Abstract: Nonstandard tests are necessary for analyses and
verification of new developed structural and technological solutions
with application of composite materials. One of the most critical
primary structural parts of a typical aerospace structure is T-joint.
This structural element is loaded mainly in shear, bending, peel and
tension. The paper is focused on the shear loading simulations. The
aim of the work is to obtain a representative uniform distribution of
shear loads along T-joint during the mechanical testing. A new
design of T-joint test procedure, numerical simulation and
optimization of representative boundary conditions are presented.
The different conditions and inaccuracies both in simulations and
experiments are discussed. The influence of different parameters on
stress and strain distributions is demonstrated on T-joint made of
CFRP (carbon fibre reinforced plastic). A special test rig designed by
VZLU (Aerospace Research and Test Establishment) for T-shear test
procedure is presented.
Abstract: This paper considers the characterization of a complex
electromagnetic environment due to multiple sources of
electromagnetic radiation as a five-dimensional surface which can be
described by a set of several surface sections including: instant EM
field intensity distribution maps at a given frequency and altitude,
instantaneous spectrum at a given location in space and the time
evolution of the electromagnetic field spectrum at a given point in
space. This characterization if done over time can enable the
exposure levels of Radio Frequency Radiation at every point in the
analysis area to be determined and results interpreted based on
comparison of the determined RFR exposure level with the safe
guidelines for general public exposure given by recognized body
such as the International commission on non-ionizing radiation
protection (ICNIRP), Institute of Electrical and Electronic Engineers
(IEEE), the National Radiation Protection Authority (NRPA).
Abstract: Different strategies and tools are available at the oil
and gas industry for detecting and analyzing tension and possible
fractures in borehole walls. Most of these techniques are based on
manual observation of the captured borehole images. While this
strategy may be possible and convenient with small images and few
data, it may become difficult and suitable to errors when big
databases of images must be treated. While the patterns may differ
among the image area, depending on many characteristics (drilling
strategy, rock components, rock strength, etc.). In this work we
propose the inclusion of data-mining classification strategies in order
to create a knowledge database of the segmented curves. These
classifiers allow that, after some time using and manually pointing
parts of borehole images that correspond to tension regions and
breakout areas, the system will indicate and suggest automatically
new candidate regions, with higher accuracy. We suggest the use of
different classifiers methods, in order to achieve different knowledge
dataset configurations.
Abstract: This paper is concerning the issues of behaviour of
lightweight expanded clay aggregates concrete exposed to high
temperature. Lightweight aggregates from expanded clay are
produced by firing of row material up to temperature 1050°C.
Lightweight aggregates have suitable properties in terms of volume
stability, when exposed to temperatures up to 1050°C, which could
indicate their suitability for construction applications with higher risk
of fire. The test samples were exposed to heat by using the standard
temperature-time curve ISO 834. Negative changes in resulting
mechanical properties, such as compressive strength, tensile strength,
and flexural strength were evaluated. Also visual evaluation of the
specimen was performed. On specimen exposed to excessive heat, an
explosive spalling could be observed, due to evaporation of
considerable amount of unbounded water from the inner structure of
the concrete.
Abstract: In this paper, thick walled Cylindrical tanks or tubes
made of functionally graded material under internal pressure and
temperature gradient are studied. Material parameters have been
considered as power functions. They play important role in the
elastoplastic behavior of these materials. To clarify their role,
different materials with different parameters have been used under
temperature gradient. Finally, their effect and loading effect have
been determined in first yield point. Also, the important role of
temperature gradient was also shown. At the end the study has been
results obtained from changes in the elastic modulus and yield stress.
Also special attention is also given to the effects of this internal
pressure and temperature gradient in the creation of tensile and
compressive stresses.
Abstract: This research focuses on the optimization of glazed
surfaces and the assessment of possible solar gains in industrial
buildings. Existing window rating methods for single windows were
evaluated and a new method for a simple analysis of energy gains and
losses by single windows was introduced. Furthermore extensive
transient building simulations were carried out to appraise the
performance of low cost polycarbonate multi-cell sheets in
interaction with typical buildings for industrial applications. Mainly
energy saving potential was determined by optimizing the orientation
and area of such glazing systems in dependency on their thermal
qualities. Moreover the impact on critical aspects such as summer
overheating and daylight illumination was considered to ensure the
user comfort and avoid additional energy demand for lighting or
cooling. Hereby the simulated heating demand could be reduced by
up to 1/3 compared to traditional architecture of industrial halls using
mainly skylights.
