Abstract: The relationship between different types of Molybdenum disulfide greases under extreme pressure loading and different speed situations have been studied using Design of Experiment (DOE) under 1200rpm steady state rotational speed and cyclic frequencies between 2400 and 1200rpm using a Plint machine software to set up the different rotational speed situations.
Research described here is aimed at providing good friction and wear performance while optimizing cyclic frequencies and MoS2 concentration due to the recent concern about grease behavior in extreme pressure applications. Extreme load of 785 Newton was used in conjunction with different cyclic frequencies (2400rpm -3.75min, 1200rpm -7.5min, 2400rpm -3.75min, 1200rpm -7.5min), to examine lithium based grease with and without MoS2 for equal number of revolutions, and a total run of 36000 revolutions; then compared to 1200rpm steady speed for the same total number of revolutions. 4 Ball wear tester was utilized to run large number of experiments randomly selected by the DOE software. The grease was combined with fine grade MoS2 or technical grade then heated to 750C and the wear scar width was collected at the end of each test. DOE model validation results verify that the data were very significant and can be applied to a wide range of extreme pressure applications. Based on simulation results and Scanning Electron images (SEM), it has been found that wear was largely dependent on the cyclic frequency condition. It is believed that technical grade MoS2 greases under faster cyclic speeds perform better and provides antiwear film that can resist extreme pressure loadings. Figures showed reduced wear scars width and improved frictional values.
Abstract: The governing differential equations of laminated
plate utilizing trigonometric shear deformation theory are derived
using energy approach. The governing differential equations
discretized by different radial basis functions are used to predict the
free vibration behavior of symmetric laminated composite plates.
Effect of orthotropy and span to thickness ratio on frequency
parameter of simply supported laminated plate is presented.
Numerical results show the accuracy and good convergence of radial
basis functions.
Abstract: In this work, we try to find the best setting
of Computational Fluid Dynamic solver available for the problems in
the field of supersonic internal flows. We used the supersonic air-toair
ejector to represent the typical problem in focus. There are
multiple oblique shock waves, shear layers, boundary layers
and normal shock interacting in the supersonic ejector making this
device typical in field of supersonic inner flows. Modeling of shocks
in general is demanding on the physical model of fluid, because
ordinary conservation equation does not conform to real conditions in
the near-shock region as found in many works. From these reasons,
we decided to take special care about solver setting in this article by
means of experimental approach of color Schlieren pictures and
pneumatic measurement. Fast pressure transducers were used to
measure unsteady static pressure in regimes with normal shock in
mixing chamber. Physical behavior of ejector in several regimes is
discussed. Best choice of eddy-viscosity setting is discussed on the
theoretical base. The final verification of the k-ω SST is done on the
base of comparison between experiment and numerical results.
Abstract: Recognizing human action from videos is an active
field of research in computer vision and pattern recognition. Human
activity recognition has many potential applications such as video
surveillance, human machine interaction, sport videos retrieval and
robot navigation. Actually, local descriptors and bag of visuals words
models achieve state-of-the-art performance for human action
recognition. The main challenge in features description is how to
represent efficiently the local motion information. Most of the
previous works focus on the extension of 2D local descriptors on 3D
ones to describe local information around every interest point. In this
paper, we propose a new spatio-temporal descriptor based on a spacetime
description of moving points. Our description is focused on an
Accordion representation of video which is well-suited to recognize
human action from 2D local descriptors without the need to 3D
extensions. We use the bag of words approach to represent videos.
We quantify 2D local descriptor describing both temporal and spatial
features with a good compromise between computational complexity
and action recognition rates. We have reached impressive results on
publicly available action data set
Abstract: Optical network uses a tool for routing called Latin
router. These routers use particular algorithms for routing. For
example, we can refer to LDF algorithm that uses backtracking (one
of CSP methods) for problem solving. In this paper, we proposed
new approached for completion routing table (DRA&CRA
algorithm) and compare with pervious proposed ways and showed
numbers of backtracking, blocking and run time for DRA algorithm
less than LDF and CRA algorithm.
