Abstract: In this paper a new method is suggested for risk
management by the numerical patterns in data-mining. These patterns
are designed using probability rules in decision trees and are cared to
be valid, novel, useful and understandable. Considering a set of
functions, the system reaches to a good pattern or better objectives.
The patterns are analyzed through the produced matrices and some
results are pointed out. By using the suggested method the direction
of the functionality route in the systems can be controlled and best
planning for special objectives be done.
Abstract: This paper presents an adaptive nonlinear position
controller with velocity constraint, capable of combining the
input-output linearization technique and Lyapunov stability theory.
Based on the Lyapunov stability theory, the adaptation law of the
proposed controller is derived along with the verification of the overall
system-s stability. Computer simulation results demonstrate that the
proposed controller is robust and it can ensure transient stability of
BLDCM, under the occurrence of a large sudden fault.
Abstract: In this paper, a new model order reduction
phenomenon is introduced at the design stage of linear phase digital
IIR filter. The complexity of a system can be reduced by adopting the
model order reduction method in their design. In this paper a mixed
method of model order reduction is proposed for linear IIR filter. The
proposed method employs the advantages of factor division technique
to derive the reduced order denominator polynomial and the reduced
order numerator is obtained based on the resultant denominator
polynomial. The order reduction technique is used to reduce the delay
units at the design stage of IIR filter. The validity of the proposed
method is illustrated with design example in frequency domain and
stability is also examined with help of nyquist plot.
Abstract: As the Internet technology has developed rapidly, the
number of identities (IDs) managed by each individual person has
increased and various ID management technologies have been
developed to assist users. However, most of these technologies are
vulnerable to the existing hacking methods such as phishing attacks
and key-logging. If the administrator-s password is exposed, an
attacker can access the entire contents of the stolen user-s data files in
other devices. To solve these problems, we propose here a new ID
management scheme based on a Single Password Protocol. The paper
presents the details of the new scheme as well as a formal analysis of
the method using BAN Logic.
Abstract: People usually have a telephone voice, which means
they adjust their speech to fit particular situations and to blend in with
other interlocutors. The question is: Do we speak differently to
different people? This possibility has been suggested by social
psychologists within Accommodation Theory [1]. Converging toward
the speech of another person can be regarded as a polite speech
strategy while choosing a language not used by the other interlocutor
can be considered as the clearest example of speech divergence [2].
The present study sets out to investigate such processes in the course
of everyday telephone conversations. Using Joos-s [3] model of
formality in spoken English, the researchers try to explore
convergence to or divergence from the addressee. The results
propound the actuality that lexical choice, and subsequently, patterns
of style vary intriguingly in concordance with the person being
addressed.
Abstract: In rotating machinery one of the critical components
that is prone to premature failure is the rolling bearing.
Consequently, early warning of an imminent bearing failure is much
critical to the safety and reliability of any high speed rotating
machines. This study is concerned with the application of Recurrence
Quantification Analysis (RQA) in fault detection of rolling element
bearings in rotating machinery. Based on the results from this study it
is reported that the RQA variable, percent determinism, is sensitive
to the type of fault investigated and therefore can provide useful
information on bearing damage in rolling element bearings.
Abstract: This work deals with problems of tool axis inclination angles in ball-end milling. Tool axis inclination angle contributes to improvement of functional surface properties (surface integrity - surface roughness, residual stress, micro hardness, etc.), decreasing cutting forces and improving production. By milling with ball-end milling tool, using standard way of cutting, when work piece and cutting tool contain right angle, we have zero cutting speed on edge. At this point cutting tool only pushes material into the work piece. Here we can observe the following undesirable effects - chip contraction, increasing of cutting temperature, increasing vibrations or creation of built-up edge. These effects have negative results – low quality of surface and decreasing of tool life (in the worse case even it is pinching out). These effects can be eliminated with the tilt of cutting tool or tilt of work piece.
Abstract: This paper introduces the effective speckle reduction of
synthetic aperture radar (SAR) images using inner product spaces in
undecimated wavelet domain. There are two major areas in projection
onto span algorithm where improvement can be made. First is the use
of undecimated wavelet transformation instead of discrete wavelet
transformation. And second area is the use of smoothing filter namely
directional smoothing filter which is an additional step. Proposed
method does not need any noise estimation and thresholding
technique. More over proposed method gives good results on both
single polarimetric and fully polarimetric SAR images.
Abstract: Internal combustion engines rejects 30-40% of the
energy supplied by fuel to the environment through exhaust gas. thus, there is a possibility for further significant improvement of efficiency with the utilization of exhaust gas energy and its conversion to mechanical energy or electrical energy. The Thermo-Electric
Generator (TEG) will be located in the exhaust system and will make use of an energy flow between the warmer exhaust gas and the external environment. Predict to th optimum position of temperature
distribution and the performance of TEG through numerical analysis.
