Abstract: The paper presents a one-dimensional transient
mathematical model of thermal oil-water two-phase emulsion flows
in pipes. The set of the mass, momentum and enthalpy conservation
equations for the continuous fluid and droplet phases are solved. Two
friction correlations for the continuous fluid phase to wall friction are
accounted for in the model and tested. The aerodynamic drag force
between the continuous fluid phase and droplets is modeled, too. The
density and viscosity of both phases are assumed to be constant due
to adiabatic experimental conditions. The proposed mathematical
model is validated on the experimental measurements of oil-water
emulsion flows in horizontal pipe [1,2]. Numerical analysis on
single- and two-phase oil-water flows in a pipe is presented in the
paper. The continuous oil flow having water droplets is simulated.
Predictions, which are performed by using the presented model, show
excellent agreement with the experimental data if the water fraction is
equal or less than 10%. Disagreement between simulations and
measurements is increased if the water fraction is larger than 10%.
Abstract: This paper investigates experimental and numerical study of the airflow characteristics for vortex, round and square ceiling diffusers and its effect on the thermal comfort in a ventilated room. Three different thermal comfort criteria namely; Mean Age of the Air (MAA), ventilation effectiveness (E), and Effective Draft Temperature (EDT) have been used to predict the thermal comfort zone inside the room. In experimental work, a sub-scale room is set-up to measure the temperature field in the room. In numerical analysis, unstructured grids have been used to discretize the numerical domain. Conservation equations are solved using FLUENT commercial flow solver. The code is validated by comparing the numerical results obtained from three different turbulence models with the available experimental data. The comparison between the various numerical models shows that the standard k-ε turbulence model can be used to simulate these cases successfully. After validation of the code, effect of supply air velocity on the flow and thermal field could be investigated and hence the thermal comfort. The results show that the pressure coefficient created by the square diffuser is 1.5 times greater than that created by the vortex diffuser. The velocity decay coefficient is nearly the same for square and round diffusers and is 2.6 times greater than that for the vortex diffuser.
Abstract: Recently, a growing interest has emerged on the
development of new and efficient energy sources, due to the inevitable extinction of the nonrenewable energy reserves. One of
these alternative sources which has a great potential and sustainability to meet up the energy demand is biomass energy. This
significant energy source can be utilized with various energy
conversion technologies, one of which is biomass gasification in
supercritical water.
Water, being the most important solvent in nature, has very important characteristics as a reaction solvent under supercritical
circumstances. At temperatures above its critical point (374.8oC and
22.1 MPa), water becomes more acidic and its diffusivity increases.
Working with water at high temperatures increases the thermal
reaction rate, which in consequence leads to a better dissolving of the
organic matters and a fast reaction with oxygen. Hence, supercritical water offers a control mechanism depending on solubility, excellent
transport properties based on its high diffusion ability and new reaction possibilities for hydrolysis or oxidation.
In this study the gasification of a real biomass, namely olive mill
wastewater (OMW), in supercritical water is investigated with the
use of Pt/Al2O3 and Ni/Al2O3 catalysts. OMW is a by-product
obtained during olive oil production, which has a complex nature
characterized by a high content of organic compounds and
polyphenols. These properties impose OMW a significant pollution
potential, but at the same time, the high content of organics makes
OMW a desirable biomass candidate for energy production.
All of the catalytic gasification experiments were made with five
different reaction temperatures (400, 450, 500, 550 and 600°C),
under a constant pressure of 25 MPa. For the experiments conducted
with Ni/Al2O3 catalyst, the effect of five reaction times (30, 60, 90,
120 and 150 s) was investigated. However, procuring that similar
gasification efficiencies could be obtained at shorter times, the experiments were made by using different reaction times (10, 15, 20,
25 and 30 s) for the case of Pt/Al2O3 catalyst. Through these experiments, the effects of temperature, time and catalyst type on the
gasification yields and treatment efficiencies were investigated.
Abstract: In this work Artificial Intelligence (AI) techniques like Fuzzy logic, Genetic Algorithms and Particle Swarm Optimization have been used to improve the performance of the Automatic Generation Control (AGC) system. Instead of applying Genetic Algorithms and Particle swarm optimization independently for optimizing the parameters of the conventional AGC with PI controller, an intelligent tuned Fuzzy logic controller (acting as the secondary controller in the AGC system) has been designed. The controller gives an improved dynamic performance for both hydrothermal and thermal-thermal power systems under a variety of operating conditions.
Abstract: In this paper are illustrated the principal aspects
connected with the numerical evaluation of thermal stress induced by high gradient temperature in the concrete beam. The reinforced concrete beam has many advantages over steel
beam, such as high resistance to high temperature, high resistance to thermal shock, Better resistance to fatigue and buckling, strong
resistance against, fire, explosion, etc.