Abstract: Recent research has shown that milk proteins can
yield bioactive peptides with opioid, mineral binding,
cytomodulatory, antihypertensive, immunostimulating, antimicrobial
and antioxidative activity in the human body. Bioactive peptides are
encrypted in milk proteins and are only released by enzymatic
hydrolysis in vivo during gastrointestinal digestion, food processing
or by microbial enzymes in fermented products. At present
significant research is being undertaken on the health effects of
bioactive peptides. A variety of naturally formed bioactive peptides
have been found in fermented dairy products, such as yoghurt, sour
milk and cheese. In particular, antihypertensive peptides have been
identified in fermented milks, whey and ripened cheese. Some of
these peptides have been commercialized in the form of fermented
milks. Bioactive peptides have the potential to be used in the
formulation of health-enhancing nutraceuticals, and as potent drugs
with well defined pharmacological effects.
Abstract: Tehran, one of the heavily-populated capitals, is
severely suffering from increasing air pollution. To show a
documented trend of such pollutants during last years, plane tree
species (Platanus orientalis) were suited to be studied as indicators,
for the species have been planted throughout the city many years
ago. Two areas (Saadatabad and Narmak districts) allotting different
contents of crowed and highly-traffic routs but the same ecological
characteristics were selected. Twelve sample individuals were cored
twice perpendicularly in each area. Tree-rings of each core were
measured by a binocular microscope and separated annually for the
last 25 years. Two heavy metals including Cd and Pb accompanied
by a mineral element (Ca) were analyzed using Hatch method. Treerings
analysis of the two areas showed different groups in term of
physiologically ability as the growths were plunged during the last
10 years in Saadatabad district and showed a slight decrease in the
same period for another studying area. In direct contrast to
decreasing growth trend in Saadatabad, all three mentioned elements
increased sharply during last 25 years in the same area. When it came
to Narmak district, the trend was completely different with
Saadatabad. There were some fluctuations in absorbing trace
elements like tree-rings widths were, yet calcium showed an upward
trend all the last 25 years. The results of the study proved the
possibility of using tree species of each region to monitor its air
pollution trends of the past, hence to depict a pollution assessment of
a populated city for last years and then to make appropriate decisions
for the future as it is well-known what the trend is. On the other
hand, risen values of calcium (as the stress-indicator element)
accompanied by increased trace elements suggests non-sustainable
state of the trees.
Abstract: Geosynthetics have proved to be suitable for
reinforced soil retaining walls. Based on the increasing uses of
geosynthetic reinforced soil systems in the regions, which bear
frequent earthquakes, the study of dynamic behavior of structures
seems necessary. Determining the reinforcement forces is; therefore,
one of the most important and main points of discussions in
designing retaining walls, by which we prevent from conservative
planning. Thus, this paper intended to investigate the effects of such
parameters as wall height, acceleration type, vertical spacing of
reinforcement, type of reinforcement and soil type on forces and
deformation through numerical modeling of the geosynthetic
reinforced soil retaining walls (GRSRW) under dynamic loading with
finite difference method by using FLAC. The findings indicate rather
positive results with each parameter.
Abstract: This paper proposes a neural network weights and
topology optimization using genetic evolution and the
backpropagation training algorithm. The proposed crossover and
mutation operators aims to adapt the networks architectures and
weights during the evolution process. Through a specific inheritance
procedure, the weights are transmitted from the parents to their
offsprings, which allows re-exploitation of the already trained
networks and hence the acceleration of the global convergence of the
algorithm. In the preprocessing phase, a new feature extraction
method is proposed based on Legendre moments with the Maximum
entropy principle MEP as a selection criterion. This allows a global
search space reduction in the design of the networks. The proposed
method has been applied and tested on the well known MNIST
database of handwritten digits.
