Abstract: The aim of this study was to analyse the most
important parameters determining the quality of the motion structure
of the basic classical dance jump – grand jeté.Research sample
consisted of 8 students of the Dance Conservatory in Brno. Using the
system Simi motion we performed a 3D kinematic analysis of the
jump. On the basis of the comparison of structure quality and
measured data of the grand jeté, we defined the optimal values of the
relevant parameters determining the quality of the performance. The
take-off speed should achieve about 2.4 m·s-1, the optimum take-off
angle is 28 - 30º. The take-off leg should swing backward at the
beginning of the flight phase with the minimum speed of 3.3 m·s-1.If
motor abilities of dancers achieve the level necessary for optimal
performance of a classical dance jump, there is room for certain
variability of the structure of the dance jump.
Abstract: This work presents a comparison between the Annual
Energy Output (AEO) of two commercial vertical-axis wind turbines
(VAWTs) for a low-wind urban site: both a drag-driven and a liftdriven
concepts are examined in order to be installed on top of the
new Via dei Giustinelli building, Trieste (Italy). The power-curves,
taken from the product specification sheets, have been matched to the
wind characteristics of the selected installation site. The influence of
rotor swept area and rated power on the performance of the two
proposed wind turbines have been examined in detail, achieving a
correlation between rotor swept area, electrical generator size and
wind distribution, to be used as a guideline for the calculation of the
AEO.
Abstract: This study aims to assess the environmental hazards
from radon exhalation rate in the soil samples in selected locations in
Iraqi Kurdistan, using passive (CR-39NTDs) and active (RAD7)
detecting method. Radon concentration, effective radium content and
radon exhalation rate were estimated in soil samples that collected at
the depth level of 30 cm inside 124 houses. The results show that the
emanation rate for radon gas was variation from location to other,
depending on the geological formation. Most health risks come from
emanation of radon and its daughter due to its contribution for indoor
radon, so the results showed that there is a linear relationship
between the ratio of soil and indoor radon concentration (CSoil Rn222/
Cindoor Rn222) and the effective radium content in soil samples. The
results show that radon concentration has high and low values in
Hajyawa city and Er. Tyrawa Qr, respectively. A comparison
between our results with that mentioned in international reports was
done.
Abstract: the effects of refining and alkaline chemicals on potential of recycling bleached chemical pulp of bagasse were investigated in this study. Recycling was done until three times. Handsheet properties such as, apparent density, light scattering coefficient, tear index, burst index, breaking length, and fold number according to TAPPI standard were measured. Water retention value also was used to considering the treatments during recycling. Refining enhanced the strength of recycled pulp by increasing fiber flexibility and swelling ability, whereas by applying chemical treatment didn't observe any improvement. The morphology of recycled fiber was considered with scanning electron microscopy (SEM).
Abstract: In this paper, free vibration analysis of carbon nanotube (CNT) reinforced laminated composite panels is presented. Three types of panels such as flat, concave and convex are considered for study. Numerical simulation is carried out using commercially available finite element analysis software ANSYS. Numerical homogenization is employed to calculate the effective elastic properties of randomly distributed carbon nanotube reinforced composites. To verify the accuracy of the finite element method, comparisons are made with existing results available in the literature for conventional laminated composite panels and good agreements are obtained. The results of the CNT reinforced composite materials are compared with conventional composite materials under different boundary conditions.
Abstract: Financial forecasting using machine learning techniques has received great efforts in the last decide . In this ongoing work, we show how machine learning of graphical models will be able to infer a visualized causal interactions between different banks in the Saudi equities market. One important discovery from such learned causal graphs is how companies influence each other and to what extend. In this work, a set of graphical models named Gaussian graphical models with developed ensemble penalized feature selection methods that combine ; filtering method, wrapper method and a regularizer will be shown. A comparison between these different developed ensemble combinations will also be shown. The best ensemble method will be used to infer the causal relationships between banks in Saudi equities market.
Abstract: The effect of different combinations of response
feedback on the performance of active control system on nonlinear
frames has been studied in this paper. To this end different feedback
combinations including displacement, velocity, acceleration and full
response feedback have been utilized in controlling the response of
an eight story bilinear hysteretic frame which has been subjected to a
white noise excitation and controlled by eight actuators which could
fully control the frame. For active control of nonlinear frame
Newmark nonlinear instantaneous optimal control algorithm has been
used which a diagonal matrix has been selected for weighting
matrices in performance index. For optimal design of active control
system while the objective has been to reduce the maximum drift to
below the yielding level, Distributed Genetic Algorithm (DGA) has
been used to determine the proper set of weighting matrices. The
criteria to assess the effect of each combination of response feedback
have been the minimum required control force to reduce the
maximum drift to below the yielding drift. The results of numerical
simulation show that the performance of active control system is
dependent on the type of response feedback where the velocity
feedback is more effective in designing optimal control system in
comparison with displacement and acceleration feedback. Also using
full feedback of response in controller design leads to minimum
control force amongst other combinations. Also the distributed
genetic algorithm shows acceptable convergence speed in solving the
optimization problem of designing active control systems.
