Abstract: Highly ordered TiO2 nanotube (TNT) arrays were
fabricated onto a pre-treated titanium foil by anodic oxidation with a
voltage of 20V in phosphoric acid/sodium fluoride electrolyte. A pretreatment
of titanium foil involved washing with acetone,
isopropanol, ethanol and deionized water. Carbon doped TiO2
nanotubes (C-TNT) was fabricated 'in-situ' with the same method in
the presence of polyvinyl alcohol and urea as carbon sources. The
affects of polyvinyl alcohol concentration and oxidation time on the
composition, morphology and structure of the C-TN were studied by
FE-SEM, EDX and XRD techniques. FESEM images of the
nanotubes showed uniform arrays of C-TNTs. The density and
microstructures of the nanotubes were greatly affected by the content
of PVA. The introduction of the polyvinyl alcohol into the electrolyte
increases the amount of C content inside TiO2 nanotube arrays
uniformly. The influence of carbon content on the photo-current of
C-TNT was investigated and the I-V profiles of the nanotubes were
established. The preliminary results indicated that the 'in-situ'
doping technique produced a superior quality nanotubes compared to
post doping techniques.
Abstract: Fermented beverages have high expression in the
market for beverages in general, is increasingly valued in situations
where the characteristic aroma and flavor of the material that gave
rise to them are kept after processing. This study aimed to develop a
distilled beverage from passion fruit, and assess, by sensory tests and
chromatographic profile, the influence of different treatments (FM1-
spirit with pulp addiction and FM2 – spirit with bigger ratio of pulp
in must) in the setting of volatiles in the fruit drink, and performing
chemical characterization taking into account the main parameters of
quality established by the legislation. The chromatograms and the
first sensorial tests had indicated that sample FM1 possess better
characteristics of aroma, as much of how much quantitative the
qualitative point of view. However, it analyzes it sensorial end
(preference test) disclosed the biggest preference of the cloth provers
for sample FM2-2 (note 7.93), being the attributes of decisive color
and flavor in this reply, confirmed for the observed values lowest of
fixed and total acidity in the samples of treatment FM2.
Abstract: Technology changes have been acknowledged as a
critical factor in determining competitiveness of organization. Under
such environment, the right anticipation of technology change has
been of huge importance in strategic planning. To monitor technology
change, technology forecasting (TF) is frequently utilized. In
academic perspective, TF has received great attention for a long time.
However, few researches have been conducted to provide overview of
the TF literature. Even though some studies deals with review of TF
research, they generally focused on type and characteristics of various
TF, so hardly provides information about patterns of TF research and
which TF method is used in certain technology industry. Accordingly,
this study profile developments in and patterns of scholarly research in
TF over time. Also, this study investigates which technology
industries have used certain TF method and identifies their
relationships. This study will help in understanding TF research trend
and their application area.
Abstract: In the traditional theory of non-uniform torsion the
axial displacement field is expressed as the product of the unit twist
angle and the warping function. The first one, variable along the
beam axis, is obtained by a global congruence condition; the second
one, instead, defined over the cross-section, is determined by solving
a Neumann problem associated to the Laplace equation, as well as for
the uniform torsion problem.
So, as in the classical theory the warping function doesn-t punctually
satisfy the first indefinite equilibrium equation, the principal aim of
this work is to develop a new theory for non-uniform torsion of
beams with axial symmetric cross-section, fully restrained on both
ends and loaded by a constant torque, that permits to punctually
satisfy the previous equation, by means of a trigonometric expansion
of the axial displacement and unit twist angle functions.
Furthermore, as the classical theory is generally applied with good
results to the global and local analysis of ship structures, two beams
having the first one an open profile, the second one a closed section,
have been analyzed, in order to compare the two theories.
