Abstract: An experimental study with four different types of bed
conditions was carried out to understand the effect of roughness in
open channel flow at two different Reynolds numbers. The bed
conditions include a smooth surface and three different roughness
conditions, which were generated using sand grains with a median
diameter of 2.46 mm. The three rough conditions include a surface
with distributed roughness, a surface with continuously distributed
roughness and a sand bed with a permeable interface. A commercial
two-component fibre-optic LDA system was used to conduct the
velocity measurements. The variables of interest include the mean
velocity, turbulence intensity, correlation between the streamwise and
the wall normal turbulence, Reynolds shear stress and velocity triple
products. Quadrant decomposition was used to extract the magnitude
of the Reynolds shear stress of the turbulent bursting events. The
effect of roughness was evident throughout the flow depth. The
results show that distributed roughness has the greatest roughness
effect followed by the sand bed and the continuous roughness.
Compared to the smooth bed, the streamwise turbulence intensity
reduces but the vertical turbulence intensity increases at a location
very close to the bed due to the introduction of roughness. Although
the same sand grain is used to create the three different rough bed
conditions, the difference in the turbulence intensity is an indication
that the specific geometry of the roughness has an influence on
turbulence structure.
Abstract: Construction industry plays a vital role in the
economy of the world. However, due to high uncertainty and
variability in the industry, its performance is not as efficient in terms
of quality, lead times, productivity and costs as of other industries.
Moreover, there are continuous conflicts among the different actors
in the construction supply chains in terms of profit sharing. Previous
studies suggested partnership as an important approach to promote
cooperation among the different actors in the construction supply
chains and thereby it improves the overall performance. Construction
practitioners tried to focus on partnership which can enhance the
performance of construction supply chains but they are not fully
aware of different approaches and techniques for improving
partnership. In this research, a systematic review on partnership in
relation to construction supply chains is carried out to understand
different elements influencing the partnership. The research
development of this domain is analyzed by reviewing selected
articles published from 1996 to 2015. Based on the papers, three
major elements influencing partnership in construction supply chains
are identified: ‘Lean approach’, ‘Relationship building’ and ‘E-commerce
applications’. This study analyses the contributions in the
areas within each element and provides suggestions for future
developments of partnership in construction supply chains.
Abstract: Financial inclusion has become a crucially important
factor in debates on economic inequality posing challenges to the
financial systems of countries around the world. Nowadays
governments and banks are concerned about creating products that
allow access to wide sectors of the population. The creation of
banking products by the financial sector for people with low incomes
tends to lead to improvements in the quality of life of vulnerable parts
of the population. In countries with notable social and economic
inequalities, financial inclusion is a key aspect for equitable
economic growth. This study is based on the case of Colombia, which is a country
with a strong record of economic growth over the past decade.
Nevertheless, corruption, unemployment, and poverty contribute to
uncertainty regarding the country’s future growth prospects. This study wants to explain the situation of financial exclusion and
financial inclusion with respect to the Colombian case. Financial
inclusion is going to be studied from the perspective of social
innovation.
Abstract: The Radio Frequency Identification (RFID) technology
has a diverse base of applications, but it is also prone to security
threats. There are different types of security attacks which limit the
range of the RFID applications. For example, deploying the RFID
networks in insecure environments could make the RFID system
vulnerable to many types of attacks such as spoofing attack, location
traceability attack, physical attack and many more. Therefore, security
is often an important requirement for RFID systems. In this paper,
RFID mutual authentication protocol is implemented based on mobile
agent technology and timestamp, which are used to provide strong
authentication and integrity assurances to both the RFID readers and
their corresponding RFID tags. The integration of mobile agent
technology and timestamp provides promising results towards
achieving this goal and towards reducing the security threats in RFID
systems.
Abstract: This paper describes a subarray based low
computational design method of multiuser massive multiple
input multiple output (MIMO) system. In our previous works, use of
large array is assumed only in transmitter, but this study considers
the case both of transmitter and receiver sides are equipped with
large array antennas. For this aim, receive arrays are also divided
into several subarrays, and the former proposed method is modified
for the synthesis of a large array from subarrays in both ends.
