Abstract: The objective of this project is to study the corrosion
behaviour and hardness based on the presence of martensite in dual
phase steel. This study was conducted on six samples of dual phase
steel which have different percentage of martensite. A total of 9
specimens were prepared by intercritical annealing process to study
the effect of temperature to the formation of martensite. The low
carbon steels specimens were heated for 25 minutes in a specified
temperature ranging from 7250C to 8250C followed by rapid cooling
in water. The measurement of corrosion rate was done by using
extrapolation tafel method, while potentiostat was used to control and
measured the current produced. This measurement is performed
through a system named CMS105. The result shows that a specimen
with higher percentage of martensite is likely to corrode faster.
Hardness test for each specimen was conducted to compare its
hardness with low carbon steel. The results obtained indicate that the
specimen hardness is proportional to the amount of martensite in dual
phase steel.
Abstract: According to the increasing utilization in power system, the transmission lines and power plants often operate in stability boundary and system probably lose its stable condition by over loading or occurring disturbance. According to the reasons that are mentioned, the prediction and recognition of voltage instability in power system has particular importance and it makes the network security stronger.This paper, by considering of power system contingencies based on the effects of them on Mega Watt Margin (MWM) and maximum loading point is focused in order to analyse the static voltage stability using continuation power flow method. The study has been carried out on IEEE 14-Bus Test System using Matlab and Psat softwares and results are presented.
Abstract: In this paper we propose a new classification method for automatic sleep scoring using an artificial neural network based decision tree. It attempts to treat sleep scoring progress as a series of two-class problems and solves them with a decision tree made up of a group of neural network classifiers, each of which uses a special feature set and is aimed at only one specific sleep stage in order to maximize the classification effect. A single electroencephalogram (EEG) signal is used for our analysis rather than depending on multiple biological signals, which makes greatly simplifies the data acquisition process. Experimental results demonstrate that the average epoch by epoch agreement between the visual and the proposed method in separating 30s wakefulness+S1, REM, S2 and SWS epochs was 88.83%. This study shows that the proposed method performed well in all the four stages, and can effectively limit error propagation at the same time. It could, therefore, be an efficient method for automatic sleep scoring. Additionally, since it requires only a small volume of data it could be suited to pervasive applications.
Abstract: We explore entanglement in composite quantum systems
and how its peculiar properties are exploited in quantum
information and communication protocols by means of Diagrams
of States, a novel method to graphically represent and analyze how
quantum information is elaborated during computations performed
by quantum circuits.
We present quantum diagrams of states for Bell states generation,
measurements and projections, for dense coding and quantum teleportation,
for probabilistic quantum machines designed to perform
approximate quantum cloning and universal NOT and, finally, for
quantum privacy amplification based on entanglement purification.
Diagrams of states prove to be a useful approach to analyze quantum
computations, by offering an intuitive graphic representation of the
processing of quantum information. They also help in conceiving
novel quantum computations, from describing the desired information
processing to deriving the final implementation by quantum gate
arrays.
Abstract: The residue number system (RNS) is popular in high performance computation applications because of its carry-free nature. The challenges of RNS systems design lie in the moduli set selection and in the reverse conversion from residue representation to weighted representation. In this paper, we proposed a fully parallel reverse conversion algorithm for the moduli set {rn - 2, rn - 1, rn}, based on simple mathematical relationships. Also an efficient hardware realization of this algorithm is presented. Our proposed converter is very faster and results to hardware savings, compared to the other reverse converters.
Abstract: Nowadays, more engineering systems are using some
kind of Artificial Intelligence (AI) for the development of their
processes. Some well-known AI techniques include artificial neural
nets, fuzzy inference systems, and neuro-fuzzy inference systems
among others. Furthermore, many decision-making applications base
their intelligent processes on Fuzzy Logic; due to the Fuzzy
Inference Systems (FIS) capability to deal with problems that are
based on user knowledge and experience. Also, knowing that users
have a wide variety of distinctiveness, and generally, provide
uncertain data, this information can be used and properly processed
by a FIS. To properly consider uncertainty and inexact system input
values, FIS normally use Membership Functions (MF) that represent
a degree of user satisfaction on certain conditions and/or constraints.
