Abstract: In this paper, a Smart Home Service Robot, McBot II,
which performs mess-cleanup function etc. in house, is designed much
more optimally than other service robots. It is newly developed in
much more practical system than McBot I which we had developed
two years ago. One characteristic attribute of mobile platforms
equipped with a set of dependent wheels is their omni- directionality
and the ability to realize complex translational and rotational
trajectories for agile navigation in door. An accurate coordination of
steering angle and spinning rate of each wheel is necessary for a
consistent motion. This paper develops trajectory controller of
3-wheels omni-directional mobile robot using fuzzy azimuth estimator.
A specialized anthropomorphic robot manipulator which can be
attached to the housemaid robot McBot II, is developed in this paper.
This built-in type manipulator consists of both arms with 3 DOF
(Degree of Freedom) each and both hands with 3 DOF each. The
robotic arm is optimally designed to satisfy both the minimum
mechanical size and the maximum workspace. Minimum mass and
length are required for the built-in cooperated-arms system. But that
makes the workspace so small. This paper proposes optimal design
method to overcome the problem by using neck joint to move the arms
horizontally forward/backward and waist joint to move them
vertically up/down. The robotic hand, which has two fingers and a
thumb, is also optimally designed in task-based concept. Finally, the
good performance of the developed McBot II is confirmed through
live tests of the mess-cleanup task.
Abstract: The great challenge of the agricultural sector is to
produce more crop from less water, which can be achieved by
increasing crop water productivity. The modernization of the
irrigation systems offers a number of possibilities to expand the
economic productivity of water and improve the virtual water status.
The objective of the present study is to assess the global water
productivity (GWP) within the major irrigation command areas of
I.R. Iran. For this purpose, fourteen irrigation command areas where
located in different areas of Iran were selected. In order to calculate
the global water productivity of irrigation command areas, all data on
the delivered water to cropping pattern, cultivated area, crops water
requirement, and yield production rate during 2002-2006 were
gathered. In each of the command areas it seems that the cultivated
crops have a higher amount of virtual water and thus can be replaced
by crops with less virtual water. This is merely suggested due to crop
water consumption and at the time of replacing crops, economic
value as well as cultural and political factors must be considered. The
results indicated that the lowest GWP belongs to Mahyar and
Borkhar irrigation areas, 0.24 kg m-3, and the highest is that of the
Dez irrigation area, 0.81 kg m-3. The findings demonstrated that
water management in the two irrigation areas is just efficient. The
difference in the GWP of irrigation areas is due to variations in the
cropping pattern, amount of crop productions, in addition to the
effective factors in the water use efficiency in the irrigation areas.
Abstract: Transmission network expansion planning (TNEP) is an important component of power system planning that its task is to minimize the network construction and operational cost while satisfying the demand increasing, imposed technical and economic conditions. Up till now, various methods have been presented to solve the static transmission network expansion planning (STNEP) problem. But in all of these methods, the lines adequacy rate has not been studied after the planning horizon, i.e. when the expanded network misses its adequacy and needs to be expanded again. In this paper, in order to take transmission lines condition after expansion in to account from the line loading view point, the adequacy of transmission network is considered for solution of STNEP problem. To obtain optimal network arrangement, a decimal codification genetic algorithm (DCGA) is being used for minimizing the network construction and operational cost. The effectiveness of the proposed idea is tested on the Garver's six-bus network. The results evaluation reveals that the annual worth of network adequacy has a considerable effect on the network arrangement. In addition, the obtained network, based on the DCGA, has lower investment cost and higher adequacy rate. Thus, the network satisfies the requirements of delivering electric power more safely and reliably to load centers.
Abstract: IETF RFC 2002 originally introduced the wireless
Mobile-IP protocol to support portable IP addresses for mobile
devices that often change their network access points to the Internet.
