Abstract: This paper deals with stability analysis for synchronous reluctance motors drive. Special attention is paid to the transient performance with variations in motor's parameters such as Ld and Rs. A study of the dynamic control using d-q model is presented first in order to clarify the stability of the motor drive system. Based on the experimental parameters of the synchronous reluctance motor, this paper gives some simulation results using MATLAB/SIMULINK software packages. It is concluded that the motor parameters, especially Ld, affect the estimator stability and hence the whole drive system.
Abstract: A new reverse phase-high performance liquid chromatography (RP-HPLC) method with fluorescent detector (FLD) was developed and optimized for Norfloxacin determination in human plasma. Mobile phase specifications, extraction method and excitation and emission wavelengths were varied for optimization. HPLC system contained a reverse phase C18 (5 μm, 4.6 mm×150 mm) column with FLD operated at excitation 330 nm and emission 440 nm. The optimized mobile phase consisted of 14% acetonitrile in buffer solution. The aqueous phase was prepared by mixing 2g of citric acid, 2g sodium acetate and 1 ml of triethylamine in 1 L of Milli-Q water was run at a flow rate of 1.2 mL/min. The standard curve was linear for the range tested (0.156–20 μg/mL) and the coefficient of determination was 0.9978. Aceclofenac sodium was used as internal standard. A detection limit of 0.078 μg/mL was achieved. Run time was set at 10 minutes because retention time of norfloxacin was 0.99 min. which shows the rapidness of this method of analysis. The present assay showed good accuracy, precision and sensitivity for Norfloxacin determination in human plasma with a new internal standard and can be applied pharmacokinetic evaluation of Norfloxacin tablets after oral administration in human.
Abstract: this paper presents an auto-regressive network called the Auto-Regressive Multi-Context Recurrent Neural Network (ARMCRN), which forecasts the daily peak load for two large power plant systems. The auto-regressive network is a combination of both recurrent and non-recurrent networks. Weather component variables are the key elements in forecasting because any change in these variables affects the demand of energy load. So the AR-MCRN is used to learn the relationship between past, previous, and future exogenous and endogenous variables. Experimental results show that using the change in weather components and the change that occurred in past load as inputs to the AR-MCRN, rather than the basic weather parameters and past load itself as inputs to the same network, produce higher accuracy of predicted load. Experimental results also show that using exogenous and endogenous variables as inputs is better than using only the exogenous variables as inputs to the network.
Abstract: The Time-Domain Boundary Element Method (TDBEM)
is a well known numerical technique that handles quite
properly dynamic analyses considering infinite dimension media.
However, when these analyses are also related to nonlinear behavior,
very complex numerical procedures arise considering the TD-BEM,
which may turn its application prohibitive. In order to avoid this
drawback and model nonlinear infinite media, the present work
couples two BEM formulations, aiming to achieve the best of two
worlds. In this context, the regions expected to behave nonlinearly
are discretized by the Domain Boundary Element Method (D-BEM),
which has a simpler mathematical formulation but is unable to deal
with infinite domain analyses; the TD-BEM is employed as in the
sense of an effective non-reflexive boundary. An iterative procedure
is considered for the coupling of the TD-BEM and D-BEM, which is
based on a relaxed renew of the variables at the common interfaces.
Elastoplastic models are focused and different time-steps are allowed
to be considered by each BEM formulation in the coupled analysis.
Abstract: A bond graph model of an electrical transformer
including the nonlinear saturation is presented. A nonlinear observer for the transformer based on multivariable circle
criterion in the physical domain is proposed. In order to show the saturation and hysteresis effects on the electrical transformer,
simulation results are obtained. Finally, the paper describes that convergence of the estimates to the true states is achieved.
Abstract: The various types of frequent pattern discovery
problem, namely, the frequent itemset, sequence and graph mining
problems are solved in different ways which are, however, in certain
aspects similar. The main approach of discovering such patterns can
be classified into two main classes, namely, in the class of the levelwise
methods and in that of the database projection-based methods.
