Abstract: In this paper a novel method for multiple one dimensional real valued sinusoidal signal frequency estimation in the presence of additive Gaussian noise is postulated. A computationally simple frequency estimation method with efficient statistical performance is attractive in many array signal processing applications. The prime focus of this paper is to combine the subspace-based technique and a simple peak search approach. This paper presents a variant of the Propagator Method (PM), where a collaborative approach of SUMWE and Propagator method is applied in order to estimate the multiple real valued sine wave frequencies. A new data model is proposed, which gives the dimension of the signal subspace is equal to the number of frequencies present in the observation. But, the signal subspace dimension is twice the number of frequencies in the conventional MUSIC method for estimating frequencies of real-valued sinusoidal signal. The statistical analysis of the proposed method is studied, and the explicit expression of asymptotic (large-sample) mean-squared-error (MSE) or variance of the estimation error is derived. The performance of the method is demonstrated, and the theoretical analysis is substantiated through numerical examples. The proposed method can achieve sustainable high estimation accuracy and frequency resolution at a lower SNR, which is verified by simulation by comparing with conventional MUSIC, ESPRIT and Propagator Method.
Abstract: Properties of cement pastes with fine-ground ceramics
used as an alternative binder replacing Portland cement up to 20% of
its mass are investigated. At first, the particle size distribution of
cement and fine-ground ceramics is measured using laser analyser.
Then, the material properties are studied in the early hardening
period up to 28 days. The hydration process of studied materials is
monitored by electrical conductivity measurement using TDR
sensors. The changes of materials- structures within the hardening are
observed using pore size distribution measurement. The compressive
strength measurements are done as well. Experimental results show
that the replacement of Portland cement by fine-ground ceramics in
the amount of up to 20% by mass is acceptable solution from the
mechanical point of view. One can also assume similar physical
properties of designed materials to the reference material with only
Portland cement as binder.
Abstract: A water surface slope limiting scheme is tested and
compared with the water depth slope limiter for the solution of one
dimensional shallow water equations with bottom slope source term.
Numerical schemes based on the total variation diminishing Runge-
Kutta discontinuous Galerkin finite element method with slope
limiter schemes based on water surface slope and water depth are
used to solve one-dimensional shallow water equations. For each
slope limiter, three different Riemann solvers based on HLL, LF, and
Roe flux functions are used. The proposed water surface based slope
limiter scheme is easy to implement and shows better conservation
property compared to the slope limiter based on water depth. Of the
three flux functions, the Roe approximation provides the best results
while the LF function proves to be least suitable when used with
either slope limiter scheme.
Abstract: Renewable water resources are crucial production
variables in arid and semi-arid regions where intensive agriculture is
practiced to meet ever-increasing demand for food and fiber. This is
crucial for the Dez and Moghan command areas where water delivery
problems and adverse environmental issues are widespread. This
paper aims to identify major problems areas using on-farm surveys of
200 farmers, agricultural extensionists and water suppliers which was
complemented by secondary data and field observations during 2010-
2011 cultivating season. The SPSS package was used to analyze and
synthesis data. Results indicated inappropriate canal operations in
both schemes, though there was no unanimity about the underlying
causes. Inequitable and inflexible distribution was found to be rooted
in deficient hydraulic structures particularly in the main and
secondary canals. The inadequacy and inflexibility of water
scheduling regime was the underlying causes of recurring pest and
disease spread which often led to the decline of crop yield and
quality, although these were not disputed, the water suppliers were
not prepared to link with the deficiencies in the operation of the main
and secondary canals. They rather attributed these to the prevailing
salinity; alkalinity, water table fluctuations and leaching of the
valuable agro-chemical inputs from the plants- route zone with farreaching
consequences. Examples of these include the pollution of
ground and surface resources due to over-irrigation at the farm level
which falls under the growers- own responsibility. Poor irrigation
efficiency and adverse environmental problems were attributed to
deficient and outdated farming practices that were in turn rooted in
poor extension programs and irrational water charges.
