Abstract: The utilize of renewable energy sources becomes
more crucial and fascinatingly, wider application of renewable
energy devices at domestic, commercial and industrial levels is not
only affect to stronger awareness but also significantly installed
capacities. Moreover, biomass principally is in form of woods and
converts to be energy for using by humans for a long time.
Gasification is a process of conversion of solid carbonaceous fuel
into combustible gas by partial combustion. Many gasified models
have various operating conditions because the parameters kept in
each model are differentiated. This study applied the experimental
data including three inputs variables including biomass consumption;
temperature at combustion zone and ash discharge rate and gas flow
rate as only one output variable. In this paper, response surface
methods were applied for identification of the gasified system
equation suitable for experimental data. The result showed that linear
model gave superlative results.
Abstract: Experiments have been carried out at sub-critical
Reynolds number to investigate free-to-roll motions induced by
forebody and/or wings complex flow on a 30° swept back nonslender
wings-slender body-model for static and dynamic (pitch-up)
cases. For the dynamic (pitch-up) case it has been observed that roll
amplitude decreases and lag increases with increase in pitching
speed. Decrease in roll amplitude with increase in pitch rate is
attributed to low disturbing rolling moment due to weaker interaction
between forebody and wing flow components. Asymmetric forebody
vortices dominate and control the roll motion of the model in
dynamic case when non-dimensional pitch rate ≥ 1x10-2.
Effectiveness of the active control scheme utilizing rotating nose with
artificial tip perturbation is observed to be low in the angle of attack
region where the complex flow over the wings has contributions from
both forebody and wings.
Abstract: Prickly pear juice has received renewed attention with regard to the effects of processing and preservation on its sensory qualities (colour, taste, flavour, aroma, astringency, visual browning and overall acceptability). Juice was prepared by homogenizing fruit and treating the pulp with pectinase (Aspergillus niger). Juice treatments applied were sugar addition, acidification, heat-treatment, refrigeration, and freezing and thawing. Prickly pear pulp and juice had unique properties (low pH 3.88, soluble solids 3.68 oBrix and high titratable acidity 0.47). Sensory profiling and descriptive analyses revealed that non-treated juice had a bitter taste with high astringency whereas treated prickly pear was significantly sweeter. All treated juices had a good sensory acceptance with values approximating or exceeding 7. Regression analysis of the consumer sensory attributes for non-treated prickly pear juice indicated an overwhelming rejection, while treated prickly pear juice received overall acceptability. Thus, educed favourable sensory responses and may have positive implications for consumer acceptability.
Abstract: Fischer-Tropsch synthesis is one of the most
important catalytic reactions that convert the synthetic gas to light
and heavy hydrocarbons. One of the main issues is selecting the type
of reactor. The slurry bubble reactor is suitable choice for Fischer-
Tropsch synthesis because of its good qualification to transfer heat
and mass, high durability of catalyst, low cost maintenance and
repair. The more common catalysts for Fischer-Tropsch synthesis are
Iron-based and Cobalt-based catalysts, the advantage of these
catalysts on each other depends on which type of hydrocarbons we
desire to produce. In this study, Fischer-Tropsch synthesis is modeled
with Iron and Cobalt catalysts in a slurry bubble reactor considering
mass and momentum balance and the hydrodynamic relations effect
on the reactor behavior. Profiles of reactant conversion and reactant
concentration in gas and liquid phases were determined as the
functions of residence time in the reactor. The effects of temperature,
pressure, liquid velocity, reactor diameter, catalyst diameter, gasliquid
and liquid-solid mass transfer coefficients and kinetic
coefficients on the reactant conversion have been studied. With 5%
increase of liquid velocity (with Iron catalyst), H2 conversions
increase about 6% and CO conversion increase about 4%, With 8%
increase of liquid velocity (with Cobalt catalyst), H2 conversions
increase about 26% and CO conversion increase about 4%. With
20% increase of gas-liquid mass transfer coefficient (with Iron
catalyst), H2 conversions increase about 12% and CO conversion
increase about 10% and with Cobalt catalyst H2 conversions increase
about 10% and CO conversion increase about 6%. Results show that
the process is sensitive to gas-liquid mass transfer coefficient and
optimum condition operation occurs in maximum possible liquid
velocity. This velocity must be more than minimum fluidization
velocity and less than terminal velocity in such a way that avoid
catalysts particles from leaving the fluidized bed.
