Abstract: Hydrogen is an important chemical in many industries
and it is expected to become one of the major fuels for energy
generation in the future. Unfortunately, hydrogen does not exist in its
elemental form in nature and therefore has to be produced from
hydrocarbons, hydrogen-containing compounds or water.
Above its critical point (374.8oC and 22.1MPa), water has lower
density and viscosity, and a higher heat capacity than those of
ambient water. Mass transfer in supercritical water (SCW) is
enhanced due to its increased diffusivity and transport ability. The
reduced dielectric constant makes supercritical water a better solvent
for organic compounds and gases. Hence, due to the aforementioned
desirable properties, there is a growing interest toward studies
regarding the gasification of organic matter containing biomass or
model biomass solutions in supercritical water.
In this study, hydrogen and biofuel production by the catalytic
gasification of 2-Propanol in supercritical conditions of water was
investigated. Pt/Al2O3and Ni/Al2O3were the catalysts used in the
gasification reactions. All of the experiments were performed under a
constant pressure of 25MPa. The effects of five reaction temperatures
(400, 450, 500, 550 and 600°C) and five reaction times (10, 15, 20,
25 and 30 s) on the gasification yield and flammable component
content were investigated.
Abstract: This paper solves the environmental/ economic dispatch
power system problem using the Non-dominated Sorting Genetic
Algorithm-II (NSGA-II) and its hybrid with a Convergence Accelerator
Operator (CAO), called the NSGA-II/CAO. These multiobjective
evolutionary algorithms were applied to the standard IEEE 30-bus
six-generator test system. Several optimization runs were carried out
on different cases of problem complexity. Different quality measure
which compare the performance of the two solution techniques were
considered. The results demonstrated that the inclusion of the CAO
in the original NSGA-II improves its convergence while preserving
the diversity properties of the solution set.
Abstract: Water hyacinth has been used in aquatic systems for
wastewater purification in many years worldwide. The role of water
hyacinth (Eichhornia crassipes) species in polishing nitrate and
phosphorus concentration from municipal wastewater treatment plant
effluent by phytoremediation method was evaluated. The objective
of this project is to determine the removal efficiency of water
hyacinth in polishing nitrate and phosphorus, as well as chemical
oxygen demand (COD) and ammonia. Water hyacinth is considered
as the most efficient aquatic plant used in removing vast range of
pollutants such as organic matters, nutrients and heavy metals. Water
hyacinth, also referred as macrophytes, were cultivated in the
treatment house in a reactor tank of approximately 90(L) x 40(W) x
25(H) in dimension and built with three compartments. Three water
hyacinths were placed in each compartments and water sample in
each compartment were collected in every two days. The plant
observation was conducted by weight measurement, plant uptake and
new young shoot development. Water hyacinth effectively removed
approximately 49% of COD, 81% of ammonia, 67% of phosphorus
and 92% of nitrate. It also showed significant growth rate at starting
from day 6 with 0.33 shoot/day and they kept developing up to 0.38
shoot/day at the end of day 24. From the studies conducted, it was
proved that water hyacinth is capable of polishing the effluent of
municipal wastewater which contains undesirable amount of nitrate
and phosphorus concentration.
Abstract: Based on the homotopy perturbation method (HPM)
and Padé approximants (PA), approximate and exact solutions are
obtained for cubic Boussinesq and modified Boussinesq equations.
The obtained solutions contain solitary waves, rational solutions.
HPM is used for analytic treatment to those equations and PA for
increasing the convergence region of the HPM analytical solution.
The results reveal that the HPM with the enhancement of PA is a
very effective, convenient and quite accurate to such types of partial
differential equations.
Abstract: Collaborative working environments for distance
education can be considered as a more generic form of contemporary
remote labs. At present, the majority of existing real laboratories are
not constructed to allow the involved participants to collaborate in
real time. To make this revolutionary learning environment possible
we must allow the different users to carry out an experiment
simultaneously. In recent times, multi-user environments are
successfully applied in many applications such as air traffic control
systems, team-oriented military systems, chat-text tools, multi-player
games etc. Thus, understanding the ideas and techniques behind these
systems could be of great importance in the contribution of ideas to
our e-learning environment for collaborative working. In this
investigation, collaborative working environments from theoretical
and practical perspectives are considered in order to build an
effective collaborative real laboratory, which allows two students or
more to conduct remote experiments at the same time as a team. In
order to achieve this goal, we have implemented distributed system
architecture, enabling students to obtain an automated help by either
a human tutor or a rule-based e-tutor.
Abstract: In this paper we discuss the effect of unbounded particle interaction operator on particle growth and we study how this can address the choice of appropriate time steps of the numerical simulation. We provide also rigorous mathematical proofs showing that large particles become dominating with increasing time while small particles contribute negligibly. Second, we discuss the efficiency of the algorithm by performing numerical simulations tests and by comparing the simulated solutions with some known analytic solutions to the Smoluchowski equation.
