Abstract: Homogeneous Charge Compression (HCCI) Ignition technology has been around for a long time, but has recently received renewed attention and enthusiasm. This paper deals with experimental investigations of HCCI engine using hydrous methanol as a primary fuel and Dimethyl Ether (DME) as an ignition improver. A regular diesel engine has been modified to work as HCCI engine for this investigation. The hydrous methanol is inducted and DME is injected into a single cylinder engine. Hence, hydrous methanol is used with 15% water content in HCCI engine and its performance and emission behavior is documented. The auto-ignition of Methanol is enabled by DME. The quantity of DME varies with respect to the load. In this study, the experiments are conducted independently and the effect of the hydrous methanol on the engine operating limit, heat release rate and exhaust emissions at different load conditions are investigated. The investigation also proves that the Hydrous Methanol with DME operation reduces the oxides of Nitrogen and smoke to an extreme low level which is not possible by the direct injection CI engine. Therefore, it is beneficial to use hydrous methanol-DME HCCI mode while using hydrous methanol in internal Combustion Engines.
Abstract: Bandwidth allocation in wired network is less complex
and to allocate bandwidth in wireless networks is complex and
challenging, due to the mobility of source end system.This paper
proposes a new approach to bandwidth allocation to higher and lower
priority mobile nodes.In our proposal bandwidth allocation to new
mobile node is based on bandwidth utilization of existing mobile
nodes.The first section of the paper focuses on introduction to
bandwidth allocation in wireless networks and presents the existing
solutions available for allocation of bandwidth. The second section
proposes the new solution for the bandwidth allocation to higher and
lower priority nodes. Finally this paper ends with the analytical
evaluation of the proposed solution.
Abstract: In conventional reliability assessment, the reliability data of system components are treated as crisp values. The collected data have some uncertainties due to errors by human beings/machines or any other sources. These uncertainty factors will limit the understanding of system component failure due to the reason of incomplete data. In these situations, we need to generalize classical methods to fuzzy environment for studying and analyzing the systems of interest. Fuzzy set theory has been proposed to handle such vagueness by generalizing the notion of membership in a set. Essentially, in a Fuzzy Set (FS) each element is associated with a point-value selected from the unit interval [0, 1], which is termed as the grade of membership in the set. A Vague Set (VS), as well as an Intuitionistic Fuzzy Set (IFS), is a further generalization of an FS. Instead of using point-based membership as in FS, interval-based membership is used in VS. The interval-based membership in VS is more expressive in capturing vagueness of data. In the present paper, vague set theory coupled with conventional Lambda-Tau method is presented for reliability analysis of repairable systems. The methodology uses Petri nets (PN) to model the system instead of fault tree because it allows efficient simultaneous generation of minimal cuts and path sets. The presented method is illustrated with the press unit of the paper mill.
Abstract: This study developed a high efficient and combined
biological and chemical filter treatment process. This process used
PAC (Powder Activated Carbon), Alum and attached growth
treatment process. The system removals of total nitrogen and total
phosphorus ratio of two were as high as 70% and 73%, moreover, the
effluent water was suitable to urban and agricultural water. Also the
advantages of this process are not only occupies small place but is
simple, economic and easy operating. Besides, our developed process
can keep stable process efficiency even in relative low load level.
Therefore, this study judges that use of the high efficient and
combined biological and chemical filter treatment process, it is
expected that the effluent water in this system can be reused as urban
and agricultural water.
Abstract: The purpose of this research is to compare the original
intra-oral digital dental radiograph images with images that are
enhanced using a combination of image processing algorithms. Intraoral
digital dental radiograph images are often noisy, blur edges and
low in contrast. A combination of sharpening and enhancement
method are used to overcome these problems. Three types of
proposed compound algorithms used are Sharp Adaptive Histogram
Equalization (SAHE), Sharp Median Adaptive Histogram
Equalization (SMAHE) and Sharp Contrast adaptive histogram
equalization (SCLAHE). This paper presents an initial study of the
perception of six dentists on the details of abnormal pathologies and
improvement of image quality in ten intra-oral radiographs. The
research focus on the detection of only three types of pathology
which is periapical radiolucency, widen periodontal ligament space
and loss of lamina dura. The overall result shows that SCLAHE-s
slightly improve the appearance of dental abnormalities- over the
original image and also outperform the other two proposed
compound algorithms.