The main drawback of the reinforced concrete beam is its poor resistance to tensile stresses. In order to investigate the thermal
induced tensile stresses, a numerical model of a transient thermal
analysis is presented for the evaluation of thermo-mechanical
response of concrete beam to the high temperature, taking into account the temperature dependence of the thermo physical properties of the concrete like thermal conductivity and specific heat.
Abstract: The present study conducted experimental investigation on combustion and emission characteristics of compression ignition engine using diesel as pilot fuel and methane, hydrogen and methane/hydrogen mixture as gaseous fuels at 1800 rev min-1. The effect of gaseous fuel on peak cylinder pressure and heat release is modest at low to medium loads. At high load, the high combustion temperature and high quantity of pilot fuel contribute to better combustion efficiency for all kinds of gaseous fuels and increases the peak cylinder pressure. Enrichment of hydrogen in methane gradually increases the peak cylinder pressure. The brake thermal efficiency increases with higher hydrogen fraction at lower loads. Hydrogen addition in methane contributed to a proportional reduction of CO/CO2/HC emission without penalty of NOx. For particulate emission, methane and hydrogen, could both suppress the particle emission. 30% hydrogen fraction in methane is observed to be best in reducing the particulate emission.
Abstract: Efficient utilization of existing water is a pressing
need for Pakistan. Due to rising population, reduction in present
storage capacity and poor delivery efficiency of 30 to 40% from
canal. A study to evaluate an irrigation system in the cotton-wheat
zone of Pakistan, after the watercourse lining was conducted. The
study is made on the basis of cropping pattern and salinity to evaluate
the system. This study employed an index-based approach of using
Geographic information system with field data. The satellite images
of different years were use to examine the effective area. Several
combinations of the ratio of signals received in different spectral
bands were used for development of this index. Near Infrared and
Thermal IR spectral bands proved to be most effective as this
combination helped easy detection of salt affected area and cropping
pattern of the study area. Result showed that 9.97% area under
salinity in 1992, 9.17% in 2000 and it left 2.29% in year 2005.
Similarly in 1992, 45% area is under vegetation it improves to 56%
and 65% in 2000 and 2005 respectively. On the basis of these results
evaluation is done 30% performance is increase after the watercourse
improvement.
Abstract: Typically thermal power plants are located near to
surface coal mines that produce huge amount of fly ash as a waste
byproduct. Disposal of fly ash causes significant economic and
environmental problems. Now-a-days, research is going on for bulk
utilization of fly ash. In order to increase its percentage utilization, an
investigation was carried out to evaluate its potential for haul road
construction. This paper presents the laboratory California bearing
ratio (CBR) tests and evaluates the effect of lime on CBR behavior of
fly ash - mine overburden mixes. Tests were performed with different
percentages of lime (2%, 3%, 6%, and 9%). The results show that the
increase in bearing ratio of fly ash-overburden mixes was achieved
by lime treatment. Scanning electron microscopy (SEM) analyses
were conducted on 28 days cured specimens. The SEM study showed
that the bearing ratio development is related to the microstructural
development.
Abstract: This study presents the numerical simulation of
optimum pin-fin heat sink with air impinging cooling by using
Taguchi method. 9 L ( 4 3 ) orthogonal array is selected as a plan for
the four design-parameters with three levels. The governing
equations are discretized by using the
control-volume-based-finite-difference method with a power-law
scheme on the non-uniform staggered grid. We solved the coupling of
the velocity and the pressure terms of momentum equations using
SIMPLEC algorithm. We employ the k −ε two-equations
turbulence model to describe the turbulent behavior. The parameters
studied include fin height H (35mm-45mm), inter-fin spacing a , b ,
and c (2 mm-6.4 mm), and Reynolds number ( Re = 10000- 25000).
The objective of this study is to examine the effects of the fin
spacings and fin height on the thermal resistance and to find the
optimum group by using the Taguchi method. We found that the fin
spacings from the center to the edge of the heat sink gradually
extended, and the longer the fin’s height the better the results. The
optimum group is 3 1 2 3 H a b c . In addition, the effects of parameters are
ranked by importance as a , H , c , and b .
Abstract: Vernacular building is considered as sustainable in
energy consumption and environment and its thermal performance is
more and more concerned by researchers. This paper investigates the
thermal property of the vernacular building in Lhasa by theoretical
analysis on the aspects of building form, envelope and materials etc.
