Abstract: Compatibility between sulfonated acetone- formalehyde superplasticizer (SAF) and copolymer-based grinding aids (GA) were studied by fluidity, Zeta potential, setting time of cement pasts, initial slump and slump flow of concrete and compressive strength of concrete. ESEM, MIP, and XRD were used to investigate the changing of microstructure of interior concrete. The results indicated that GA could noticeably enhance the dispersion ability of SAF. It was found that better fluidity and slump-keeping ability of cement paste were obtained in the case of GA. In addition, GA together with SAF had a certain retardation effect on hydration of cement paste. With increasing of the GA dosage, the dispersion ability and retardation effect of admixture increased. The compressive strength of the sample made with SAF and GA after 28 days was higher than that of the control sample made only with SAF. The initial slump and slump flow of concrete increased by 10.0% and 22.9%, respectively, while 0.09 wt.% GA was used. XRD examination indicated that new products were not found in the case of GA. In addition, more dense arrangement of hydrates and lower porosity of the specimen were observed by ESEM and MIP, which contributed to higher compressive strength.
Abstract: Reconfigurable antennas represent a recent innovation in antenna design that changes from classical fixed-form, fixed function antennas to modifiable structures that can be adapted to fit the requirements of a time varying system.
The ability to control the operating band of an antenna system can have many useful applications. Systems that operate in an acquire-and-track configuration would see a benefit from active bandwidth control. In such systems a wide band search mode is first employed to find a desired signal then a narrow band track mode is used to follow only that signal. Utilizing active antenna bandwidth control, a single antenna would function for both the wide band and narrow band configurations providing the rejection of unwanted signals with the antenna hardware. This ability to move a portion of the RF filtering out of the receiver and onto the antenna itself will also aid in reducing the complexity of the often expensive RF processing subsystems.
Abstract: This paper proposes a way of removing noises and reducing the number of colors contained in a JPEG image. Main purpose of this project is to convert color images to monochrome images for the color-blind. We treat the crispy color images like the Tokyo subway map. Each color in the image has an important information. But for the color blinds, similar colors cannot be distinguished. If we can convert those colors to different gray values, they can distinguish them. Therefore we try to convert color images to monochrome images.
Abstract: An experimental study was conducted to investigate the effect of hooked-end steel fibers on the flexural behavior of normal and high strength concrete matrices. The fibers content appropriate for the concrete matrices investigated was also determined based on flexural tests on standard prisms. Parameters investigated include: matrix compressive strength ranging from 45 MPa to 70 MPa, corresponding to normal and high strength concrete matrices respectively; fibers volume fraction including 0, 0.5%, 0.76% and 1%, equivalent to 0, 40, 60, and 80 kg/m3 of hooked-end steel fibers respectively. Test results indicated that flexural strength and toughness of normal and high strength concrete matrices were significantly improved with the increase in the fibers content added; whereas a slight improvement in compressive strength was observed for the same matrices. Furthermore, the test results indicated that the effect of increasing the fibers content was more pronounced on increasing the flexural strength of high strength concrete than that of normal concrete.
Abstract: In this research, the changes in bubbles diameter and
number that may occur due to the change in heat flux of pure water
during pool boiling process. For this purpose, test equipment was
designed and developed to collect test data. The bubbles were graded
using Caliper Screen software. To calculate the growth and
nucleation rates of bubbles under different fluxes, population balance
model was employed. The results show that the increase in heat flux
from q=20 kw/m2 to q= 102 kw/m2 raised the growth and nucleation
rates of bubbles.
Abstract: In this study, two kinds of nondestructive evaluation
(NDE) techniques (rebound hardness and ultrasonic pulse velocity
methods) are investigated for the effective maintenance of underwater
concrete structures. A new methodology to estimate the underwater
concrete strengths more effectively, named “artificial neural network
(ANN) – based concrete strength estimation with the combination of
rebound hardness and ultrasonic pulse velocity methods” is proposed
and verified throughout a series of experimental works.
Abstract: Service quality is the highest requirement by users,
especially for the service in electronic government. During the past
decades, it has become a major area of academic investigation.
Considering this issue, there are a lot of researches that evaluated the
dimensions and e-service contexts. This study also identified the
dimensions of service quality, but focuses on a new concept and
provides a new methodology in developing measurement scales of
e-service quality such as information quality, service quality and
organization quality. Finally, this study will suggest a key factor to
evaluate e-government service quality better.
Abstract: Bone Anchored Hearing Implants (BAHI) are
routinely used in patients with conductive or mixed hearing loss, e.g.
if conventional air conduction hearing aids cannot be used. New
sound processors and new fitting software now allow the adjustment
of parameters such as loudness compression ratios or maximum
power output separately. Today it is unclear, how the choice of these
parameters influences aided speech understanding in BAHI users.
In this prospective experimental study, the effect of varying the
compression ratio and lowering the maximum power output in a
BAHI were investigated.
