Abstract: Computer based geostatistical methods can offer effective data analysis possibilities for agricultural areas by using
vectorial data and their objective informations. These methods will help to detect the spatial changes on different locations of the large
agricultural lands, which will lead to effective fertilization for optimal yield with reduced environmental pollution. In this study, topsoil (0-20 cm) and subsoil (20-40 cm) samples were taken from a
sugar beet field by 20 x 20 m grids. Plant samples were also collected
from the same plots. Some physical and chemical analyses for these
samples were made by routine methods. According to derived variation coefficients, topsoil organic matter (OM) distribution was more than subsoil OM distribution. The highest C.V. value of
17.79% was found for topsoil OM. The data were analyzed
comparatively according to kriging methods which are also used
widely in geostatistic. Several interpolation methods (Ordinary,Simple and Universal) and semivariogram models (Spherical,
Exponential and Gaussian) were tested in order to choose the suitable
methods. Average standard deviations of values estimated by simple
kriging interpolation method were less than average standard
deviations (topsoil OM ± 0.48, N ± 0.37, subsoil OM ± 0.18) of measured values. The most suitable interpolation method was simple
kriging method and exponantial semivariogram model for topsoil,
whereas the best optimal interpolation method was simple kriging
method and spherical semivariogram model for subsoil. The results
also showed that these computer based geostatistical methods should
be tested and calibrated for different experimental conditions and semivariogram models.
Abstract: The stability characteristics of water lubricated journal bearings having three axial grooves are obtained theoretically. In this lubricant (water) is fed under pressure from one end of the bearing, through the 3-axial grooves (groove angles may vary). These bearings can use the process fluid as the lubricant, as in the case of feed water pumps. The Reynolds equation is solved numerically by the finite difference method satisfying the boundary conditions. The stiffness and damping coefficient for various bearing number and eccentricity ratios, assuming linear pressure drop along the groove, shows that smaller groove angles better results.
Abstract: Addis Ababa is a seat of African Union (AU), United
Nations Economic Commission for Africa (UN-ECA) and hundreds of
embassies and consular representatives. Addis Ababa is one of the
highest capitals in the world with an average 2400 meters above sea
level. It is dichotomous city with a blend of modern high-rise and
deteriorating slum quarters. Water supply and sanitation, waste
management and housing are continuing to be serious problems.
Forest wood based domestic energy use as well as uncontrolled
emissions from mobile and fixed sources has endangered the state of
the urban environment. Analysis based on satellite imagery has
revealed the deteriorating urban environment within the last three
decades. The recently restructured city administration has brought
improvements in the condition of the urban environment. However,
the overwhelming size of the challenges faced by the city dwarfed
their fairly good results.
Abstract: Low-carbon economy means the energy conservation and emission reduction. How to measure and evaluate the regional low-carbon economy is an important problem which should be solved immediately. This paper proposed the eco-efficiency ratio based on the ecological efficiency to evaluate the current situation of the low-carbon economy in Jiangsu province and to analyze the efficiency of the low-carbon economy in Jiangsu and other provinces, compared both advantages and disadvantages. And then this paper put forward some advices for the government to formulate the correct development policy of low-carbon economy, to improve the technology innovation capacity and the efficiency of resource allocation.
Abstract: The prediction of transmembrane helical segments
(TMHs) in membrane proteins is an important field in the
bioinformatics research. In this paper, a method based on discrete
wavelet transform (DWT) has been developed to predict the number
and location of TMHs in membrane proteins. PDB coded as 1F88 was
chosen as an example to describe the prediction of the number and
location of TMHs in membrane proteins by using this method. One
group of test data sets that contain total 19 protein sequences was
utilized to access the effect of this method. Compared with the
prediction results of DAS, PRED-TMR2, SOSUI, HMMTOP2.0 and
TMHMM2.0, the obtained results indicate that the presented method
has higher prediction accuracy.
Abstract: Along with increasing development of generation of supersonic planes especially fighters and request for increasing the performance and maneuverability scientists and engineers suggested the delta and double delta wing design. One of the areas which was necessary to be researched, was the Aerodynamic review of this type of wings in high angles of attack at low speeds that was very important in landing and takeoff the planes and maneuvers. Leading Edges of the wings,cause the separation flow from wing surface and then formation of powerful vortex with high rotational speed which studing the mechanism and location of formation and also the position of the vortex breakdown in high angles of attack is very important. In this research, a double delta wing with 76o/45o sweep angles at high angle of attack in steady state and incompressible flow were numerically analyzed with Fluent software. With analaysis of the numerical results, we arrived the most important characteristic of the double delta wings which is keeping of lift at high angles of attacks.
Abstract: After the terrorist attack on September 11, 2001 in
U.S., the container security issue got high attention, especially by U.S.
government, which deployed a lot of measures to promote or improve
security systems. U.S. government not only enhances its national
security system, but allies with other countries against the potential
terrorist attacks in the future. For example CSI (Container Security
Initiative), it encourages foreign ports outside U.S. to become CSI
ports as a part of U.S. anti-terrorism network. Although promotion of
the security could partly reach the goal of anti-terrorism, that will
influence the efficiency of container supply chain, which is the main
concern when implementing the inspection measurements. This paper
proposes a quick estimation methodology for an inspection service
rate by a berth allocation heuristic such that the inspection activities
will not affect the original container supply chain. Theoretical and
simulation results show this approach is effective.