The values of thermal resistance and thermal capacity of the envelope
are calculated and compared with the current China building code and
modern building case. And it is concluded that Lhasa vernacular
building meets the current China building code of thermal standards
and have better performance in some aspects, which is achieved by
various passive means with close response to local climate conditions.
Abstract: Thermo-chemical treatment (TCT) such as pyrolysis
is getting recognized as a valid route for (i) materials and valuable
products and petrochemicals recovery; (ii) waste recycling; and (iii)
elemental characterization. Pyrolysis is also receiving renewed
attention for its operational, economical and environmental
advantages. In this study, samples of polyethylene terephthalate
(PET) and polystyrene (PS) were pyrolysed in a microthermobalance
reactor (using a thermogravimetric-TGA setup). Both
polymers were prepared and conditioned prior to experimentation.
The main objective was to determine the kinetic parameters of the
depolymerization reactions that occur within the thermal degradation
process. Overall kinetic rate constants (ko) and activation energies
(Eo) were determined using the general kinetics theory (GKT)
method previously used by a number of authors. Fitted correlations
were found and validated using the GKT, errors were within ± 5%.
This study represents a fundamental step to pave the way towards the
development of scaling relationship for the investigation of larger
scale reactors relevant to industry.
Abstract: In this paper, the bond strength of thermal spray
coatings in high speed shafts has been studied. The metallurgical and
mechanical studies has been made on the coated samples and shaft
using optical microscopy, scanning electron microscopy (SEM).
Abstract: The present paper develops and validates a numerical procedure for the calculation of turbulent combustive flow in converging and diverging ducts and throuh simulation of the heat transfer processes, the amount of production and spread of Nox pollutant has been measured. A marching integration solution procedure employing the TDMA is used to solve the discretized equations. The turbulence model is the Prandtl Mixing Length method. Modeling the combustion process is done by the use of Arrhenius and Eddy Dissipation method. Thermal mechanism has been utilized for modeling the process of forming the nitrogen oxides. Finite difference method and Genmix numerical code are used for numerical solution of equations. Our results indicate the important influence of the limiting diverging angle of diffuser on the coefficient of recovering of pressure. Moreover, due to the intense dependence of Nox pollutant to the maximum temperature in the domain with this feature, the Nox pollutant amount is also in maximum level.
Abstract: Heating is inevitable in any bearing operation. This
leads to not only the thinning of the lubricant but also could lead to a
thermal deformation of the bearing. The present work is an attempt to
analyze the influence of thermal deformation on the thermohydrodynamic
lubrication of infinitely long tilted pad slider rough
bearings. As a consequence of heating the slider is deformed and is
assumed to take a parabolic shape. Also the asperities expand leading
to smaller effective film thickness. Two different types of surface
roughness are considered: longitudinal roughness and transverse
roughness. Christensen-s stochastic approach is used to derive the
Reynolds-type equations. Density and viscosity are considered to be
temperature dependent. The modified Reynolds equation, momentum
equation, continuity equation and energy equation are decoupled and
solved using finite difference method to yield various bearing
characteristics. From the numerical simulations it is observed that the
performance of the bearing is significantly affected by the thermal
distortion of the slider and asperities and even the parallel sliders
seem to carry some load.
Abstract: A CFD study on heat flux reduction in hypersonic flow with opposing jet has been conducted. Flowfield parameters, reattachment point position, surface pressure distributions and heat flux distributions are obtained and validated with experiments. The physical mechanism of heat reduction has been analyzed. When the opposing jet blows, the freestream is blocked off, flows to the edges and not interacts with the surface to form aerodynamic heating. At the same time, the jet flows back to form cool recirculation region, which reduces the difference in temperature between the surface and the nearby gas, and then reduces the heat flux. As the pressure ratio increases, the interface between jet and freestream is gradually pushed away from the surface. Larger the total pressure ratio is, lower the heat flux is. To study the effect of the intensity of opposing jet more reasonably, a new parameter RPA has been introduced by combining the flux and the total pressure ratio. The study shows that the same shock wave position and total heat load can be obtained with the same RPA with different fluxes and the total pressures, which means the new parameter could stand for the intensity of opposing jet and could be used to analyze the influence of opposing jet on flow field and aerodynamic heating.
Abstract: Water recycling represents an important challenge for many countries, in particular in countries where this natural resource is rare. On the other hand, in many operations, water is used as a cooling medium, as a high proportion of water consumed in industry is used for cooling purposes. Generally this water is rejected directly to the nature. This reject will cause serious environment damages as well as an important waste of this precious element.. On way to solve these problems is to reuse and recycle this warm water, through the use of natural cooling medium, such as air in a heat exchanger unit, known as a cooling tower. A poor performance, design or reliability of cooling towers will result in lower flow rate of cooling water an increase in the evaporation of water, an hence losses of water and energy. This paper which presents an experimental investigate of thermal and hydraulic performances of a mechanical cooling tower, enables to show that the water evaporation rate, Mev, increases with an increase in the air and water flow rates, as well as inlet water temperature and for fixed air flow rates, the pressure drop (ΔPw/Z) increases with increasing , L, due to the hydrodynamic behavior of the air/water flow.
