Abstract: Investigating the dynamic responses of high rise
structures under the effect of siesmic ground motion is extremely
important for the proper analysis and design of multitoried structures.
Since the presence of infilled walls strongly influences the behaviour
of frame systems in multistoried buildings, there is an increased need
for developing guidelines for the analysis and design of infilled
frames under the effect of dynamic loads for safe and proper design
of buildings. In this manuscript, we evaluate the natural frequencies
and natural periods of single bay single storey frames considering the
effect of infill walls by using the Eigen value analysis and validating
with SAP 2000 (free vibration analysis). Various parameters obtained
from the diagonal strut model followed for the free vibration analysis
is then compared with the Finite Element model, where infill is
modeled as shell elements (four noded). We also evaluated the effect
of various parameters on the natural periods of vibration obtained by
free vibration analysis in SAP 2000 comparing them with those
obtained by the empirical expressions presented in I.S. 1893(Part I)-
2002.
Abstract: Adequate analgesia following caesarean section
decreases morbidity, hastens ambulation, improves patient outcome
and facilitates care of the newborn. Intrathecal magnesium, an
NMDA antagonist, has been shown to prolong analgesia without
significant side effects in healthy parturients. The aim of this study
was to evaluate the onset and duration of sensory and motor block,
hemodynamic effect, postoperative analgesia, and adverse effects of
magnesium or fentanyl given intrathecally with hyperbaric 0.5%
bupivacaine in patients with mild preeclampsia undergoing caesarean
section. Sixty women with mild preeclampsia undergoing elective
caesarean section were included in a prospective, double blind,
controlled trial. Patients were randomly assigned to receive spinal
anesthesia with 2 mL 0.5% hyperbaric bupivacaine with 12.5 μg
fentanyl (group F) or 0.1 ml of 50% magnesium sulphate (50 mg)
(group M) with 0.15ml preservative free distilled water. Onset,
duration and recovery of sensory and motor block, time to maximum
sensory block, duration of spinal anaesthesia and postoperative
analgesic requirements were studied. Statistical comparison was
carried out using the Chi-square or Fisher’s exact tests and
Independent Student’s t-test where appropriate. The onset of both
sensory and motor block was slower in the magnesium group. The
duration of spinal anaesthesia (246 vs. 284) and motor block (186.3
vs. 210) were significantly longer in the magnesium group. Total
analgesic top up requirement was less in group M. Hemodynamic
parameters were similar in both the groups. Intrathecal magnesium
caused minimal side effects. Since Fentanyl and other opioid
congeners are not available throughout the country easily,
magnesium with its easy availability and less side effect profile can
be a cost effective alternative to fentanyl in managing pregnancy
induced hypertension (PIH) patients given along with Bupivacaine
intrathecally in caesarean section.
Abstract: In this article, a new method is proposed for the measuring of well-being inequality through a model composed of superimposing satisfaction waves. The displacement of households’ satisfactory state (i.e. satisfaction) is defined in a satisfaction string. The duration of the satisfactory state for a given period is measured in order to determine the relationship between utility and total satisfactory time, itself dependent on the density and tension of each satisfaction string. Thus, individual cardinal total satisfaction values are computed by way of a one-dimensional form for scalar sinusoidal (harmonic) moving wave function, using satisfaction waves with varying amplitudes and frequencies which allow us to measure wellbeing inequality. One advantage to using satisfaction waves is the ability to show that individual utility and consumption amounts would probably not commute; hence, it is impossible to measure or to know simultaneously the values of these observables from the dataset. Thus, we crystallize the problem by using a Heisenberg-type uncertainty resolution for self-adjoint economic operators. We propose to eliminate any estimation bias by correlating the standard deviations of selected economic operators; this is achieved by replacing the aforementioned observed uncertainties with households’ perceived uncertainties (i.e. corrected standard deviations) obtained through the logarithmic psychophysical law proposed by Weber and Fechner.
Abstract: The primary objective of this work was to study the
effect of resin chemistry, pH and molarity of binding and elution
buffer on aggregate removal using Cation Exchange Chromatography
and find the optimum conditions which can give efficient aggregate
removal with minimum loss of yield. Four different resins were used
for carrying out the experiments: Fractogel EMD SO3
-(S), Fractogel EMD COO-(M), Capto SP ImpRes and S Ceramic HyperD. Runs
were carried out on the AKTA Avant system. Design of Experiments
(DOE) was used for analysis using the JMP software. The
dependence of the yield obtained using different resins on the
operating conditions was studied. Success has been achieved in
obtaining yield greater than 90% using Capto SP ImpRes and
Fractogel EMD COO-(M) resins. It has also been found that a change
in the operating conditions generally has different effects on the
yields obtained using different resins.