The inefficiency of this protocol mainly within the handoff
management produces large end-to-end packet delays, during
registration process, and further degrades the system efficiency due to
packet losses between subnets. The criterion to initiate a simple and
fast full-duplex connection between the home agent and foreign
agent, to reduce the roaming duration, is a very important issue to be
considered by a work in this paper. State-transition Petri-Nets of the
modeling scenario-based CIA: communication inter-agents procedure
as an extension to the basic Mobile-IP registration process was
designed and manipulated. The heuristic of configuration file during
practical Setup session for registration parameters, on Cisco platform
Router-1760 using IOS 12.3 (15)T is created. Finally, stand-alone
performance simulations results from Simulink Matlab, within each
subnet and also between subnets, are illustrated for reporting better
end-to-end packet delays. Results verified the effectiveness of our
Mathcad analytical manipulation and experimental implementation. It
showed lower values of end-to-end packet delay for Mobile-IP using
CIA procedure. Furthermore, it reported packets flow between
subnets to improve packet losses between subnets.
Abstract: The modified Claus process is the major technology
for the recovery of elemental sulfur from hydrogen sulfide. The
chemical reactions that can occur in the reaction furnace are
numerous and many byproducts such as carbon disulfide and carbon
carbonyl sulfide are produced. These compounds can often contribute
from 20 to 50% of the pollutants and therefore, should be hydrolyzed
in the catalytic converter. The inlet temperature of the first catalytic
reactor should be maintained over than 250 °C, to hydrolyze COS
and CS2. In this paper, the various configurations for the first
converter reheating of sulfur recovery unit are investigated. As a
result, the performance of each method is presented for a typical
clause unit. The results show that the hot gas method seems to be
better than the other methods.
Abstract: In this paper we used data mining techniques to
identify outlier patients who are using large amount of drugs over a
long period of time. Any healthcare or health insurance system
should deal with the quantities of drugs utilized by chronic diseases
patients. In Kingdom of Bahrain, about 20% of health budget is spent
on medications. For the managers of healthcare systems, there is no
enough information about the ways of drug utilization by chronic
diseases patients, is there any misuse or is there outliers patients. In
this work, which has been done in cooperation with information
department in the Bahrain Defence Force hospital; we select the data
for Cardiac patients in the period starting from 1/1/2008 to
December 31/12/2008 to be the data for the model in this paper. We
used three techniques for finding the drug utilization for cardiac
patients. First we applied a clustering technique, followed by
measuring of clustering validity, and finally we applied a decision
tree as classification algorithm. The clustering results is divided into
three clusters according to the drug utilization, for 1603 patients, who
received 15,806 prescriptions during this period can be partitioned
into three groups, where 23 patients (2.59%) who received 1316
prescriptions (8.32%) are classified to be outliers. The classification
algorithm shows that the use of average drug utilization and the age,
and the gender of the patient can be considered to be the main
predictive factors in the induced model.
Abstract: Computer networks are essential part in computerbased
information systems. The performance of these networks has a
great influence on the whole information system. Measuring the
usability criteria and customers satisfaction on small computer
network is very important. In this article, an effective approach for
measuring the usability of business network in an information system
is introduced. The usability process for networking provides us with a
flexible and a cost-effective way to assess the usability of a network
and its products. In addition, the proposed approach can be used to
certify network product usability late in the development cycle.
Furthermore, it can be used to help in developing usable interfaces
very early in the cycle and to give a way to measure, track, and
improve usability. Moreover, a new approach for fast information
processing over computer networks is presented. The entire data are
collected together in a long vector and then tested as a one input
pattern. Proposed fast time delay neural networks (FTDNNs) use
cross correlation in the frequency domain between the tested data and
the input weights of neural networks. It is proved mathematically and
practically that the number of computation steps required for the
presented time delay neural networks is less than that needed by
conventional time delay neural networks (CTDNNs). Simulation
results using MATLAB confirm the theoretical computations.
