Abstract: The classic problem of recovering arbitrary values of
a band-limited signal from its samples has an added complication
in software radio applications; namely, the resampling calculations
inevitably fold aliases of the analog signal back into the original
bandwidth. The phenomenon is quantified by the spur-free dynamic
range. We demonstrate how a novel application of the Remez (Parks-
McClellan) algorithm permits optimal signal recovery and SFDR, far
surpassing state-of-the-art resamplers.
Abstract: To simulate heating systems in buildings, a research oriented computer code has been developed in Sharif University of Technology in Iran where the climate, existing heating equipment in buildings, consumer behavior and their interactions are considered for simulating energy consumption in conventional systems such as heaters, radiators and fan-coils. In order to validate the computer code, the available data of five buildings was used and the computed consumed energy was compared with the estimated energy extracted from monthly bills. The initial heating system was replaced by the alternative system and the effect of this change was observed on the energy consumption. As a result, the effect of changing heating equipment on energy consumption was investigated in different climates. Changing heater to radiator renders energy conservation up to 50% in all climates and changing radiator to fan-coil decreases energy consumption in climates with cold and dry winter.
Abstract: This paper presents the design and implementation of a fully integrated transimpedance amplifier (TIA) as the analog frontend receiver for Capacitive Micromachined Ultrasound Transducers (CMUTs) for ultrasound biomicroscope imaging application. The amplifier is designed to amplify the received signals from 17.5MHz to 52.5MHz with a center frequency of 35MHz. The TIA was fabricated in GF 0.18μm 1P6M 30V high voltage process. The measurement results show that the designed amplifier can reach a transimpedance gain of 61.08dBΩ and operating frequency from 17.5MHz to 100MHz with 1VP-P output voltage under 6V power supply.
Abstract: Sorghum flour was supplemented with 15 and 30%
chickpea flour. Sorghum flour and the supplement were fermented at
35 oC for 0, 8, 16, and 24 h. Changes in pH, titrable acidity, total
soluble solids, protein content, in vitro protein digestibility and
amino acid composition were investigated during fermentation and/or
after supplementation of sorghum flour with chickpea. The pH of the
fermenting material decreased sharply with a concomitant increase in
the titrable acidity. The total soluble solids remained unchanged with
progressive fermentation time. The protein content of sorghum
cultivar was found to be 9.27 and that of chickpea was 22.47%. The
protein content of sorghum cultivar after supplementation with15 and
30% chickpea was significantly (P ≤ 0.05) increased to 11.78 and
14.55%, respectively. The protein digestibility also increased after
fermentation from 13.35 to 30.59 and 40.56% for the supplements,
respectively. Further increment in protein content and digestibility
was observed when supplemented and unsupplemented samples were
fermented for different periods of time. Cooking of fermented
samples was found to increase the protein content slightly and
decreased digestibility for both supplements. Amino acid content of
fermented and fermented and cooked supplements was determined.
Supplementation was found to increase the lysine and therionine
content. Cooking following fermentation decreased lysine,
isoleucine, valine and sulfur containg amino acids.
Abstract: We propose a multi-agent based utilitarian approach
to model and understand information flows in social networks that
lead to Pareto optimal informational exchanges. We model the
individual expected utility function of the agents to reflect the net
value of information received. We show how this model, adapted
from a theorem by Karl Borch dealing with an actuarial Risk
Exchange concept in the Insurance industry, can be used for social
network analysis. We develop a utilitarian framework that allows us
to interpret Pareto optimal exchanges of value as potential
information flows, while achieving a maximization of a sum of
expected utilities of information of the group of agents. We examine
some interesting conditions on the utility function under which the
flows are optimal. We illustrate the promise of this new approach to
attach economic value to information in networks with a synthetic
example.
Abstract: CFD simulations are carried out in arterial stenoses
with 48 % areal occlusion. Non-newtonian fluid model is selected for
the blood flow as the same problem has been solved before with
Newtonian fluid model. Studies on flow resistance with the presence
of surface irregularities are carried out. Investigations are also
performed on the pressure drop at various Reynolds numbers. The
present study revealed that the pressure drop across a stenosed artery
is practically unaffected by surface irregularities at low Reynolds
numbers, while flow features are observed and discussed at higher
Reynolds numbers.