Abstract: In this paper we present a hybrid search algorithm for
solving constraint satisfaction and optimization problems. This
algorithm combines ideas of two basic approaches: complete and
incomplete algorithms which also known as systematic search and
local search algorithms. Different characteristics of systematic search
and local search methods are complementary. Therefore we have
tried to get the advantages of both approaches in the presented
algorithm. The major advantage of presented algorithm is finding
partial sound solution for complicated problems which their complete
solution could not be found in a reasonable time. This algorithm
results are compared with other algorithms using the well known
n-queens problem.
Abstract: Partial discharge (PD) detection is an important
method to evaluate the insulation condition of metal-clad apparatus.
Non-intrusive sensors which are easy to install and have no
interruptions on operation are preferred in onsite PD detection.
However, it often lacks of accuracy due to the interferences in PD
signals. In this paper a novel PD extraction method that uses frequency
analysis and entropy based time-frequency (TF) analysis is introduced.
The repetitive pulses from convertor are first removed via frequency
analysis. Then, the relative entropy and relative peak-frequency of
each pulse (i.e. time-indexed vector TF spectrum) are calculated and
all pulses with similar parameters are grouped. According to the
characteristics of non-intrusive sensor and the frequency distribution
of PDs, the pulses of PD and interferences are separated. Finally the
PD signal and interferences are recovered via inverse TF transform.
The de-noised result of noisy PD data demonstrates that the
combination of frequency and time-frequency techniques can
discriminate PDs from interferences with various frequency
distributions.
Abstract: When cars are released from the factory, strut noises are very small and therefore it is difficult to perceive them. As the use time and travel distance increase, however, strut noises get larger so as to cause users much uneasiness. The noises generated at the field include engine noises and flow noises and therefore it is difficult to clearly discern the noises generated from struts. This study developed a test method which can reproduce field strut noises in the lab. Using the newly developed noise evaluation test, this study analyzed the effects that insulator performance degradation and failure can have on car noises. The study also confirmed that the insulator durability test by the simple back-and-forth motion cannot completely reflect the state of the parts failure in the field. Based on this, the study also confirmed that field noises can be reproduced through a durability test that considers heat aging.
Abstract: As the Internet continues to grow at a rapid pace as
the primary medium for communications and commerce and as
telecommunication networks and systems continue to expand their
global reach, digital information has become the most popular and
important information resource and our dependence upon the
underlying cyber infrastructure has been increasing significantly.
Unfortunately, as our dependency has grown, so has the threat to the
cyber infrastructure from spammers, attackers and criminal
enterprises. In this paper, we propose a new machine learning based
network intrusion detection framework for cyber security. The
detection process of the framework consists of two stages: model
construction and intrusion detection. In the model construction stage,
a semi-supervised machine learning algorithm is applied to a
collected set of network audit data to generate a profile of normal
network behavior and in the intrusion detection stage, input network
events are analyzed and compared with the patterns gathered in the
profile, and some of them are then flagged as anomalies should these
events are sufficiently far from the expected normal behavior. The
proposed framework is particularly applicable to the situations where
there is only a small amount of labeled network training data
available, which is very typical in real world network environments.
Abstract: Quality of Service (QoS) Routing aims to find path between source and destination satisfying the QoS requirements which efficiently using the network resources and underlying routing algorithm and to fmd low-cost paths that satisfy given QoS constraints. One of the key issues in providing end-to-end QoS guarantees in packet networks is determining feasible path that satisfies a number of QoS constraints. We present a Optimized Multi- Constrained Routing (OMCR) algorithm for the computation of constrained paths for QoS routing in computer networks. OMCR applies distance vector to construct a shortest path for each destination with reference to a given optimization metric, from which a set of feasible paths are derived at each node. OMCR is able to fmd feasible paths as well as optimize the utilization of network resources. OMCR operates with the hop-by-hop, connectionless routing model in IP Internet and does not create any loops while fmding the feasible paths. Nodes running OMCR not necessarily maintaining global view of network state such as topology, resource information and routing updates are sent only to neighboring nodes whereas its counterpart link-state routing method depend on complete network state for constrained path computation and that incurs excessive communication overhead.
Abstract: In digital signal processing it is important to
approximate multi-dimensional data by the method called rank
reduction, in which we reduce the rank of multi-dimensional data from
higher to lower. For 2-dimennsional data, singular value
decomposition (SVD) is one of the most known rank reduction
techniques. Additional, outer product expansion expanded from SVD
was proposed and implemented for multi-dimensional data, which has
been widely applied to image processing and pattern recognition.
However, the multi-dimensional outer product expansion has behavior
of great computation complex and has not orthogonally between the
expansion terms. Therefore we have proposed an alterative method,
Third-order Orthogonal Tensor Product Expansion short for 3-OTPE.
3-OTPE uses the power method instead of nonlinear optimization
method for decreasing at computing time. At the same time the group
of B. D. Lathauwer proposed Higher-Order SVD (HOSVD) that is
also developed with SVD extensions for multi-dimensional data.