Abstract: A CFD study on heat flux reduction in hypersonic flow with opposing jet has been conducted. Flowfield parameters, reattachment point position, surface pressure distributions and heat flux distributions are obtained and validated with experiments. The physical mechanism of heat reduction has been analyzed. When the opposing jet blows, the freestream is blocked off, flows to the edges and not interacts with the surface to form aerodynamic heating. At the same time, the jet flows back to form cool recirculation region, which reduces the difference in temperature between the surface and the nearby gas, and then reduces the heat flux. As the pressure ratio increases, the interface between jet and freestream is gradually pushed away from the surface. Larger the total pressure ratio is, lower the heat flux is. To study the effect of the intensity of opposing jet more reasonably, a new parameter RPA has been introduced by combining the flux and the total pressure ratio. The study shows that the same shock wave position and total heat load can be obtained with the same RPA with different fluxes and the total pressures, which means the new parameter could stand for the intensity of opposing jet and could be used to analyze the influence of opposing jet on flow field and aerodynamic heating.
Abstract: In the analysis of structures, the nonlinear effects due to large displacement, large rotation and materially-nonlinear are very important and must be considered for the reliable analysis. The non-linear fmite element analysis has potential as usable and reliable means for analyzing of civil structures with the availability of computer technology. In this research the large displacements and materially nonlinear behavior of shear wall is presented with developing of fmite element code using the standard Galerkin weighted residual formulation. Two-dimensional plane stress model was carried out to present the shear wall response. Total Lagangian formulation, which is computationally more effective, is used in the formulation of stiffness matrices and the Newton-Raphson method is applied for the solution of nonlinear transient equations. The details of the program formulation are highlighted and the results of the analyses are presented, along with a comparison of the response of the structure with Ansys software results. The presented model in this paper can be developed for nonlinear analysis of civil engineering structures with different material behavior and complicated geometry.
Abstract: this article conducts a research about the relationship between cash dividend policy and enterprise value based on the data coming from the A-share listed companies over period 2005-2009. In conclusion, the enterprise value has a negative correlation with the incremental and the degressive cash dividend per share, and has a positive correlation with the stable cash dividend per share.
Abstract: In the paper we presented the possibility of application
collagen gels with active principle-s from marine algae extract and chlorhexidine salt in dental medicine. The hydro-alcoholic extracts
from marine algae have been used as they have been obtained. The extracts from marine algae and chlorhexidine salt (digluconate) are
incorporated in type I non-denatured fibrillar collagen matrixes. In order to obtain therapeutic effects at nanostructure level, it is important to know the rheological characteristics of the relevant mixtures of collagen gels and extracts from marine algae selected for use. In this survey we have studied mixtures made of non-denatured
fibrillar collagen hydro-gels where different concentrations of marine
algae have been incorporated. Based on the data obtained for the
shearing tensions, we have traced the rheograms – the diagrams for shearing tensions depending on the shearing speed values – from
which we have calculated the apparent viscosities as ratios between shearing tension and speed values, which have been figured in
relation to the shearing speed values, with a view to levelling
dependency.
Abstract: This work presents a new algorithm based on a combination of fuzzy (FUZ), Dynamic Programming (DP), and Genetic Algorithm (GA) approach for capacitor allocation in distribution feeders. The problem formulation considers two distinct objectives related to total cost of power loss and total cost of capacitors including the purchase and installation costs. The novel formulation is a multi-objective and non-differentiable optimization problem. The proposed method of this article uses fuzzy reasoning for sitting of capacitors in radial distribution feeders, DP for sizing and finally GA for finding the optimum shape of membership functions which are used in fuzzy reasoning stage. The proposed method has been implemented in a software package and its effectiveness has been verified through a 9-bus radial distribution feeder for the sake of conclusions supports. A comparison has been done among the proposed method of this paper and similar methods in other research works that shows the effectiveness of the proposed method of this paper for solving optimum capacitor planning problem.