Abstract: Polyethylene (PE), Polypropylene (PP), Polyethylene
(vinyl acetate) (EVA) and PE-ionomer nanocomposite samples were
prepared by mixing of the polymer with organofilized
montmorillonite fillers Cloisite 93A and Dellite 67G. The amount of
each modified montmorillonite (MMT) was fixed to 5% (w/w). The
twin-screw kneader was used for the compounding of polymer matrix
and chosen nanofillers. The level of MMT exfoliation was studied by
the transmission electron microscopy (TEM) observations. The
mechanical properties of prepared materials were evaluated by
dynamical mechanical analysis at 30°C and by the measurement of
tensile properties (stress and strain at break).
Abstract: This paper attempts to evaluate the effect of fire
damage on concrete by using nonlinear resonance vibration method,
one of the nonlinear nondestructive method. Concrete exhibits not
only nonlinear stress-strain relation but also hysteresis and discrete
memory effect which are contained in consolidated materials.
Hysteretic materials typically show the linear resonance frequency
shift. Also, the shift of resonance frequency is changed according to
the degree of micro damage. The degree of the shift can be obtained
through nonlinear resonance vibration method. Five exposure
scenarios were considered in order to make different internal micro
damage. Also, the effect of post-fire-curing on fire-damaged concrete
was taken into account to conform the change in internal damage.
Hysteretic nonlinearity parameter was obtained by amplitudedependent
resonance frequency shift after specific curing periods. In
addition, splitting tensile strength was measured on each sample to
characterize the variation of residual strength. Then, a correlation
between the hysteretic nonlinearity parameter and residual strength
was proposed from each test result.
Abstract: Well-designed composite steel and concrete structures
highlight the good material properties and lower the deficiencies of
steel and concrete, in particular they make use of high tensile strength
of steel and high stiffness of concrete. The most common composite
steel and concrete structure is a simply supported beam, which
concrete slab transferring the slab load to a beam is connected to the
steel cross-section. The aim of this paper is to find the most adequate
numerical model of a simply supported composite beam with the
cross-sectional and material parameters based on the results of a
processed parametric study and numerical analysis. The paper also
evaluates the suitability of using compact concrete with the
lightweight aggregates for composite steel and concrete beams. The
most adequate numerical model will be used in the resent future to
compare the results of laboratory tests.
Abstract: Metal-enhanced Luminescence of silicon nanocrystals
(SiNCs) was determined using two different particle sizes of silver
nanoparticles (AgNPs). SiNCs have been characterized by scanning
electron microscopy (SEM), high resolution transmission electron
microscopy (HRTEM), Fourier transform infrared spectroscopy
(FTIR) and X-ray photoelectron spectroscopy (XPS). It is found that
the SiNCs are crystalline with an average diameter of 65 nm and FCC
lattice. AgNPs were synthesized using photochemical reduction of
AgNO3 with sodium dodecyl sulphate (SDS). The enhanced
luminescence of SiNCs by AgNPs was evaluated by confocal Raman
microspectroscopy. Enhancement up to x9 and x3 times were
observed for SiNCs that mixed with AgNPs which have an average
particle size of 100 nm and 30 nm, respectively. Silver NPs-enhanced
luminescence of SiNCs occurs as a result of the coupling between the
excitation laser light and the plasmon bands of AgNPs; thus this
intense field at AgNPs surface couples strongly to SiNCs.
Abstract: Copper being one of the major intrinsic residual
impurities in steel possesses the tendency to induce severe
microstructural distortions if not controlled within certain limits.