Through computer simulations, it is verified that the performance
of the proposed method is degraded compared with the original
approach, but it can achieve the improvement in the aspect of
complexity, namely, significant reduction of the computational load
to the practical level.
Abstract: Mineral oil is commonly used for high voltage
transformer insulation. The insulation quality of mineral oil is
affecting the operation process of high voltage transformer. There are
many contaminations which could decrease the insulation quality of
mineral oil. One of them is water. This research talks about the effect
of water content on dielectric properties, physic properties, and
partial discharge pattern on mineral oil. Samples were varied with 10
varieties of water content value. And then all samples would be tested
to measure the dielectric properties, physic properties, and partial
discharge pattern. The result of this research showed that an
increment of water content value would decrease the insulation
quality of mineral oil.
Abstract: Recently, numerous documents including large
volumes of unstructured data and text have been created because of the
rapid increase in the use of social media and the Internet. Usually,
these documents are categorized for the convenience of users. Because
the accuracy of manual categorization is not guaranteed, and such
categorization requires a large amount of time and incurs huge costs.
Many studies on automatic categorization have been conducted to help
mitigate the limitations of manual categorization. Unfortunately, most
of these methods cannot be applied to categorize complex documents
with multiple topics because they work on the assumption that
individual documents can be categorized into single categories only.
Therefore, to overcome this limitation, some studies have attempted to
categorize each document into multiple categories. However, the
learning process employed in these studies involves training using a
multi-categorized document set. These methods therefore cannot be
applied to the multi-categorization of most documents unless
multi-categorized training sets using traditional multi-categorization
algorithms are provided. To overcome this limitation, in this study, we
review our novel methodology for extending the category of a
single-categorized document to multiple categorizes, and then
introduce a survey-based verification scenario for estimating the
accuracy of our automatic categorization methodology.
Abstract: For schools to be desirable places in which to work, it
is necessary for principals to recognise their teachers’ emotions, and
be sensitive to their needs. This necessitates that principals are
capable to correctly identify their emotionally intelligent behaviours
(EIBs) they need to use in order to be successful leaders. They also
need to have knowledge of their emotional intelligence and be able to
identify the factors and situations that evoke emotion at an
interpersonal level. If a principal is able to do this, then the control
and understanding of emotions and behaviours of oneself and others
could improve vastly. This study focuses on the interpersonal EIBS
of principals affecting the job satisfaction of teachers. The correlation
coefficients in this quantitative study strongly indicate that there is a
statistical significance between the respondents’ level of job
satisfaction, the rating of their principals’ EIBs and how they believe
their principals’ EIBs will affect their sense of job satisfaction. It can
be concluded from the data obtained in this study that there is a
significant correlation between the sense of job satisfaction of
teachers and their principals’ interpersonal EIBs. This means that the
more satisfied a teacher is at school, the more appropriate and
meaningful a principal’s EIBs will be. Conversely, the more
dissatisfied a teacher is at school the less appropriate and less
meaningful a principal’s interpersonal EIBs will be. This implies that
the leaders’ EIBs can be construed as one of the major factors
affecting the job satisfaction of employees.
Abstract: The influence of Islam on arts can be found primarily
in calligraphy, arabesque designs and architecture. Also, geometric
designs were used quite extensively. Muslim craftsmen produced
stunning designs based on simple geometric principles and traditional
motifs which were used to decorate many surfaces. The idea of
interlacing simple rectilinear lines to form the patterns impressed
Arabs. Nomads of Persia, Turks and Mongols were equally
impressed with the designs so they begin to use them in their homes
in carpet weaving. Islamic designs, motifs and colours which were
used became common place and served to influence people’s tastes.
Modern life style and contemporary products have changed the style
of people’s daily lives, however, people still long for the nomadic
way of life. This is clearly reflected in people’s homes. In a great
many Muslim homes, Islamic decorative motifs can be seen along
with traditional ‘Bedouin’ style furnishing, especially in homes of the
Arabian Peninsula.
