Abstract: An approach for experimental measurement of the
dynamic characteristics of linear electromagnet actuators is
presented. It uses accelerometer sensor to register the armature
acceleration. The velocity and displacement of the moving parts can
be obtained by integration of the acceleration results. The armature
movement of permanent magnet linear actuator is acquired using this
technique. The results are analyzed and the performance of the
supposed approach is compared with the most commonly used
experimental setup where the displacement of the armature vs. time
is measured instead of its acceleration.
Abstract: Human heart valves diseased by congenital heart
defects, rheumatic fever, bacterial infection, cancer may cause stenosis
or insufficiency in the valves. Treatment may be with medication but
often involves valve repair or replacement (insertion of an artificial
heart valve). Bileaflet mechanical heart valves (BMHVs) are widely
implanted to replace the diseased heart valves, but still suffer from
complications such as hemolysis, platelet activation, tissue
overgrowth and device failure. These complications are closely related
to both flow characteristics through the valves and leaflet dynamics. In
this study, the physiological flow interacting with the moving leaflets
in a bileaflet mechanical heart valve (BMHV) is simulated with a
strongly coupled implicit fluid-structure interaction (FSI) method
which is newly organized based on the Arbitrary-Lagrangian-Eulerian
(ALE) approach and the dynamic mesh method (remeshing) of
FLUENT. The simulated results are in good agreement with previous
experimental studies. This study shows the applicability of the present
FSI model to the complicated physics interacting between fluid flow
and moving boundary.
Abstract: Composite pins of rubber dust collected from tyre
retreading centres of trucks, cars and buses etc.and epoxy with
weight percentages of 10. 15, and 20 % of rubber (weight fractions of
9, 13 and 17 % respectively) have been prepared in house with the
help of a split wooden mould. The pins were tested in a pin-on-disc
wear monitor to determine the co-efficient of friction and weight
losses with varying speeds, loads and time. The wear volume and
wear rates have also been found out for all these three specimens.. It
is observed that all the specimens have exhibited very low coefficient
of friction and low wear rates under dry sliding condition. Out of the
above three samples tested, the specimen with 10 % rubber dust by
weight has shown lowest wear rates. However a peculiar result i.e
decreasing trend has been obtained with 20% reinforcement of rubber
in epoxy while rubbed against steel at varying speeds. This might
have occurred due to high surface finish of the disc and formation of
a thin transfer layer from the composite
Abstract: This paper presents a new problem solving approach
that is able to generate optimal policy solution for finite-state
stochastic sequential decision-making problems with high data
efficiency. The proposed algorithm iteratively builds and improves
an approximate Markov Decision Process (MDP) model along with
cost-to-go value approximates by generating finite length trajectories
through the state-space. The approach creates a synergy between an
approximate evolving model and approximate cost-to-go values to
produce a sequence of improving policies finally converging to the
optimal policy through an intelligent and structured search of the
policy space. The approach modifies the policy update step of the
policy iteration so as to result in a speedy and stable convergence to
the optimal policy. We apply the algorithm to a non-holonomic
mobile robot control problem and compare its performance with
other Reinforcement Learning (RL) approaches, e.g., a) Q-learning,
b) Watkins Q(λ), c) SARSA(λ).
Abstract: The Application of e-health solutions has brought superb advancements in the health care industry. E-health solutions have already been embraced in the industrialized countries. In an effort to catch up with the growth, the developing countries have strived to revolutionize the healthcare industry by use of Information technology in different ways. Based on a technology assessment carried out in Kenya – one of the developing countries – and using multiple case studies in Nyanza Province, this work focuses on an investigation on how five rural hospitals are adapting to the technology shift. The issues examined include the ICT infrastructure and e-health technologies in place, the knowledge of participants in terms of benefits gained through the use of ICT and the challenges posing barriers to the use of ICT technologies in these hospitals. The results reveal that the ICT infrastructure in place is inadequate for e-health implementations as a result to various challenges that exist. Consequently, suggestions on how to tackle the various challenges have been addressed in this paper.
