Abstract: Electronic nose (array of chemical sensors) are widely
used in food industry and pollution control. Also it could be used to
locate or detect the direction of the source of emission odors. Usually
this task is performed by electronic nose (ENose) cooperated with
mobile vehicles, but when a source is instantaneous or surrounding is
hard for vehicles to reach, problem occurs. Thus a method for
stationary ENose to detect the direction of the source and locate the
source will be required. A novel method which uses the ratio between
the responses of different sensors as a discriminant to determine the
direction of source in natural wind surroundings is presented in this
paper. The result shows that the method is accurate and easily to be
implemented. This method could be also used in movably, as an
optimized algorithm for robot tracking source location.
Abstract: The peel of dragon fruit is a byproduct left over after consuming. Normally, the use of plants as antioxidant source must be dried before further process. Therefore, the aim of this study is interesting to dry the peel by heat pump dryer (45 ºC) and fluidized bed dryer (110 º C) compared with the sun drying method. The sample with initial moisture content of about 85-91% wet basis was dried down to about 10% wet basis where it took 620 and 25 min for heat pump dryer and fluidized bed dryer, respectively. However, the sun drying took about 900 min to dry the peel. After that, sample was evaluated antioxidant activity, -carotene and betalains contents. The results found that the antioxidant activity and betalains contents of dried peel obtained from heat pump and fluidized bed dryings were significantly higher than that sun drying (p 0.05). Moreover, the drying by heat pump provided the highest -carotene content.
Abstract: Robust nonlinear integrated navigation of GPS and
low cost MEMS is a hot topic of research these days. A robust filter
is required to cope up with the problem of unpredictable
discontinuities and colored noises associated with low cost sensors.
H∞ filter is previously used in Extended Kalman filter and Unscented
Kalman filter frame. Unscented Kalman filter has a problem of
Cholesky matrix factorization at each step which is a very unstable
operation. To avoid this problem in this research H∞ filter is
designed in Square root Unscented filter framework and found 50%
more robust towards increased level of colored noises.
Abstract: In this paper a polymer electrolyte membrane (PEM)
fuel cell power system including burner, steam reformer, heat
exchanger and water heater has been considered to meet the
electrical, heating, cooling and domestic hot water loads of
residential building which in Tehran. The system uses natural gas as
fuel and works in CHP mode. Design and operating conditions of a
PEM fuel cell system is considered in this study. The energy
requirements of residential building and the number of fuel cell
stacks to meet them have been estimated. The method involved
exergy analysis and entropy generation thorough the months of the
year. Results show that all the energy needs of the building can be
met with 12 fuel cell stacks at a nominal capacity of 8.5 kW. Exergy
analysis of the CHP system shows that the increase in the ambient air
temperature from 1oC to 40oC, will have an increase of entropy
generation by 5.73%.Maximum entropy generates for 15 hour in 15th
of June and 15th of July is estimated to amount at 12624 (kW/K).
Entropy generation of this system through a year is estimated to
amount to 1004.54 GJ/k.year.
Abstract: Evolvable hardware (EHW) refers to a selfreconfiguration
hardware design, where the configuration is under
the control of an evolutionary algorithm (EA). A lot of research has
been done in this area several different EA have been introduced.
Every time a specific EA is chosen for solving a particular problem,
all its components, such as population size, initialization, selection
mechanism, mutation rate, and genetic operators, should be selected
in order to achieve the best results. In the last three decade a lot of
research has been carried out in order to identify the best parameters
for the EA-s components for different “test-problems". However
different researchers propose different solutions. In this paper the
behaviour of mutation rate on (1+λ) evolution strategy (ES) for
designing logic circuits, which has not been done before, has been
deeply analyzed. The mutation rate for an EHW system modifies
values of the logic cell inputs, the cell type (for example from AND
to NOR) and the circuit output. The behaviour of the mutation has
been analyzed based on the number of generations, genotype
redundancy and number of logic gates used for the evolved circuits.
The experimental results found provide the behaviour of the mutation
rate to be used during evolution for the design and optimization of
logic circuits. The researches on the best mutation rate during the last
40 years are also summarized.