Abstract: This paper presents an online method that learns the
corresponding points of an object from un-annotated grayscale images
containing instances of the object. In the first image being
processed, an ensemble of node points is automatically selected
which is matched in the subsequent images. A Bayesian posterior
distribution for the locations of the nodes in the images is formed.
The likelihood is formed from Gabor responses and the prior assumes
the mean shape of the node ensemble to be similar in a translation
and scale free space. An association model is applied for separating
the object nodes and background nodes. The posterior distribution is
sampled with Sequential Monte Carlo method. The matched object
nodes are inferred to be the corresponding points of the object
instances. The results show that our system matches the object nodes
as accurately as other methods that train the model with annotated
training images.
Abstract: This paper presents a computational study of the separated flow in a planer asymmetric diffuser. The steady RANS equations for turbulent incompressible fluid flow and six turbulence closures are used in the present study. The commercial software code, FLUENT 6.3.26, was used for solving the set of governing equations using various turbulence models. Five of the used turbulence models are available directly in the code while the v2-f turbulence model was implemented via User Defined Scalars (UDS) and User Defined Functions (UDF). A series of computational analysis is performed to assess the performance of turbulence models at different grid density. The results show that the standard k-ω, SST k-ω and v2-f models clearly performed better than other models when an adverse pressure gradient was present. The RSM model shows an acceptable agreement with the velocity and turbulent kinetic energy profiles but it failed to predict the location of separation and attachment points. The standard k-ε and the low-Re k- ε delivered very poor results.
Abstract: Ti-6Al-4V alloy has demonstrated a high strength to
weight ratio as well as good properties at high temperature. The
successful application of the alloy in some important areas depends
on suitable joining techniques. Friction welding has many
advantageous features to be chosen for joining Titanium alloys. The
present work investigates the feasibility of producing similar metal
joints of this Titanium alloy by rotary friction welding method. The
joints are produced at three different speeds and the performances of
the welded joints are evaluated by conducting microstructure studies,
Vickers Hardness and tensile tests at the joints. It is found that the
weld joints produced are sound and the ductile fractures in the tensile
weld specimens occur at locations away from the welded joints. It is
also found that a rotational speed of 1500 RPM can produce a very
good weld, with other parameters kept constant.
Abstract: Identifying protein coding regions in DNA sequences is a basic step in the location of genes. Several approaches based on signal processing tools have been applied to solve this problem, trying to achieve more accurate predictions. This paper presents a new predictor that improves the efficacy of three techniques that use the Fourier Transform to predict coding regions, and that could be computed using an algorithm that reduces the computation load. Some ideas about the combination of the predictor with other methods are discussed. ROC curves are used to demonstrate the efficacy of the proposed predictor, based on the computation of 25 DNA sequences from three different organisms.
Abstract: The main aims in this research are to study the solid
waste generation in the Faculty of Engineering and Built
Environment in the UKM and at the same time to determine
composition and some of the waste characteristics likewise: moisture
content, density, pH and C/N ratio. For this purpose multiple
campaigns were conducted to collect the wastes produced in all
hostels, faculties, offices and so on, during 24th of February till 2nd
of March 2009, measure and investigate them with regard to both
physical and chemical characteristics leading to highlight the
necessary management policies. Research locations are Faculty of
Engineering and the Canteen nearby that. From the result gained, the
most suitable solid waste management solution will be proposed to
UKM. The average solid waste generation rate in UKM is 203.38
kg/day. The composition of solid waste generated are glass, plastic,
metal, aluminum, organic and inorganic waste and others waste.
From the laboratory result, the average moisture content, density, pH
and C/N ratio values from the solid waste generated are 49.74%,
165.1 kg/m3, 5.3, and 7:1 respectively. Since, the food waste (organic
waste) were the most dominant component, around 62% from the
total waste generated hence, the most suitable solid waste
management solution is composting.
Abstract: Sinc-collocation scheme is one of the new techniques
used in solving numerical problems involving integral equations. This
method has been shown to be a powerful numerical tool for finding
fast and accurate solutions. So, in this paper, some properties of the
Sinc-collocation method required for our subsequent development
are given and are utilized to reduce integral equation of the first
kind to some algebraic equations. Then convergence with exponential
rate is proved by a theorem to guarantee applicability of numerical
technique. Finally, numerical examples are included to demonstrate
the validity and applicability of the technique.
