Abstract: In this study a two dimensional axisymmetric, steady state and incompressible laminar flow in a rotating single disk is numerically investigated. The finite volume method is used for solving the momentum equations. The numerical model and results
are validated by comparing it to previously reported experimental data for velocities, angles and moment coefficients. It is
demonstrated that increasing the axial distance increases the value of axial velocity and vice versa for tangential and total velocities. However, the maximum value of nondimensional radial velocity
occurs near the disk wall. It is also found that with increase rotational Reynolds number, moment coefficient decreases.
Abstract: Coagulation of water involves the use of coagulating
agents to bring the suspended matter in the raw water together for
settling and the filtration stage. Present study is aimed to examine the
effects of aluminum sulfate as coagulant in conjunction with Moringa
Oleifera Coagulant Protein as coagulant aid on turbidity, hardness,
and bacteria in turbid water. A conventional jar test apparatus was
employed for the tests. The best removal was observed at a pH of 7
to 7.5 for all turbidities. Turbidity removal efficiency was resulted
between % 80 to % 99 by Moringa Oleifera Coagulant Protein as
coagulant aid. Dosage of coagulant and coagulant aid decreased with
increasing turbidity. In addition, Moringa Oleifera Coagulant Protein
significantly has reduced the required dosage of primary coagulant.
Residual Al+3 in treated water were less than 0.2 mg/l and meets the
environmental protection agency guidelines. The results showed that
turbidity reduction of % 85.9- % 98 paralleled by a primary
Escherichia coli reduction of 1-3 log units (99.2 – 99.97%) was
obtained within the first 1 to 2 h of treatment. In conclusions,
Moringa Oleifera Coagulant Protein as coagulant aid can be used for
drinking water treatment without the risk of organic or nutrient
release. We demonstrated that optimal design method is an efficient
approach for optimization of coagulation-flocculation process and
appropriate for raw water treatment.
Abstract: Located within the tropical belt region, there are
certain rules which should implemented in creating a passive
sustainable housing design in Malaysia. Traditional Malay house
possess a strong character with certain special spaces to create a
sustainable house which suit to the tropical climate in Malaysia. One
of the special space known as verandah or serambi gantung, create
various advantages in solving various issues. However, this special
space is not extremely being applied currently which produce major
issues in term of social and environmental aspects. Hence, this
phenomena create a negative impact to the occupant while Malaysia
already has a best housing design previously. Therefore, this paper
aims to explore both of the main issues mentioned above and reveal
the advantages of implementing verandah into passive sustainable
housing design in Malaysia. A systematic literature review is the
main methodology in this research to identify the various advantages
about verandah.. The study reveals that verandah is the best solution
in term of social and environmental issues and should be
implemented in current housing design in Malaysia.
Abstract: The restoration of extinct ponds is considered as one
of ways to gain new retention capacities for water which is getting
much more important issue with respect to expected impacts of a
climate change. However, there are also other pressures on the
landscape which must be all taken into consideration when making a
decision on the possible restoration of extinct ponds. The research
presented here focuses besides others on the restoration of former
ponds which could be important for both the flood protection and
drought impacts prevention. The first step of the methodology
development for the assessment of such areas is the assessment of
their present state. In this paper, the results of land use types
assessment for 22 localities are presented. These results confirm the
assumption that the most present land use type in such areas is the
permanent grassland. However, the spectra of land use types present
in extinct pond areas is very diverse and include besides others also
airport areas and industry.
Abstract: PCMs have always been viewed as a suitable
candidate for off peak thermal storage, particularly for refrigeration
systems, due to the high latent energy densities of these materials.
However, due to the need to have them encapsulated within a
container this density is reduced. Furthermore, PCMs have a low
thermal conductivity which reduces the useful amount of energy
which can be stored. To consider these factors, the true energy
storage density of a PCM system was proposed and optimised for
PCMs encapsulated in slabs. Using a validated numerical model of
the system, a parametric study was undertaken to investigate the
impact of the slab thickness, gap between slabs and the mass flow
rate. The study showed that, when optimised, a PCM system can
deliver a true energy storage density between 53% and 83% of the
latent energy density of the PCM.