Abstract: Efficient utilization of existing water is a pressing
need for Pakistan. Due to rising population, reduction in present
storage capacity and poor delivery efficiency of 30 to 40% from
canal. A study to evaluate an irrigation system in the cotton-wheat
zone of Pakistan, after the watercourse lining was conducted. The
study is made on the basis of cropping pattern and salinity to evaluate
the system. This study employed an index-based approach of using
Geographic information system with field data. The satellite images
of different years were use to examine the effective area. Several
combinations of the ratio of signals received in different spectral
bands were used for development of this index. Near Infrared and
Thermal IR spectral bands proved to be most effective as this
combination helped easy detection of salt affected area and cropping
pattern of the study area. Result showed that 9.97% area under
salinity in 1992, 9.17% in 2000 and it left 2.29% in year 2005.
Similarly in 1992, 45% area is under vegetation it improves to 56%
and 65% in 2000 and 2005 respectively. On the basis of these results
evaluation is done 30% performance is increase after the watercourse
improvement.
Abstract: The problem of updating damped gyroscopic systems using measured modal data can be mathematically formulated as following two problems. Problem I: Given Ma ∈ Rn×n, Λ = diag{λ1, ··· , λp} ∈ Cp×p, X = [x1, ··· , xp] ∈ Cn×p, where p
Abstract: The current study describes a multi-objective optimization technique for positioning of houses in a residential neighborhood. The main task is the placement of residential houses in a favorable configuration satisfying a number of objectives. Solving the house layout problem is a challenging task. It requires an iterative approach to satisfy design requirements (e.g. energy efficiency, skyview, daylight, roads network, visual privacy, and clear access to favorite views). These design requirements vary from one project to another based on location and client preferences. In the Gulf region, the most important socio-cultural factor is the visual privacy in indoor space. Hence, most of the residential houses in this region are surrounded by high fences to provide privacy, which has a direct impact on other requirements (e.g. daylight and direction to favorite views). This investigation introduces a novel technique to optimally locate and orient residential buildings to satisfy a set of design requirements. The developed technique explores the search space for possible solutions. This study considers two dimensional house planning problems. However, it can be extended to solve three dimensional cases.
Abstract: Finger spelling is an art of communicating by signs
made with fingers, and has been introduced into sign language to serve
as a bridge between the sign language and the verbal language.
Previous approaches to finger spelling recognition are classified into
two categories: glove-based and vision-based approaches. The
glove-based approach is simpler and more accurate recognizing work
of hand posture than vision-based, yet the interfaces require the user to
wear a cumbersome and carry a load of cables that connected the
device to a computer. In contrast, the vision-based approaches provide
an attractive alternative to the cumbersome interface, and promise
more natural and unobtrusive human-computer interaction. The
vision-based approaches generally consist of two steps: hand
extraction and recognition, and two steps are processed independently.
This paper proposes real-time vision-based Korean finger spelling
recognition system by integrating hand extraction into recognition.
First, we tentatively detect a hand region using CAMShift algorithm.
Then fill factor and aspect ratio estimated by width and height
estimated by CAMShift are used to choose candidate from database,
which can reduce the number of matching in recognition step. To
recognize the finger spelling, we use DTW(dynamic time warping)
based on modified chain codes, to be robust to scale and orientation
variations. In this procedure, since accurate hand regions, without
holes and noises, should be extracted to improve the precision, we use
graph cuts algorithm that globally minimize the energy function
elegantly expressed by Markov random fields (MRFs). In the
experiments, the computational times are less than 130ms, and the
times are not related to the number of templates of finger spellings in
database, as candidate templates are selected in extraction step.