Abstract: Cosmic showers, from their places of origin in space,
after entering earth generate secondary particles called Extensive Air
Shower (EAS). Detection and analysis of EAS and similar High
Energy Particle Showers involve a plethora of experimental setups
with certain constraints for which soft-computational tools like
Artificial Neural Network (ANN)s can be adopted. The optimality
of ANN classifiers can be enhanced further by the use of Multiple
Classifier System (MCS) and certain data - dimension reduction
techniques. This work describes the performance of certain data
dimension reduction techniques like Principal Component Analysis
(PCA), Independent Component Analysis (ICA) and Self Organizing
Map (SOM) approximators for application with an MCS formed
using Multi Layer Perceptron (MLP), Recurrent Neural Network
(RNN) and Probabilistic Neural Network (PNN). The data inputs are
obtained from an array of detectors placed in a circular arrangement
resembling a practical detector grid which have a higher dimension
and greater correlation among themselves. The PCA, ICA and SOM
blocks reduce the correlation and generate a form suitable for real
time practical applications for prediction of primary energy and
location of EAS from density values captured using detectors in a
circular grid.
Abstract: The fixed partial dentures are mainly used in the frontal
part of the dental arch because of their great esthetics. There are
several factors that are associated with the stress state created in
ceramic restorations, including: thickness of ceramic layers,
mechanical properties of the materials, elastic modulus of the
supporting substrate material, direction, magnitude and frequency of
applied load, size and location of occlusal contact areas, residual
stresses induced by processing or pores, restoration-cement
interfacial defects and environmental defects. The purpose of this
study is to evaluate the capability of Polarization Sensitive Optical
Coherence Tomography (PSOCT) in detection and analysis of
possible material defects in metal-ceramic and integral ceramic fixed
partial dentures. As a conclusion, it is important to have a non
invasive method to investigate fixed partial prostheses before their
insertion in the oral cavity in order to satisfy the high stress
requirements and the esthetic function.
Abstract: Dynamic location referencing method is an important technology to shield map differences. These method references objects of the road network by utilizing condensed selection of its real-world geographic properties stored in a digital map database, which overcomes the defections existing in pre-coded location referencing methods. The high attributes completeness requirements and complicated reference point selection algorithm are the main problems of recent researches. Therefore, a dynamic location referencing algorithm combining intersection points selected at the extremities compulsively and road link points selected according to link partition principle was proposed. An experimental system based on this theory was implemented. The tests using Beijing digital map database showed satisfied results and thus verified the feasibility and practicability of this method.
Abstract: GSM has undoubtedly become the most widespread
cellular technology and has established itself as one of the most
promising technology in wireless communication. The next
generation of mobile telephones had also become more powerful and
innovative in a way that new services related to the user-s location
will arise. Other than the 911 requirements for emergency location
initiated by the Federal Communication Commission (FCC) of the
United States, GSM positioning can be highly integrated in cellular
communication technology for commercial use. However, GSM
positioning is facing many challenges. Issues like accuracy,
availability, reliability and suitable cost render the development and
implementation of GSM positioning a challenging task. In this paper,
we investigate the optimal mobile position tracking means. We
employ an innovative scheme by integrating the Kalman filter in the
localization process especially that it has great tracking
characteristics. When tracking in two dimensions, Kalman filter is
very powerful due to its reliable performance as it supports
estimation of past, present, and future states, even when performing
in unknown environments. We show that enhanced position tracking
results is achieved when implementing the Kalman filter for GSM
tracking.
Abstract: This paper presents a new approach for the protection
of Thyristor-Controlled Series Compensator (TCSC) line using
Support Vector Machine (SVM). One SVM is trained for fault
classification and another for section identification. This method use
three phase current measurement that results in better speed and
accuracy than other SVM based methods which used single phase
current measurement. This makes it suitable for real-time protection.
The method was tested on 10,000 data instances with a very wide
variation in system conditions such as compensation level, source
impedance, location of fault, fault inception angle, load angle at
source bus and fault resistance. The proposed method requires only
local current measurement.
Abstract: In this paper optimal capacitor placement problem has
been formulated in a restructured distribution network. In this
scenario the distribution network operator can consider reactive
energy also as a service that can be sold to transmission system. Thus
search for optimal location, size and number of capacitor banks with
the objective of loss reduction, maximum income from selling
reactive energy to transmission system and return on investment for
capacitors, has been performed. Results is influenced with economic
value of reactive energy, therefore problem has been solved for
various amounts of it. The implemented optimization technique is
genetic algorithm. For any value of reactive power economic value,
when reverse of investment index increase and change from zero or
negative values to positive values, the threshold value of selling
reactive power has been obtained. This increasing price of economic
parameter is reasonable until the network losses is less than loss
before compensation.
Abstract: The charnockitic and associated granitic rocks of Akure area were studied for their field and petrographic relationship's. The outcrops locations were plotted in Surfer 8. The granitic rock exhibits a porphyritic texture and outcrops in the north-eastern side of the study area while the charnockitics outcrop in the central/western part. An essentially dark coloured and fine grained intrusive exhibiting xenoliths and xenocrysts (plagioclase phenocrysts) of the granite outcrops between the granitic and charnockitic rocks. Mineralogically, the central rock combines the content of the other two indicating that it is most likely a product of their hybridization. The charnockitic magma is believed to have intruded and assimilated the granite substantially thereby contaminating itself and consequently emplacing the hybrid. The presented model of emplacement elucidates the hybridization proposal. Conclusively, the charnockitics are believed to be (a) younger than the granite, (b) of Pan-African age and (c) of igneous origin.