Twelve experienced adult subjects with a mixed hearing loss
participated in this study. Four different compression ratios (1.0; 1.3;
1.6; 2.0) were tested along with two different maximum power output
settings, resulting in a total of eight different programs. Each
participant tested each program during two weeks. A blinded Latin
square design was used to minimize bias.
For each of the eight programs, speech understanding in quiet and
in noise was assessed. For speech in quiet, the Freiburg number test
and the Freiburg monosyllabic word test at 50, 65, and 80 dB SPL
were used. For speech in noise, the Oldenburg sentence test was
administered.
Speech understanding in quiet and in noise was improved
significantly in the aided condition in any program, when compared
to the unaided condition. However, no significant differences were
found between any of the eight programs. In contrast, on a subjective
level there was a significant preference for medium compression
ratios of 1.3 to 1.6 and higher maximum power output.
Abstract: A two-dimensional linear wave-body interaction problem can be solved using a desingularized integral method by placing free surface Rankine sources over calm water surface and satisfying boundary conditions at prescribed collocation points on the
calm water surface. A new free-surface Rankine source distribution scheme, determined by the intersection points of free surface and body surface, is developed to reduce numerical computation cost. Associated with this, a new treatment is given to the intersection point. The present scheme results are in good agreement with traditional numerical results and measurements.
Abstract: Fuel rod analysis program transient (FRAPTRAN)
code was used to study the fuel rod performance during a postulated
large break loss of coolant accident (LBLOCA) in Maanshan nuclear
power plant (NPP). Previous transient results from thermal hydraulic
code, TRACE, with the same LBLOCA scenario, were used as input
boundary conditions for FRAPTRAN. The simulation results showed
that the peak cladding temperatures and the fuel centerline
temperatures were all below the 10CFR50.46 LOCA criteria. In
addition, the maximum hoop stress was 18 MPa and the oxide
thickness was 0.003mm for the present simulation cases, which are all
within the safety operation ranges. The present study confirms that this
analysis method, the FRAPTRAN code combined with TRACE, is an
appropriate approach to predict the fuel integrity under LBLOCA with
operational ECCS.
Abstract: We consider nonlinear uncertain systems such that a
priori information of the uncertainties is not available. For such
systems, we assume that the upper bound of the uncertainties is
represented as a Fredholm integral equation of the first kind and we
propose an adaptation law that is capable of estimating the upper
bound and design a continuous robust control which renders nonlinear
uncertain systems ultimately bounded.
Abstract: In this paper the intelligent control of full automatic car wash using a programmable logic controller (PLC) has been investigated and designed to do all steps of carwashing. The Intelligent control of full automatic carwash has the ability to identify and profile the geometrical dimensions of the vehicle chassis. Vehicle dimension identification is an important point in this control system to adjust the washing brushes position and time duration. The study also tries to design a control set for simulating and building the automatic carwash. The main purpose of the simulation is to develop criteria for designing and building this type of carwash in actual size to overcome challenges of automation. The results of this research indicate that the proposed method in process control not only increases productivity, speed, accuracy and safety but also reduce the time and cost of washing based on dynamic model of the vehicle. A laboratory prototype based on an advanced intelligent control has been built to study the validity of the design and simulation which it’s appropriate performance confirms the validity of this study.
Abstract: Grinding requires high specific energy and the consequent development of high temperature at tool-workpiece contact zone impairs workpiece quality by inducing thermal damage to the surface. Finishing grinding process requires component to be cut more than one pass. This paper deals with an investigation on the effect of multipass cutting on grinding performance in term of surface roughness and surface defect. An experimental set-up has been developed for this and a detailed comparison has been done with a single pass and various numbers of cutting pass. Results showed that surface roughness increase with the increase in a number of cutting pass. Good surface finish of 0.26μm was obtained for single pass cutting and 0.73μm for twenty pass cutting. It was also observed that the thickness of the white layer increased with the increased in a number of cutting pass.
Abstract: The development of new construction materials using
recycled plastic is important to both the construction and the plastic
recycling industries. Manufacturing of fibers from industrial or
postconsumer plastic waste is an attractive approach with such
benefits as concrete performance enhancement, and reduced needs
for land filling. The main objective of this study is to investigate the
effect of Plastic fibers obtained locally from recycled waste on plastic
shrinkage cracking of ordinary cement based mortar. Parameters
investigated include: fiber length ranging from 20 to 50mm, and fiber
volume fraction ranging from 0% to 1.5% by volume. The test results
showed significant improvement in crack arresting mechanism and
substantial reduction in the surface area of cracks for the mortar
reinforced with recycled plastic fibers compared to plain mortar.
Furthermore, test results indicated that there was a slight decrease in
compressive strength of mortar reinforced with different lengths and
contents of recycled fibers compared to plain mortar. This study
suggests that adding more than 1% of RP fibers to mortar, can be
used effectively for controlling plastic shrinkage cracking of cement
based mortar, and thus results in waste reduction and resources
conservation.