Abstract: This paper undertakes the problem of optimal
capacitor placement in a distribution system. The problem is how to
optimally determine the locations to install capacitors, the types and
sizes of capacitors to he installed and, during each load level,the
control settings of these capacitors in order that a desired objective
function is minimized while the load constraints,network constraints
and operational constraints (e.g. voltage profile) at different load
levels are satisfied. The problem is formulated as a combinatorial
optimization problem with a nondifferentiable objective function.
Four solution mythologies based on algorithms (GA),tabu search
(TS), and hybrid GA-SA algorithms are presented.The solution
methodologies are preceded by a sensitivity analysis to select the
candidate capacitor installation locations.
Abstract: The state of the art in instructional design for
computer-assisted learning has been strongly influenced by advances
in information technology, Internet and Web-based systems. The
emphasis of educational systems has shifted from training to
learning. The course delivered has also been changed from large
inflexible content to sequential small chunks of learning objects. The
concepts of learning objects together with the advanced technologies
of Web and communications support the reusability, interoperability,
and accessibility design criteria currently exploited by most learning
systems. These concepts enable just-in-time learning. We propose to
extend theses design criteria further to include the learnability
concept that will help adapting content to the needs of learners. The
learnability concept offers a better personalization leading to the
creation and delivery of course content more appropriate to
performance and interest of each learner. In this paper we present a
new framework of learning environments containing knowledge
discovery as a tool to automatically learn patterns of learning
behavior from learners' profiles and history.
Abstract: None of the processing models in the software
development has explained the software systems performance
evaluation and modeling; likewise, there exist uncertainty in the
information systems because of the natural essence of requirements,
and this may cause other challenges in the processing of software
development. By definition an extended version of UML (Fuzzy-
UML), the functional requirements of the software defined
uncertainly would be supported. In this study, the behavioral
description of uncertain information systems by the aid of fuzzy-state
diagram is crucial; moreover, the introduction of behavioral diagrams
role in F-UML is investigated in software performance modeling
process. To get the aim, a fuzzy sub-profile is used.
Abstract: In this paper, Lattice Boltzmann Method (LBM) is used to study laminar flow with mixed convection heat transfer inside a two-dimensional inclined lid-driven rectangular cavity with aspect ratio AR = 3. Bottom wall of the cavity is maintained at lower temperature than the top lid, and its vertical walls are assumed insulated. Top lid motion results in fluid motion inside the cavity. Inclination of the cavity causes horizontal and vertical components of velocity to be affected by buoyancy force. To include this effect, calculation procedure of macroscopic properties by LBM is changed and collision term of Boltzmann equation is modified. A computer program is developed to simulate this problem using BGK model of lattice Boltzmann method. The effects of the variations of Richardson number and inclination angle on the thermal and flow behavior of the fluid inside the cavity are investigated. The results are presented as velocity and temperature profiles, stream function contours and isotherms. It is concluded that LBM has good potential to simulate mixed convection heat transfer problems.
Abstract: This paper presents a method for the optimal
allocation of Distributed generation in distribution systems. In this
paper, our aim would be optimal distributed generation allocation for
voltage profile improvement and loss reduction in distribution
network. Genetic Algorithm (GA) was used as the solving tool,
which referring two determined aim; the problem is defined and
objective function is introduced. Considering to fitness values
sensitivity in genetic algorithm process, there is needed to apply load
flow for decision-making. Load flow algorithm is combined
appropriately with GA, till access to acceptable results of this
operation. We used MATPOWER package for load flow algorithm
and composed it with our Genetic Algorithm. The suggested method
is programmed under MATLAB software and applied ETAP
software for evaluating of results correctness. It was implemented on
part of Tehran electricity distributing grid. The resulting operation of
this method on some testing system is illuminated improvement of
voltage profile and loss reduction indexes.