Abstract: Conventional WBL is effective for meaningful student, because rote student learn by repeating without thinking or trying to understand. It is impossible to have full benefit from conventional WBL. Understanding of rote student-s intention and what influences it becomes important. Poorly designed user interface will discourage rote student-s cultivation and intention to use WBL. Thus, user interface design is an important factor especially when WBL is used as comprehensive replacement of conventional teaching. This research proposes the influencing factors that can enhance student-s intention to use the system. The enhanced TAM is used for evaluating the proposed factors. The research result points out that factors influencing rote student-s intention are Perceived Usefulness of Homepage Content Structure, Perceived User Friendly Interface, Perceived Hedonic Component, and Perceived (homepage) Visual Attractiveness.
Abstract: Use of a sliding joint is an effective method to
decrease the stress in foundation structure where there is a horizontal
deformation of subsoil (areas afflicted with underground mining) or
horizontal deformation of a foundation structure (pre-stressed
foundations, creep, shrinkage, temperature deformation). A
convenient material for a sliding joint is a bitumen asphalt belt.
Experiments for different types of bitumen belts were undertaken at
the Faculty of Civil Engineering - VSB Technical University of
Ostrava in 2008. This year an extension of the 2008 experiments is in
progress and the shear resistance of a slide joint is being tested as a
function of temperature in a temperature controlled room. In this
paper experimental results of temperature dependant shear resistance
are presented. The result of the experiments should be the sliding
joint shear resistance as a function of deformation velocity and
temperature. This relationship is used for numerical analysis of
stress/strain relation between foundation structure and subsoil. Using
a rheological slide joint could lead to a decrease of the reinforcement
amount, and contribute to higher reliability of foundation structure
and thus enable design of more durable and sustainable building
structures.
Abstract: Anti-money laundering is commonly recognized as a
set of procedures, laws or regulations designed to reduce the practice
of generating income through illegal actions. In Malaysia, the
government and law enforcement agencies have stepped up their
capacities and efforts to curb money laundering since 2001. One of
these measures was the enactment of the Anti-Money Laundering
Act (AMLA) in 2001. The implementation costs on anti-money
laundering requirements (AMLR) can be burdensome to those who
are involved in enforcing them. The objective of this paper is to
explore the perceived effectiveness of AMLR from the enforcement
agencies- perspective. This is a preliminary study whose findings
will help to give direction for further AML research in Malaysia. In
addition, the results of this study provide empirical evidences on the
perceived effectiveness of AMLR prior to further investigations on
barriers and improvements of the implementation of the anti-money
laundering regime in Malaysia.
Abstract: The motion planning technique described in this paper has been developed to eliminate or reduce the residual vibrations of belt-driven rotary platforms, while maintaining unchanged the motion time and the total angular displacement of the platform. The proposed approach is based on a suitable choice of the motion command given to the servomotor that drives the mechanical device; this command is defined by some numerical coefficients which determine the shape of the displacement, velocity and acceleration profiles. Using a numerical optimization technique, these coefficients can be changed without altering the continuity conditions imposed on the displacement and its time derivatives at the initial and final time instants. The proposed technique can be easily and quickly implemented on an actual device, since it requires only a simple modification of the motion command profile mapped in the memory of the electronic motion controller.
Abstract: Adapting wireless devices to communicate within grid
networks empowers us by providing range of possibilities.. These
devices create a mechanism for consumers and publishers to create
modern networks with or without peer device utilization. Emerging
mobile networks creates new challenges in the areas of reliability,
security, and adaptability. In this paper, we propose a system
encompassing mobility management using AAA context transfer for
mobile grid networks. This system ultimately results in seamless task
processing and reduced packet loss, communication delays,
bandwidth, and errors.
Abstract: The aim of the current work is to present a comparison among three popular optimization methods in the inverse elastostatics problem (IESP) of flaw detection within a solid. In more details, the performance of a simulated annealing, a Hooke & Jeeves and a sequential quadratic programming algorithm was studied in the test case of one circular flaw in a plate solved by both the boundary element (BEM) and the finite element method (FEM). The proposed optimization methods use a cost function that utilizes the displacements of the static response. The methods were ranked according to the required number of iterations to converge and to their ability to locate the global optimum. Hence, a clear impression regarding the performance of the aforementioned algorithms in flaw identification problems was obtained. Furthermore, the coupling of BEM or FEM with these optimization methods was investigated in order to track differences in their performance.