Abstract: In the present paper the design of plate heat exchangers
is formulated as an optimization problem considering two
mathematical modelling. The number of plates is the objective
function to be minimized, considering implicitly some parameters
configuration. Screening is the optimization method used to solve the
problem. Thermal and hydraulic constraints are verified, not viable
solutions are discarded and the method searches for the convergence to
the optimum, case it exists. A case study is presented to test the
applicability of the developed algorithm. Results show coherency with
the literature.
Abstract: Multiple-input multiple-output (MIMO) radar has
received increasing attention in recent years. MIMO radar has many
advantages over conventional phased array radar such as target
detection,resolution enhancement, and interference suppression. In
this paper, the results are presented from a simulation study of MIMO
uniformly-spaced linear array (ULA) antennas. The performance is
investigated under varied parameters, including varied array size,
pseudo random (PN) sequence length, number of snapshots, and
signal to noise ratio (SNR). The results of MIMO are compared to a
traditional array antenna.
Abstract: The access to relevant information that is adapted to
user’s needs, preferences and environment is a challenge in many
applications running. That causes an appearance of context-aware
systems. To facilitate the development of this class of applications, it
is necessary that these applications share a common context
metamodel. In this article, we will present our context metamodel
that is defined using the OMG Meta Object facility (MOF).This
metamodel is based on the analysis and synthesis of context concepts
proposed in literature.
Abstract: Mobile Ad Hoc Networks (MANETs) is a collection
of mobile devices forming a communication network without
infrastructure. MANET is vulnerable to security threats due to
network’s limited security, dynamic topology, scalability and the lack
of central management. The Quality of Service (QoS) routing in such
networks is limited by network breakage caused by node mobility or
nodes energy depletions. The impact of node mobility on trust
establishment is considered and its use to propagate trust through a
network is investigated in this paper. This work proposes an
enhanced Associativity Based Routing (ABR) with Fuzzy based
Trust (Fuzzy- ABR) routing protocol for MANET to improve QoS
and to mitigate network attacks.
Abstract: In this paper numerical studies have been carried out
to examine the pre-ignition flow features of high-performance solid
propellant rocket motors with two different port geometries but with
same propellant loading density. Numerical computations have been
carried out using a validated 3D, unsteady, 2nd-order implicit, SST k-
ω turbulence model. In the numerical study, a fully implicit finite
volume scheme of the compressible, Reynolds-Averaged, Navier-
Stokes equations is employed. We have observed from the numerical
results that in solid rocket motors with highly loaded propellants
having divergent port geometry the hot igniter gases can create preignition
pressure oscillations leading to thrust oscillations due to the
flow unsteadiness and recirculation. We have also observed that the
igniter temperature fluctuations are diminished rapidly thereby
reaching the steady state value faster in the case of solid propellant
rocket motors with convergent port than the divergent port
irrespective of the igniter total pressure. We have concluded that the
prudent selection of the port geometry, without altering the propellant
loading density, for damping the total temperature fluctuations within
the motor is a meaningful objective for the suppression and control of
instability and/or thrust oscillations often observed in solid propellant
rocket motors with non-uniform port geometry.
Abstract: The increasing volume of solid waste generated,
collected and disposed daily complicate adequate management of
solid waste by relevant agency like Niger State Environmental
Protection Agency (NISEPA). In addition, the impacts of solid waste
on the natural environment and human livelihood require
identification of cost-effective ways for sustainable municipal waste
management in Nigeria. These signal the need for identifying
environment-friendly initiative and local solution to address the
problem of municipal solid waste. A research field was secured at
Pago, Minna, Niger State which is located in the guinea savanna belt
of Nigeria, within longitude 60 361 4311 - 4511 and latitude 90 291
37.6111 - .6211 N. Poultry droppings, decomposed household waste
manure and NPK treatments were used. The experimental field was
divided into three replications and four (4) treatments on each
replication making a total of twelve (12) plots. The treatments were
allotted using Randomized Complete Block Design (RCBD) and
Data collected was analyzed using SPSS software and RCBD. The
result depicts variation in plant height and number of leaves at 50%
flowering; Poultry dropping records the highest height while the
number of leaves for waste manure competes fairly well with NPK
treatment. Similarly, the varying treatments significantly increase
vegetable yield, as the control (non-treatment) records the least yield
for the three vegetable samples. Adoption of this organic manure for
cultivation does not only enhance environment quality and attainment
of food security but will contribute to local economic development,
poverty alleviation as well as social inclusion.