The level-wise algorithms use in general clever indexing structures
for discovering the patterns. In this paper a new approach is proposed
for discovering frequent sequences and tree-like patterns efficiently
that is based on the level-wise issue. Because the level-wise
algorithms spend a lot of time for the subpattern testing problem, the
new approach introduces the idea of using automaton theory to solve
this problem.
Abstract: Textile structures are engineered and fabricated to
meet worldwide structural applications. Nevertheless, research
varying textile structure on natural fibre as composite reinforcement
was found to be very limited. Most of the research is focusing on
short fibre and random discontinuous orientation of the reinforcement
structure. Realizing that natural fibre (NF) composite had been
widely developed to be used as synthetic fibre composite
replacement, this research attempted to examine the influence of
woven and cross-ply laminated structure towards its mechanical
performances. Laminated natural fibre composites were developed
using hand lay-up and vacuum bagging technique. Impact and
flexural strength were investigated as a function of fibre type (coir
and kenaf) and reinforcement structure (imbalanced plain woven,
0°/90° cross-ply and +45°/-45° cross-ply). Multi-level full factorial
design of experiment (DOE) and analysis of variance (ANOVA) was
employed to impart data as to how fibre type and reinforcement
structure parameters affect the mechanical properties of the
composites. This systematic experimentation has led to determination
of significant factors that predominant influences the impact and
flexural properties of the textile composites. It was proven that both
fibre type and reinforcement structure demonstrated significant
difference results. Overall results indicated that coir composite and
woven structure exhibited better impact and flexural strength. Yet,
cross-ply composite structure demonstrated better fracture resistance.
Abstract: In this paper the Huang-s method for solving a m×n fuzzy linear system when, m≤ n, is considered. The method in detail is discussed and illustrated by solving some numerical examples.
Abstract: The image segmentation method described in this
paper has been developed as a pre-processing stage to be used in
methodologies and tools for video/image indexing and retrieval by
content. This method solves the problem of whole objects extraction
from background and it produces images of single complete objects
from videos or photos. The extracted images are used for calculating
the object visual features necessary for both indexing and retrieval
processes.
The segmentation algorithm is based on the cooperation among an
optical flow evaluation method, edge detection and region growing
procedures. The optical flow estimator belongs to the class of
differential methods. It permits to detect motions ranging from a
fraction of a pixel to a few pixels per frame, achieving good results in
presence of noise without the need of a filtering pre-processing stage
and includes a specialised model for moving object detection.
The first task of the presented method exploits the cues from
motion analysis for moving areas detection. Objects and background
are then refined using respectively edge detection and seeded region
growing procedures. All the tasks are iteratively performed until
objects and background are completely resolved.
The method has been applied to a variety of indoor and outdoor
scenes where objects of different type and shape are represented on
variously textured background.
Abstract: The occurrence and removal of trace organic
contaminants in the aquatic environment has become a focus of
environmental concern. For the selective removal of carbamazepine
from loaded waters molecularly imprinted polymers (MIPs) were
synthesized with carbamazepine as template. Parameters varied were
the type of monomer, crosslinker, and porogen, the ratio of starting
materials, and the synthesis temperature. Best results were obtained
with a template to crosslinker ratio of 1:20, toluene as porogen, and
methacrylic acid (MAA) as monomer. MIPs were then capable to
recover carbamazepine by 93% from a 10-5 M landfill leachate
solution containing also caffeine and salicylic acid. By comparison,
carbamazepine recoveries of 75% were achieved using a nonimprinted
polymer (NIP) synthesized under the same conditions, but
without template. In landfill leachate containing solutions
carbamazepine was adsorbed by 93-96% compared with an uptake of
73% by activated carbon. The best solvent for desorption was
acetonitrile, with which the amount of solvent necessary and dilution
with water was tested. Selected MIPs were tested for their reusability
and showed good results for at least five cycles. Adsorption
isotherms were prepared with carbamazepine solutions in the
concentration range of 0.01 M to 5*10-6 M. The heterogeneity index
showed a more homogenous binding site distribution.