Abstract: The knitted fabric suffers a deformation in its
dimensions due to stretching and tension factors, transverse and
longitudinal respectively, during the process in rectilinear knitting
machines so it performs a dry relaxation shrinkage procedure and
thermal action of prefixed to obtain stable conditions in the knitting.
This paper presents a dry relaxation shrinkage prediction of Bordeaux
fiber using a feed forward neural network and linear regression
models. Six operational alternatives of shrinkage were predicted. A
comparison of the results was performed finding neural network
models with higher levels of explanation of the variability and
prediction. The presence of different reposes is included. The models
were obtained through a neural toolbox of Matlab and Minitab
software with real data in a knitting company of Southern
Guanajuato. The results allow predicting dry relaxation shrinkage of
each alternative operation.
Abstract: An analytical 4-DOF nonlinear model of a de Laval
rotor-stator system based on Energy Principles has been used
theoretically and experimentally to investigate fault symptoms in a
rotating system. The faults, namely rotor-stator-rub, crack and
unbalance are modeled as excitations on the rotor shaft. Mayes
steering function is used to simulate the breathing behaviour of the
crack. The fault analysis technique is based on waveform signal,
orbits and Fast Fourier Transform (FFT) derived from simulated and
real measured signals. Simulated and experimental results manifest
considerable mutual resemblance of elliptic-shaped orbits and FFT
for a same range of test data.
Abstract: Nonlinear evolution of broadband ultrasonic pulses
passed through the rock specimens is studied using the apparatus
“GEOSCAN-02M”. Ultrasonic pulses are excited by the pulses of Qswitched
Nd:YAG laser with the time duration of 10 ns and with the
energy of 260 mJ. This energy can be reduced to 20 mJ by some light
filters. The laser beam radius did not exceed 5 mm. As a result of the
absorption of the laser pulse in the special material – the optoacoustic
generator–the pulses of longitudinal ultrasonic waves are excited with
the time duration of 100 ns and with the maximum pressure
amplitude of 10 MPa. The immersion technique is used to measure
the parameters of these ultrasonic pulses passed through a specimen,
the immersion liquid is distilled water. The reference pulse passed
through the cell with water has the compression and the rarefaction
phases. The amplitude of the rarefaction phase is five times lower
than that of the compression phase. The spectral range of the
reference pulse reaches 10 MHz. The cubic-shaped specimens of the
Karelian gabbro are studied with the rib length 3 cm. The ultimate
strength of the specimens by the uniaxial compression is (300±10)
MPa. As the reference pulse passes through the area of the specimen
without cracks the compression phase decreases and the rarefaction
one increases due to diffraction and scattering of ultrasound, so the
ratio of these phases becomes 2.3:1. After preloading some horizontal
cracks appear in the specimens. Their location is found by one-sided
scanning of the specimen using the backward mode detection of the
ultrasonic pulses reflected from the structure defects. Using the
computer processing of these signals the images are obtained of the
cross-sections of the specimens with cracks. By the increase of the
reference pulse amplitude from 0.1 MPa to 5 MPa the nonlinear
transformation of the ultrasonic pulse passed through the specimen
with horizontal cracks results in the decrease by 2.5 times of the
amplitude of the rarefaction phase and in the increase of its duration
by 2.1 times. By the increase of the reference pulse amplitude from 5
MPa to 10 MPa the time splitting of the phases is observed for the
bipolar pulse passed through the specimen. The compression and
rarefaction phases propagate with different velocities. These features
of the powerful broadband ultrasonic pulses passed through the rock
specimens can be described by the hysteresis model of Preisach-
Mayergoyz and can be used for the location of cracks in the optically
opaque materials.
Abstract: Si-Ge solid solutions (bulk poly- and mono-crystalline
samples, thin films) are characterized by high perspectives for
application in semiconductor devices, in particular, optoelectronics
and microelectronics. From this point of view, complex studying of
structural state of the defects and structural-sensitive physical
properties of Si-Ge solid solutions depending on the contents of Si
and Ge components is very important. Present work deals with the
investigations of microstructure, microhardness, internal friction and
shear modulus of Si1-xGex(x≤0,02) bulk monocrystals conducted at
room temperature. Si-Ge bulk crystals were obtained by Czochralski
method in [111] crystallographic direction. Investigated
monocrystalline Si-Ge samples are characterized by p-type
conductivity and carriers’ concentration 5.1014-1.1015cm-3.