Abstract: The aim of the current work was to employ the finite
element method to model a slab, with a small hole across its width,
undergoing plastic plane strain deformation. The computational
model had, however, to be validated by comparing its results with
those obtained experimentally. Since they were in good agreement,
the finite element method can therefore be considered a reliable tool
that can help gain better understanding of the mechanism of ductile
failure in structural members having stress raisers. The finite element
software used was ANSYS, and the PLANE183 element was utilized.
It is a higher order 2-D, 8-node or 6-node element with quadratic
displacement behavior. A bilinear stress-strain relationship was used
to define the material properties, with constants similar to those of the
material used in the experimental study. The model was run for
several tensile loads in order to observe the progression of the plastic
deformation region, and the stress concentration factor was
determined in each case. The experimental study involved employing the visioplasticity
technique, where a circular mesh (each circle was 0.5 mm in
diameter, with 0.05 mm line thickness) was initially printed on the
side of an aluminum slab having a small hole across its width.
Tensile loading was then applied to produce a small increment of
plastic deformation. Circles in the plastic region became ellipses,
where the directions of the principal strains and stresses coincided
with the major and minor axes of the ellipses. Next, we were able to
determine the directions of the maximum and minimum shear
stresses at the center of each ellipse, and the slip-line field was then
constructed. We were then able to determine the stress at any point in
the plastic deformation zone, and hence the stress concentration
factor. The experimental results were found to be in good agreement
with the analytical ones.
Abstract: This survey paper shows the recent state of model
comparison as it’s applies to Model Driven engineering. In Model
Driven Engineering to calculate the difference between the models is
a very important and challenging task. There are number of tasks
involved in model differencing that firstly starts with identifying and
matching the elements of the model. In this paper, we discuss how
model matching is accomplished, the strategies, techniques and the
types of the model. We also discuss the future direction. We found
out that many of the latest model comparison strategies are geared
near enabling Meta model and similarity based matching. Therefore
model versioning is the most dominant application of the model
comparison. Recently to work on comparison for versioning has
begun to deteriorate, giving way to different applications. Ultimately
there is wide change among the tools in the measure of client exertion
needed to perform model comparisons, as some require more push to
encourage more sweeping statement and expressive force.
Abstract: A new design of aerostatic thrust bearing is proposed
for high static stiffness. The bearing body, which is mead of polymer
covered with metallic membrane, is held by a circular ring. Such a
support helps form a concave air gap to grasp the air pressure. The
polymer body, which can be made rapidly by either injection or
molding is able to provide extra damping under dynamic loading. The
smooth membrane not only serves as the bearing surface but also
protects the polymer body. The restrictor is a capillary inside a silicone
tube. It can passively compensate the variation of load by expanding
the capillary diameter for more air flux. In the present example, the
stiffness soars from 15.85 N/μm of typical bearing to 349.85 N/μm at
bearing elevation 9.5 μm; meanwhile the load capacity also enhances
from 346.86 N to 704.18 N.
Abstract: Traditional mechanical control systems in thrust
vectoring are efficient in rocket thrust guidance but their costs
and their weights are excessive. The fluidic injection in the nozzle
divergent constitutes an alternative procedure to achieve the goal. In
this paper, we present a 3D analytical model for fluidic injection
in a supersonic nozzle integrating an orifice. The fluidic vectoring
uses a sonic secondary injection in the divergent. As a result, the
flow and interaction between the main and secondary jet has built in
order to express the pressure fields from which the forces and thrust
vectoring are deduced. Under various separation criteria, the present
analytical model results are compared with the existing numerical
and experimental data from the literature.
Abstract: This paper presents a study on the effect of
second-order slip and jump on forced convection through a long
isothermally heated or cooled planar microchannel. The fully
developed solutions of thermal flow fields are analytically obtained on
the basis of the second-order Maxwell-Burnett slip and Smoluchowski
jump boundary conditions. Results reveal that the second-order term in
the Karniadakis slip boundary condition is found to contribute a
negative velocity slip and then to lead to a higher pressure drop as well
as a higher fluid temperature for the heated-wall case or to a lower
fluid temperature for the cooled-wall case. These findings are contrary
to predictions made by the Deissler model. In addition, the role of
second-order slip becomes more significant when the Knudsen
number increases.
