Abstract: In this paper, vapour-liquid critical locus for the
binary system acetone + chloroform was determined experimentally
over the whole range of composition. The critical property
measurements were carried out using a dynamic-synthetic apparatus,
employed in the dynamic mode. The critical points are visually
determined by observing the critical opalescence and the
simultaneous disappearance and reappearance of the meniscus in the
middle of a high-pressure view cell which withstands operations up
to 673K and 20MPa. The experimental critical points measured in
this work were compared to those available in literature.
Abstract: The ferroelectric behavior of barium strontium
titanate (BST) in thin film form has been investigated in order to
study the possibility of using BST for ferroelectric gate-field effect
transistor (FeFET) for memory devices application. BST thin films
have been fabricated as Al/BST/Pt/SiO2/Si-gate configuration. The
variation of the dielectric constant (ε) and tan δ with frequency have
been studied to ensure the dielectric quality of the material. The
results show that at low frequencies, ε increases as the Ba content
increases, whereas at high frequencies, it shows the opposite
variation, which is attributed to the dipole dynamics. tan δ shows low
values with a peak at the mid-frequency range. The ferroelectric
behavior of the Al/BST/Pt/SiO2/Si has been investigated using C-V
characteristics. The results show that the strength of the ferroelectric
hysteresis loop increases as the Ba content increases; this is attributed
to the grain size and dipole dynamics effect.
Abstract: The article deals with pneumatic and hot wire
anemometry measurement on subsonic axi-symmetric air ejector.
Performances of the ejector with and without pulsations of primary
flow are compared, measuring of characteristic pressures and mass
flow rates are performed and ejector efficiency is evaluated. The
pulsations of primary flow are produced by a synthetic jet generator,
which is placed in the supply line of the primary flow just in front of
the primary nozzle. The aim of the pulsation is to intensify the
mixing process. In the article we present: Pressure measuring of
pulsation on the mixing chamber wall, behind the mixing chamber
and behind the diffuser measured by fast pressure transducers and
results of hot wire anemometry measurement. It was found out that
using of primary flow pulsations yields higher back pressure behind
the ejector and higher efficiency. The processes in this ejector and
influences of primary flow pulsations on the mixing processes are
described.
Abstract: This paper investigates the optimization problem of
multi-product aggregate production planning (APP) with fuzzy data.
From a comprehensive viewpoint of conserving the fuzziness of input
information, this paper proposes a method that can completely
describe the membership function of the performance measure. The
idea is based on the well-known Zadeh-s extension principle which
plays an important role in fuzzy theory. In the proposed solution
procedure, a pair of mathematical programs parameterized by
possibility level a is formulated to calculate the bounds of the
optimal performance measure at a . Then the membership function of
the optimal performance measure is constructed by enumerating
different values of a . Solutions obtained from the proposed method
contain more information, and can offer more chance to achieve the
feasible disaggregate plan. This is helpful to the decision-maker in
practical applications.
Abstract: Lignocellulosic materials are new targeted source to
produce second generation biofuels like biobutanol. However, this
process is significantly resisted by the native structure of biomass.
Therefore, pretreatment process is always essential to remove
hemicelluloses and lignin prior to the enzymatic hydrolysis.
The goals of pretreatment are removing hemicelluloses and
lignin, increasing biomass porosity, and increasing the enzyme
accessibility. The main goal of this research is to study the important
variables such as pretreatment temperature and time, which can give
the highest total sugar yield in pretreatment step by using dilute
phosphoric acid. After pretreatment, the highest total sugar yield of
13.61 g/L was obtained under an optimal condition at 140°C for 10
min of pretreatment time by using 1.75% (w/w) H3PO4 and at 15:1
liquid to solid ratio. The total sugar yield of two-stage process
(pretreatment+enzymatic hydrolysis) of 27.38 g/L was obtained.
Abstract: Kuwait-s electric power system is vertically integrated
organization owned and operated by the government. For more than
five decades, the government of Kuwait has provided relatively
reliable electric services to consumers with subsidized electric
service fees. Given the country-s rapid socio-economical
development and consequently the increase of electricity demand, a
question that inflicts itself: Is it necessary to reform the power system
to face the fast growing demand? This paper recommends that the
government should consider the private sector as a partner in
operating the power system. Therefore, power system restructuring is
needed to allow such partnership. There are challenges that prevent
such restructuring. Abstract recommendations toward resolving these
challenges are proposed.