Abstract: Localization is one of the critical issues in the field of
robot navigation. With an accurate estimate of the robot pose, robots will be capable of navigating in the environment autonomously and efficiently. In this paper, a hybrid Distributed Vision System (DVS)
for robot localization is presented. The presented approach integrates
odometry data from robot and images captured from overhead cameras
installed in the environment to help reduce possibilities of fail
localization due to effects of illumination, encoder accumulated errors,
and low quality range data. An odometry-based motion model is applied to predict robot poses, and robot images captured by overhead
cameras are then used to update pose estimates with HSV histogram-based measurement model. Experiment results show the
presented approach could localize robots in a global world coordinate system with localization errors within 100mm.
Abstract: A new stochastic algorithm called Probabilistic Global Search Johor (PGSJ) has recently been established for global optimization of nonconvex real valued problems on finite dimensional Euclidean space. In this paper we present convergence guarantee for this algorithm in probabilistic sense without imposing any more condition. Then, we jointly utilize this algorithm along with control
parameterization technique for the solution of constrained optimal control problem. The numerical simulations are also included to illustrate the efficiency and effectiveness of the PGSJ algorithm in the solution of control problems.
Abstract: The control of sprayer boom undesired vibrations pose a great challenge to investigators due to various disturbances and conditions. Sprayer boom movements lead to reduce of spread efficiency and crop yield. This paper describes the design of a novel control method for an active suspension system applying proportional-integral-derivative (PID) controller with an active force control (AFC) scheme integration of an iterative learning algorithm employed to a sprayer boom. The iterative learning as an intelligent method is principally used as a method to calculate the best value of the estimated inertia of the sprayer boom needed for the AFC loop. Results show that the proposed AFC-based scheme performs much better than the standard PID control technique. Also, this shows that the system is more robust and accurate.
Abstract: Transportation is of great importance in the current
life of human beings. The transportation system plays many roles,
from economical development to after-catastrophe aids such as
rescue operation in the first hours and days after an earthquake. In
after earthquakes response phase, transportation system acts as a
basis for ground operations including rescue and relief operation,
food providing for victims and etc. It is obvious that partial or
complete obstruction of this system results in the stop of these
operations. Bridges are one of the most important elements of
transportation network. Failure of a bridge, in the most optimistic
case, cuts the relation between two regions and in more developed
countries, cuts the relation of numerous regions. In this paper, to
evaluate the vulnerability and estimate the damage level of Tehran
bridges, HAZUS method, developed by Federal Emergency
Management Agency (FEMA) with the aid of National Institute of
Building Science (NIBS), is used for the first time in Iran. In this
method, to evaluate the collapse probability, fragility curves are
used. Iran is located on seismic belt and thus, it is vulnerable to
earthquakes. Thus, the study of the probability of bridge collapses, as
an important part of transportation system, during earthquakes is of
great importance. The purpose of this study is to provide fragility
curves for Gisha Bridge, one of the longest steel bridges in Tehran,
as an important lifeline element. Besides, the damage probability for
this bridge during a specific earthquake, introduced as scenario
earthquakes, is calculated. The fragility curves show that for the
considered scenario, the probability of occurrence of complete
collapse for the bridge is 8.6%.
Abstract: In this paper, periodic force operation of a wastewater treatment process has been studied for the improved process performance. A previously developed dynamic model for the process is used to conduct the performance analysis. The static version of the model was utilized first to determine the optimal productivity conditions for the process. Then, feed flow rate in terms of dilution rate i.e. (D) is transformed into sinusoidal function. Nonlinear model predictive control algorithm is utilized to regulate the amplitude and period of the sinusoidal function. The parameters of the feed cyclic functions are determined which resulted in improved productivity than the optimal productivity under steady state conditions. The improvement in productivity is found to be marginal and is satisfactory in substrate conversion compared to that of the optimal condition and to the steady state condition, which corresponds to the average value of the periodic function. Successful results were also obtained in the presence of modeling errors and external disturbances.
Abstract: The modified Arcan fixture was used in order to
investigate the mixed mode fracture properties of high strength steel
butt weld through experimental and numerical analysis. The fixture
consisted of a central section with "butterfly-shaped" specimen that
had central crack. The specimens were under pure mode I (opening),
pure mode II (shearing) and all in plane mixed mode loading angles
starting from 0 to 90 degrees. The geometric calibration factors were
calculated with the aid of finite element analysis for various loading
mode and different crack length (0.45≤ a/w ≤0.55) and the critical
fracture loads obtained experimentally. The critical fracture
toughness (KIC & KIIC) estimated with experimental and numerical
analysis under mixed mode loading conditions.