3-OTPE and HOSVD are similarly on the rank reduction of
multi-dimensional data. Using these two methods we can obtain
computation results respectively, some ones are the same while some
ones are slight different. In this paper, we compare 3-OTPE to
HOSVD in accuracy of calculation and computing time of resolution,
and clarify the difference between these two methods.
Abstract: We demonstrate single-photon interference over 10 km using a plug and play system for quantum key distribution. The quality of the interferometer is measured by using the interferometer
visibility. The coding of the signal is based on the phase coding and the value of visibility is based on the interference effect, which result a number of count. The setup gives full control of polarization inside
the interferometer. The quality measurement of the interferometer is based on number of count per second and the system produces 94 % visibility in one of the detectors.
Abstract: Feature selection study is gaining importance due to its contribution to save classification cost in terms of time and computation load. In search of essential features, one of the methods to search the features is via the decision tree. Decision tree act as an intermediate feature space inducer in order to choose essential features. In decision tree-based feature selection, some studies used decision tree as a feature ranker with a direct threshold measure, while others remain the decision tree but utilized pruning condition that act as a threshold mechanism to choose features. This paper proposed threshold measure using Manhattan Hierarchical Cluster distance to be utilized in feature ranking in order to choose relevant features as part of the feature selection process. The result is promising, and this method can be improved in the future by including test cases of a higher number of attributes.
Abstract: XML has become a popular standard for information exchange via web. Each XML document can be presented as a rooted, ordered, labeled tree. The Node label shows the exact position of a node in the original document. Region and Dewey encoding are two famous methods of labeling trees. In this paper, we propose a new insert friendly labeling method named IFDewey based on recently proposed scheme, called Extended Dewey. In Extended Dewey many labels must be modified when a new node is inserted into the XML tree. Our method eliminates this problem by reserving even numbers for future insertion. Numbers generated by Extended Dewey may be even or odd. IFDewey modifies Extended Dewey so that only odd numbers are generated and even numbers can then be used for a much easier insertion of nodes.
Abstract: Personal computers draw non-sinusoidal current
with odd harmonics more significantly. Power Quality of
distribution networks is severely affected due to the flow of these
generated harmonics during the operation of electronic loads. In
this paper, mathematical modeling of odd harmonics in current like
3rd, 5th, 7th and 9th influencing the power quality has been presented.
Live signals have been captured with the help of power quality
analyzer for analysis purpose. The interesting feature is that Total
Harmonic Distortion (THD) in current decreases with the increase
of nonlinear loads has been verified theoretically. The results
obtained using mathematical expressions have been compared with
the practical results and exciting results have been found.
Abstract: We present a simplified equalization technique for a
π/4 differential quadrature phase shift keying ( π/4 -DQPSK) modulated
signal in a multipath fading environment. The proposed equalizer is
realized as a fractionally spaced adaptive decision feedback equalizer
(FS-ADFE), employing exponential step-size least mean square
(LMS) algorithm as the adaptation technique. The main advantage of
the scheme stems from the usage of exponential step-size LMS algorithm
in the equalizer, which achieves similar convergence behavior
as that of a recursive least squares (RLS) algorithm with significantly
reduced computational complexity. To investigate the finite-precision
performance of the proposed equalizer along with the π/4 -DQPSK
modem, the entire system is evaluated on a 16-bit fixed point digital
signal processor (DSP) environment. The proposed scheme is found
to be attractive even for those cases where equalization is to be
performed within a restricted number of training samples.
Abstract: With the enormous growth on the web, users get easily
lost in the rich hyper structure. Thus developing user friendly and
automated tools for providing relevant information without any
redundant links to the users to cater to their needs is the primary task
for the website owners. Most of the existing web mining algorithms
have concentrated on finding frequent patterns while neglecting the
less frequent one that are likely to contain the outlying data such as
noise, irrelevant and redundant data. This paper proposes new
algorithm for mining the web content by detecting the redundant
links from the web documents using set theoretical(classical
mathematics) such as subset, union, intersection etc,. Then the
redundant links is removed from the original web content to get the
required information by the user..
Abstract: The weight constrained shortest path problem
(WCSPP) is one of most several known basic problems in
combinatorial optimization. Because of its importance in many areas
of applications such as computer science, engineering and operations
research, many researchers have extensively studied the WCSPP.
This paper mainly concentrates on the reduction of total search space
for finding WCSP using some existing Genetic Algorithm (GA). For
this purpose, some controlled schemes of genetic operators are
adopted on list chromosome representation. This approach gives a
near optimum solution with smaller elapsed generation than classical
GA technique. From further analysis on the matter, a new
generalized schema theorem is also developed from the philosophy
of Holland-s theorem.
Abstract: This paper outlines the development of a learning retrieval agent. Task of this agent is to extract knowledge of the Active Semantic Network in respect to user-requests. Based on a reinforcement learning approach, the agent learns to interpret the user-s intention. Especially, the learning algorithm focuses on the retrieval of complex long distant relations. Increasing its learnt knowledge with every request-result-evaluation sequence, the agent enhances his capability in finding the intended information.