Abstract: This work was conducted to improve the level of
resistant starch (RS) in a rice noodle using unripe banana flour and to
investigate the effect of substitution of unripe banana flour for rice
flour on the physical properties of rice noodle. In order to prepare
rice noodles, the unripe banana flour were replaced the rice flour
with different degrees of substitutions including 0, 20, 40, 60, 80, and
100%. The results indicated that substitution of unripe banana flour
was significantly affected the viscosity properties of noodle flour,
color, cooking loss, RS and total starch content of noodle. It was
found that the noodle prepared from 100% unripe banana indicated
the greatest changes on the viscosity properties and color profiles. It
also showed the highest values of cooking loss (2.53%), tensile
strength (129.03%), and RS content (13.15%).
Abstract: This paper analyzes the effect of a single uniform accounting rule on reporting quality by investigating the influence of IFRS on earnings management. This paper examines whether earnings management is reduced after IFRS adoption through the use of “loss avoidance thresholds”, a method that has been verified in earlier studies. This paper concentrates on two European countries: one that represents the continental code law tradition with weak protection of investors (France) and one that represents the Anglo-American common law tradition, which typically implies a strong enforcement system (the United Kingdom).
The research investigates a sample of 526 companies (6822 firm-year observations) during the years 2000 – 2013. The results are different for the two jurisdictions. This study demonstrates that a single set of accounting standards contributes to better reporting quality and reduces the pervasiveness of earnings management in France. In contrast, there is no evidence that a reduction in earnings management followed the implementation of IFRS in the United Kingdom. Due to the fact that IFRS benefit France but not the United Kingdom, other political and economic factors, such legal system or capital market strength, must play a significant role in influencing the comparability and transparency cross-border companies’ financial statements. Overall, the result suggests that IFRS moderately contribute to the accounting quality of reported financial statements and bring benefit for stakeholders, though the role played by other economic factors cannot be discounted.
Abstract: Service life of existing reinforced concrete (RC)
structures in coastal towns of Sabah has been affected very much.
Concrete crack, spalling of concrete cover and reinforcement rusting
of RC buildings are seen even within 5 years of construction in
Sabah. Hence, in this study a new mix design of concrete grout was
developed using locally available materials and investigated under
two curing conditions and workability, compressive strength,
Accelerated Mortar Bar Test (AMBT), water absorption, volume of
permeable voids (VPV), Sorptivity and 90-days salt ponding test
were conducted. The compressive strength of concrete grout at the
age 90 days was found to be 44.49 N/mm2 under water curing. It was
observed that the percentage of mortar bar length change was below
1% for developed concrete grout. The water absorption of the
concrete grout was in between the range of 0.88 % to 3.60 % under
two different curing up to the age 90 days. It was also observed that
the VPV of concrete was in the range of 0 % to 9.75 and 2.44% to
13.05% under water curing and site curing respectively. It was found
that the Sorptivity of the concrete grout under water curing at the age
of 28 days is 0.211mm/√min and at the age 90 day are 0.067
mm/√min. The chloride content decreased greatly, 90% after a depth
of 15 mm. It was noticed that the site cured samples showed higher
chloride contents near surface compared to water cured samples.
This investigation suggested that the developed mix design of
concrete grout using locally available construction materials can be
used for crack repairing of existing RC structures in Sabah.