Abstract: In this study, the possibility of using potato as a
substrate for glutamic acid production by Brevibacterium linens
was investigated. For preparation of fermentation medium, potato
was hydrolyzed by hydrochloridric acid. The medium contained
potato hydrolysate, tween 80, mineral solution, glucose, and
potassium hydrogen phosphate. The initial pH of the medium was
adjusted to 7-7.5. For achieving the optimum time with maximum
yield, the beakers containing the medium and the inoculums were
incubated in a rotary water bath flask shaker for one to five days.
Thin layer choromatography was used for quantitative and
qualitative assay of the glutamic acid produced. The results
revealed that as fermentation time increased, pH of the
fermentation medium significantly decreased (P
Abstract: The burst noise is a kind of noises that are destructive
and frequently found in semiconductor devices and ICs, yet detecting
and removing the noise has proved challenging for IC designers or users. According to the properties of burst noise, a methodological
approach is presented (proposed) in the paper, by which the burst noise
can be analysed and detected in time domain. In this paper, principles
and properties of burst noise are expounded first, Afterwards,
feasibility (viable) of burst noise detection by means of wavelet
transform in the time domain is corroborated in the paper, and the multi-resolution characters of Gaussian noise, burst noise and blurred
burst noise are discussed in details by computer emulation. Furthermore, the practical method to decide parameters of wavelet
transform is acquired through a great deal of experiment and data statistics. The methodology may yield an expectation in a wide variety of applications.
Abstract: The purpose of this paper is to develop a typology
based on market orientation (MO) and innovation orientation (IO),
and to illustrate to what extent housing companies in Sweden fit
within this framework. A qualitative study on 11 public housing
companies in the central part of Sweden has been conducted by the
help of open and semi-structured questions for data collection. Four
public housing company types- i.e. reactive prospector, proactive
prospector, reactive defender and proactive defender have been
identified by the combination of MO-IO dimensions. Future research
can include other dimensions like entrepreneurship and network to
observe how it particularly affects MO. An empirical study can
compare public and private housing companies on the basis of MO
and IO dimensions. One major contribution of the paper is the
proposition of typology which can be used to describe public housing
companies and deciding their future course of actions.
Abstract: Knowledge of factors, which influence stress and its
distribution, is of key importance to the successful production of
durable restorations. One of this is the marginal geometry. The
objective of this study was to evaluate, by finite element analysis
(FEA), the influence of different marginal designs on the stress
distribution in teeth prepared for cast metal crowns. Five margin
designs were taken into consideration: shoulderless, chamfer,
shoulder, sloped shoulder and shoulder with bevel. For each kind of
preparation three dimensional finite element analyses were initiated.
Maximal equivalent stresses were calculated and stress patterns were
represented in order to compare the marginal designs. Within the
limitation of this study, the shoulder and beveled shoulder margin
preparations of the teeth are preferred for cast metal crowns from
biomechanical point of view.
Abstract: Several different cements have been tested to evaluate
their potential to leach calcium, chromium and aluminum ions in soft
water environment. The research allows comparing some different
cements in order to the potential risk of water contamination. This
can be done only in the same environment. To reach the results in
reasonable short time intervals and to make heavy metals
measurements with high accuracy, demineralized water was used. In
this case the conditions of experiments are far away from the water
supply practice, but short time experiments and measurably high
concentrations of elements in the water solution are an important
advantage. Moreover leaching mechanisms can be recognized, our
experiments reported here refer to this kind of cements evaluation.
Abstract: In spite of the advent of new materials, clay bricks
remain, arguably, the most popular construction materials today.
Nevertheless the low cost and versatility of clay bricks cannot always
be associated with high environmental and sustainable values,
especially in terms of raw material sources and manufacturing
processes. At the same time, the worldwide agricultural footprint is
fast growing, with vast agricultural land cultivation and active
expansion of the agro-based industry. The resulting large quantities of
agricultural wastes, unfortunately, are not always well managed or
utilised. These wastes can be recycled, such as by retrieving fibres
from disposed leaves and fruit bunches, and then incorporated in
brick-making. This way the clay bricks are made a 'greener' building
material and the discarded natural wastes can be reutilised, avoiding
otherwise wasteful landfill and harmful open incineration. This study
examined the physical and mechanical properties of clay bricks made
by adding two natural fibres to a clay-water mixture, with baked and
non-baked conditions. The fibres were sourced from pineapple leaves
(PF) and oil palm fruit bunch (OF), and added within the range of
0.25-0.75 %. Cement was added as a binder to the mixture at 5-15 %.