In order to define the parameters of the MFs, the knowledge from
experts in the field is very important. This knowledge defines the MF
shape to process the user inputs and through fuzzy reasoning and
inference mechanisms, the FIS can provide an “appropriate" output.
However an important issue immediately arises: How can it be
assured that the obtained output is the optimum solution? How can it
be guaranteed that each MF has an optimum shape? A viable solution
to these questions is through the MFs parameter optimization. In this
Paper a novel parameter optimization process is presented. The
process for FIS parameter optimization consists of the five simple
steps that can be easily realized off-line. Here the proposed process
of FIS parameter optimization it is demonstrated by its
implementation on an Intelligent Interface section dealing with the
on-line customization / personalization of internet portals applied to
E-commerce.
Abstract: Research on the boron (B) toxicity problems had recently considerable relation, especially in the dry regions of the world. Development of resistant varieties to B toxicity is a high priority on these regions, where the soils have high levels of B. Thus, this study aimed to assessment the resistance of wheat genotypes to B toxicity using the agronomic and physiologic parameters. For this aim, a pot experiment, based on a completely randomized design with three replications, was conducted using the soil of calcareous usthochrepts. In the study, twenty different wheat genotypes of T. aestivum and T. Durum were used. Boron fertilizer at the levels of 0 (-B), 30 mg B kg-1 (+B) as H3BO3 was applied to the pots. After harvest, plant dry matter yield was recorded, and total B concentrations in tops of wheat plants were determined. The results have revealed the existence of a large genotypic variation among wheat genotypes to their physiologic and agronomic susceptibility to B toxicity.
Abstract: A challenged control problem is when the
performance is pushed to the limit. The state-derivative feedback
control strategy directly uses acceleration information for feedback
and state estimation. The derivative part is concerned with the rateof-
change of the error with time. If the measured variable approaches
the set point rapidly, then the actuator is backed off early to allow it
to coast to the required level. Derivative action makes a control
system behave much more intelligently. A sensor measures the
variable to be controlled and the measured in formation is fed back to
the controller to influence the controlled variable. A high gain
problem can be also formulated for proportional plus derivative
feedback transformation. Using MATLAB Simulink dynamic
simulation tool this paper examines a system with a proportional plus
derivative feedback and presents an automatic implementation of
finding an acceptable controlled system. Using feedback
transformations the system is transformed into another system.
Abstract: The purpose of this study is to analyze the visual
preference of patterns in pedestrian roads. In this study, animation was
applied for the estimation of dynamic streetscape. Six patterns of
pedestrian were selected in order to analyze the visual preference. The
shapes are straight, s-curve, and zigzag. The ratio of building's height
and road's width are 2:1 and 1:1. Twelve adjective pairs used in the
field investigation were selected from adjectives which are used
usually in the estimation of streetscape. They are interesting-boring,
simple-complex, calm-noisy, open-enclosed, active-inactive,
lightly-depressing, regular-irregular, unique-usual, rhythmic-not
rhythmic, united-not united, stable-unstable, tidy-untidy.
Dynamic streetscape must be considered important in pedestrian
shopping mall and park because it will be an attraction. So, s-curve
pedestrian road, which is the most beautiful as a result of this study,
should be designed in this area. Also, the ratio of building's height and
road's width along pedestrian road should be reduced.
Abstract: Over the early years of the 21st century, cities
throughout the Middle East, particularly in the Gulf region have
expanded more rapidly than ever before. Given the presence of a
large volume of high-rise buildings allover the region, the local
authority aims to set a new standard for sustainable development;
with an integrated approach to maintain a balance between economy,
quality, environmental protection and safety of life. In the very near
future, as mandatory requirements, sustainability will be the criteria
that should be included in all building projects. It is well known in
the building sustainability topics that structural design engineers do
not have a key role in this matter. In addition, the LEED (Leadership
in Energy and Environmental Design) has looked almost exclusively
on the environmental components and materials specifications. The
objective of this paper is to focus and establish groundwork for
sustainability techniques and applications related to the RC high-rise
buildings design, from the structural point of view. A set of
recommendations related to local conditions, structural modeling and
analysis is given, and some helpful suggestions for structural design
team work are addressed. This paper attempts to help structural
engineers in identifying the building sustainability design, in order to
meet local needs and achieve alternative solutions at an early stage of
project design.
