Abstract: Porcelain specimens were fired at 6C/min to 1250C (dwell time 0.5-3h) and cooled at 6C/min to room temperature. Additionally, three different slower firing/cooling cycles were tried. Sintering profile and effects on MOR, crystalline phase content and morphology were investigated using dilatometry, 4-point bending strength, XRD and FEG-SEM respectively. Industrial-sized specimens prepared using the promising cycle were tested basing on the ANSI standards. Increasing dwell time from 1h to 3h at peak temperature of 1250C resulted in neither a significant effect on the quartz and mullite content nor MOR. Reducing the firing/cooling rate to below 6C/min, for peak temperature of 1250C (dwell time of 1h) does not result in improvement of strength of porcelain. The industrial sized specimen exhibited flashover voltages of 20.3kV (dry) and 9.3kV (wet) respectively, transverse strength of 12.5kN and bulk density of 2.27g/cm3, which are satisfactory. There was however dye penetration during porosity test. KeywordsDwell time, Microstructure, Porcelain, Strength.
Abstract: Measuring the complexity of software has been an
insoluble problem in software engineering. Complexity measures can
be used to predict critical information about testability, reliability,
and maintainability of software systems from automatic analysis of
the source code. During the past few years, many complexity
measures have been invented based on the emerging Cognitive
Informatics discipline. These software complexity measures,
including cognitive functional size, lend themselves to the approach
of the total cognitive weights of basic control structures such as loops
and branches. This paper shows that the current existing calculation
method can generate different results that are algebraically
equivalence. However, analysis of the combinatorial meanings of this
calculation method shows significant flaw of the measure, which also
explains why it does not satisfy Weyuker's properties. Based on the
findings, improvement directions, such as measures fusion, and
cumulative variable counting scheme are suggested to enhance the
effectiveness of cognitive complexity measures.
Abstract: As a part of an evaluation system for R&D programs,
the Korean Government has applied the preliminary feasibility study
to new government R&D program plans. Basically, the fundamental purpose of the preliminary feasibility study is to decide that the
government will either do or do not invest in a new R&D Program. Additionally, the preliminary feasibility study can contribute to the
improvement of R&D program plans. For example, 2 cases of new
R&D program plans applied to the study are explained in this paper and there are expectations that these R&D programs would yield better
performance than without the study. It is thought that the important point of the preliminary feasibility study is not only the effective
decision making process of R&D program but also the opportunity to improve R&D program plan actually.
Abstract: This research studied about green logistics and the
expected benefit that organization gotten when adapted to green
logistics also the organization concerned about the important activity
in green logistics to apply in implementation from study was found
that the benefit of green logistics that organization was gotten by
logistics management which was the increased efficiency process of
management the product from producer to customer all of reduce
production cost, increased value added save energy and prevented
environment together
From study was found that the organization had green logistics to
apply in logistics activities in supply chain since downstream till
upstream to prevent environment as follow 1). Purchasing process,
trade facilitation enhance such as linking of information technology
during business to business (B2B business). 2). Productions process
improved by business logistics improvement 3). Warehouse
management process such as recycled packaging, moving goods in to
warehouse, transportation goods and inside receiving and delivery
products plan.
Abstract: Technological innovation capability (TIC) is
defined as a comprehensive set of characteristics of a firm that
facilities and supports its technological innovation strategies.
An audit to evaluate the TICs of a firm may trigger
improvement in its future practices. Such an audit can be used
by the firm for self assessment or third-party independent
assessment to identify problems of its capability status. This
paper attempts to develop such an auditing framework that
can help to determine the subtle links between innovation
capabilities and business performance; and to enable the
auditor to determine whether good practice is in place. The
seven TICs in this study include learning, R&D, resources
allocation, manufacturing, marketing, organization and
strategic planning capabilities. Empirical data was acquired
through a survey study of 200 manufacturing firms in the
Hong Kong/Pearl River Delta (HK/PRD) region. Structural
equation modelling was employed to examine the
relationships among TICs and various performance indicators:
sales performance, innovation performance, product
performance, and sales growth. The results revealed that
different TICs have different impacts on different
performance measures. Organization capability was found to
have the most influential impact. Hong Kong manufacturers
are now facing the challenge of high-mix-low-volume
customer orders. In order to cope with this change, good
capability in organizing different activities among various
departments is critical to the success of a company.