Abstract: Information Retrieval has the objective of studying
models and the realization of systems allowing a user to find the
relevant documents adapted to his need of information. The
information search is a problem which remains difficult because the
difficulty in the representing and to treat the natural languages such
as polysemia. Intentional Structures promise to be a new paradigm to
extend the existing documents structures and to enhance the different
phases of documents process such as creation, editing, search and
retrieval. The intention recognition of the author-s of texts can reduce
the largeness of this problem. In this article, we present intentions
recognition system is based on a semi-automatic method of
extraction the intentional information starting from a corpus of text.
This system is also able to update the ontology of intentions for the
enrichment of the knowledge base containing all possible intentions
of a domain. This approach uses the construction of a semi-formal
ontology which considered as the conceptualization of the intentional
information contained in a text. An experiments on scientific
publications in the field of computer science was considered to
validate this approach.
Abstract: With getting older in the whole population, the
prevalence of stroke and its residual disability is getting higher and
higher recently in Taiwan. The functional electrical stimulation
cycling system (FESCS) is useful for hemiplegic patients. Because
that the muscle of stroke patients is under hybrid activation. The raw
electromyography (EMG) represents the residual muscle force of
stroke subject whereas the peak-to-peak of stimulus EMG indicates the
force enhancement benefiting from ES. It seems that EMG signals
could be used for a parameter of feedback control mechanism. So, we
design the feedback control protocol of FESCS, it includes
physiological signal recorder, FPGA biomedical module, DAC and
electrical stimulation circuit. Using the intensity of real-time EMG
signal obtained from patients, as a feedback control method for the
output voltage of FES-cycling system.
Abstract: In this study, the effects of biogas fuels on the performance of an annular micro gas turbine (MGT) were assessed experimentally and numerically. In the experiments, the proposed MGT system was operated successfully under each test condition; minimum composition to the fuel with the biogas was roughly 50% CH4 with 50% CO2. The power output was around 170W at 85,000 RPM as 90% CH4 with 10% CO2 was used and 70W at 65,000 RPM as 70% CH4 with 30% CO2 was used. When a critical limit of 60% CH4 was reached, the power output was extremely low. Furthermore, the theoretical Brayton cycle efficiency and electric efficiency of the MGT were calculated as 23% and 10%, respectively. Following the experiments, the measured data helped us identify the parameters of dynamic model in numerical simulation. Additionally, a numerical analysis of re-designed combustion chamber showed that the performance of MGT could be improved by raising the temperature at turbine inlet. This study presents a novel distributed power supply system that can utilize renewable biogas. The completed micro biogas power supply system is small, low cost, easy to maintain and suited to household use.
Abstract: The Algorithm 2 for a n-link manipulator movement amidst arbitrary unknown static obstacles for a case when a sensor system supplies information about local neighborhoods of different points in the configuration space is presented. The Algorithm 2 guarantees the reaching of a target position in a finite number of steps. The Algorithm 2 is reduced to a finite number of calls of a subroutine for planning a trajectory in the presence of known forbidden states. The polynomial approximation algorithm which is used as the subroutine is presented. The results of the Algorithm2 implementation are given.
Abstract: A prototype model of an emulsion separator was
designed and manufactured. Generally, it is a cylinder filled with
different fractal modules. The emulsion was fed into the reactor by a
peristaltic pump through an inlet placed at the boundary between the
two phases. For hydrodynamic design and sizing of the reactor the
assumptions of the theory of filtration were used and methods to
describe the separation process were developed. Based on this
methodology and using numerical methods and software of Autodesk
the process is simulated in different operating modes. The basic
hydrodynamic characteristics - speed and performance for different
types of fractal systems and decisions to optimize the design of the
reactor were also defined.
Abstract: This study systemizes processes and methods in
wooden furniture design that contains uniqueness in function and
aesthetics. The study was done by research and analysis for
designer-s consideration factors that affect function and production.
Therefore, the study result indicates that such factors are design
process (planning for design, product specifications, concept design,
product architecture, industrial design, production), design evaluation
as well as wooden furniture design dependent factors i.e. art (art
style; furniture history, form), functionality (the strength and
durability, area place, using), material (appropriate to function, wood
mechanical properties), joints, cost, safety, and social responsibility.