Abstract: Petroglyphs, stone sculptures, burial mounds, and
other memorial religious structures are ancient artifacts which find
reflection in contemporary world culture, including the culture of
Kazakhstan. In this article, the problem of the influence of ancient
artifacts on contemporary culture is researched, using as an example
Kazakhstan-s sculpture and painting. The practice of creating
petroglyphs, stone sculptures, and memorial religious structures was
closely connected to all fields of human existence, which fostered the
formation of and became an inseparable part of a traditional
worldview. The ancient roots of Saka-Sythian and Turkic nomadic
culture have been studied, and integrated into the foundations of the
contemporary art of Kazakhstan. The study of the ancient cultural
heritage of Kazakhstan by contemporary artists, sculptors and
architects, as well as the influence of European art and cultures on the
art of Kazakhstan are furthering the development of a new national
art.
Abstract: Chromite is one of the principal ore of chromium in which the metal exists as a complex oxide (FeO.Cr2O3).The prepared chromite can be widely used as refractory in high temperature applications. This study describes the use of local chromite ore as refractory material. To study the feasibility of local chromite, chemical analysis and refractoriness are firstly measured. To produce chromite refractory brick, it is pressed under a press of 400 tons, dried and fired at 1580°C for fifty two hours. Then, the standard properties such as cold crushing strength, apparent porosity, apparent specific gravity, bulk density and water absorption that the chromite brick should possess were measured. According to the results obtained, the brick made by local chromite ore was suitable for use as refractory brick.
Abstract: Jatropha curcas stem was analyzed for chemical
compositions: 19.11% pentosan, 42.99% alphacellulose and 24.11%
lignin based on dry weight of 100-g raw material. The condition to
fractionate cellulose, hemicellulose and lignin in J. curcas stem using
steam explosion was optimized. The procedure started from cutting J.
curcas stem into small pieces and soaked in water for overnight.
After that, they were steam exploded at 214 °C and 21 kg/cm2 for 5
min. The obtained hydrolysate contained 1.55 g/L ferulic acid which
after that was used as substrate for vanillin production by Aspergillus
niger and Pycnoporus cinnabarinus in one-step process. The
maximum 0.65 g/L of vanillin were obtained with the conversion rate
of 45.2% based on the initial ferulic acid.
Abstract: Most known methods for measuring the structural similarity of document structures are based on, e.g., tag measures, path metrics and tree measures in terms of their DOM-Trees. Other methods measures the similarity in the framework of the well known vector space model. In contrast to these we present a new approach to measuring the structural similarity of web-based documents represented by so called generalized trees which are more general than DOM-Trees which represent only directed rooted trees.We will design a new similarity measure for graphs representing web-based hypertext structures. Our similarity measure is mainly based on a novel representation of a graph as strings of linear integers, whose components represent structural properties of the graph. The similarity of two graphs is then defined as the optimal alignment of the underlying property strings. In this paper we apply the well known technique of sequence alignments to solve a novel and challenging problem: Measuring the structural similarity of generalized trees. More precisely, we first transform our graphs considered as high dimensional objects in linear structures. Then we derive similarity values from the alignments of the property strings in order to measure the structural similarity of generalized trees. Hence, we transform a graph similarity problem to a string similarity problem. We demonstrate that our similarity measure captures important structural information by applying it to two different test sets consisting of graphs representing web-based documents.
Abstract: It has proved that nonlinear diffusion and bilateral
filtering (BF) have a closed connection. Early effort and contribution
are to find a generalized representation to link them by using adaptive
filtering. In this paper a new further relationship between nonlinear
diffusion and bilateral filtering is explored which pays more attention
to numerical calculus. We give a fresh idea that bilateral filtering can
be accelerated by multigrid (MG) scheme which likes the nonlinear
diffusion, and show that a bilateral filtering process with large kernel
size can be approximated by a nonlinear diffusion process based on
full multigrid (FMG) scheme.