Abstract: Key management is a vital component in any modern security protocol. Due to scalability and practical implementation considerations automatic key management seems a natural choice in significantly large virtual private networks (VPNs). In this context IETF Internet Key Exchange (IKE) is the most promising protocol under permanent review. We have made a humble effort to pinpoint IKEv2 net gain over IKEv1 due to recent modifications in its original structure, along with a brief overview of salient improvements between the two versions. We have used US National Institute of Technology NIIST VPN simulator to get some comparisons of important performance metrics.
Abstract: This work deals with aspects of support vector machine learning for large-scale data mining tasks. Based on a decomposition algorithm for support vector machine training that can be run in serial as well as shared memory parallel mode we introduce a transformation of the training data that allows for the usage of an expensive generalized kernel without additional costs. We present experiments for the Gaussian kernel, but usage of other kernel functions is possible, too. In order to further speed up the decomposition algorithm we analyze the critical problem of working set selection for large training data sets. In addition, we analyze the influence of the working set sizes onto the scalability of the parallel decomposition scheme. Our tests and conclusions led to several modifications of the algorithm and the improvement of overall support vector machine learning performance. Our method allows for using extensive parameter search methods to optimize classification accuracy.
Abstract: As far as the latest technological improvements are concerned, digital systems more become popular than the past. Despite this growing demand to the digital systems, content copy and attack against the digital cinema contents becomes a serious problem. To solve the above security problem, we propose “traceable watermarking using Hash functions for digital cinema system. Digital Cinema is a great application for traceable watermarking since it uses watermarking technology during content play as well as content transmission. The watermark is embedded into the randomly selected movie frames using CRC-32 techniques. CRC-32 is a Hash function. Using it, the embedding position is distributed by Hash Function so that any party cannot break off the watermarking or will not be able to change. Finally, our experimental results show that proposed DWT watermarking method using CRC-32 is much better than the convenient watermarking techniques in terms of robustness, image quality and its simple but unbreakable algorithm.
Abstract: This paper presents a procedure for modeling and tuning the parameters of Thyristor Controlled Series Compensation (TCSC) controller in a multi-machine power system to improve transient stability. First a simple transfer function model of TCSC controller for stability improvement is developed and the parameters of the proposed controller are optimally tuned. Genetic algorithm (GA) is employed for the optimization of the parameter-constrained nonlinear optimization problem implemented in a simulation environment. By minimizing an objective function in which the oscillatory rotor angle deviations of the generators are involved, transient stability performance of the system is improved. The proposed TCSC controller is tested on a multi-machine system and the simulation results are presented. The nonlinear simulation results validate the effectiveness of proposed approach for transient stability improvement in a multimachine power system installed with a TCSC. The simulation results also show that the proposed TCSC controller is also effective in damping low frequency oscillations.
Abstract: Graph partitioning is a NP-hard problem with multiple
conflicting objectives. The graph partitioning should minimize the
inter-partition relationship while maximizing the intra-partition
relationship. Furthermore, the partition load should be evenly
distributed over the respective partitions. Therefore this is a multiobjective
optimization problem (MOO). One of the approaches to
MOO is Pareto optimization which has been used in this paper. The
proposed methods of this paper used to improve the performance are
injecting best solutions of previous runs into the first generation of
next runs and also storing the non-dominated set of previous
generations to combine with later generation's non-dominated set.
These improvements prevent the GA from getting stuck in the local
optima and increase the probability of finding more optimal
solutions. Finally, a simulation research is carried out to investigate
the effectiveness of the proposed algorithm. The simulation results
confirm the effectiveness of the proposed method.
Abstract: The lack of security obstructs a large scale de- ployment of the multicast communication model. There- fore, a host of research works have been achieved in order to deal with several issues relating to securing the multicast, such as confidentiality, authentication, non-repudiation, in- tegrity and access control. Many applications require au- thenticating the source of the received traffic, such as broadcasting stock quotes and videoconferencing and hence source authentication is a required component in the whole multicast security architecture. In this paper, we propose a new and efficient source au- thentication protocol which guarantees non-repudiation for multicast flows, and tolerates packet loss. We have simu- lated our protocol using NS-2, and the simulation results show that the protocol allows to achieve improvements over protocols fitting into the same category.