Abstract: The need to increase the efficiency of health care
systems is becoming an obligation, and one of area of improvement
is the discharge process. The objective of this work is to minimize
the patients discharge time (for insured patients) to be less than 50
minutes by using six sigma approach, this improvement will also:
lead to an increase in customer satisfaction, increase the number of
admissions and turnover on the rooms, increase hospital
profitability.Three different departments were considered in this
study: Female, Male, and Paediatrics. Six Sigma approach coupled
with simulation has been applied to reduce the patients discharge
time for pediatrics, female, and male departments at hospital. Upon
applying these recommendations at hospital: 60%, 80%, and 22% of
insured female, male, and pediatrics patients respectively will have
discharge time less than the upper specification time i.e. 50 min.
Abstract: Ontologies are broadly used in the context of networked home environments. With ontologies it is possible to define and store context information, as well as to model different kinds of physical environments. Ontologies are central to networked home environments as they carry the meaning. However, ontologies and the OWL language is complex. Several ontology visualization approaches have been developed to enhance the understanding of ontologies. The domain of networked home environments sets some special requirements for the ontology visualization approach. The visualization tool presented here, visualizes ontologies in a domain-specific way. It represents effectively the physical structures and spatial relationships of networked home environments. In addition, it provides extensive interaction possibilities for editing and manipulating the visualization. The tool shortens the gap from beginner to intermediate OWL ontology reader by visualizing instances in their actual locations and making OWL ontologies more interesting and concrete, and above all easier to comprehend.
Abstract: High Pressure Raman scattering measurements of KDP:Mn were performed at room temperatures. The X-ray powder diffraction patterns taken at room temperature by Rietveld refinement showed that doped samples of KDP-Mn have the same tetragonal structure of a pure KDP crystal, but with a contraction of the crystalline cell. The behavior of the Raman spectra, in particular the emergence of a new modes at 330 cm-1, indicates that KDP:Mn undergoes a structural phase transition with onset at around 4 GP. First principle density-functional theory (DFT) calculations indicate that tetrahedral rotation with pressure is predominantly around the c crystalline direction. Theoretical results indicates that pressure induced tetrahedral rotations leads to change tetrahedral neighborhood, activating librations/bending modes observed for high pressure phase of KDP:Mn with stronger Raman activity.
Abstract: The goal of this paper is to develop a model to
integrate “pricing" and “advertisement" for short life cycle products,
such as branded fashion clothing products. To achieve this goal, we
apply the concept of “Dynamic Pricing". There are two classes of
advertisements, for the brand (regardless of product) and for a
particular product. Advertising the brand affects the demand and
price of all the products. Thus, the model considers all these products
in relation with each other. We develop two different methods to
integrate both types of advertisement and pricing. The first model is
developed within the framework of dynamic programming. However,
due to the complexity of the model, this method cannot be applicable
for large size problems. Therefore, we develop another method,
called hieratical approach, which is capable of handling the real
world problems. Finally, we show the accuracy of this method, both
theoretically and also by simulation.
Abstract: Quantitative precipitation forecast (QPF) from
atmospheric model as input to hydrological model in an integrated
hydro-meteorological flood forecasting system has been operational
in many countries worldwide. High-resolution numerical weather
prediction (NWP) models with grid cell sizes between 2 and 14 km
have great potential in contributing towards reasonably accurate QPF.
In this study the potential of two NWP models to forecast
precipitation for a flood-prone area in a tropical region is examined.
The precipitation forecasts produced from the Fifth Generation Penn
State/NCAR Mesoscale (MM5) and Weather Research and
Forecasting (WRF) models are statistically verified with the observed
rain in Kelantan River Basin, Malaysia. The statistical verification
indicates that the models have performed quite satisfactorily for low
and moderate rainfall but not very satisfactory for heavy rainfall.