The experimental results obtained show that the power output significantly increases with the temperature difference between cold
and hot sides of a thermoelectric generator.
Abstract: The availability of broadband internet and increased
access to computers has been instrumental in the rise of internet
literacy in Malaysia. This development has led to the adoption of
online shopping by many Malaysians. On another note, the
Government has supported the development and production of local
herbal products. This has resulted in an increase in the production and
diversity of products by SMEs. The purpose of this study is to
evaluate the influence of the Malaysian demographic factors and
selected attitudinal characteristics in relation to the online purchasing
of herbal products. In total, 1054 internet users were interviewed
online and Chi-square analysis was used to determine the relationship
between demographic variables and different aspects of online
shopping for herbal products. The overall results show that the
demographic variables such as age, gender, education level, income
and ethnicity were significant when considering the online shopping
antecedents of trust, quality of herbal products, perceived risks and
perceived benefits.
Abstract: This study presents a systematic analysis of wetted region due to cooling of aluminum plate by water spray impingement with respect to different water flow rates, spray nozzle heights, and subcooling. Unlike jet impingement, the wetting is not commenced upon spray impingement and there is a delay in wetness of hot test surface. After initiation, the wetting (black zone) progresses gradually to cover all test plate and provides efficient cooling in nucleate boiling regime. Generally, spray cooling is found function of spray flow rate, spray-to-surface distance and water subcooling. Wetting delay is decreasing by increasing of spray flow rate until spray impact area is not become bigger that test surface. Otherwise, higher spray flow rate is not practically accelerated start of wetting. Very fast wetting due to spray cooling can be obtained by dense spray (high floe rate) discharged from adjacent nozzle to the test surface. Highly subcooling water spray also triggers earlier wetting of hot aluminum plate.
Abstract: This paper addresses the problem of asymptotic tracking
control of a linear parabolic partial differential equation with indomain
point actuation. As the considered model is a non-standard
partial differential equation, we firstly developed a map that allows
transforming this problem into a standard boundary control problem
to which existing infinite-dimensional system control methods can
be applied. Then, a combination of energy multiplier and differential
flatness methods is used to design an asymptotic tracking controller.
This control scheme consists of stabilizing state-feedback derived
from the energy multiplier method and feed-forward control based
on the flatness property of the system. This approach represents
a systematic procedure to design tracking control laws for a class
of partial differential equations with in-domain point actuation. The
applicability and system performance are assessed by simulation
studies.
Abstract: In industrial scale of Gas to Liquid (GTL) process in
Fischer-Tropsch (FT) synthesis, a part of reactor outlet gases such as
CO2 and CH4 as side reaction products, is usually recycled. In this
study, the influence of CO2 and CH4 on the performance and
selectivity of Co-Ru/Al2O3 catalyst is investigated by injection of
these gases (0-20 vol. % of feed) to the feed stream. The effect of
temperature and feed flow rate, are also inspected. The results show
that low amounts of CO2 in the feed stream, doesn`t change the
catalyst activity significantly but increasing the amount of CO2 (more
than 10 vol. %) cause the CO conversion to decrease and the
selectivity of heavy components to increase. Methane acts as an inert
gas and doesn`t affect the catalyst performance. Increasing feed flow
rate has negative effect on both CO conversion and heavy component
selectivity. By raising the temperature, CO conversion will increase
but there are more volatile components in the product. The effect of
CO2 on the catalyst deactivation is also investigated carefully and a
mechanism is suggested to explain the negative influence of CO2 on
catalyst deactivation.
Abstract: Nowadays, consumption of whole flours and flours
with high extraction rate is recommended, because of their high
amount of fibers, vitamins and minerals. Despite nutritional benefits
of whole flour, concentration of some undesirable components such
as phytic acid is higher than white flour. In this study, effect of
several lactic acid bacteria sourdough on Toast bread is investigated.
Sourdough from lactic acid bacteria (Lb. plantarum, Lb. reuteri) with
different dough yield (250 and 300) is made and incubated at 30°C
for 20 hour, then added to dough in the ratio of 10, 20 and 30%
replacement. Breads that supplemented with Lb. plantarum
sourdough had lower phytic acid. Higher replacement of sourdough
and higher DY cause higher decrease in phytic acid content.
Sourdough from Lb. plantarum, DY = 300 and 30% replacement
cause the highest decrease in phytic acid content (49.63 mg/100g).
As indicated by panelists, Lb. reuteri sourdough can present the
greatest effect on overall quality score of the breads. DY reduction
cause a decrease in bread quality score. Sensory score of Toast bread
is 81.71 in the samples that treated with Lb. reuteri sourdough with
DY = 250 and 20% replacement.