Abstract: Power Factor (PF) is one of the most important parameters in the electrical systems, especially in the water pumping station. The low power factor value of the water pumping stations causes penalty for the electrical bill. There are many methods use for power factor improvement. Each one of them uses a capacitor on the electrical power network. The position of the capacitors is varied depends on many factors such as; voltage level and capacitors rating. Adding capacitors on the motor terminals increase the supply power factor from 0.8 to more than 0.9 but these capacitors cause some problems for the electrical grid network, such as increasing the harmonic contents of the grid line voltage. In this paper the effects of using capacitors in the water pumping stations to improve the power factor value on the harmonic contents of the electrical grid network are studied. One of large water pumping stations in Kafr El-Shikh Governorate in Egypt was used, as a case study. The effect of capacitors on the line voltage harmonic contents is measured. The station uses capacitors to improve the PF values at the 1 lkv grid network. The power supply harmonics values are measured by a power quality analyzer at different loading conditions. The results showed that; the capacitors improved the power factor value of the feeder and its value increased than 0.9. But the THD values are increased by adding these capacitors. The harmonic analysis showed that; the 13th, 17th, and 19th harmonics orders are increased also by adding the capacitors.
Abstract: In this paper, we are going to determine the threshold levels of adaptive modulation in a burst by burst CDMA system by a suboptimum method so that the above method attempts to increase the average bit per symbol (BPS) rate of transceiver system by switching between the different modulation modes in variable channel condition. In this method, we choose the minimum values of average bit error rate (BER) and maximum values of average BPS on different values of average channel signal to noise ratio (SNR) and then calculate the relative threshold levels of them, so that when the instantaneous SNR increases, a higher order modulation be employed for increasing throughput and vise-versa when the instantaneous SNR decreases, a lower order modulation be employed for improvement of BER. In transmission step, by this adaptive modulation method, in according to comparison between obtained estimation of pilot symbols and a set of above suboptimum threshold levels, above system chooses one of states no transmission, BPSK, 4QAM and square 16QAM for modulation of data. The expected channel in this paper is a slow Rayleigh fading.
Abstract: The H.264/AVC video coding standard contains a number of advanced features. Ones of the new features introduced in this standard is the multiple intramode prediction. Its function exploits directional spatial correlation with adjacent block for intra prediction. With this new features, intra coding of H.264/AVC offers a considerably higher improvement in coding efficiency compared to other compression standard, but computational complexity is increased significantly when brut force rate distortion optimization (RDO) algorithm is used. In this paper, we propose a new fast intra prediction mode decision method for the complexity reduction of H.264 video coding. for luma intra prediction, the proposed method consists of two step: in the first step, we make the RDO for four mode of intra 4x4 block, based the distribution of RDO cost of those modes and the idea that the fort correlation with adjacent mode, we select the best mode of intra 4x4 block. In the second step, we based the fact that the dominating direction of a smaller block is similar to that of bigger block, the candidate modes of 8x8 blocks and 16x16 macroblocks are determined. So, in case of chroma intra prediction, the variance of the chroma pixel values is much smaller than that of luma ones, since our proposed uses only the mode DC. Experimental results show that the new fast intra mode decision algorithm increases the speed of intra coding significantly with negligible loss of PSNR.
Abstract: In countries with hot climates, air-conditioning forms
a large proportion of annual peak electrical demand, requiring
expansion of power plants to meet the peak demand, which goes
unused most of the time. Use of well-designed cool storage can offset
the peak demand to a large extent. In this study, an air conditioning
system with naturally stratified storage tank was designed,
constructed and tested. A new type of diffuser was designed and used
in this study. Factors that influence the performance of chilled water
storage tanks were investigated. The results indicated that stratified
storage tank consistently stratified well without any physical barrier.