Abstract: The traditional method for essential oil extraction from agarwood (Aquilaria Crassna) is to soak it in water and follow with hydrodistillation. The effect of various agarwood pretreatments: ethanol, acid, alkaline, enzymes, and ultrasound, and the effect of subcritical water extraction(SWE) was studied to compare with the traditional method. The major compositions of agarwood oil from hydrodistillation were aroma compounds as follow: aristol-9-en-8- one (21.53%), selina-3, 7(11)-diene (12.96%), τ-himachalene (9.28%), β-guaiene (5.79%), hexadecanoic acid (4.90%) and guaia- 3,9-diene (4.21%). Whereas agarwood oil from pretreatments with ethanol and ultrasound, and SWE got fatty acid compounds. Extraction of agarwood oil using these pretreatments could improve the agarwood oil yields up to 2 times that of the traditional method. The components of the pretreated sample with diluted acid (H2SO4) at pH 4 gave quite similar results as the traditional method. Therefore, the enhancement of essential oil from agarwood depends on requirement of type of extracted oil that involved extraction methods.
Abstract: Image data holds a large amount of different context
information. However, as of today, these resources remain largely
untouched. It is thus the aim of this paper to present a basic technical
framework which allows for a quick and easy exploitation of context
information from image data especially by non-expert users.
Furthermore, the proposed framework is discussed in detail
concerning important social and ethical issues which demand special
requirements in system design. Finally, a first sensor prototype is
presented which meets the identified requirements. Additionally,
necessary implications for the software and hardware design of the
system are discussed, rendering a sensor system which could be
regarded as a good, acceptable and justifiable technical and thereby
enabling the extraction of context information from image data.
Abstract: Process-oriented software development is a new
software development paradigm in which software design is modeled
by a business process which is in turn translated into a process
execution language for execution. The building blocks of this
paradigm are software units that are composed together to work
according to the flow of the business process. This new paradigm
still exhibits the characteristic of the applications built with the
traditional software component technology. This paper discusses an
approach to apply a traditional technique for software component
fabrication to the design of process-oriented software units, called
process components. These process components result from
decomposing a business process of a particular application domain
into subprocesses, and these process components can be reused to
design the business processes of other application domains. The
decomposition considers five managerial goals, namely cost
effectiveness, ease of assembly, customization, reusability, and
maintainability. The paper presents how to design or decompose
process components from a business process model and measure
some technical features of the design that would affect the
managerial goals. A comparison between the measurement values
from different designs can tell which process component design is
more appropriate for the managerial goals that have been set. The
proposed approach can be applied in Web Services environment
which accommodates process-oriented software development.
Abstract: High Speed PM Generators driven by micro-turbines
are widely used in Smart Grid System. So, this paper proposes
comparative study among six classical, optimized and genetic
analytical design cases for 400 kW output power at tip speed 200
m/s. These six design trials of High Speed Permanent Magnet
Synchronous Generators (HSPMSGs) are: Classical Sizing;
Unconstrained optimization for total losses and its minimization;
Constrained optimized total mass with bounded constraints are
introduced in the problem formulation. Then a genetic algorithm is
formulated for obtaining maximum efficiency and minimizing
machine size. In the second genetic problem formulation, we attempt
to obtain minimum mass, the machine sizing that is constrained by
the non-linear constraint function of machine losses. Finally, an
optimum torque per ampere genetic sizing is predicted. All results are
simulated with MATLAB, Optimization Toolbox and its Genetic
Algorithm. Finally, six analytical design examples comparisons are
introduced with study of machines waveforms, THD and rotor losses.
Abstract: This paper presents preliminary results of a
technology assessment analysis for the use of high pressure treatment
(HPT) on Halloumi cheese. In particular, it presents the importance
of this traditional Cyprus cheese to the island-s economy, explains its
production process, and gives a brief introduction to HPT and its
application on cheese. More importantly, it offers preliminary results
of HPT of Halloumi samples and a preliminary economic feasibility
study on the financial implications of the introduction of such
technology.
Abstract: One of the main environmental problems which affect extensive areas in the world is soil salinity. Traditional data collection methods are neither enough for considering this important environmental problem nor accurate for soil studies. Remote sensing data could overcome most of these problems. Although satellite images are commonly used for these studies, however there are still needs to find the best calibration between the data and real situations in each specified area. Neyshaboor area, North East of Iran was selected as a field study of this research. Landsat satellite images for this area were used in order to prepare suitable learning samples for processing and classifying the images. 300 locations were selected randomly in the area to collect soil samples and finally 273 locations were reselected for further laboratory works and image processing analysis. Electrical conductivity of all samples was measured. Six reflective bands of ETM+ satellite images taken from the study area in 2002 were used for soil salinity classification. The classification was carried out using common algorithms based on the best composition bands. The results showed that the reflective bands 7, 3, 4 and 1 are the best band composition for preparing the color composite images. We also found out, that hybrid classification is a suitable method for identifying and delineation of different salinity classes in the area.