Abstract: Conventional industrial monitoring systems are
tedious, inefficient and the at times integrity of the data is
unreliable. The objective of this system is to monitor industrial
processes specifically the fluid level which will measure the
instantaneous fluid level parameter and respond by text
messaging the exact value of the parameter to the user when
being enquired by a privileged access user. The development of
the embedded program code and the circuit for fluid level
measuring are discussed as well. Suggestions for future
implementations and efficient remote monitoring works are
included.
Abstract: In this paper, the implementation of low power,
high throughput convolutional filters for the one dimensional
Discrete Wavelet Transform and its inverse are presented. The
analysis filters have already been used for the implementation of a
high performance DWT encoder [15] with minimum memory
requirements for the JPEG 2000 standard. This paper presents the
design techniques and the implementation of the convolutional filters
included in the JPEG2000 standard for the forward and inverse DWT
for achieving low-power operation, high performance and reduced
memory accesses. Moreover, they have the ability of performing
progressive computations so as to minimize the buffering between
the decomposition and reconstruction phases. The experimental
results illustrate the filters- low power high throughput characteristics
as well as their memory efficient operation.
Abstract: This paper describes the development of a WLAN
propagation model, using Spectral Analyzer measurements. The
signal is generated by two Access Points (APs) on the base floor at
the administrative Communication School of ESPOL building. In
general, users do not have a Q&S reference about a wireless network;
however, this depends on the level signal as a function of frequency,
distance and other path conditions between receiver and transmitter.
Then, power density of the signal decrease as it propagates through
space and data transfer rate is affected. This document evaluates and
implements empirical mathematical formulation for the
characterization of WLAN radio wave propagation on two aisles of
the building base floor.
Abstract: High pressure adsorption of carbon dioxide on zeolite
13X was investigated in the pressure range (0 to 4) Mpa and
temperatures 298, 308 and 323K. The data fitting is accomplished
with the Toth, UNILAN, Dubinin-Astakhov and virial adsorption
models which are generally used for micro porous adsorbents such as
zeolites. Comparison with experimental data from the literature
indicated that the virial model would best determine results. These
results may be partly attributed to the flexibility of the virial model
which can accommodate as many constants as the data warrants.
Abstract: An experimental investigation was performed on pulp
liquid flow in straight ducts with a square cross section. Fully
developed steady flow was visualized and the fiber concentration was
obtained using a light-section method developed by the author et al.
The obtained results reveal quantitatively, in a definite form, the
distribution of the fiber concentration. From the results and
measurements of pressure loss, it is found that the flow characteristics
of pulp liquid in ducts can be classified into five patterns. The
relationships among the distributions of mean and fluctuation of fiber
concentration, the pressure loss and the flow velocity are discussed,
and then the features for each pattern are extracted. The degree of
nonuniformity of the fiber concentration, which is indicated by the
standard deviation of its distribution, is decreased from 0.3 to 0.05
with an increase in the velocity of the tested pulp liquid from 0.4 to
0.8%.
Abstract: This paper proposes a solution to the motion planning
and control problem of car-like mobile robots which is required to
move safely to a designated target in a priori known workspace
cluttered with swarm of boids exhibiting collective emergent
behaviors. A generalized algorithm for target convergence and
swarm avoidance is proposed that will work for any number of
swarms. The control laws proposed in this paper also ensures
practical stability of the system. The effectiveness of the proposed
control laws are demonstrated via computer simulations of an
emergent behavior.