Specifically, all aforementioned factors affect good design. Resulting
from direct experience gained through user-s usage, the designer
must design the wooden furniture systemically and effectively. As a
result, this study selected dinning armchair as a case study with all
involving factors and all design process stated in this study.
Abstract: Recently, nanomaterials are developed in the form of nano-films, nano-crystals and nano-pores. Lanthanide phosphates as a material find extensive application as laser, ceramic, sensor, phosphor, and also in optoelectronics, medical and biological labels, solar cells and light sources. Among the different kinds of rare-earth orthophosphates, yttrium orthophosphate has been shown to be an efficient host lattice for rare earth activator ions, which have become a research focus because of their important role in the field of light display systems, lasers, and optoelectronic devices. It is in this context that the 4fn- « 4fn-1 5d transitions of rare earth in insulating materials, lying in the UV and VUV, are the aim of large number of studies .Though there has been a few reports on Eu3+, Nd3+, Pr3+,Er3+, Ce3+, Tm3+ doped YPO4. The 4fn- « 4fn-1 5d transitions of the rare earth dependent to the host-matrix, several matrices ions were used to study these transitions, in this work we are suggesting to study on a very specific class of inorganic material that are orthophosphate doped with rare earth ions. This study focused on the effect of Ce3+ concentration on the structural and optical properties of Ce3+ doped YPO4 yttrium orthophosphate with powder form prepared by the Sol Gel method.
Abstract: In recent years with the rapid development of Internet and the Web, more and more web applications have been deployed in many fields and organizations such as finance, military, and government. Together with that, hackers have found more subtle ways to attack web applications. According to international statistics, SQL Injection is one of the most popular vulnerabilities of web applications. The consequences of this type of attacks are quite dangerous, such as sensitive information could be stolen or authentication systems might be by-passed. To mitigate the situation, several techniques have been adopted. In this research, a security solution is proposed using Artificial Neural Network to protect web applications against this type of attacks. The solution has been experimented on sample datasets and has given promising result. The solution has also been developed in a prototypic web application firewall called ANNbWAF.
Abstract: Computation of facility location problem for every
location in the country is not easy simultaneously. Solving the
problem is described by using cluster computing. A technique is to
design parallel algorithm by using local search with single swap
method in order to solve that problem on clusters. Parallel
implementation is done by the use of portable parallel programming,
Message Passing Interface (MPI), on Microsoft Windows Compute
Cluster. In this paper, it presents the algorithm that used local search
with single swap method and implementation of the system of a
facility to be opened by using MPI on cluster. If large datasets are
considered, the process of calculating a reasonable cost for a facility
becomes time consuming. The result shows parallel computation of
facility location problem on cluster speedups and scales well as
problem size increases.
Abstract: Urbanization and related anthropogenic modifications
cause extent of habitat fragmentation and directly lead to decline of
local biodiversity. Conservation biologists advocate corridor creation
as one approach to rescue biodiversity. Here we examine the utility of
roads as corridors in preserving plant diversity by investigating
roadside vegetation in Yellow River Delta (YRD), China. We
examined the spatio-temporal distribution pattern of plant species
richness, diversity and composition along roadside. The results
suggest that roads, as dispersal conduits, increase occurrence
probability of new settlers to a new area, meanwhile, roads accumulate
the greater propagule pressure and favourable survival condition
during operation phase. As a result, more species, including native and
alien plants, non- halophyte and halophyte species, threatened and
cosmopolitic species, were found prosperous at roadside. Roadside
may be a refuge for more species, and the pattern of vegetation
distribution is affected by road age and the distance from road verge.