Abstract: A numerical analysis of wave and hydrodynamic models
is used to investigate the influence of WAve and Storm Surge
(WASS) in the regional and coastal zones. The numerical analyzed
system consists of the WAve Model Cycle 4 (WAMC4) and the
Princeton Ocean Model (POM) which used to solve the energy
balance and primitive equations respectively. The results of both
models presented the incorporated surface wave in the regional
zone affected the coastal storm surge zone. Specifically, the results
indicated that the WASS generally under the approximation is not
only the peak surge but also the coastal water level drop which
can also cause substantial impact on the coastal environment. The
wave–induced surface stress affected the storm surge can significantly
improve storm surge prediction. Finally, the calibration of wave
module according to the minimum error of the significant wave height
(Hs) is not necessarily result in the optimum wave module in the
WASS analyzed system for the WASS prediction.
Abstract: Support Vector Machine (SVM) is a recent class of statistical classification and regression techniques playing an increasing role in applications to detection problems in various engineering problems, notably in statistical signal processing, pattern recognition, image analysis, and communication systems. In this paper, SVM is applied to an infrared (IR) binary communication system with different types of channel models including Ricean multipath fading and partially developed scattering channel with additive white Gaussian noise (AWGN) at the receiver. The structure and performance of SVM in terms of the bit error rate (BER) metric is derived and simulated for these channel stochastic models and the computational complexity of the implementation, in terms of average computational time per bit, is also presented. The performance of SVM is then compared to classical binary signal maximum likelihood detection using a matched filter driven by On-Off keying (OOK) modulation. We found that the performance of SVM is superior to that of the traditional optimal detection schemes used in statistical communication, especially for very low signal-to-noise ratio (SNR) ranges. For large SNR, the performance of the SVM is similar to that of the classical detectors. The implication of these results is that SVM can prove very beneficial to IR communication systems that notoriously suffer from low SNR at the cost of increased computational complexity.
Abstract: In the context of sensor networks, where every few
dB saving counts, the novel node cooperation schemes are reviewed
where MIMO techniques play a leading role. These methods could be
treated as joint approach for designing physical layer of their
communication scenarios. Then we analyzed the BER performance
of transmission diversity schemes under a general fading channel
model and proposed a power allocation strategy to the transmitting
sensor nodes. This approach is then compared to an equal-power
assignment method and its performance enhancement is verified by
the simulation. Another key point of the contribution lies in the
combination of optimal power allocation and sensor nodes-
cooperation in a transmission diversity regime (MISO). Numerical
results are given through figures to demonstrate the optimality and
efficiency of proposed combined approach.
Abstract: Coated tool inserts can be considered as the backbone
of machining processes due to their wear and heat resistance.
However, defects of coating can degrade the integrity of these inserts
and the number of these defects should be minimized or eliminated if
possible. Recently, the advancement of coating processes and
analytical tools open a new era for optimizing the coating tools.
First, an overview is given regarding coating technology for cutting
tool inserts. Testing techniques for coating layers properties, as well
as the various coating defects and their assessment are also surveyed.
Second, it is introduced an experimental approach to examine the
possible coating defects and flaws of worn multicoated carbide
inserts using two important techniques namely scanning electron
microscopy and atomic force microscopy. Finally, it is
recommended a simple procedure for investigating manufacturing
defects and flaws of worn inserts.
Abstract: This paper presents a formant-tracking linear prediction
(FTLP) model for speech processing in noise. The main focus of this
work is the detection of formant trajectory based on Hidden Markov
Models (HMM), for improved formant estimation in noise. The
approach proposed in this paper provides a systematic framework for
modelling and utilization of a time- sequence of peaks which satisfies
continuity constraints on parameter; the within peaks are modelled
by the LP parameters. The formant tracking LP model estimation
is composed of three stages: (1) a pre-cleaning multi-band spectral
subtraction stage to reduce the effect of residue noise on formants
(2) estimation stage where an initial estimate of the LP model of
speech for each frame is obtained (3) a formant classification using
probability models of formants and Viterbi-decoders. The evaluation
results for the estimation of the formant tracking LP model tested
in Gaussian white noise background, demonstrate that the proposed
combination of the initial noise reduction stage with formant tracking
and LPC variable order analysis, results in a significant reduction in
errors and distortions. The performance was evaluated with noisy
natual vowels extracted from international french and English vocabulary
speech signals at SNR value of 10dB. In each case, the
estimated formants are compared to reference formants.