Abstract: This paper focuses on a technique for identifying the geological boundary of the ground strata in front of a tunnel excavation site using the first order adjoint method based on the optimal control theory. The geological boundary is defined as the boundary which is different layers of elastic modulus. At tunnel excavations, it is important to presume the ground situation ahead of the cutting face beforehand. Excavating into weak strata or fault fracture zones may cause extension of the construction work and human suffering. A theory for determining the geological boundary of the ground in a numerical manner is investigated, employing excavating blasts and its vibration waves as the observation references. According to the optimal control theory, the performance function described by the square sum of the residuals between computed and observed velocities is minimized. The boundary layer is determined by minimizing the performance function. The elastic analysis governed by the Navier equation is carried out, assuming the ground as an elastic body with linear viscous damping. To identify the boundary, the gradient of the performance function with respect to the geological boundary can be calculated using the adjoint equation. The weighed gradient method is effectively applied to the minimization algorithm. To solve the governing and adjoint equations, the Galerkin finite element method and the average acceleration method are employed for the spatial and temporal discretizations, respectively. Based on the method presented in this paper, the different boundary of three strata can be identified. For the numerical studies, the Suemune tunnel excavation site is employed. At first, the blasting force is identified in order to perform the accuracy improvement of analysis. We identify the geological boundary after the estimation of blasting force. With this identification procedure, the numerical analysis results which almost correspond with the observation data were provided.
Abstract: This paper considers a multi criteria cell formation
problem in Cellular Manufacturing System (CMS). Minimizing the
number of voids and exceptional elements in cells simultaneously are
two proposed objective functions. This problem is an Np-hard
problem according to the literature, and therefore, we can-t find the
optimal solution by an exact method. In this paper we developed two
ant algorithms, Ant Colony Optimization (ACO) and Max-Min Ant
System (MMAS), based on Data Envelopment Analysis (DEA). Both
of them try to find the efficient solutions based on efficiency concept
in DEA. Each artificial ant is considered as a Decision Making Unit
(DMU). For each DMU we considered two inputs, the values of
objective functions, and one output, the value of one for all of them.
In order to evaluate performance of proposed methods we provided
an experimental design with some empirical problem in three
different sizes, small, medium and large. We defined three different
criteria that show which algorithm has the best performance.
Abstract: Breast cancer detection techniques have been reported
to aid radiologists in analyzing mammograms. We note that most
techniques are performed on uncompressed digital mammograms.
Mammogram images are huge in size necessitating the use of
compression to reduce storage/transmission requirements. In this
paper, we present an algorithm for the detection of
microcalcifications in the JPEG2000 domain. The algorithm is based
on the statistical properties of the wavelet transform that the
JPEG2000 coder employs. Simulation results were carried out at
different compression ratios. The sensitivity of this algorithm ranges
from 92% with a false positive rate of 4.7 down to 66% with a false
positive rate of 2.1 using lossless compression and lossy compression
at a compression ratio of 100:1, respectively.
Abstract: A. niger XP isolated from Vietnam produces very low amount of acidic phytase with optimal pH at 2.5 and 5.5. The phytase production of this strain was successfully improved through gene cloning and expression. A 1.4 - kb DNA fragment containing the coding region of the phyA gene was amplified by PCR and inserted into the expression vector pPICZαA with a signal peptide α- factor, under the control of AOX1 promoter. The recombined plasmid was transformed into the host strain P. pastoris KM71H and X33 by electroporation. Both host strains could efficiently express and secret phytase. The multicopy strains were screened for over expression of phytase. All the selected multicopy strains of P. pastoris X33 were examined for phytase activity, the maximum phytase yield of 1329 IU/ml was obtained after 4 days of incubation in medium BMM. The recombinant protein with MW of 97.4 KW showed to be the only one protein secreted in the culture broth. Multicopy transformant P. pastoris X33 supposed to be potential candidate for producing the commercial preparation of phytase.