Abstract: The aim of this paper is to develop a new two dimensional time accurate Euler solver for shock tube applications. The solver was developed to study the performance of a newly built short-duration hypersonic test facility at Universiti Tenaga Nasional “UNITEN" in Malaysia. The facility has been designed, built, and commissioned for different values of diaphragm pressure ratios in order to get wide range of Mach number. The developed solver uses second order accurate cell-vertex finite volume spatial discretization and forth order accurate Runge-Kutta temporal integration and it is designed to simulate the flow process for similar driver/driven gases (e.g. air-air as working fluids). The solver is validated against analytical solution and experimental measurements in the high speed flow test facility. Further investigations were made on the flow process inside the shock tube by using the solver. The shock wave motion, reflection and interaction were investigated and their influence on the performance of the shock tube was determined. The results provide very good estimates for both shock speed and shock pressure obtained after diaphragm rupture. Also detailed information on the gasdynamic processes over the full length of the facility is available. The agreements obtained have been reasonable.
Abstract: This paper presents the experimental results on effect of applied voltage stress frequency to the occurrence of electrical treeing in 22 kV cross linked polyethylene (XLPE) insulated cable.Hallow disk of XLPE insulating material with thickness 5 mm taken from unused high voltage cable was used as the specimen in this study. Stainless steel needle was inserted gradually into the specimen to give a tip to earth plane electrode separation of 2.50.2 mm at elevated temperature 105-110°C. The specimen was then annealed for 5 minute to minimize any mechanical stress build up around the needle-plane region before it was cooled down to room temperature. Each specimen were subjected to the same applied voltage stress level at 8 kV AC rms, with various frequency, 50, 100, 500, 1000 and 2000 Hz. Initiation time, propagation speed and pattern of electrical treeing were examined in order to study the effect of applied voltage stress frequency. By the experimental results, initial time of visible treeing decreases with increasing in applied voltage frequency. Also, obviously, propagation speed of electrical treeing increases with increasing in applied voltage frequency.Furthermore, two types of electrical treeing, bush-like and branch-like treeing were observed.The experimental results confirmed the effect of voltage stress frequency as well.
Abstract: In this paper, one-dimensional analysis of flow in a
single-stage gas gun is conducted. The compressible inviscid flow
equations are numerically solved by the second-order Roe TVD
method, by using moving boundaries. For investigation of real gas
effect the Noble-Able equation is applied. The numerical results are
compared with the experimental data to validate the numerical
scheme. The results show that with using the Noble-Able equation,
the muzzle velocity decreases.
Abstract: Zeolite A and MCM-41 have extensive applications in basic science, petrochemical science, energy conservation/storage, medicine, chemical sensor, air purification, environmentally benign composite structure and waste remediation. However, the use of zeolite A and MCM-41 in these areas, especially environmental remediation, are restricted due to prohibitive production cost. Efficient recycling of and resource recovery from coal fly ash has been a major topic of current international research interest, aimed at achieving sustainable development of human society from the viewpoints of energy, economy, and environmental strategy. This project reported an original, novel, green and fast methods to produce nano-porous zeolite A and MCM-41 materials from coal fly ash. For zeolite A, this novel production method allows a reduction by half of the total production time while maintaining a high degree of crystallinity of zeolite A which exists in a narrower particle size distribution. For MCM-41, this remarkably green approach, being an environmentally friendly process and reducing generation of toxic waste, can produce pure and long-range ordered MCM-41 materials from coal fly ash. This approach took 24 h at 25 oC to produce 9 g of MCM-41 materials from 30 g of the coal fly ash, which is the shortest time and lowest reaction temperature required to produce pure and ordered MCM-41 materials (having the largest internal surface area) compared to the values reported in the literature. Performance evaluation of the produced zeolite A and MCM-41 materials in wastewater treatment and air pollution control were reported. The residual fly ash was also converted to zeolite Na-P1 which showed good performance in removal of multi-metal ions in wastewater. In wastewater treatment, compared to commercial-grade zeolite A, adsorbents produced from coal fly ash were effective in removing multi heavy metal ions in water and could be an alternative material for treatment of wastewater. In methane emission abatement, the zeolite A (produced from coal fly ash) achieved similar methane removal efficiency compared to the zeolite A prepared from pure chemicals. This report provides the guidance for production of zeolite A and MCM-41 from coal fly ash by a cost-effective approach which opens potential applications of these materials in environmental industry. Finally, environmental and economic aspects of production of zeolite A and MCM-41 from coal fly ash were discussed.