Abstract: Using electrical machine in conventional vehicles, also called hybrid vehicles, has become a promising control scheme that enables some manners for fuel economy and driver assist for better stability. In this paper, vehicle stability control, fuel economy and Driving/Regeneration braking for a 4WD hybrid vehicle is investigated by using an electrical machine on each non-driven wheels. In front wheels driven vehicles, fuel economy and regenerative braking can be obtained by summing torques applied on rear wheels. On the other hand, unequal torques applied to rear wheels provides enhanced safety and path correction in steering. In this paper, a model with fourteen degrees of freedom is considered for vehicle body, tires and, suspension systems. Thereafter, powertrain subsystems are modeled. Considering an electrical machine on each rear wheel, a fuzzy controller is designed for each driving, braking, and stability conditions. Another fuzzy controller recognizes the vehicle requirements between the driving/regeneration and stability modes. Intelligent vehicle control to multi objective operation and forward simulation are the paper advantages. For reaching to these aims, power management control and yaw moment control will be done by three fuzzy controllers. Also, the above mentioned goals are weighted by another fuzzy sub-controller base on vehicle dynamic. Finally, Simulations performed in MATLAB/SIMULINK environment show that the proposed structure can enhance the vehicle performance in different modes effectively.
Abstract: Generally, in order to create 3D sound using binaural
systems, we use head related transfer functions (HRTF) including the
information of sounds which is arrived to our ears. But it can decline
some three-dimensional effects in the area of a cone of confusion
between front and back directions, because of the characteristics of
HRTF.
In this paper, we propose a new method to use psychoacoustics
theory that reduces the confusion of sound image localization. In the
method, HRTF spectrum characteristic is enhanced by using the
energy ratio of the bark band. Informal listening tests show that the
proposed method improves the front-back sound localization
characteristics much better than the conventional methods
Abstract: The significance of psychology in studying politics
is embedded in philosophical issues as well as behavioural
pursuits. For the former is often associated with Sigmund Freud
and his followers. The latter is inspired by the writings of Harold
Lasswell. Political psychology or psychopolitics has its own
impression on political thought ever since it deciphers the concept
of human nature and political propaganda. More importantly,
psychoanalysis views political thought as a textual content which
needs to explore the latent from the manifest content. In other
words, it reads the text symptomatically and interprets the hidden
truth. This paper explains the paradigm of dream interpretation
applied by Freud. The dream work is a process which has four
successive activities: condensation, displacement, representation
and secondary revision. The texts dealing with political though can
also be interpreted on these principles. Freud's method of dream
interpretation draws its source after the hermeneutic model of
philological research. It provides theoretical perspective and
technical rules for the interpretation of symbolic structures. The
task of interpretation remains a discovery of equivalence of
symbols and actions through perpetual analogies. Psychoanalysis
can help in studying political thought in two ways: to study the text
distortion, Freud's dream interpretation is used as a paradigm
exploring the latent text from its manifest text; and to apply Freud's
psychoanalytic concepts and theories ranging from individual mind
to civilization, religion, war and politics.
Abstract: In This paper, the behavior of eccentric braced frame
(EBF) is studied with replacing friction damper (FD) in confluence of these braces, in 5 and 10-storey steel frames. For FD system, the main step is to determine the slip load. For this reason, the performance indexes include roof displacement, base shear, dissipated energy and relative performance should be investigated. In
nonlinear dynamic analysis, the response of structure to three
earthquake records has been obtained and the values of roof
displacement, base shear and column axial force for FD and EBF
frames have been compared. The results demonstrate that use of the FD in frames, in comparison with the EBF, substantially reduces the roof displacement, column axial force and base shear. The obtained results show suitable performance of FD in higher storey structure in
comparison with the EBF.
Abstract: This study investigates the investors- behavioral
reaction to the investment rating change announcements from the
views of behavioral finance. The empirical results indicate that
self-interest does affect the intention of securities firms to release
investment ratings for individual stocks. In addition, behavioral
pitfalls are also found in the response of retail investors to investment
rating change announcements.
Abstract: The very nonlinear nature of the generator and system
behaviour following a severe disturbance precludes the use of
classical linear control technique. In this paper, a new approach of
nonlinear control is proposed for transient and steady state stability
analysis of a synchronous generator. The control law of the generator
excitation is derived from the basis of Lyapunov stability criterion.
The overall stability of the system is shown using Lyapunov
technique. The application of the proposed controller to simulated
generator excitation control under a large sudden fault and wide
range of operating conditions demonstrates that the new control
strategy is superior to conventional automatic voltage regulator
(AVR), and show very promising results.