Abstract: Cognitive Science appeared about 40 years ago,
subsequent to the challenge of the Artificial Intelligence, as common
territory for several scientific disciplines such as: IT, mathematics,
psychology, neurology, philosophy, sociology, and linguistics. The
new born science was justified by the complexity of the problems
related to the human knowledge on one hand, and on the other by the
fact that none of the above mentioned sciences could explain alone
the mental phenomena. Based on the data supplied by the
experimental sciences such as psychology or neurology, models of
the human mind operation are built in the cognition science. These
models are implemented in computer programs and/or electronic
circuits (specific to the artificial intelligence) – cognitive systems –
whose competences and performances are compared to the human
ones, leading to the psychology and neurology data reinterpretation,
respectively to the construction of new models. During these
processes if psychology provides the experimental basis, philosophy
and mathematics provides the abstraction level utterly necessary for
the intermission of the mentioned sciences.
The ongoing general problematic of the cognitive approach
provides two important types of approach: the computational one,
starting from the idea that the mental phenomenon can be reduced to
1 and 0 type calculus operations, and the connection one that
considers the thinking products as being a result of the interaction
between all the composing (included) systems. In the field of
psychology measurements in the computational register use classical
inquiries and psychometrical tests, generally based on calculus
methods. Deeming things from both sides that are representing the
cognitive science, we can notice a gap in psychological product
measurement possibilities, regarded from the connectionist
perspective, that requires the unitary understanding of the quality –
quantity whole. In such approach measurement by calculus proves to
be inefficient. Our researches, deployed for longer than 20 years,
lead to the conclusion that measuring by forms properly fits to the
connectionism laws and principles.
Abstract: Robots- visual perception is a field that is gaining
increasing attention from researchers. This is partly due to emerging
trends in the commercial availability of 3D scanning systems or
devices that produce a high information accuracy level for a variety of
applications. In the history of mining, the mortality rate of mine workers
has been alarming and robots exhibit a great deal of potentials to
tackle safety issues in mines. However, an effective vision system
is crucial to safe autonomous navigation in underground terrains.
This work investigates robots- perception in underground terrains
(mines and tunnels) using statistical region merging (SRM) model.
SRM reconstructs the main structural components of an imagery
by a simple but effective statistical analysis. An investigation is
conducted on different regions of the mine, such as the shaft, stope
and gallery, using publicly available mine frames, with a stream of
locally captured mine images. An investigation is also conducted on a
stream of underground tunnel image frames, using the XBOX Kinect
3D sensors. The Kinect sensors produce streams of red, green and
blue (RGB) and depth images of 640 x 480 resolution at 30 frames per
second. Integrating the depth information to drivability gives a strong
cue to the analysis, which detects 3D results augmenting drivable and
non-drivable regions in 2D. The results of the 2D and 3D experiment
with different terrains, mines and tunnels, together with the qualitative
and quantitative evaluation, reveal that a good drivable region can be
detected in dynamic underground terrains.
Abstract: The ever-growing usage of aspect-oriented
development methodology in the field of software engineering
requires tool support for both research environments and industry. So
far, tool support for many activities in aspect-oriented software
development has been proposed, to automate and facilitate their
development. For instance, the AJaTS provides a transformation
system to support aspect-oriented development and refactoring. In
particular, it is well established that the abstract interpretation of
programs, in any paradigm, pursued in static analysis is best served
by a high-level programs representation, such as Control Flow Graph
(CFG). This is why such analysis can more easily locate common
programmatic idioms for which helpful transformation are already
known as well as, association between the input program and
intermediate representation can be more closely maintained.
However, although the current researches define the good concepts
and foundations, to some extent, for control flow analysis of aspectoriented
programs but they do not provide a concrete tool that can
solely construct the CFG of these programs. Furthermore, most of
these works focus on addressing the other issues regarding Aspect-
Oriented Software Development (AOSD) such as testing or data flow
analysis rather than CFG itself. Therefore, this study is dedicated to
build an aspect-oriented control flow graph construction tool called
AJcFgraph Builder. The given tool can be applied in many software
engineering tasks in the context of AOSD such as, software testing,
software metrics, and so forth.