Abstract: Recently, the health of retired National Football
League players, particularly lineman has been investigated. A number of studies have reported increased cardiometabolic risk, premature ardiovascular disease and incidence of type 2 diabetes. Rugby union players have somatotypes very similar
to National Football league players which suggest that rugby players may have similar health risks. The International Golden Oldies World Rugby Festival (GORF) provided a
unique opportunity to investigate the demographics of veteran rugby players. METHODOLOGIES: A cross-sectional, observational study was completed using an online web-based
questionnaire that consisted of medical history and
physiological measures. Data analysis was completed using a one sample t-test (50yrs) and Chi-square test. RESULTS: A total of 216 veteran rugby competitors
(response rate = 6.8%) representing 10 countries, aged 35-72 yrs (mean 51.2, S.D. ±8.0), participated in the online survey. As a group, the incidence of current smokers was low at 8.8%
(avg 72.4 cigs/wk) whilst the percentage consuming alcohol
was high (93.1% (avg 11.2 drinks/wk). Competitors reported
the following top six chronic diseases/disorders; hypertension
(18.6%), arthritis (OA/RA, 11.5%), asthma (9.3%),
hyperlipidemia (8.2%), diabetes (all types, 7.5%) and gout (6%), there were significant differences between groups with
regard to cancer (all types) and migraines. When compared to
the Australian general population (Australian Bureau of Statistics data, n=18,000), GORF competitors had a
Climstein Mike, Walsh Joe (corresponding author) and Burke Stephen
School of Exercise Science, Australian Catholic University, 25A Barker Road,
Strathfield, Sydney, NSW, 2016, Australia (e-mail:
[email protected], [email protected],
[email protected]).
John Best is with Orthosports, 160 Belmore Rd., Randwick, Sydney,NSW
2031, Australia (e-mail: [email protected]).
Heazlewood, Ian Timothy is with School of Environmental and Life
Sciences, Faculty Education, Health and Science, Charles Darwin University,
Precinct Yellow Building 2, Charles Darwin University, NT 0909, Australia
(e-mail: [email protected]).
Kettunen Jyrki Arcada University of Applied Sciences, Jan-Magnus
Janssonin aukio 1, FI-00550, Helsinki, Finland (e-mail:
[email protected]).
Adams Kent is with California State University Monterey Bay, Kinesiology Department, 100 Campus Center, Seaside, CA., 93955, USA (email: [email protected]).
DeBeliso Mark is with Department of Physical Education and Human
Performance, Southern Utah University, 351 West University Blvd, Cedar
City, Utah, USA (e-mail: [email protected]).
significantly lower incidence of anxiety (p
Abstract: Subdivision surfaces were applied to the entire
meshes in order to produce smooth surfaces refinement from coarse
mesh. Several schemes had been introduced in this area to provide a
set of rules to converge smooth surfaces. However, to compute and
render all the vertices are really inconvenient in terms of memory
consumption and runtime during the subdivision process. It will lead
to a heavy computational load especially at a higher level of
subdivision. Adaptive subdivision is a method that subdivides only at
certain areas of the meshes while the rest were maintained less
polygons. Although adaptive subdivision occurs at the selected areas,
the quality of produced surfaces which is their smoothness can be
preserved similar as well as regular subdivision. Nevertheless,
adaptive subdivision process burdened from two causes; calculations
need to be done to define areas that are required to be subdivided and
to remove cracks created from the subdivision depth difference
between the selected and unselected areas. Unfortunately, the result
of adaptive subdivision when it reaches to the higher level of
subdivision, it still brings the problem with memory consumption.
This research brings to iterative process of adaptive subdivision to
improve the previous adaptive method that will reduce memory
consumption applied on triangular mesh. The result of this iterative
process was acceptable better in memory and appearance in order to
produce fewer polygons while it preserves smooth surfaces.
Abstract: In this paper, with the purpose of further reducing the
complexity of the system, while keeping its temporal and spatial
focusing performance, we investigate the possibility of using optimal
one bit time reversal (TR) system for impulse radio ultra wideband
multi-user wireless communications. The results show that, by optimally
selecting the number of used taps in the pre-filter the optimal
one bit TR system can outperform the full one bit TR system. In
some cases, the temporal and spatial focusing performance of the
optimal one bit TR system appears to be compatible with that of the
original TR system. This is a significant result as the overhead cost
is much lower than it is required in the original TR system.
Abstract: Inventory decisional environment of short life-cycle
products is full of uncertainties arising from randomness and
fuzziness of input parameters like customer demand requiring
modeling under hybrid uncertainty. Prior inventory models
incorporating fuzzy demand have unfortunately ignored stochastic
variation of demand. This paper determines an unambiguous optimal
order quantity from a set of n fuzzy observations in a newsvendor
inventory setting in presence of fuzzy random variable demand
capturing both fuzzy perception and randomness of customer
demand. The stress of this paper is in providing solution procedure
that attains optimality in two steps with demand information
availability in linguistic phrases leading to fuzziness along with
stochastic variation. The first step of solution procedure identifies
and prefers one best fuzzy opinion out of all expert opinions and the
second step determines optimal order quantity from the selected
event that maximizes profit. The model and solution procedure is
illustrated with a numerical example.