Abstract: The system is made with main distributed components:
First Level: Industrial Computers placed in Control Room (monitors thermal and electrical processes based on the data provided by the second level); Second Level: PLCs which collects data from process and transmits information on the first level; also takes commands from this level which are further, passed to execution elements from third
level; Third Level: field elements consisting in 3 categories: data collecting elements; data transfer elements from the third level to the second; execution elements which take commands from the second
level PLCs and executes them after which transmits the confirmation of execution to them. The purpose of the automatic functioning is the optimization of the co-generative electrical energy commissioning in the national
energy system and the commissioning of thermal energy to the consumers.
The integrated system treats the functioning of all the equipments and devices as a whole: Gas Turbine Units (GTU); MT 20kV Medium Voltage Station (MVS); 0,4 kV Low Voltage Station (LVS); Main Hot Water Boilers (MHW); Auxiliary Hot Water Boilers (AHW); Gas Compressor Unit (GCU); Thermal Agent Circulation
Pumping Unit (TPU); Water Treating Station (WTS).
Abstract: Reactiondiffusion systems are mathematical models that describe how the concentration of one or more substances distributed in space changes under the influence of local chemical reactions in which the substances are converted into each other, and diffusion which causes the substances to spread out in space. The classical representation of a reaction-diffusion system is given by semi-linear parabolic partial differential equations, whose general form is ÔêétX(x, t) = DΔX(x, t), where X(x, t) is the state vector, D is the matrix of the diffusion coefficients and Δ is the Laplace operator. If the solute move in an homogeneous system in thermal equilibrium, the diffusion coefficients are constants that do not depend on the local concentration of solvent and of solutes and on local temperature of the medium. In this paper a new stochastic reaction-diffusion model in which the diffusion coefficients are function of the local concentration, viscosity and frictional forces of solvent and solute is presented. Such a model provides a more realistic description of the molecular kinetics in non-homogenoeus and highly structured media as the intra- and inter-cellular spaces. The movement of a molecule A from a region i to a region j of the space is described as a first order reaction Ai k- → Aj , where the rate constant k depends on the diffusion coefficient. Representing the diffusional motion as a chemical reaction allows to assimilate a reaction-diffusion system to a pure reaction system and to simulate it with Gillespie-inspired stochastic simulation algorithms. The stochastic time evolution of the system is given by the occurrence of diffusion events and chemical reaction events. At each time step an event (reaction or diffusion) is selected from a probability distribution of waiting times determined by the specific speed of reaction and diffusion events. Redi is the software tool, developed to implement the model of reaction-diffusion kinetics and dynamics. It is a free software, that can be downloaded from http://www.cosbi.eu. To demonstrate the validity of the new reaction-diffusion model, the simulation results of the chaperone-assisted protein folding in cytoplasm obtained with Redi are reported. This case study is redrawing the attention of the scientific community due to current interests on protein aggregation as a potential cause for neurodegenerative diseases.
Abstract: There is a great deal of interest in constructing Double Skin Facade (DSF) structures which are considered as modern movement in field of Energy Conservation, renewable energies, and Architecture design. This trend provides many conclusive alternatives which are frequently associated with sustainable building. In this paper a building with Double Skin Facade is considered in the semiarid climate of Tehran, Iran, in order to consider the DSF-s performance during hot seasons. Mathematical formulations calculate solar heat gain by the external skin. Moreover, Computational Fluid Dynamics (CFD) simulations were performed on the case study building to enhance effectiveness of the facade. The conclusion divulged difference of gained energy by the cavity and room with and without blind and louvers. Some solutions were introduced to surge the performance of natural ventilation by plunging the cooling loads in summer.
Abstract: The effect of thermally induced stress on the modal
properties of highly elliptical core optical fibers is studied in this
work using a finite element method. The stress analysis is carried out
and anisotropic refractive index change is calculated using both the
conventional plane strain approximation and the generalized plane
strain approach. After considering the stress optical effect, the modal
analysis of the fiber is performed to obtain the solutions of
fundamental and higher order modes. The modal effective index,
modal birefringence, group effective index, group birefringence, and
dispersion of different modes of the fiber are presented. For
propagation properties, it can be seen that the results depend much on
the approach of stress analysis.