Microhardness was studied on Dynamic Ultra Micro hardness Tester
DUH-201S with Berkovich indenter. Investigate samples are characterized with 0,5x0,5x(10-15)mm3
sizes, oriented along [111] direction at torsion oscillations ≈1Hz,
multistage changing of internal friction and shear modulus has been
revealed in an interval of strain amplitude of 10-5-5.10-3. Critical
values of strain amplitude have been determined at which hysteretic
changes of inelastic characteristics and microplasticity are observed. The critical strain amplitude and elasticity limit values are also
determined. Dynamic mechanical characteristics decreasing trend is
shown with increasing Ge content in Si-Ge solid solutions. Observed
changes are discussed from the point of view of interaction of various
dislocations with point defects and their complexes in a real structure
of Si-Ge solid solutions.
Abstract: Research has shown that techno-entrepreneurship is
economically significant. Therefore, it is suggested that teaching
techno-entrepreneurship may be important because such programmes
would prepare current and future generations of learners to recognise
and act on high-technology opportunities. Education in technoentrepreneurship
may increase the knowledge of how to start one’s
own enterprise and recognise the technological opportunities for
commercialisation to improve decision-making about starting a new
venture; also it influence decisions about capturing the business
opportunities and turning them into successful ventures. Universities
can play a main role in connecting and networking technoentrepreneurship
students towards a cooperative attitude with real
business practice and industry knowledge. To investigate and answer
whether education for techno-entrepreneurs really helps, this paper
choses a comparison of literature reviews as its method of research.
After reviewing literature related to the impact of technoentrepreneurship
education on self-employment 6 studies which had
similar aim and objective to this paper were. These particular papers
were selected based on a keywords search and as their aim,
objectives, and gaps were close to the current research. In addition,
they were all based on the influence of techno-entrepreneurship
education in self-employment and intention of students to start new
ventures. The findings showed that teaching techno-entrepreneurship
education may have an influence on students’ intention and their
future self-employment, but which courses should be covered and the
duration of programmes, needs further investigation.
Abstract: The need to merge software artifacts seems inherent
to modern software development. Distribution of development over
several teams and breaking tasks into smaller, more manageable
pieces are an effective means to deal with the kind of complexity. In
each case, the separately developed artifacts need to be assembled as
efficiently as possible into a consistent whole in which the parts still
function as described. In addition, earlier changes are introduced into
the life cycle and easier is their management by designers.
Interaction-based specifications such as UML sequence diagrams
have been found effective in this regard. As a result, sequence
diagrams can be used not only for capturing system behaviors but
also for merging changes in order to create a new version. The
objective of this paper is to suggest a new approach to deal with the
problem of software merging at the level of sequence diagrams by
using the concept of dependence analysis that captures, formally, all
mapping, and differences between elements of sequence diagrams
and serves as a key concept to create a new version of sequence
diagram.
Abstract: Urinary Tract Infections are considered as one of the
most common bacterial infections with an estimated annual global
incidence of 150 million. Antimicrobial drug resistance is one of the
major threats due to wide spread usage of uncontrolled antibiotics. In
this study, a total number of 9149 urine samples were collected from
R.H Patiala and processed in the Department of Microbiology G. M.
C Patiala (January 2013 to December 2013). Urine samples were
inoculated on MacConkey’s and blood agar plates and incubated at
370C for 24 hrs. The organisms were identified by colony characters,
Gram’s staining, and biochemical reactions. Antimicrobial
susceptibility of the isolates was determined against various
antimicrobial agents (Hi – Media Mumbai India) by Kirby Bauer
DISK diffusion method on Muller Hinton agar plates. Maximum patients were in the age group of 21-30 yrs followed by
31-40 yrs. Males (34%) are less prone to urinary tract infections than
females (66%). Culture was positive in 25% of the samples.