Although the two fibres had different effects on the bricks produced,
cement appeared to dominate the compressive strength. The
non-baked bricks disintegrated when submerged in water, while the
baked ones displayed cement-dependent characteristics in
water-absorption and density changes. Interestingly, further increase
in fibre content did not cause significant density decrease in both the
baked and non-baked bricks.
Abstract: Design should be viewed concurrently by three ways
as transformation, flow and value generation. An innovative approach
to solve design – related problems is described as the integrated
product - process design. As a foundation for a formal framework
consisting of organizing principles and techniques, Work Structuring
has been developed to guide efforts in the integration that enhances
the development of operation and process design in alignment with
product design.
Vietnam construction projects are facing many delays, and cost
overruns caused mostly by design related problems. A better design
management that integrates product and process design could resolve
these problems. A questionnaire survey and in – depth interviews
were used to investigate the feasibility of applying Work Structuring
to construction projects in Vietnam.
The purpose of this paper is to present the research results and to
illustrate the possible problems and potential solutions when Work
Structuring is implemented to construction projects in Vietnam.
Abstract: We are concerned with a class of quadratic matrix
equations arising from the overdamped mass-spring system. By
exploring the structure of coefficient matrices, we propose a fast
cyclic reduction algorithm to calculate the extreme solutions of the
equation. Numerical experiments show that the proposed algorithm
outperforms the original cyclic reduction and the structure-preserving
doubling algorithm.
Abstract: A universal current-mode biquad is described which
represents an economical variant of well-known KHN (Kerwin,
Huelsman, Newcomb) voltage-mode filter. The circuit consists of
two multiple-output OTAs and of two grounded capacitors. Utilizing
simple splitter of the input current and a pair of jumpers, all the basic
2nd-order transfer functions can be implemented. The principle is
verified by Spice simulation on the level of a CMOS structure of
OTAs.
Abstract: With the increasing number of on-chip components and the critical requirement for processing power, Chip Multiprocessor (CMP) has gained wide acceptance in both academia and industry during the last decade. However, the conventional bus-based onchip communication schemes suffer from very high communication delay and low scalability in large scale systems. Network-on-Chip (NoC) has been proposed to solve the bottleneck of parallel onchip communications by applying different network topologies which separate the communication phase from the computation phase. Observing that the memory bandwidth of the communication between on-chip components and off-chip memory has become a critical problem even in NoC based systems, in this paper, we propose a novel 3D NoC with on-chip Dynamic Random Access Memory (DRAM) in which different layers are dedicated to different functionalities such as processors, cache or memory. Results show that, by using our proposed architecture, average link utilization has reduced by 10.25% for SPLASH-2 workloads. Our proposed design costs 1.12% less execution cycles than the traditional design on average.
Abstract: The system is made with main distributed components:
First Level: Industrial Computers placed in Control Room (monitors thermal and electrical processes based on the data provided by the second level); Second Level: PLCs which collects data from process and transmits information on the first level; also takes commands from this level which are further, passed to execution elements from third
level; Third Level: field elements consisting in 3 categories: data collecting elements; data transfer elements from the third level to the second; execution elements which take commands from the second
level PLCs and executes them after which transmits the confirmation of execution to them. The purpose of the automatic functioning is the optimization of the co-generative electrical energy commissioning in the national
energy system and the commissioning of thermal energy to the consumers.
The integrated system treats the functioning of all the equipments and devices as a whole: Gas Turbine Units (GTU); MT 20kV Medium Voltage Station (MVS); 0,4 kV Low Voltage Station (LVS); Main Hot Water Boilers (MHW); Auxiliary Hot Water Boilers (AHW); Gas Compressor Unit (GCU); Thermal Agent Circulation
Pumping Unit (TPU); Water Treating Station (WTS).