Abstract: This article presents the boundary conditions for the problem of turbulent supersonic gas flow in a plane channel with a perpendicular injection jets. The non-reflection boundary conditions for direct modeling of compressible viscous gases are studied. A formulation using the NSCBC (Navier- Stocks characteristic boundary conditions) through boundaries is derived for the subsonic inflow and subsonic non-reflection outflow situations. Verification of the constructed algorithm of boundary conditions is carried out by solving a test problem of perpendicular sound of jets injection into a supersonic gas flow in a plane channel.
Abstract: We consider a two-way relay network where two sources exchange information. A relay helps the two sources exchange information using the decode-and-XOR-forward protocol. We investigate the power minimization problem with minimum rate constraints. The system needs two time slots and in each time slot the required rate pair should be achievable. The power consumption is minimized in each time slot and we obtained the closed form solution. The simulation results confirm that the proposed power allocation scheme consumes lower total power than the conventional schemes.
Abstract: A systematic way to derive the conserved quantities for the axisymmetric liquid jet, free jet and wall jet using conservation laws is presented. The flow in axisymmetric jets is governed by Prandtl-s momentum boundary layer equation and the continuity equation. The multiplier approach is used to construct a basis of conserved vectors for the system of two partial differential equations for the two velocity components. The basis consists of two conserved vectors. By integrating the corresponding conservation laws across the jet and imposing the boundary conditions, conserved quantities are derived for the axisymmetric liquid and free jet. The multiplier approach applied to the third-order partial differential equation for the stream function yields two local conserved vectors one of which is a non-local conserved vector for the system. One of the conserved vectors gives the conserved quantity for the axisymmetric free jet but the conserved quantity for the wall jet is not obtained from the second conserved vector. The conserved quantity for the axisymmetric wall jet is derived from a non-local conserved vector of the third-order partial differential equation for the stream function. This non-local conserved vector for the third-order partial differential equation for the stream function is obtained by using the stream function as multiplier.
Abstract: In this paper motion analysis on a winding
stair-climbing is investigated using our proposed rotational arm type
of robotic wheelchair. For now, the robotic wheelchair is operated in
an open mode to climb winding stairs by a dynamic turning, therefore,
the dynamics model is required to ensure a passenger-s safety.
Equations of motion based on the skid-steering analysis are developed
for the trajectory planning and motion analysis on climbing winding
stairs. Since the robotic wheelchair must climb a winding staircase
stably, the winding trajectory becomes a constraint equation to be
followed, and the Baumgarte-s method is used to solve for the
constrained dynamics equations. Experimental results validate the
behavior of the prototype as it climbs a winding stair.
Abstract: This paper presented a MATLAB-based system named Smart Access Network Testing, Analyzing and Database (SANTAD), purposely for in-service transmission surveillance and self restoration against fiber fault in fiber-to-the-home (FTTH) access network. The developed program will be installed with optical line terminal (OLT) at central office (CO) to monitor the status and detect any fiber fault that occurs in FTTH downwardly from CO towards residential customer locations. SANTAD is interfaced with optical time domain reflectometer (OTDR) to accumulate every network testing result to be displayed on a single computer screen for further analysis. This program will identify and present the parameters of each optical fiber line such as the line's status either in working or nonworking condition, magnitude of decreasing at each point, failure location, and other details as shown in the OTDR's screen. The failure status will be delivered to field engineers for promptly actions, meanwhile the failure line will be diverted to protection line to ensure the traffic flow continuously. This approach has a bright prospect to improve the survivability and reliability as well as increase the efficiency and monitoring capabilities in FTTH.