Abstract: The present work is a numerical simulation of
nanofluids flow in a double pipe heat exchanger provided with
porous baffles. The hot nanofluid flows in the inner cylinder, whereas
the cold nanofluid circulates in the annular gap. The Darcy-
Brinkman-Forchheimer model is adopted to describe the flow in the
porous regions, and the governing equations with the appropriate
boundary conditions are solved by the finite volume method. The
results reveal that the addition of metallic nanoparticles enhances the
rate of heat transfer in comparison to conventional fluids but this
augmentation is accompanied by an increase in pressure drop. The
highest heat exchanger performances are obtained when
nanoparticles are added only to the cold fluid.
Abstract: In this paper, the construction of fast algorithms for the computation of Periodic Walsh Piecewise-Linear PWL transform and the Periodic Haar Piecewise-Linear PHL transform will be presented. Algorithms for the computation of the inverse transforms are also proposed. The matrix equation of the PWL and PHL transforms are introduced. Comparison of the computational requirements for the periodic piecewise-linear transforms and other orthogonal transforms shows that the periodic piecewise-linear transforms require less number of operations than some orthogonal transforms such as the Fourier, Walsh and the Discrete Cosine transforms.
Abstract: An automated wood recognition system is designed to
classify tropical wood species.The wood features are extracted based
on two feature extractors: Basic Grey Level Aura Matrix (BGLAM)
technique and statistical properties of pores distribution (SPPD)
technique. Due to the nonlinearity of the tropical wood species
separation boundaries, a pre classification stage is proposed which
consists ofKmeans clusteringand kernel discriminant analysis (KDA).
Finally, Linear Discriminant Analysis (LDA) classifier and KNearest
Neighbour (KNN) are implemented for comparison purposes.
The study involves comparison of the system with and without pre
classification using KNN classifier and LDA classifier.The results
show that the inclusion of the pre classification stage has improved
the accuracy of both the LDA and KNN classifiers by more than
12%.
Abstract: Today air-core coils (ACC) are a viable alternative to
ferrite-core coils in a range of applications due to their low induction
effect. An analytical study was carried out and the results were used as
a guide to understand the relationship between the magnet-coil
distance and the resulting attractive magnetic force. Four different
ACC models were fabricated for experimental study. The variation in
the models included the dimensions, the number of coil turns and the
current supply to the coil. Comparison between the analytical and
experimental results for all the models shows an average discrepancy
of less than 10%. An optimized ACC design was selected for the
scanner which can provide maximum magnetic force.
Abstract: This paper describes a new method for affine parameter
estimation between image sequences. Usually, the parameter
estimation techniques can be done by least squares in a quadratic
way. However, this technique can be sensitive to the presence
of outliers. Therefore, parameter estimation techniques for various
image processing applications are robust enough to withstand the
influence of outliers. Progressively, some robust estimation functions
demanding non-quadratic and perhaps non-convex potentials adopted
from statistics literature have been used for solving these. Addressing
the optimization of the error function in a factual framework for
finding a global optimal solution, the minimization can begin with
the convex estimator at the coarser level and gradually introduce nonconvexity
i.e., from soft to hard redescending non-convex estimators
when the iteration reaches finer level of multiresolution pyramid.
Comparison has been made to find the performance of the results
of proposed method with the results found individually using two
different estimators.
Abstract: This paper presents a comparison of average outgoing
quality limit of the MCSP-2-C plan with MCSP-C when MCSP-2-C
has been developed from MCSP-C. The parameters used in MCSP-2-
C are: i (the clearance number), c (the acceptance number), m (the
number of conforming units to be found before allowing c nonconforming
units in the sampling inspection), f1 and f2 (the sampling
frequency at level 1 and 2, respectively). The average outgoing
quality limit (AOQL) values from two plans were compared and we
found that for all sets of i, r, and c values, MCSP-2-C gives higher
values than MCSP-C. For all sets of i, r, and c values, the average
outgoing quality values of MCSP-C and MCSP-2-C are similar when
p is low or high but is difference when p is moderate.
Abstract: Nowadays there is a growing interest in biofuel production in most countries because of the increasing concerns about hydrocarbon fuel shortage and global climate changes, also for enhancing agricultural economy and producing local needs for transportation fuel. Ethanol can be produced from biomass by the hydrolysis and sugar fermentation processes. In this study ethanol was produced without using expensive commercial enzymes from sugarcane bagasse. Alkali pretreatment was used to prepare biomass before enzymatic hydrolysis. The comparison between NaOH, KOH and Ca(OH)2 shows NaOH is more effective on bagasse. The required enzymes for biomass hydrolysis were produced from sugarcane solid state fermentation via two fungi: Trichoderma longibrachiatum and Aspergillus niger. The results show that the produced enzyme solution via A. niger has functioned better than T. longibrachiatum. Ethanol was produced by simultaneous saccharification and fermentation (SSF) with crude enzyme solution from T. longibrachiatum and Saccharomyces cerevisiae yeast. To evaluate this procedure, SSF of pretreated bagasse was also done using Celluclast 1.5L by Novozymes. The yield of ethanol production by commercial enzyme and produced enzyme solution via T. longibrachiatum was 81% and 50% respectively.