Abstract: Cavitation, usually known as a destructive
phenomenon, involves turbulent unsteady two-phase flow. Having
such features, cavitating flows have been turned to a challenging
topic in numerical studies and many researches are being done for
better understanding of bubbly flows and proposing solutions to
reduce its consequent destructive effects. Aeration may be regarded
as an effective protection against cavitation erosion in many
hydraulic structures, like gated tunnels. The paper concerns
numerical simulation of flow in discharge gated tunnel of a dam
using ing RNG k -ε model coupled with the volume of fluid (VOF)
method and the zone which is susceptible of cavitation inception in
the tunnel is predicted. In the second step, a vent is considered in the
mentioned zone for aeration and the numerical simulation is done
again to study the effects of aeration. The results show that aeration
is an impressively useful method to exclude cavitation in mentioned
tunnels.
Abstract: This paper proposes an alternative control mechanism
for an interactive Pan/Tilt/Zoom (PTZ) camera control system.
Instead of using a mouse or a joystick, the proposed mechanism
utilizes a Nintendo Wii remote and infrared (IR) sensor bar. The Wii
remote has buttons that allows the user to control the movement of a
PTZ camera through Bluetooth connectivity. In addition, the Wii
remote has a built-in motion sensor that allows the user to give
control signals to the PTZ camera through pitch and roll movement.
A stationary IR sensor bar, placed at some distance away opposite the
Wii remote, enables the detection of yaw movement. In addition, the
Wii remote-s built-in IR camera has the ability to detect its spatial
position, and thus generates a control signal when the user moves the
Wii remote. Some experiments are carried out and their performances
are compared with an industry-standard PTZ joystick.
Abstract: In the Lost Foam Casting process, melting point
temperature of metal, as well as volume and rate of the foam
degradation have significant effect on the mold filling pattern.
Therefore, gas generation capacity and gas gap length are two
important parameters for modeling of mold filling time of the lost
foam casting processes. In this paper, the gas gap length at the liquidfoam
interface for a low melting point (aluminum) alloy and a high
melting point (Carbon-steel) alloy are investigated by the
photography technique. Results of the photography technique
indicated, that the gas gap length and the mold filling time are
increased with increased coating thickness and density of the foam.
The Gas gap lengths measured in aluminum and Carbon-steel,
depend on the foam density, and were approximately 4-5 and 25-60
mm, respectively. By using a new system, the gas generation
capacity for the aluminum and steel was measured. The gas
generation capacity measurements indicated that gas generation in
the Aluminum and Carbon-steel lost foam casting was about 50 CC/g
and 3200 CC/g polystyrene, respectively.
Abstract: Clustering algorithms are attractive for the task of class identification in spatial databases. However, the application to large spatial databases rises the following requirements for clustering algorithms: minimal requirements of domain knowledge to determine the input parameters, discovery of clusters with arbitrary shape and good efficiency on large databases. The well-known clustering algorithms offer no solution to the combination of these requirements. In this paper, a density based clustering algorithm (DCBRD) is presented, relying on a knowledge acquired from the data by dividing the data space into overlapped regions. The proposed algorithm discovers arbitrary shaped clusters, requires no input parameters and uses the same definitions of DBSCAN algorithm. We performed an experimental evaluation of the effectiveness and efficiency of it, and compared this results with that of DBSCAN. The results of our experiments demonstrate that the proposed algorithm is significantly efficient in discovering clusters of arbitrary shape and size.
Abstract: This work discusses an innovative methodology for
deployment of service quality characteristics. Four groups of organizational features that may influence the quality of services are identified: human resource, technology, planning, and organizational
relationships. A House of Service Quality (HOSQ) matrix is built to
extract the desired improvement in the service quality characteristics
and to translate them into a hierarchy of important organizational
features. The Mean Square Error (MSE) criterion enables the
pinpointing of the few essential service quality characteristics to be
improved as well as selection of the vital organizational features. The
method was implemented in an engineering supply enterprise and
provides useful information on its vital service dimensions.