Abstract: Market institutions extension within transit societies
contributes to constituting the new type of middle class and
households livelihood strategies. The middle class households as an
example of prosperity in many cases encourage the ordinary ones to
do the same economic actions. Therefore, practices of using market
institutions by middle class households in transit societies, which are
mostly characterized by huge influence of traditional attitudes, can
carry habitual features for the whole society. Market institutions
consumption habit of the middle class households makes them
trendsetters of economic habits of other households while adapting to
the market economy. Moreover different social-economic positions
of households lead them to different consuming results such as
worsening or improving household economy due to indebtedness.
Abstract: This study is conducted to investigate the disparity of between learning styles and cognitive abilities specifically in Vocational Education. Felder and Silverman Learning Styles Model (FSLSM) was applied to measure the students’ learning styles while the content in Building Construction Subject consists; knowledge, skills and problem solving were taken into account in constructing the elements of cognitive abilities. Building Construction is one of the vocational courses offered in Vocational Education structure. There are four dimension of learning styles proposed by Felder and Silverman intended to capture student learning preferences with regards to processing either active or reflective, perception based on sensing or intuitive, input of information used visual or verbal and understanding information represent with sequential or global learner. Felder-Solomon Learning Styles Index was developed based on FSLSM and the questions were used to identify what type of student learning preferences. The index consists 44 item-questions characterize for learning styles dimension in FSLSM. The achievement test was developed to determine the students’ cognitive abilities. The quantitative data was analyzed in descriptive and inferential statistic involving Multivariate Analysis of Variance (MANOVA). The study discovered students are tending to be visual learners and each type of learner having significant difference whereas cognitive abilities there are different finding for each type of learners in knowledge, skills and problem solving. This study concludes the gap between type of learner and the cognitive abilities in few illustrations and it explained how the connecting made. The finding may help teachers to facilitate students more effectively and to boost the student’s cognitive abilities.
Abstract: This paper introduces an open-source software package SCILAB [1], an alternative of MATLAB [2], which can be used for robust control design and analysis of a typical mass-spring-damper (MSD) system. Using the previously published ideas in [3,4], this popular mechanical system is considered to provide another example of usefulness of SCILAB for advanced control design.
Abstract: Progressive collapse of buildings typically occurs
when abnormal loading conditions cause local damages, which leads
to a chain reaction of failure and ultimately catastrophic collapse. The
tie force (TF) method is one of the main design approaches for
progressive collapse. As the TF method is a simplified method, further
investigations on the reliability of the method is necessary. This study
aims to develop an improved TF method to design the cross wall
structures for progressive collapse. To this end, the pullout behavior of
strands in grout was firstly analyzed; and then, by considering the tie
force-slip relationship in the friction stage together with the catenary
action mechanism, a comprehensive analytical method was developed.
The reliability of this approach is verified by the experimental results
of concrete block pullout tests and full scale floor-to-floor joints tests
undertaken by Portland Cement Association (PCA). Discrepancies in
the tie force between the analytical results and codified specifications
have suggested the deficiency of TF method, hence an improved
model based on the analytical results has been proposed to address this
concern.
Abstract: This paper was prepared to see the perceptions of online lectures regarding collaborative learning, in terms of how lecturers view online collaborative learning in the higher learning institution. The purpose of this study was conducted to determine the perceptions of online lectures about collaborative learning, especially how lecturers see online collaborative learning in the university. Adult learning education enhance collaborative learning culture with the target of involving learners in the learning process to make teaching and learning more effective and open at the university. This will finally make students learning that will assist each other. It is also to cut down the pressure of loneliness and isolation might felt among adult learners. Their ways in collaborative online was also determined. In this paper, researchers collect data using questionnaires instruments. The collected data were analyzed and interpreted. By analyzing the data, researchers report the results according the proof taken from the respondents. Results from the study, it is not only dependent on the lecturer but also a student to shape a good collaborative learning practice. Rational concepts and pattern to achieve these targets be clear right from the beginning and may be good seen by a number of proposals submitted and include how the higher learning institution has trained with ongoing lectures online. Advantages of online collaborative learning show that lecturers should be trained effectively. Studies have seen that the lecturer aware of online collaborative learning. This positive attitude will encourage the higher learning institution to continue to give the knowledge and skills required.
Abstract: This article deals with the carbon nanotubes (CNT) synthesized from a novel precursor, sugar cane and Anodic Aluminum Oxide (AAO). The objective was to produce CNTs to be used as catalyst supports for Proton Exchange Membranes. The influence of temperature, inert gas flow rate and concentration of the precursor is presented. The CNTs prepared were characterized using TEM, XRD, Raman Spectroscopy, and the surface area determined by BET. The results show that it is possible to form CNT from sugar cane by pyrolysis and the CNTs are the type multi-walled carbon nanotubes. The MWCNTs are short and closed at the two ends with very small surface area of SBET= 3.691m,/g.