Escherichia coli was the most common isolate 60.3% followed by
Klebsiella pneumoniae 13.5%, Proteus spp. 9% and Staphylococcus
aureus 7.6%. Most of the urinary isolates were sensitive to,
carbepenems, Aztreonam, Amikacin, and Piperacillin + Tazobactum.
All the isolates showed a good sensitivity towards Nitrofurantoin
(82%). ESBL production was found to be 70.6% in Escherichia coli
and 29.4% in Klebsiella pneumonia. Susceptibility of ESBL
producers to Imipenem, Nitrofurantoin and Amikacin were found to
be 100%, 76%, and 75% respectively. Uropathogens are increasingly
showing resistance to many antibiotics making empiric management
of outpatient UTIs challenging. Ampicillin, Cotrimoxazole and
Ciprofloxacin should not be used in empiric treatment. Nitrofurantoin
could be used in lower urinary tract infection. Knowledge of
uropathogens and their antimicrobial susceptibility pattern in a
geographical region will help in appropriate and judicious antibiotic
usage in a health care setup.
Abstract: In this paper, we present a comparative study of three
methods of 2D face recognition system such as: Iso-Geodesic Curves
(IGC), Geodesic Distance (GD) and Geodesic-Intensity Histogram
(GIH). These approaches are based on computing of geodesic
distance between points of facial surface and between facial curves.
In this study we represented the image at gray level as a 2D surface in
a 3D space, with the third coordinate proportional to the intensity
values of pixels. In the classifying step, we use: Neural Networks
(NN), K-Nearest Neighbor (KNN) and Support Vector Machines
(SVM). The images used in our experiments are from two wellknown
databases of face images ORL and YaleB. ORL data base was
used to evaluate the performance of methods under conditions where
the pose and sample size are varied, and the database YaleB was used
to examine the performance of the systems when the facial
expressions and lighting are varied.
Abstract: Heart is the most important part in the body of living
organisms. It affects and is affected by any factor in the body.
Therefore, it is a good detector for all conditions in the body. Heart
signal is a non-stationary signal; thus, it is utmost important to study
the variability of heart signal. The Heart Rate Variability (HRV) has
attracted considerable attention in psychology, medicine and has
become important dependent measure in psychophysiology and
behavioral medicine. The standards of measurements, physiological
interpretation and clinical use for HRV that are most often used were
described in many researcher papers, however, remain complex
issues are fraught with pitfalls. This paper presents one of the nonlinear
techniques to analyze HRV. It discusses many points like, what
Poincaré plot is and how Poincaré plot works; also, Poincaré plot's
merits especially in HRV. Besides, it discusses the limitation of
Poincaré cause of standard deviation SD1, SD2 and how to overcome
this limitation by using complex correlation measure (CCM). The
CCM is most sensitive to changes in temporal structure of the
Poincaré plot as compared toSD1 and SD2.
Abstract: This research was conducted in an automotive company in Indonesia to overcome the problem of high logistics cost. The problem causes high of additional truck delivery. From the breakdown of the problem, chosen one route, which has the highest gap value, namely for RE-04. Research methodology will be started from calculating the ideal condition, making simulation, calculating the ideal logistic cost, and proposing an improvement. From the calculation of the ideal condition, box arrangement was done on the truck has efficiency with three trucks delivery per day. Route simulation making uses Tecnomatix Plant Simulation software as a visualization for the company about how the system is occurred on route RE-04 in ideal condition. The last step is proposing improvements on the area of route RE-04. The route arrangement is done by Saving Method and sequence of each supplier with the Nearest Neighbor. The results of the proposed improvements are three new route groups, where was expected to decrease logistics cost and increase the average of the truck efficiency per day.
Abstract: Ocean current is always available around the
surrounding of SHELL Sabah Water Platform and data are collected
every 10 minutes, 24 hours a day, for a period of 365 days. Due to
low current speed, conventional hydrokinetic power generation is not
feasible, thus leading to the study of low current enabled vortex
induced vibration power generation application. In this case, the
design of a vortex induced vibration application is studied to obtain
an optimum design for the VIV oscillator. Power output is then
determined to study the feasibility of the VIV application in low
current condition.