has a
great influence on the whole information system. Measuring the
usability criteria and customers satisfaction on small computer
network is very important. In this article, an effective approach for
measuring the usability of business network in an information system
is introduced. The usability process for networking provides us with a
flexible and a cost-effective way to assess the usability of a network
and its products. In addition, the proposed approach can be used to
certify network product usability late in the development cycle.
Furthermore, it can be used to help in developing usable interfaces
very early in the cycle and to give a way to measure, track, and
improve usability. Moreover, a new approach for fast information
processing over computer networks is presented. The entire data are
collected together in a long vector and then tested as a one input
pattern. Proposed fast time delay neural networks (FTDNNs) use
cross correlation in the frequency domain between the tested data and
the input weights of neural networks. It is proved mathematically and
practically that the number of computation steps required for the
presented time delay neural networks is less than that needed by
conventional time delay neural networks (CTDNNs). Simulation
results using MATLAB confirm the theoretical computations.
Abstract: Construction cost in India is increasing at around 50
per cent over the average inflation levels. It have registered increase
of up to 15 per cent every year, primarily due to cost of basic
building materials such as steel, cement, bricks, timber and other
inputs as well as cost of labour. As a result, the cost of construction
using conventional building materials and construction is becoming
beyond the affordable limits particularly for low-income groups of
population as well as a large cross section of the middle - income
groups. Therefore, there is a need to adopt cost-effective construction
methods either by up-gradation of traditional technologies using local
resources or applying modern construction materials and techniques
with efficient inputs leading to economic solutions. This has become
the most relevant aspect in the context of the large volume of housing
to be constructed in both rural and urban areas and the consideration
of limitations in the availability of resources such as building
materials and finance. This paper makes an overview of the housing
status in India and adoption of appropriate and cost effective
technologies in the country.
Abstract: Carbon tetrachloride (CCl4) is a well-known
hepatotoxin and exposure to this chemical is known to induce
oxidative stress and causes liver injury by the formation of free
radicals. Flacourtia indica commonly known as 'Baichi' has been
reported as an effective remedy for the treatment of a variety of
diseases. The objective of this study was to investigate the
hepatoprotective activity of aqueous extract of leaves of Flacourtia
indica against CCl4 induced hepatotoxicity. Animals were pretreated
with the aqueous extract of Flacourtia indica (250 & 500 mg/kg
body weight) for one week and then challenged with CCl4 (1.5 ml/kg
bw) in olive oil (1:1, v/v) on 7th day. Serum marker enzymes (ALP,
AST, ALT, Total Protein & Total Bilirubin) and TBARS level
(Marker for oxidative stress) were estimated in all the study groups.
Alteration in the levels of biochemical markers of hepatic damage
like AST, ALT, ALP, Total Protein, Total Bilirubin and lipid
peroxides (TBARS) were tested in both CCl4 treated and extract
treated groups. CCl4 has enhanced the AST, ALT, ALP and the
Lipid peroxides (TBARS) in liver. Treatment of aqueous extract of
Flacourtia indica leaves (250 & 500 mg/kg) exhibited a significant
protective effect by altering the serum levels of AST, ALT, ALP,
Total Protein, Total Bilirubin and liver TBARS. These biochemical
observations were supported by histopathological study of liver
sections. From this preliminary study it has been concluded that the
aqueous extract of the leaves of Flacourtia indica protects liver
against oxidative damages and could be used as an effective protector
against CCl4 induced hepatic damage. Our findings suggested that
Flacourtia indica possessed good hepatoprotective activity
Abstract: The Algorithm 2 for a n-link manipulator movement amidst arbitrary unknown static obstacles for a case when a sensor system supplies information about local neighborhoods of different points in the configuration space is presented. The Algorithm 2 guarantees the reaching of a target position in a finite number of steps. The Algorithm 2 is reduced to a finite number of calls of a subroutine for planning a trajectory in the presence of known forbidden states. The polynomial approximation algorithm which is used as the subroutine is presented. The results of the Algorithm2 implementation are given.
Abstract: This study systemizes processes and methods in
wooden furniture design that contains uniqueness in function and
aesthetics. The study was done by research and analysis for
designer-s consideration factors that affect function and production.
Therefore, the study result indicates that such factors are design
process (planning for design, product specifications, concept design,
product architecture, industrial design, production), design evaluation
as well as wooden furniture design dependent factors i.e. art (art
style; furniture history, form), functionality (the strength and
durability, area place, using), material (appropriate to function, wood
mechanical properties), joints, cost, safety, and social responsibility.
Specifically, all aforementioned factors affect good design. Resulting
from direct experience gained through user-s usage, the designer
must design the wooden furniture systemically and effectively. As a
result, this study selected dinning armchair as a case study with all
involving factors and all design process stated in this study.
Abstract: In this study, The physico-chemical and nutritional
properties of `Musmula` Medlar (Mespilus germanica L.) fruit and
seed grown in Northeast Anatolia was investigated. In the fruit,
length, width, thickness, weight, total soluble solids, colour (1),
colour (2) [L, a, b values], protein, crude ash, crude fiber, crude oil,
texture and pH were determinated as 4.34 cm, 4.22 cm, 3.67 cm,
38.36 g, 23.97 %, S60O60Y41,, [53.85, 17.15, 33.75], 1.06 %, 0.79 %,
4.24 %, 0.005 %, 1.21 kg/cm2 and 4.26 respectively. Also, pulp ratio,
seed ratio and pulp/seed ratio were found to be 92.88 %, 7.11 % and
14.07 %, respectively. In addition, the mineral composition of medlar
fruit in Northeast Anatolia was studied. In the fruit, 23 minerals were
analyzed and 19 minerals were present at detectable levels. The
medlar fruit was richest in potassium (6962 ppm), calcium (1186.378
ppm), magnesium (1070.08 ppm) and phosphor (763.425 ppm).
Abstract: Accurately predicting non-peak traffic is crucial to
daily traffic for all forecasting models. In the paper, least squares
support vector machines (LS-SVMs) are investigated to solve such a
practical problem. It is the first time to apply the approach and analyze
the forecast performance in the domain. For comparison purpose, two
parametric and two non-parametric techniques are selected because of
their effectiveness proved in past research. Having good
generalization ability and guaranteeing global minima, LS-SVMs
perform better than the others. Providing sufficient improvement in
stability and robustness reveals that the approach is practically
promising.
Abstract: Urbanization and related anthropogenic modifications
cause extent of habitat fragmentation and directly lead to decline of
local biodiversity. Conservation biologists advocate corridor creation
as one approach to rescue biodiversity. Here we examine the utility of
roads as corridors in preserving plant diversity by investigating
roadside vegetation in Yellow River Delta (YRD), China. We
examined the spatio-temporal distribution pattern of plant species
richness, diversity and composition along roadside. The results
suggest that roads, as dispersal conduits, increase occurrence
probability of new settlers to a new area, meanwhile, roads accumulate
the greater propagule pressure and favourable survival condition
during operation phase. As a result, more species, including native and
alien plants, non- halophyte and halophyte species, threatened and
cosmopolitic species, were found prosperous at roadside. Roadside
may be a refuge for more species, and the pattern of vegetation
distribution is affected by road age and the distance from road verge.