Investigation also showed that storage efficiency decreased with
increasing flow rate due to increased mixing of warm and chilled
water. Diffuser design and layout primarily affected the mixing near
the inlet diffuser and the extent of this mixing had primary influence
on the shape of the thermocline. The heat conduction through tank
walls and through the thermocline caused widening of mixed volume.
Thermal efficiency of stratified storage tanks was as high as 90
percent, which indicates that stratified tanks can effectively be used
as a load management technique.
Abstract: We present a theory for optimal filtering of infinite sets of random signals. There are several new distinctive features of the proposed approach. First, we provide a single optimal filter for processing any signal from a given infinite signal set. Second, the filter is presented in the special form of a sum with p terms where each term is represented as a combination of three operations. Each operation is a special stage of the filtering aimed at facilitating the associated numerical work. Third, an iterative scheme is implemented into the filter structure to provide an improvement in the filter performance at each step of the scheme. The final step of the concerns signal compression and decompression. This step is based on the solution of a new rank-constrained matrix approximation problem. The solution to the matrix problem is described in this paper. A rigorous error analysis is given for the new filter.
Abstract: In this study we focus on improvement performance
of a cue based Motor Imagery Brain Computer Interface (BCI). For
this purpose, data fusion approach is used on results of different
classifiers to make the best decision. At first step Distinction
Sensitive Learning Vector Quantization method is used as a feature
selection method to determine most informative frequencies in
recorded signals and its performance is evaluated by frequency
search method. Then informative features are extracted by packet
wavelet transform. In next step 5 different types of classification
methods are applied. The methodologies are tested on BCI
Competition II dataset III, the best obtained accuracy is 85% and the
best kappa value is 0.8. At final step ordered weighted averaging
(OWA) method is used to provide a proper aggregation classifiers
outputs. Using OWA enhanced system accuracy to 95% and kappa
value to 0.9. Applying OWA just uses 50 milliseconds for
performing calculation.
Abstract: In order to provide accurate heart rate variability
indices of sympathetic and parasympathetic activity, the low
frequency and high frequency components of an RR heart rate signal
must be adequately separated. This is not always possible by just
applying spectral analysis, as power from the high and low frequency
components often leak into their adjacent bands. Furthermore,
without the respiratory spectra it is not obvious that the low
frequency component is not another respiratory component, which
can appear in the lower band. This paper describes an adaptive filter,
which aids the separation of the low frequency sympathetic and high
frequency parasympathetic components from an ECG R-R interval
signal, enabling the attainment of more accurate heart rate variability
measures. The algorithm is applied to simulated signals and heart rate
and respiratory signals acquired from an ambulatory monitor
incorporating single lead ECG and inductive plethysmography
sensors embedded in a garment. The results show an improvement
over standard heart rate variability spectral measurements.
Abstract: A data warehouse (DW) is a system which has value and role for decision-making by querying. Queries to DW are critical regarding to their complexity and length. They often access millions of tuples, and involve joins between relations and aggregations. Materialized views are able to provide the better performance for DW queries. However, these views have maintenance cost, so materialization of all views is not possible. An important challenge of DW environment is materialized view selection because we have to realize the trade-off between performance and view maintenance. Therefore, in this paper, we introduce a new approach aimed to solve this challenge based on Two-Phase Optimization (2PO), which is a combination of Simulated Annealing (SA) and Iterative Improvement (II), with the use of Multiple View Processing Plan (MVPP). Our experiments show that 2PO outperform the original algorithms in terms of query processing cost and view maintenance cost.
Abstract: An optimal control of Reverse Osmosis (RO) plant is
studied in this paper utilizing the auto tuning concept in conjunction
with PID controller. A control scheme composing an auto tuning
stochastic technique based on an improved Genetic Algorithm (GA) is
proposed. For better evaluation of the process in GA, objective
function defined newly in sense of root mean square error has been
used. Also in order to achieve better performance of GA, more
pureness and longer period of random number generation in operation
are sought. The main improvement is made by replacing the uniform
distribution random number generator in conventional GA technique
to newly designed hybrid random generator composed of Cauchy
distribution and linear congruential generator, which provides
independent and different random numbers at each individual steps in
Genetic operation. The performance of newly proposed GA tuned
controller is compared with those of conventional ones via simulation.