Abstract: Value-based group decision is very complicated since many parties involved. There are different concern caused by differing preferences, experiences, and background. Therefore, a support system is required to enable each stakeholder to evaluate and rank the solution alternatives before engaging into negotiation with the other stakeholders. The support system is based on combination between value-based analysis, multi criteria group decision making based on satisfying options, and negotiation process based on coalition formation. This paper presents the group decision and negotiation on the selection of suitable material for a support bridge structure involving three decision makers, who are an estate manager, a project manager, and an engineer. There are three alternative solutions for the material of the support bridge structure, which are (a1) steel structure, (a2) reinforced concrete structure and (a3) wooden structure.
Abstract: Today advertising is actively penetrating into many spheres of our lives. We cannot imagine the existence of a lot of economic activities without advertising. That mostly concerns trade and services. Everyone of us should look better into the everyday communication and carefully consider the amount and the quality of the information we receive as well as its influence on our behaviour. Special attention should be paid to the young generation. Theoretical and practical research has proved the ever growing influence of information (especially the one contained in advertising) on a society; on its economics, culture, religion, politics and even people-s private lives and behaviour. Children have plenty of free time and, therefore, see a lot of different advertising. Though education of children is in the hands of parents and schools, advertising makers and customers should think with responsibility about the selection of time and transmission channels of child targeted advertising. The purpose of the present paper is to investigate the influence of advertising upon consumer views and behaviour of children in different age groups. The present investigation has clarified the influence of advertising as a means of information on a certain group of society, which in the modern information society is the most vulnerable – children. In this paper we assess children-s perception and their understanding of advertising.
Abstract: People at workplace always face with stress and feel it in their lives. There are many factors that create stress and mobbing is one of them. Mobbing is a psychological terror, conducted systematically toward an individual by others at the same workplace. Mobbing started to become a famous subject last years in U.S and Europe. In Turkey, it is a new concept not because it does not occur, because of human nature that does not allow confessing it. Mobbing is being ignored by people, organizations and also government in our country. The focus of this study will be mobbing in Turkey by examining the workplace mobbing among Turkish academicians. There are other studies about mobbing in Turkey but none of them studied academy. Because mobbing methods change according to sectors and occupations, it is important to analyze each sector to understand the methods used in mobbing and the reactions of victims to these actions. The concept is analyzed in detail before focusing on mobbing at universities. This paper will be unique because there is no information about this specific subject in Turkish literature. In this paper, both qualitative and quantitative methods will be used to describe the mobbing at Turkish academic environment.
Abstract: Devices in a pervasive computing system (PCS) are characterized by their context-awareness. It permits them to provide proactively adapted services to the user and applications. To do so, context must be well understood and modeled in an appropriate form which enhance its sharing between devices and provide a high level of abstraction. The most interesting methods for modeling context are those based on ontology however the majority of the proposed methods fail in proposing a generic ontology for context which limit their usability and keep them specific to a particular domain. The adaptation task must be done automatically and without an explicit intervention of the user. Devices of a PCS must acquire some intelligence which permits them to sense the current context and trigger the appropriate service or provide a service in a better suitable form. In this paper we will propose a generic service ontology for context modeling and a context-aware service adaptation based on a service oriented definition of context.
Abstract: Malaysia has successfully applied economic planning
to guide the development of the country from an economy of
agriculture and mining to a largely industrialised one. Now, with its
sights set on attaining the economic level of a fully developed nation
by 2020, the planning system must be made even more efficient and
focused.
It must ensure that every investment made in the country, contribute
towards creating the desirable objective of a strong, modern,
internationally competitive, technologically advanced, post-industrial
economy. Cities in Malaysia must also be fully aware of the enormous
competition it faces in a region with rapidly expanding and
modernising economies, all contending for the same pool of potential
international investments.
Efficiency of urban governance is also fundamental issue in
development characterized by sustainability, subsidiarity, equity,
transparency and accountability, civic engagement and citizenship, and
security. As described above, city competitiveness is harnessed
through 'city marketing and city management'.
High technology and high skilled industries, together with finance,
transportation, tourism, business, information and professional
services shopping and other commercial activities, are the principal
components of the nation-s economy, which must be developed to a
level well beyond where it is now. In this respect, Kuala Lumpur being
the premier city must play the leading role.