Abstract: The paper explores the development of an optimization of method and apparatus for retrieving extended high dynamic range from digital negative image. Architectural photo imaging can benefit from high dynamic range imaging (HDRI) technique for preserving and presenting sufficient luminance in the shadow and highlight clipping image areas. The HDRI technique that requires multiple exposure images as the source of HDRI rendering may not be effective in terms of time efficiency during the acquisition process and post-processing stage, considering it has numerous potential imaging variables and technical limitations during the multiple exposure process. This paper explores an experimental method and apparatus that aims to expand the dynamic range from digital negative image in HDRI environment. The method and apparatus explored is based on a single source of RAW image acquisition for the use of HDRI post-processing. It will cater the optimization in order to avoid and minimize the conventional HDRI photographic errors caused by different physical conditions during the photographing process and the misalignment of multiple exposed image sequences. The study observes the characteristics and capabilities of RAW image format as digital negative used for the retrieval of extended high dynamic range process in HDRI environment.
Abstract: Fine alignment of main ship power plants mechanisms
and shaft lines provides long-term and failure-free performance of
propulsion system while fast and high-quality installation of
mechanisms and shaft lines decreases common labor intensity. For
checking shaft line allowed stress and setting its alignment it is
required to perform calculations considering various stages of life
cycle. In 2012 JSC SSTC developed special software complex
“Shaftline” for calculation of alignment of having its own I/O
interface and display of shaft line 3D model. Alignment of shaft line
as per bearing loads is rather labor-intensive procedure. In order to
decrease its duration, JSC SSTC developed automated alignment
system from ship power plants mechanisms. System operation
principle is based on automatic simulation of design load on bearings.
Initial data for shaft line alignment can be exported to automated
alignment system from PC “Shaft line”.
Abstract: Program slicing is the task of finding all statements in
a program that directly or indirectly influence the value of a variable
occurrence. The set of statements that can affect the value of a
variable at some point in a program is called a program backward
slice. In several software engineering applications, such as program
debugging and measuring program cohesion and parallelism, several
slices are computed at different program points. The existing
algorithms for computing program slices are introduced to compute a
slice at a program point. In these algorithms, the program, or the
model that represents the program, is traversed completely or
partially once. To compute more than one slice, the same algorithm
is applied for every point of interest in the program. Thus, the same
program, or program representation, is traversed several times.
In this paper, an algorithm is introduced to compute all forward
static slices of a computer program by traversing the program
representation graph once. Therefore, the introduced algorithm is
useful for software engineering applications that require computing
program slices at different points of a program. The program
representation graph used in this paper is called Program Dependence
Graph (PDG).
Abstract: A homologous series of aromatic esters, 4-nalkanoyloxybenzylidene-
4--bromoanilines, nABBA,
consisting of two 1,4-disubstituted phenyl cores and a Schiff
base central linkage was synthesized. All the members can be
differed by the number of carbon atoms at terminal
alkanoyloxy chain (CnH2n-1COO-, n = 2, 6, 18). The molecular
structure of nABBA was confirmed with infrared
spectroscopy, nuclear magnetic resonance (NMR)
spectroscopy and electron-ionization mass (EI-MS)
spectrometry. Mesomorphic properties were studied using
differential scanning calorimetry and polarizing optical
microscopy.
Abstract: In this treatise we will study the capability of static
compensator for reactive power to stabilize sheen voltage with motor
loading on power networks system. We also explain the structure and main function of STATCOM and the method to control it using STATCOM transformer current to simultaneously predict after
telling about the necessity of FACTS tools to compensate in power networks. Then we study topology and controlling system to stabilize
voltage during start of inductive motor. The outcome of stimulat by MATLAB software supports presented controlling idea and
system in the treatise.