Abstract: As a company competitiveness depends more and more on the relationship with its stakeholders, the topic of companystakeholder fit is becoming increasingly important. This fit affects the extent to which a stakeholder perceives CSR company commitment, values and behaviors and, therefore, stakeholder identification in a company and his/her loyalty to it. Consequently, it is important to measure the alignment or the gap between stakeholder CSR demands, values, preferences and perceptions, and the company CSR disclosed commitment, values and policies. In this paper, in order to assess the company-stakeholder fit about corporate responsibility, an innovative CSR fit positioning matrix is proposed. This matrix is based on the measurement of a company CSR disclosed commitment and stakeholder perceived and required commitment. The matrix is part of a more complex methodology based on Global Reporting Initiative (GRI) indicators, content analysis and stakeholder questionnaires. This methodology provides appropriate indications for helping companies to achieve CSR company-stakeholder fit, by leveraging both CSR commitment and communication. Moreover, it could be used by top management for comparing different companies and stakeholders, and for planning specific CSR strategies, policies and activities.
Abstract: The incidences of dengue hemorrhagic disease (DHF)
over the long term exhibit a seasonal behavior. It has been
hypothesized that these behaviors are due to the seasonal climate
changes which in turn induce a seasonal variation in the incubation
period of the virus while it is developing the mosquito. The standard
dynamic analysis is applied for analysis the Susceptible-Exposed-
Infectious-Recovered (SEIR) model which includes an annual
variation in the length of the extrinsic incubation period (EIP). The
presence of both asymptomatic and symptomatic infections is
allowed in the present model. We found that dynamic behavior of the
endemic state changes as the influence of the seasonal variation of
the EIP becomes stronger. As the influence is further increased, the
trajectory exhibits sustained oscillations when it leaves the chaotic
region.
Abstract: Five vegetables (spinach, lettuce, cabbage, tomato, and onion) were freshly harvested from the Alau Dam and Gongulong agricultural areas for the determination of some organochlorine pesticide residues (o, p-DDE, p,p’-DDD, o,p’-DDD, p,p’-DDT, α-BHC, γ-BHC, metoxichlor, lindane, endosulfan dieldrin, and aldrin.) Soil samples were also collected at different depths for the determination of the above pesticides. Samples collection and preparation were conducted using standard procedures. The concentrations of all the pesticides in the soil and vegetable samples were determined using GC/MS SHIMADZU (GC-17A) equipped with electron capture detector (ECD). The highest concentration was that of p,p’-DDD (132.4±13.45µg/g) which was observed in the leaf of cabbage, while the lowest concentration was that of p,p’-DDT (2.34µg/g) was observed in the root of spinach. Similar trends were observed at the Gongulong agricultural area, with p,p’-DDD having the highest concentration of 153.23µg/g in the leaf of cabbage, while the lowest concentration was that of p,p’-DDT (12.45µg/g) which was observed in the root of spinach. α-BHC, γ-BHC, Methoxychlor, and lindane were detected in all the vegetable samples studied. The concentrations of all the pesticides in the soil samples were observed to be higher at a depth of 21-30cm, while the lowest concentrations were observed at a depth of 0-10cm. The concentrations of all the pesticides in the vegetables and soil samples from the two agricultural sites were observed to be at alarming levels, much higher than the maximum residue limits (MRLs) and acceptable daily intake values (ADIs) .The levels of the pesticides observed in the vegetables and soil samples investigated, are of such a magnitude that calls for special attention and laws to regulate the use and circulation of such chemicals. Routine monitoring of pesticide residues in these study areas is necessary for the prevention, control and reduction of environmental pollution, so as to minimize health risks.
Abstract: Three dimensional analysis of thermal model in laser
full penetration welding, Nd:YAG, by transparent mode DP600 alloy
steel 1.25mm of thickness and gap of 0.1mm. Three models studied
the influence of thermal dependent temperature properties, thermal
independent temperature and the effect of peak value of specific heat
at phase transformation temperature, AC1, on the transient
temperature. Another seven models studied the influence of
discretization, meshes on the temperature distribution in weld plate.
It is shown that for the effects of thermal properties, the errors less
4% of maximum temperature in FZ and HAZ have identified. The
minimum value of discretization are at least one third increment per
radius for temporal discretization and the spatial discretization
requires two elements per radius and four elements through thickness
of the assembled plate, which therefore represent the minimum
requirements of modeling for the laser welding in order to get
minimum errors less than 5% compared to the fine mesh.