Abstract: This work provides a practical method for the
development of rural road networks in rural areas of developing
countries. The proposed methodology enables to determine
obligatory points in the rural road network maximizing the number of
settlements that have access to basic services within a given
maximum distance. The proposed methodology is simple and
practical, hence, highly applicable to real-world scenarios, as
demonstrated in the definition of the road network for the rural areas
of Nepal.
Abstract: Mobile ad hoc network is a collection of mobile
nodes communicating through wireless channels without any
existing network infrastructure or centralized administration.
Because of the limited transmission range of wireless network
interfaces, multiple "hops" may be needed to exchange data
across the network. Consequently, many routing algorithms
have come into existence to satisfy the needs of
communications in such networks. Researchers have
conducted many simulations comparing the performance of
these routing protocols under various conditions and
constraints. One question that arises is whether speed of nodes
affects the relative performance of routing protocols being
studied. This paper addresses the question by simulating two
routing protocols AODV and DSDV. Protocols were
simulated using the ns-2 and were compared in terms of
packet delivery fraction, normalized routing load and average
delay, while varying number of nodes, and speed.
Abstract: This paper was aimed to survey the level of awareness
of traditional grocery stores in Bangkok in these categories: location,
service quality, risk, shopping, worthwhile, shopping satisfaction, and
future shopping intention. The paper was also aimed to survey factors
influencing the decision to shop at traditional grocery stores in
Bangkok in the future. The findings revealed that consumers had a
high level of awareness of traditional grocery stores in Bangkok.
Consumers were aware that the price was higher and it was riskier to
buy goods and services at traditional grocery stores but they still had
a high level of preference to patronage traditional grocery stores. This
was due to the reasons that there was a high level of satisfaction from
the factors of the friendliness of the owner, the ability to negotiate the
price, the ability to buy on credit, free delivery, and the enjoyment to
meet with other customers in the same neighborhood.
Abstract: The sonochemical decolorization and degradation of azo dye Methyl violet using Fenton-s reagent in the presence of a high-frequency acoustic field has been investigated. Dyeing and textile effluents are the major sources of azo dyes, and are most troublesome among industrial wastewaters, causing imbalance in the eco-system. The effect of various operating conditions (initial concentration of dye, liquid-phase temperature, ultrasonic power and frequency and process time) on sonochemical degradation was investigated. Conversion was found to increase with increase in initial concentration, temperature, power level and frequency. Both horntype and tank-type sonicators were used, at various power levels (250W, 400W and 500W) for frequencies ranging from 20 kHz - 1000 kHz. A 'Process Intensification' parameter PI, was defined to quantify the enhancement of the degradation reaction by ultrasound when compared to control (i.e., without ultrasound). The present work clearly demonstrates that a high-frequency ultrasonic bath can be used to achieve higher process throughput and energy efficiency at a larger scale of operation.
Abstract: This paper describes topic of computer simulation with regard to the ground movement above an underground mine. Simulation made with software package ADINA for nonlinear elastic-plastic analysis with finite elements method. The one of representative profiles from Mine 'Stara Jama' in Zenica has been investigated. A collection and selection of both geo-mechanical data and geometric parameters of the mine was necessary for performing these simulations. Results of estimation have been compared with measured values (vertical displacement of surface), and then simulation performed with assumed dynamic and dimensions of excavation, over a period of time. Results are presented with bitmaps and charts.
Abstract: To produce sugar and ethanol, sugarcane processing
generates several agricultural residues, being straw and bagasse is
considered as the main among them. And what to do with this
residues has been subject of many studies and experiences in an
industry that, in recent years, highlighted by the ability to transform
waste into valuable products such as electric power. Cellulose is the
main component of these materials. It is the most common organic
polymer and represents about 1.5 x 1012 tons of total production of
biomass per year and is considered an almost inexhaustible source of
raw material. Pretreatment with mineral acids is one of the most
widely used as stage of cellulose extraction from lignocellulosic
materials for solubilizing most of the hemicellulose content. This
study had as goal to find the best reaction time of sugarcane bagasse
pretreatment with sulfuric acid in order to minimize the losses of
cellulose concomitantly with the highest possible removal of
hemicellulose and lignin. It was found that the best time for this
reaction was 40 minutes, in which it was reached a loss of
hemicelluloses around 70% and lignin and cellulose, around 15%.