Abstract: Purpose: To explore the use of Curvelet transform to
extract texture features of pulmonary nodules in CT image and support
vector machine to establish prediction model of small solitary
pulmonary nodules in order to promote the ratio of detection and
diagnosis of early-stage lung cancer. Methods: 2461 benign or
malignant small solitary pulmonary nodules in CT image from 129
patients were collected. Fourteen Curvelet transform textural features
were as parameters to establish support vector machine prediction
model. Results: Compared with other methods, using 252 texture
features as parameters to establish prediction model is more proper.
And the classification consistency, sensitivity and specificity for the
model are 81.5%, 93.8% and 38.0% respectively. Conclusion: Based
on texture features extracted from Curvelet transform, support vector
machine prediction model is sensitive to lung cancer, which can
promote the rate of diagnosis for early-stage lung cancer to some
extent.
Abstract: The efficient knowledge management system (KMS)
is one of the important strategies to help firms to achieve sustainable
competitive advantages, but little research has been conducted to
understand what contributes to the KMS success. This study thus set
to investigate the determinants of KMS success in the context of Thai
banking industry. A questionnaire survey was conducted in four
major Thai Banks to test the proposed KMS Success model.
The result of this study shows that KMS use and user satisfaction
relate significantly to the success of KMS, and knowledge quality,
service quality and trust lead to system use, and knowledge quality,
system quality and trust lead to user satisfaction. However, this
research focuses only on system and user-related factors. Future
research thus can extend to study factors such as management support
and organization readiness.
Abstract: The growing outsourcing of logistics services
resulting from the ongoing current in firms of costs
reduction/increased efficiency means that it is becoming more and
more important for the companies doing the outsourcing to carry out
a proper evaluation.
The multiple definitions and measures of logistics service
performance found in research on the topic create a certain degree of
confusion and do not clear the way towards the proper measurement
of their performance. Do a model and a specific set of indicators exist
that can be considered appropriate for measuring the performance of
logistics services outsourcing in industrial environments? Are said
indicators in keeping with the objectives pursued by outsourcing? We
aim to answer these and other research questions in the study we have
initiated in the field within the framework of the international High
Performance Manufacturing (HPM) project of which this paper
forms part.
As the first stage of this research, this paper reviews articles
dealing with the topic published in the last 15 years with the aim of
detecting the models most used to make this measurement and
determining which performance indicators are proposed as part of
said models and which are most used. The first steps are also taken in
determining whether these indicators, financial and operational, cover
the aims that are being pursued when outsourcing logistics services.
The findings show there is a wide variety of both models and
indicators used. This would seem to testify to the need to continue
with our research in order to try to propose a model and a set of
indicators for measuring the performance of logistics services
outsourcing in industrial environments.
Abstract: This paper describes a 3D modeling system in
Augmented Reality environment, named 3DARModeler. It can be
considered a simple version of 3D Studio Max with necessary
functions for a modeling system such as creating objects, applying
texture, adding animation, estimating real light sources and casting
shadows. The 3DARModeler introduces convenient, and effective
human-computer interaction to build 3D models by combining both
the traditional input method (mouse/keyboard) and the tangible input
method (markers). It has the ability to align a new virtual object with
the existing parts of a model. The 3DARModeler targets nontechnical
users. As such, they do not need much knowledge of
computer graphics and modeling techniques. All they have to do is
select basic objects, customize their attributes, and put them together
to build a 3D model in a simple and intuitive way as if they were
doing in the real world. Using the hierarchical modeling technique,
the users are able to group several basic objects to manage them as a
unified, complex object. The system can also connect with other 3D
systems by importing and exporting VRML/3Ds Max files. A
module of speech recognition is included in the system to provide
flexible user interfaces.
Abstract: Propagation of solitons in single-mode birefringent fibers is considered under the presence of third-order dispersion (TOD). The behavior of two neighboring solitons and their interaction is investigated under the presence of third-order dispersion with different group velocity dispersion (GVD) parameters. It is found that third-order dispersion makes the resultant soliton to deviate from its ideal position and increases the interaction between adjacent soliton pulses. It is also observed that this deviation due to third-order dispersion is considerably small when the optical pulse propagates at wavelengths relatively far from the zerodispersion. Modified coupled nonlinear Schrödinger-s equations (CNLSE) representing the propagation of optical pulse in single mode fiber with TOD are solved using split-step Fourier algorithm. The results presented in this paper reveal that the third-order dispersion can substantially increase the interaction between the solitons, but large group velocity dispersion reduces the interaction between neighboring solitons.
Abstract: A novel method of learning complex fuzzy decision regions in the n-dimensional feature space is proposed. Through the fuzzy decision regions, a given pattern's class membership value of every class is determined instead of the conventional crisp class the pattern belongs to. The n-dimensional fuzzy decision region is approximated by union of hyperellipsoids. By explicitly parameterizing these hyperellipsoids, the decision regions are determined by estimating the parameters of each hyperellipsoid.Genetic Algorithm is applied to estimate the parameters of each region component. With the global optimization ability of GA, the learned decision region can be arbitrarily complex.