Abstract: The technique of inducing micro ecosystem
restoration is one of aquatic ecology engineering methods used to
retrieve the polluted water. Batch scale study, pilot plant study, and
field study were carried out to observe the eutrophication using the
Inducing Ecology Restorative Symbiosis Agent (IERSA) consisting
mainly degraded products by using lactobacillus, saccharomycete,
and phycomycete. The results obtained from the experiments of the
batch scale and pilot plant study allowed us to development the
parameters for the field study. A pond, 5 m to the outlet of a lake,
with an area of 500 m2 and depth of 0.6-1.2 m containing about 500
tons of water was selected as a model. After the treatment with 10
mg IERSA/L water twice a week for 70 days, the micro restoration
mechanisms consisted of three stages (i.e., restoration, impact
maintenance, and ecology recovery experiment after impact). The
COD, TN, TKN, and chlorophyll a were reduced significantly in the
first week. Although the unexpected heavy rain and contaminate
from sewage system might slow the ecology restoration. However,
the self-cleaning function continued and the chlorophyll a reduced
for 50% in one month. In the 4th week, amoeba, paramecium, rotifer,
and red wriggle worm reappeared, and the number of fish flies
appeared up to1000 fish fries/m3. Those results proved that inducing
restorative mechanism can be applied to improve the eutrophication
and to control the growth of algae in the lakes by gaining the selfcleaning
through inducing and competition of microbes. The
situation for growth of fishes also can reach an excellent result due to
the improvement of water quality.
Abstract: In this paper a novel scheme for watermarking digital
audio during its compression to MPEG-1 Layer III format is
proposed. For this purpose we slightly modify some of the selected
MDCT coefficients, which are used during MPEG audio
compression procedure. Due to the possibility of modifying different
MDCT coefficients, there will be different choices for embedding the
watermark into audio data, considering robustness and transparency
factors. Our proposed method uses a genetic algorithm to select the
best coefficients to embed the watermark. This genetic selection is
done according to the parameters that are extracted from the
perceptual content of the audio to optimize the robustness and
transparency of the watermark. On the other hand the watermark
security is increased due to the random nature of the genetic
selection. The information of the selected MDCT coefficients that
carry the watermark bits, are saves in a database for future extraction
of the watermark. The proposed method is suitable for online MP3
stores to pursue illegal copies of musical artworks. Experimental
results show that the detection ratio of the watermarks at the bitrate
of 128kbps remains above 90% while the inaudibility of the
watermark is preserved.
Abstract: Speckle phenomena results from when coherent
radiation is reflected from a rough surface. Characterizing the speckle
strongly depends on the measurement condition and experimental
setup. In this paper we report the experimental results produced with
different parameters in the setup. We investigated the factors which
affects the speckle contrast, such as, F-number, gamma value and
exposure time of the camera, rather than geometric factors like the
distance between the projector lens to the screen, the viewing distance,
etc. The measurement results show that the speckle contrast decreases
by decreasing F-number, by increasing gamma value, and slightly
affects by exposure time of the camera and the gain value of the
camera.
Abstract: This paper discusses the performance modeling and availability analysis of Yarn Dyeing System of a Textile Industry. The Textile Industry is a complex and repairable engineering system. Yarn Dyeing System of Textile Industry consists of five subsystems arranged in series configuration. For performance modeling and analysis of availability, a performance evaluating model has been developed with the help of mathematical formulation based on Markov-Birth-Death Process. The differential equations have been developed on the basis of Probabilistic Approach using a Transition Diagram. These equations have further been solved using normalizing condition in order to develop the steady state availability, a performance measure of the system concerned. The system performance has been further analyzed with the help of decision matrices. These matrices provide various availability levels for different combinations of failure and repair rates for various subsystems. The findings of this paper are therefore, considered to be useful for the analysis of availability and determination of the best possible maintenance strategies which can be implemented in future to enhance the system performance.
Abstract: The purpose of this study is to understand how
consumers react to a company's promotional offers with mobile
applications (APP) as premiums. This paper presents the results of an
experimental study where five features of APP were involved: the
cost (free/discounted) for earning APP, the relationship between APP
and the promoted product, the perceived usefulness, the perceived
ease of use, and the perceived playfulness of APP in the context of
light foods purchase. The results support that the above features,
except perceived ease of use, have substantial influences on
consumers' intention to adopt the APP. Among the five features, the
cost for earning APP has the most impact on the adopting intention
of APP. The study also found a positive influence of adopting
intention of APP on the consumer's purchase intention of the
promoted product. Thus, APP-based premiums may enhance the
consumer's purchase intention of a company's promoted products.