Abstract: The need to evaluate and understand the natural
drainage pattern in a flood prone, and fast developing environment is
of paramount importance. This information will go a long way to
help the town planners to determine the drainage pattern, road
networks and areas where prominent structures are to be located. This
research work was carried out with the aim of studying the Bayelsa
landscape topography using digitized topographic information, and to
model the natural drainage flow pattern that will aid the
understanding and constructions of workable drainages. To achieve
this, digitize information of elevation and coordinate points were
extracted from a global imagery map. The extracted information was
modeled into 3D surfaces. The result revealed that the average
elevation for Bayelsa State is 12 m above sea level. The highest
elevation is 28 m, and the lowest elevation 0 m, along the coastline.
In Yenagoa the capital city of Bayelsa were a detail survey was
carried out showed that average elevation is 15 m, the highest
elevation is 25 m and lowest is 3 m above the mean sea level. The
regional elevation in Bayelsa, showed a gradation decrease from the
North Eastern zone to the South Western Zone. Yenagoa showed an
observed elevation lineament, were low depression is flanked by high
elevation that runs from the North East to the South west. Hence,
future drainages in Yenagoa should be directed from the high
elevation, from South East toward the North West and from the
North West toward South East, to the point of convergence which is
at the center that flows from South East toward the North West.
Bayelsa when considered on a regional Scale, the flow pattern is from
the North East to the South West, and also North South. It is
recommended that in the event of any large drainage construction at
municipal scale, it should be directed from North East to the South
West or from North to South. Secondly, detail survey should be
carried out to ascertain the local topography and the drainage pattern
before the design and construction of any drainage system in any part
of Bayelsa.
Abstract: In this paper, we have proposed a low cost optimized solution for the movement of a three-arm manipulator using Genetic Algorithm (GA) and Analytical Hierarchy Process (AHP). A scheme is given for optimizing the movement of robotic arm with the help of Genetic Algorithm so that the minimum energy consumption criteria can be achieved. As compared to Direct Kinematics, Inverse Kinematics evolved two solutions out of which the best-fit solution is selected with the help of Genetic Algorithm and is kept in search space for future use. The Inverse Kinematics, Fitness Value evaluation and Binary Encoding like tasks are simulated and tested. Although, three factors viz. Movement, Friction and Least Settling Time (or Min. Vibration) are used for finding the Fitness Function / Fitness Values, however some more factors can also be considered.
Abstract: This paper introduces and studies new indexing techniques for content-based queries in images databases. Indexing is the key to providing sophisticated, accurate and fast searches for queries in image data. This research describes a new indexing approach, which depends on linear modeling of signals, using bases for modeling. A basis is a set of chosen images, and modeling an image is a least-squares approximation of the image as a linear combination of the basis images. The coefficients of the basis images are taken together to serve as index for that image. The paper describes the implementation of the indexing scheme, and presents the findings of our extensive evaluation that was conducted to optimize (1) the choice of the basis matrix (B), and (2) the size of the index A (N). Furthermore, we compare the performance of our indexing scheme with other schemes. Our results show that our scheme has significantly higher performance.
Abstract: Plastic waste is a big issue in Thailand, but the amount of recycled plastic in Thailand is still low due to the high investment and operating cost. Hence, the rest of plastic waste are burnt to destroy or sent to the landfills. In order to be financial viable, an effective reverse logistics infrastructure is required to support the product recovery activities. However, there is a conflict between reducing the cost and raising environmental protection level. The purpose of this study is to build a goal programming (GP) so that it can be used to help analyze the proper planning of the Thailand-s plastic recycling system that involves multiple objectives. This study considers three objectives; reducing total cost, increasing the amount of plastic recovery, and raising the desired plastic materials in recycling process. The results from two priority structures show that it is necessary to raise the total cost budget in order to achieve targets on amount of recycled plastic and desired plastic materials.