Abstract: The objective of this work is to explicit knowledge on the interactions between the chlorophyll-a and nine meroplankton larvae of epibenthonic fauna. The studied case is the Arraial do Cabo upwelling system, Southeastern of Brazil, which provides different environmental conditions. To assess this information a network approach based in probability estimative was used. Comparisons among the generated graphs are made in the light of different water masses, application of Shannon biodiversity index, and the closeness and betweenness centralities measurements. Our results show the main pattern among different water masses and how the core organisms belonging to the network skeleton are correlated to the main environmental variable. We conclude that the approach of complex networks is a promising tool for environmental diagnostic.
Abstract: Precise frequency estimation methods for pulseshaped echoes are a prerequisite to determine the relative velocity between sensor and reflector. Signal frequencies are analysed using three different methods: Fourier Transform, Chirp ZTransform and the MUSIC algorithm. Simulations of echoes are performed varying both the noise level and the number of reflecting points. The superposition of echoes with a random initial phase is found to influence the precision of frequency estimation severely for FFT and MUSIC. The standard deviation of the frequency using FFT is larger than for MUSIC. However, MUSIC is more noise-sensitive. The distorting effect of superpositions is less pronounced in experimental data.
Abstract: Principle component analysis is often combined with
the state-of-art classification algorithms to recognize human faces.
However, principle component analysis can only capture these
features contributing to the global characteristics of data because it is a
global feature selection algorithm. It misses those features
contributing to the local characteristics of data because each principal
component only contains some levels of global characteristics of data.
In this study, we present a novel face recognition approach using
non-negative principal component analysis which is added with the
constraint of non-negative to improve data locality and contribute to
elucidating latent data structures. Experiments are performed on the
Cambridge ORL face database. We demonstrate the strong
performances of the algorithm in recognizing human faces in
comparison with PCA and NREMF approaches.
Abstract: The paper discusses the results obtained to predict
reinforcement in singly reinforced beam using Neural Net (NN),
Support Vector Machines (SVM-s) and Tree Based Models. Major
advantage of SVM-s over NN is of minimizing a bound on the
generalization error of model rather than minimizing a bound on
mean square error over the data set as done in NN. Tree Based
approach divides the problem into a small number of sub problems to
reach at a conclusion. Number of data was created for different
parameters of beam to calculate the reinforcement using limit state
method for creation of models and validation. The results from this
study suggest a remarkably good performance of tree based and
SVM-s models. Further, this study found that these two techniques
work well and even better than Neural Network methods. A
comparison of predicted values with actual values suggests a very
good correlation coefficient with all four techniques.
Abstract: The Lattice Boltzmann Method (LBM) with double populations is applied to solve the steady-state laminar natural convective heat transfer in a triangular cavity filled with water. The bottom wall is heated, the vertical wall is cooled, and the inclined wall is kept adiabatic. The buoyancy effect was modeled by applying the Boussinesq approximation to the momentum equation. The fluid velocity is determined by D2Q9 LBM and the energy equation is discritized by D2Q4 LBM to compute the temperature field. Comparisons with previously published work are performed and found to be in excellent agreement. Numerical results are obtained for a wide range of parameters: the Rayleigh number from to and the inclination angle from 0° to 360°. Flow and thermal fields were exhibited by means of streamlines and isotherms. It is observed that inclination angle can be used as a relevant parameter to control heat transfer in right-angled triangular enclosures.
Abstract: Nowadays, we are facing with network threats that
cause enormous damage to the Internet community day by day. In
this situation, more and more people try to prevent their network
security using some traditional mechanisms including firewall,
Intrusion Detection System, etc. Among them honeypot is a versatile
tool for a security practitioner, of course, they are tools that are meant
to be attacked or interacted with to more information about attackers,
their motives and tools. In this paper, we will describe usefulness of
low-interaction honeypot and high-interaction honeypot and
comparison between them. And then we propose hybrid honeypot
architecture that combines low and high -interaction honeypot to
mitigate the drawback. In this architecture, low-interaction honeypot
is used as a traffic filter. Activities like port scanning can be
effectively detected by low-interaction honeypot and stop there.
Traffic that cannot be handled by low-interaction honeypot is handed
over to high-interaction honeypot. In this case, low-interaction
honeypot is used as proxy whereas high-interaction honeypot offers
the optimal level realism. To prevent the high-interaction honeypot
from infections, containment environment (VMware) is used.