Abstract: In the present article, effect of non-uniform excitation
of reservoir bottom on nonlinear response of concrete gravity dams is
considered. Anisotropic damage mechanics approach is used to model nonlinear behavior of mass concrete in 2D space. The tallest
monolith of Pine Flat dam is selected as a case study. The horizontal
and vertical components of 1967 Koyna earthquake is used to excite
the system. It is found that crest response and stresses within the dam body decrease significantly when the reservoir is excited nonuniformly. In addition, the crack profiles within the dam body and in vicinity of the neck decreases.
Abstract: This paper presents the effect of corrugation profile
geometry on the crushing behavior, energy absorption, failure
mechanism, and failure mode of woven roving glass fibre/epoxy
laminated composite tube. Experimental investigations were carried
out on composite tubes with three different profile shapes: sinusoidal,
triangular and trapezoidal. The tubes were subjected to lateral
compressive loading. On the addition to a radial corrugated
composite tube, cylindrical composite tube, were fabricated and
tested under the same condition in order to know the effect of
corrugation geometry. Typical histories of their deformation are
presented. Behavior of tubes as regards the peak crushing load,
energy absorbed and mode of crushing has been discussed. The
results show that the behavior of the tube under lateral compression
load is influenced by the geometry of the tube itself.
Abstract: In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and quasistationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical substantiation of these methods is proved by appropriate theorems. For it, converging quadrature processes have been developed and the estimations of errors in the terms of A.Ziqmound continuity modules have been received. For visualization of profiles are used: the method of the least squares with automatic conjecture, device spline, smooth replenishment and neural nets. Boundary conditions of heat exchange are determined from the solution of the corresponding integral equations and empirical relationships. The reliability of designed methods is proved by calculation and experimental investigations heat and hydraulic characteristics of the gas turbine first stage nozzle blade.
Abstract: In present work the problem of the ITER fusion
plasma neutron source parameter reconstruction using only the
Vertical Neutron Camera data was solved. The possibility of neutron
source parameter reconstruction was estimated by the numerical
simulations and the analysis of adequateness of mathematic model
was performed. The neutron source was specified in a parametric
form. The numerical analysis of solution stability with respect to data
distortion was done. The influence of the data errors on the
reconstructed parameters is shown:
• is reconstructed with errors less than 4% at all examined values
of δ (until 60%);
• is determined with errors less than 10% when δ do not overcome
5%;
• is reconstructed with relative error more than 10 %;
• integral intensity of the neutron source is determined with error
10% while δ error is less than 15%;
where -error of signal measurements, (R0,Z0), the plasma center
position,- /parameter of neutron source profile.
Abstract: This paper presents the study of induced currents and
temperature distribution in gear heated by induction process using 2D
finite element (FE) model. The model is developed by coupling
Maxwell and heat transfer equations into a multi-physics model. The
obtained results allow comparing the medium frequency (MF) and
high frequency (HF) cases and the effect of machine parameters on
the evolution of induced currents and temperature during heating.
The sensitivity study of the temperature profile is conducted and the
case hardness is predicted using the final temperature profile. These
results are validated using tests and give a good understanding of
phenomena during heating process.
Abstract: In this work, we incorporated a quartic bond potential
into a coarse-grained bead-spring model to study lubricant adsorption
on a solid surface as well as depletion instability. The surface tension
density and the number density profiles were examined to verify the
solid-liquid and liquid-vapor interfaces during heat treatment. It was
found that both the liquid-vapor interfacial thickness and the
solid-vapor separation increase with the temperatureT* when T*is
below the phase transition temperature Tc
*. At high temperatures
(T*>Tc
*), the solid-vapor separation decreases gradually as the
temperature increases. In addition, we evaluated the lubricant weight
and bond loss profiles at different temperatures. It was observed that
the lubricant desorption is favored over decomposition and is the main
cause of the lubricant failure at the head disk interface in our
simulations.