Abstract: In this paper, removal of chromium(VI) from aqueous
solution has been researched using reverse osmosis. The influence of
transmembrane pressure and feed concentration on permeate flux,
water recovery, permeate concentration, and salt rejection was
studied. The results showed that according to the variation of
transmembrane pressure and feed concentration, the permeate flux
and salt rejection were in the range 19.17 to 58.75 l/m2.min and
99.51 to 99.8 %, respectively. The highest permeate flux, 58.75
l/m2.min, and water recovery, 42.47 %, were obtained in the highest
pressure and the lowest feed concentration. On the other hand, the
lowest permeate concentration, 0.01 mg/l, and the highest salt
rejection, 99.8 %, were obtained in the highest pressure and the
lowest feed concentration.
Abstract: The gamma radiation in samples of a variety of
natural tiling rocks (granites) produced and imported in Iran use in
the building industry was measured, employing high-resolution
Gamma-ray spectroscopy. The rock samples were pulverized, sealed
in 0.5 liter plastic Marinelli beakers, and measured in the laboratory
with an accumulating time between 50000 and 80000 second each.
From the measured Gamma-ray spectra, activity concentrations were
determined for 232Th (range from 6.5 to 172.2 Bq kg-1), 238U (from
7.5 to 178.1 Bq kg-1 ),226Ra( from 3.8 to 94.2 Bq kg-1 ) 40K (from
556.9 to 1539.2 Bq kg-1). From the 29 samples measured in this
study, “Nehbndan ( Berjand )" appears to present the highest
concentrations for 232Th,“Big Red Flower (China) "for 238U , “
Khoram dareh" for 226 Ra and “ Peranshahr" for 40K , respectively.
Abstract: This paper discusses the use of explorative data
mining tools that allow the educator to explore new relationships
between reported learning experiences and actual activities,
even if there are multiple dimensions with a large number
of measured items. The underlying technology is based on
the so-called Compendium Platform for Reproducible Computing
(http://www.freestatistics.org) which was built on top the computational
R Framework (http://www.wessa.net).
Abstract: This paper is the tomographic images reconstruction
simulation for defects detection in specimen. The specimen is the
thin cylindrical steel contained with low density materials. The
defects in material are simulated in three shapes.The specimen image
function will be transformed to projection data. Radon transform and
its inverse provide the mathematical for reconstructing tomographic
images from projection data. The result of the simulation show that
the reconstruction images is complete for defect detection.
Abstract: Lutein is a dietary oxycarotenoid which is found
to reduce the risks of Age-related Macular Degeneration
(AMD). Supercritical fluid extraction of lutein esters from
marigold petals was carried out and was found to be much
effective than conventional solvent extraction. The
saponification of pre-concentrated lutein esters to produce free
lutein was studied which showed a composition of about 88%
total carotenoids (UV-VIS spectrophotometry) and 90.7%
lutein (HPLC). The lipase catalyzed hydrolysis of lutein esters
in conventional medium was investigated. The optimal
temperature, pH, enzyme concentration and water activity
were found to be 50°C, 7, 15% and 0.33 respectively and the
activity loss of lipase was about 25% after 8 times re-use in at
50°C for 12 days. However, the lipase catalyzed hydrolysis of
lutein esters in conventional media resulted in poor
conversions (16.4%).
Abstract: Model Predictive Control (MPC) is an established control
technique in a wide range of process industries. The reason for
this success is its ability to handle multivariable systems and systems
having input, output or state constraints. Neverthless comparing to
PID controller, the implementation of the MPC in miniaturized
devices like Field Programmable Gate Arrays (FPGA) and microcontrollers
has historically been very small scale due to its complexity in
implementation and its computation time requirement. At the same
time, such embedded technologies have become an enabler for future
manufacturing enterprisers as well as a transformer of organizations
and markets. In this work, we take advantage of these recent advances
in this area in the deployment of one of the most studied and applied
control technique in the industrial engineering. In this paper, we
propose an efficient firmware for the implementation of constrained
MPC in the performed STM32 microcontroller using interior point
method. Indeed, performances study shows good execution speed
and low computational burden. These results encourage to develop
predictive control algorithms to be programmed in industrial standard
processes. The PID anti windup controller was also implemented in
the STM32 in order to make a performance comparison with the
MPC. The main features of the proposed constrained MPC framework
are illustrated through two examples.