Over this time, it was verified that the cellulose loss increased and
there was no loss of lignin and hemicellulose.
Abstract: This paper studies mechanical buckling of
functionally graded beams subjected to axial compressive load that is
simply supported at both ends lies on a continuous elastic foundation.
The displacement field of beam is assumed based on Engesser-Timoshenko beam theory. Applying the Hamilton's principle, the
equilibrium equation is established. The influences of dimensionless geometrical parameter, functionally graded index and foundation
coefficient on the critical buckling load of beam are presented. To investigate the accuracy of the present analysis, a compression study
is carried out with a known data.
Abstract: Design of a constant chord propeller is presented in
this paper in order to reduce propeller-s design procedure-s costs. The
design process was based on Lock and Goldstein-s techniques of
propeller design and analysis. In order to calculate optimum chord of
propeller, chord of a referential element is generalized as whole
blades chord. The design outcome which named CS-X-1 is modeled
& analyzed by CFD methods using K-ε: R.N.G turbulence model.
Convergence of results of two codes proved that outcome results of
design process are reliable. Design result is a two-blade propeller
with a total diameter of 1.1 meter, radial velocity of 3000 R.P.M,
efficiency above .75 and power coefficient near 1.05.
Abstract: One of the efficient factors in comprehensive
development of an area is to provide water sources and on the other
hand the appropriate management of them. Population growth and
nourishment security for such a population necessitate the
achievement of constant development besides the reforming of
traditional management in order to increase the profit of sources; In
this case, the constant exploitation of sources for the next generations
will be considered in this program. The achievement of this
development without the consideration and possibility of water
development will be too difficult. Zayanderood basin with 41500
areas in square kilometers contains 7 sub-basins and 20 units of
hydrologic. In this basin area, from the entire environment
descending, just a small part will enter into the river currents and the
rest will be out of efficient usage by various ways. The most
important surface current of this basin is Zayanderood River with
403 kilometers length which is originated from east slopes of Zagros
mount and after draining of this basin area it will enter into
Gaavkhooni pond. The existence of various sources and
consumptions of water in Zayanderood basin, water transfer of the
other basin areas into this basin, of course the contradiction between
the upper and lower beneficiaries, the existence of worthwhile
natural ecosystems such as Gaavkhooni swamp in this basin area and
finally, the drought condition and lack of water in this area all
necessitate the existence of comprehensive management of water
sources in this central basin area of Iran as this method is a kind of
management which considers the development and the management
of water sources as an equilibrant way to increase the economical
and social benefits. In this study, it is tried to survey the network of
surface water sources of basin in upper and lower sections; at the
most, according to the difficulties and deficiencies of an efficient
management of water sources in this basin area, besides the
difficulties of water draining and the destructive phenomenon of
flood-water, the appropriate guidelines according to the region
conditions are presented in order to prevent the deviation of water in
upper sections and development of regions in lower sections of
Zayanderood dam.
Abstract: With the fast progression of data exchange in electronic way, information security is becoming more important in data storage and transmission. Because of widely using images in industrial process, it is important to protect the confidential image data from unauthorized access. In this paper, we analyzed current image encryption algorithms and compression is added for two of them (Mirror-like image encryption and Visual Cryptography). Implementations of these two algorithms have been realized for experimental purposes. The results of analysis are given in this paper.
Abstract: Computational simulation of steam flow and heat transfer in power plant condensers on the basis of the threedimensional mathematical model for the flow through porous media is presented. In order to solve the mathematical model of steam flow and heat transfer in power plant condensers, the Streamline Upwind Petrov-Galerkin finite element method is applied. By comparison of the results of simulation with experimental results about an experimental condenser, it is confirmed that SUPG finite element method can be successfully applied for solving the three-dimensional mathematical model of steam flow and heat transfer in power plant condensers.