Hence, this paper investigates the effect of this element on the
mechanical properties of construction steel with a view to ascertain
its safe limits for effective control. The experiment entails collection
of statistically scheduled samples of hot rolled profiles with varied
copper concentrations in the range of 0.12-0.39 wt. %. From these
samples were prepared standard test specimens subjected to tensile,
impact, hardness and microstructural analyses. Results show a rather
huge compromise in mechanical properties as the specimens
demonstrated 54.3%, 74.2% and 64.9% reduction in tensile strength,
impact energy and hardness respectively as copper content increases
from 0.12 wt. % to 0.39 wt. %. The steel’s abysmal performance is
due to the severe distortion of the microstructure occasioned by the
development of incoherent complex compounds which weaken the
pearlite reinforcing phase. It is concluded that the presence of copper
above 0.22 wt. % is deleterious to construction steel performance.
Abstract: An anthropometric study applied to 1,115 students of
the Faculty of Chemical Sciences and Engineering of the
Autonomous University of California. Thirteen individual
measurements were taken in a sitting position. The results obtained
allow forming a reliable anthropometric database for statistical
studies and analysis and inferences of specific distributions, so the
opinion of experts in occupational medicine recommendations may
emit to reduce risks resulting in an alteration of the vital signs during
the execution of their school activities. Another use of these analyses
is to use them as a reliable reference for future deeper research, to the
design of spaces, tools, utensils, workstations, with anthropometric
dimensions and ergonomic characteristics suitable to use.
Abstract: Access control is one of the most challenging issues
facing information security. Access control is defined as, the ability to
permit or deny access to a particular computational resource or digital
information by an unauthorized user or subject. The concept of usage
control (UCON) has been introduced as a unified approach to capture a
number of extensions for access control models and systems. In
UCON, an access decision is determined by three factors:
authorizations, obligations and conditions. Attribute mutability and
decision continuity are two distinct characteristics introduced by
UCON for the first time. An observation of UCON components
indicates that, the components are predefined and static. In this paper,
we propose a new and flexible model of usage control for the creation
and elimination of some of these components; for example new
objects, subjects, attributes and integrate these with the original
UCON model. We also propose a model for concurrent usage
scenarios in UCON.
Abstract: In this study, first thermoplastic composite materials
/plates that have high ballistic impact resistance were produced. For
this purpose, the thermoplastic prepreg and the vacuum bagging
technique were used to produce a composite material. Thermoplastic
prepregs (resin-impregnated fiber) that are supplied ready to be used,
namely high-density polyethylene (HDPE) was chosen as matrix and
unidirectional glass fiber was used as reinforcement. In order to
compare the fiber configuration effect on mechanical properties,
unidirectional and biaxial prepregs were used. Then the
microstructural properties of the composites were investigated with
scanning electron microscopy (SEM) analysis. Impact properties of
the composites were examined by Charpy impact test and tensile
mechanical tests and then the effects of ultraviolet irradiation were
investigated on mechanical performance.
Abstract: Currently, biological control programs in greenhouse
crops involve the use, at the same time, several natural enemies
during the crop cycle. Also, large number of plant species grown in
greenhouses, among them, the used cultivars are also wide. However,
the cultivar effects on entomophagous species efficacy (predators and
parasitoids) have been scarcely studied. A new method had been
developed, using the factitious prey or host Ephestia kuehniella. It
allow us to evaluate, under greenhouse or controlled conditions
(semi-field), the cultivar effects on the entomophagous species
effectiveness. The work was carried out in greenhouse tomato crop. It
has been found the biological and ecological activities of predatory
species (Nesidiocoris tenuis) and egg-parasitoid (Trichogramma
achaeae) can be well represented with the use of the factitious prey
or host; being better in the former than the latter. The data found in
the trial are shown and discussed. The developed method could be
applied to evaluate new plant materials before making available to
farmers as commercial varieties, at low costs and easy use.
Abstract: The most important part of modern lean low NOx combustors is a premixer where swirlers are often used for intensification of mixing processes and further formation of required flow pattern in combustor liner. Swirling flow leads to formation of complex eddy structures causing flow perturbations. It is able to cause combustion instability. Therefore, at design phase, it is necessary to pay great attention to aerodynamics of premixers. Analysis based on unsteady CFD modeling of swirling flow in production combustor swirler showed presence of large number of different eddy structures that can be conditionally divided into three types relative to its location of origin and a propagation path. Further, features of each eddy type were subsequently defined. Comparison of calculated and experimental pressure fluctuations spectrums verified correctness of computations.