Abstract: one of the significant factors for improving the
accuracy of Land Surface Temperature (LST) retrieval is the correct
understanding of the directional anisotropy for thermal radiance. In
this paper, the multiple scattering effect between heterogeneous
non-isothermal surfaces is described rigorously according to the
concept of configuration factor, based on which a directional thermal
radiance model is built, and the directional radiant character for urban
canopy is analyzed. The model is applied to a simple urban canopy
with row structure to simulate the change of Directional Brightness
Temperature (DBT). The results show that the DBT is aggrandized
because of the multiple scattering effects, whereas the change range of
DBT is smoothed. The temperature difference, spatial distribution,
emissivity of the components can all lead to the change of DBT. The
“hot spot" phenomenon occurs when the proportion of high
temperature component in the vision field came to a head. On the other
hand, the “cool spot" phenomena occur when low temperature
proportion came to the head. The “spot" effect disappears only when
the proportion of every component keeps invariability. The model
built in this paper can be used for the study of directional effect on
emissivity, the LST retrieval over urban areas and the adjacency effect
of thermal remote sensing pixels.
Abstract: Problem-based learning (PBL) is one of the student
centered approaches and has been considered by a number of higher
educational institutions in many parts of the world as a method of
delivery. This paper presents a creative thinking approach for
implementing Problem-based Learning in Mechanics of Structure
within a Malaysian Polytechnics environment. In the learning
process, students learn how to analyze the problem given among the
students and sharing classroom knowledge into practice. Further,
through this course-s emphasis on problem-based learning, students
acquire creative thinking skills and professional skills as they tackle
complex, interdisciplinary and real-situation problems. Once the
creative ideas are generated, there are useful additional techniques
for tender ideas that will grow into a productive concept or solution.
The combination of creative skills and technical abilities will enable
the students to be ready to “hit-the-ground-running" and produce in
industry when they graduate.
Abstract: Three-dimensional geometric models have been used
to present architectural and engineering works, showing their final
configuration. When the clarification of a detail or the constitution of
a construction step in needed, these models are not appropriate. They
do not allow the observation of the construction progress of a
building. Models that could present dynamically changes of the
building geometry are a good support to the elaboration of projects.
Techniques of geometric modeling and virtual reality were used to
obtain models that could visually simulate the construction activity.
The applications explain the construction work of a cavity wall and a
bridge. These models allow the visualization of the physical
progression of the work following a planned construction sequence,
the observation of details of the form of every component of the
works and support the study of the type and method of operation of
the equipment applied in the construction. These models presented
distinct advantage as educational aids in first-degree courses in Civil
Engineering. The use of Virtual Reality techniques in the
development of educational applications brings new perspectives to
the teaching of subjects related to the field of civil construction.
Abstract: In recent years, new product development became more and more competitive and globalized, and the designing phase is critical for the product success. The concept of modularity can provide the necessary foundation for organizations to design products that can respond rapidly to market needs. The paper describes data structures and algorithms of intelligent Web-based system for modular design taking into account modules compatibility relationship and given design requirements. The system intelligence is realized by developed algorithms for choice of modules reflecting all system restrictions and requirements. The proposed data structure and algorithms are illustrated by case study of personal computer configuration. The applicability of the proposed approach is tested through a prototype of Web-based system.
Abstract: Structured catalysts formed from the growth of
zeolites on substrates is an area of increasing interest due to the
increased efficiency of the catalytic process, and the ability to
provide superior heat transfer and thermal conductivity for both
exothermic and endothermic processes.
However, the generation of structured catalysts represents a
significant challenge when balancing the relationship variables
between materials properties and catalytic performance, with the
Na2O, H2O and Al2O3 gel composition paying a significant role in
this dynamic, thereby affecting the both the type and range of
application.
The structured catalyst films generated as part of this
investigation have been characterised using a range of techniques,
including X-ray diffraction (XRD), Electron microscopy (SEM),
Energy Dispersive X-ray analysis (EDX) and Thermogravimetric
Analysis (TGA), with the transition from oxide-on-alloy wires to
hydrothermally synthesised uniformly zeolite coated surfaces being
demonstrated using both SEM and XRD. The robustness of the
coatings has been ascertained by subjecting these to thermal cycling
(ambient to 550oC), with the results indicating that the synthesis time
and gel compositions have a crucial effect on the quality of zeolite
growth on the FeCrAlloy wires.
Finally, the activity of the structured catalyst was verified by a
series of comparison experiments with standard zeolite Y catalysts in
powdered pelleted forms.