Abstract: Concrete is strong in compression however weak in
tension. The tensile strength as well as ductile property of concrete
could be improved by addition of short dispersed fibers. Polyethylene
terephthalate (PET) fiber obtained from hand cutting or mechanical
slitting of plastic sheets generally used as discrete reinforcement in
substitution of steel fiber. PET fiber obtained from the former process
is in the form of straight slit sheet pattern that impart weaker
mechanical bonding behavior in the concrete matrix. To improve the
limitation of straight slit sheet fiber the present study considered two
additional geometry of fiber namely (a) flattened end slit sheet and
(b) deformed slit sheet. The mix for plain concrete was design for a
compressive strength of 25 MPa at 28 days curing time with a watercement
ratio of 0.5. Cylindrical and beam specimens with 0.5% fibers
volume fraction and without fibers were cast to investigate the
influence of geometry on the mechanical properties of concrete. The
performance parameters mainly studied include flexural strength,
splitting tensile strength, compressive strength and ultrasonic pulse
velocity (UPV). Test results show that geometry of fiber has a
marginal effect on the workability of concrete. However, it plays a
significant role in achieving a good compressive and tensile strength
of concrete. Further, significant improvement in term of flexural and
energy dissipation capacity were observed from other fibers as
compared to the straight slit sheet pattern. Also, the inclusion of PET
fiber improved the ability in absorbing energy in the post-cracking
state of the specimen as well as no significant porous structures.
Abstract: The goal of the modern education system is to prepare
students to be able to adapt to ever-changing life situations. They
must be able to acquire required knowledge independently; apply
such knowledge in practice to solve various problems by using
modern technologies; think critically and creatively; competently use
information; be communicative, work in a team; and develop their
own moral values, intellect and cultural awareness. As a result, the
status of education significantly increases; new requirements to its
quality have been formed. In recent years the competency-based
approach in education has become of significant interest. This
approach is a strengthening of applied and practical characteristics of
a school education and leads to the forming of the key students’
competencies which define their success in future life. In this article,
the authors’ attention focuses on a range of key competencies,
educational, informational and communicative and on the possibility
to develop such competencies via STEM education. This research
shows the change in students’ attitude towards scientific disciplines
such as mathematics, general science, technology and engineering as
a result of STEM education. Two staged analyzed questionnaires
completed by students of forms II to IV in the republic of Trinidad
and Tobago allowed the authors to categorize students between two
levels that represent students’ attitude to various disciplines. The
significance of differences between selected levels was confirmed
with the use of Pearson’s chi-squared test. In summary, the analysis
of obtained data makes it possible to conclude that STEM education
has a great potential for development of core students’ competencies
and encourage the development of positive student attitude towards
the above mentioned above scientific disciplines.
Abstract: This paper seeks to assess the implications of
insurance to foreign direct investment inflow in Nigeria. Multiple
linear regression technique and correlation matrix test were employed
to measure the extent to which foreign direct investment was
influenced. The result showed that insurance premium (IP), asset size
of insurance industry (AS), and total investment of the industry (TI)
impacted significantly and positively on foreign direct investment
inflow in Nigeria. There should be effective risk transfer mechanism
and financial intermediation, which gives the investor confidence in
the risk management strength of the host country.
Abstract: Electrohydraulic servo system have been used in
industry in a wide number of applications. Its dynamics are highly
nonlinear and also have large extent of model uncertainties and
external disturbances. In this paper, a robust back-stepping control
(RBSC) scheme is proposed to overcome the problem of disturbances
and system uncertainties effectively and to improve the tracking
performance of EHS systems. In order to implement the proposed
control scheme, the system uncertainties in EHS systems are
considered as total leakage coefficient and effective oil volume. In
addition, in order to obtain the virtual controls for stabilizing system,
the update rule for the system uncertainty term is induced by
the Lyapunov control function (LCF). To verify the performance and
robustness of the proposed control system, computer simulation of
the proposed control system using Matlab/Simulink Software
is executed. From the computer simulation, it was found that the
RBSC system produces the desired tracking performance and has
robustness to the disturbances and system uncertainties of EHS
systems.
Abstract: The teaching of computer programming for beginners
has been generally considered as a difficult and challenging task.
Several methodologies and research tools have been developed,
however, the difficulty of teaching still remains. Our work integrates
the state of the art in teaching programming with game software and
further provides metrics for the evaluation of student performance in
a collaborative activity of playing games. This paper aims to present a
multi-agent system architecture to be incorporated to the educational
collaborative game software for teaching programming that monitors,
evaluates and encourages collaboration by the participants. A
literature review has been made on the concepts of Collaborative
Learning, Multi-agents systems, collaborative games and techniques
to teach programming using these concepts simultaneously.