Abstract: Composite materials have important assets compared
to traditional materials. They bring many functional advantages:
lightness, mechanical resistance and chemical, etc. In the present
study we examine the effect of a circular central notch and a precrack
on the tensile fracture of two woven composite materials. The tensile
tests were applied to a standardized specimen, notched and a
precarcked (orientation of the crack 0°, 45° and 90°). These tensile
tests were elaborated according to an experimental planning design of
the type 23.31 requiring 24 experiments with three repetitions. By the
analysis of regression, we obtained a mathematical model describing
the maximum load according to the influential parameters (hole
diameter, precrack length, angle of a precrack orientation). The
specimens precracked at 90° have a better behavior than those having
a precrack at 45° and still better than those having of the precracks
oriented at 0°. In addition the maximum load is inversely
proportional to the notch size.
Abstract: The paper discusses economic policy of Georgia
aiming to increase national competitiveness as well as the tools and
means which will help to improve the competitiveness of the country.
The sectors of the economy, in which the country can achieve the
competitive advantage, are studied. It is noted that the country’s
economic policy plays an important role in obtaining and maintaining
the competitive advantage - authority should take measures to ensure
high level of education; scientific and research activities should be
funded by the state; foreign direct investments should be attracted
mainly in science-intensive industries; adaptation with the latest
scientific achievements of the modern world and deepening of
scientific and technical cooperation. Stable business environment and
export oriented strategy is the basis for the country’s economic
growth.
As the outcome of the research, the paper suggests the strategy for
improving competitiveness in Georgia; recommendations are
provided based on relevant conclusions.
Abstract: This paper clarifies the role of ICT capital in economic
growth. Albeit ICT remarkably contributes to economic growth, there
are few studies on ICT capital in ICT sector from theoretical point of
view. In this paper, production function of ICT which is used as input
of intermediate good in final good and ICT sectors is incorporated
into our model. In this setting, we analyze the role of ICT on balance
growth path and show the possibility of general equilibrium solutions
for this model. Through the simulation of the equilibrium solutions,
we find that when ICT impacts on economy and economic growth
increases, it is necessary that increases of efficiency at ICT sector and
of accumulation of non-ICT and ICT capitals occur simultaneously.
Abstract: From an organizational perspective, leaders are a
variation of the same talent pool in that they all score a larger than
average value on the bell curve that maps leadership behaviors and
characteristics, namely competence, vision, communication,
confidence, cultural sensibility, stewardship, empowerment,
authenticity, reinforcement, and creativity. The question that remains
unanswered and essentially unresolved is how to explain the irony
that leaders are so much alike yet their organizations diverge so
noticeably in their ability to innovate. Leadership intersects with
innovation at the point where human interactions get exceedingly
complex and where certain paradoxical forces cohabit: conflict with
conciliation, sovereignty with interdependence, and imagination with
realism. Rather than accepting that leadership is without context, we
argue that leaders are specialists of their domain and that those
effective at leading for innovation are distinct within the broader pool
of leaders. Keeping in view the extensive literature on leadership and
innovation, we carried out a quantitative study with data collected
over a five-year period involving 240 participants from across five
dissimilar companies based in the United States. We found that while
innovation and leadership are, in general, strongly interrelated (r =
.89, p = 0.0), there are five qualities that set leaders apart on
innovation. These qualities include a large radius of trust, a restless
curiosity with a low need for acceptance, an honest sense of self and
other, a sense for knowledge and creativity as the yin and yang of
innovation, and an ability to use multiple senses in the engagement
with followers. When these particular behaviors and characteristics
are present in leaders, organizations out-innovate their rivals by a
margin of 29.3 per cent to gain an unassailable edge in a business
environment that is regularly disruptive. A strategic outcome of this
study is a psychometric scale named iLeadership, proposed with the
underlying evidence, limitations, and potential for leadership and
innovation in organizations.c