Abstract: In contrast to existing methods which do not take into account multiconnectivity in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM and FDM) numerical methods of calculation of stationary and quasi-stationary temperature field of a profile part of a blade with convective cooling (from the point of view of realization on PC). The theoretical substantiation of these methods is proved by appropriate theorems. For it, converging quadrature processes have been developed and the estimations of errors in the terms of A.Ziqmound continuity modules have been received. For visualization of profiles are used: the method of the least squares with automatic conjecture, device spline, smooth replenishment and neural nets. Boundary conditions of heat exchange are determined from the solution of the corresponding integral equations and empirical relationships. The reliability of designed methods is proved by calculation and experimental investigations heat and hydraulic characteristics of the gas turbine first stage nozzle blade.
Abstract: Losses reduction initiatives in distribution systems
have been activated due to the increasing cost of supplying
electricity, the shortage in fuel with ever-increasing cost to produce
more power, and the global warming concerns. These initiatives have
been introduced to the utilities in shape of incentives and penalties.
Recently, the electricity distribution companies in Oman have been
incentivized to reduce the distribution technical and non-technical
losses with an equal annual reduction rate for 6 years. In this paper,
different techniques for losses reduction in Mazoon Electricity
Company (MZEC) are addressed. In this company, high numbers of
substation and feeders were found to be non-compliant with the
Distribution System Security Standard (DSSS). Therefore, 33
projects have been suggested to bring non-complying 29 substations
and 28 feeders to meet the planed criteria and to comply with the
DSSS. The largest part of MZEC-s network (South Batinah region)
was modeled by ETAP software package. The model has been
extended to implement the proposed projects and to examine their
effects on losses reduction. Simulation results have shown that the
implementation of these projects leads to a significant improvement
in voltage profile, and reduction in the active and the reactive power
losses. Finally, the economical analysis has revealed that the
implementation of the proposed projects in MZEC leads to an annual
saving of about US$ 5 million.
Abstract: As the Internet continues to grow at a rapid pace as
the primary medium for communications and commerce and as
telecommunication networks and systems continue to expand their
global reach, digital information has become the most popular and
important information resource and our dependence upon the
underlying cyber infrastructure has been increasing significantly.
Unfortunately, as our dependency has grown, so has the threat to the
cyber infrastructure from spammers, attackers and criminal
enterprises. In this paper, we propose a new machine learning based
network intrusion detection framework for cyber security. The
detection process of the framework consists of two stages: model
construction and intrusion detection. In the model construction stage,
a semi-supervised machine learning algorithm is applied to a
collected set of network audit data to generate a profile of normal
network behavior and in the intrusion detection stage, input network
events are analyzed and compared with the patterns gathered in the
profile, and some of them are then flagged as anomalies should these
events are sufficiently far from the expected normal behavior. The
proposed framework is particularly applicable to the situations where
there is only a small amount of labeled network training data
available, which is very typical in real world network environments.
Abstract: A new technique to quantify the differential mode
delay (DMD) in multimode fiber (MMF) is been presented. The
technique measures DMD based on angular launch and
measurements of the difference in modal delay using variable
apertures at the fiber face. The result of the angular spatial filtering
revealed less excitation of higher order modes when the laser beam is
filtered at higher angles. This result would indicate that DMD
profiles would experience a data pattern dependency.
Abstract: Aerial and satellite images are information rich. They are also complex to analyze. For GIS systems, many features require fast and reliable extraction of roads and intersections. In this paper, we study efficient and reliable automatic extraction algorithms to address some difficult issues that are commonly seen in high resolution aerial and satellite images, nonetheless not well addressed in existing solutions, such as blurring, broken or missing road boundaries, lack of road profiles, heavy shadows, and interfering surrounding objects. The new scheme is based on a new method, namely reference circle, to properly identify the pixels that belong to the same road and use this information to recover the whole road network. This feature is invariable to the shape and direction of roads and tolerates heavy noise and disturbances. Road extraction based on reference circles is much more noise tolerant and flexible than the previous edge-detection based algorithms. The scheme is able to extract roads reliably from images with complex contents and heavy obstructions, such as the high resolution aerial/satellite images available from Google maps.