Abstract: Repetitive control and feedback dithering modulation
are applied to a single-phase voltage source inverter, with an aim to
eliminate harmonics and stabilize the inverter under load variations.
The proposed control and modulation scheme comprise multiple loops
of feedback, which helps improve inverter performance and
robustness. Experimental results show that the designed inverter
exhibits very low distortion at its output with THD of about 0.3%
under different load variations.
Abstract: Intellectual capital measurement is a central aspect of knowledge management. The measurement and the evaluation of intangible assets play a key role in allowing an effective management of these assets as sources of competitiveness. For these reasons, managers and practitioners need conceptual and analytical tools taking into account the unique characteristics and economic significance of Intellectual Capital. Following this lead, we propose an efficiency and productivity analysis of Intellectual Capital, as a determinant factor of the company competitive advantage. The analysis is carried out by means of Data Envelopment Analysis (DEA) and Malmquist Productivity Index (MPI). These techniques identify Bests Practice companies that have accomplished competitive advantage implementing successful strategies of Intellectual Capital management, and offer to inefficient companies development paths by means of benchmarking. The proposed methodology is employed on the Biotechnology industry in the period 2007-2010.
Abstract: The study aimed to evaluated the reproductive performance response to short term oestrus synchronization during the transition period. One hundred and sixty-five indigenous multiparous non-lactating goats were subdivided into the following six treatment groups for oestrus synchronization: NT control Group (N= 30), Fe-21d, FGA vaginal sponge for 21days+eCG at 19thd; FPe- 11d, FGA 11d + PGF2α and eCG at 9th d; FPe-10d, FGA 10d+ PGF2α and eCG at 8th d; FPe-9d, FGA 9d +PGF2α and eCG at 7thd; PFe-5d, PGF2α at d0 + FGA 5d + eCG at 5thd. The goats were natural mated (1 male/6 females). Fecundity rates (n. births /n. females treated x 100) were statistically higher (P < 0.05) in short term FPe-9d (157.9%), FPe- 11d (115.4%), FPe-10d (111.1%) and PFe-5d (107.7%) groups compared to the NT control Group (66.7%).
Abstract: Little attention has been paid to information
transmission between the portfolios of large stocks and small stocks in the Korean stock market. This study investigates the return and volatility transmission mechanisms between large and small stocks in
the Korea Exchange (KRX). This study also explores whether bad news in the large stock market leads to a volatility of the small stock
market that is larger than the good news volatility of the large stock market. By employing the Granger causality test, we found
unidirectional return transmissions from the large stocks to medium
and small stocks. This evidence indicates that pat information about
the large stocks has a better ability to predict the returns of the medium and small stocks in the Korean stock market. Moreover, by using the
asymmetric GARCH-BEKK model, we observed the unidirectional relationship of asymmetric volatility transmission from large stocks to
the medium and small stocks. This finding suggests that volatility in
the medium and small stocks following a negative shock in the large
stocks is larger than that following a positive shock in the large stocks.
Abstract: In today's world where everything is rapidly changing
and information technology is high in development, many features of culture, society, politic and economy has changed. The advent of
information technology and electronic data transmission lead to easy communication and fields like e-learning and e-commerce, are
accessible for everyone easily. One of these technologies is virtual
training. The "quality" of such kind of education systems is critical. 131 questionnaires were prepared and distributed among university
student in Toba University. So the research has followed factors that affect the quality of learning from the perspective of staff, students, professors and this type of university. It is concluded that the important factors in virtual training are the quality of professors, the
quality of staff, and the quality of the university. These mentioned factors were the most prior factors in this education system and
necessary for improving virtual training.
Abstract: This paper presents a new optimization technique based on quantum computing principles to solve a security constrained power system economic dispatch problem (SCED). The proposed technique is a population-based algorithm, which uses some quantum computing elements in coding and evolving groups of potential solutions to reach the optimum following a partially directed random approach. The SCED problem is formulated as a constrained optimization problem in a way that insures a secure-economic system operation. Real Coded Quantum-Inspired Evolution Algorithm (RQIEA) is then applied to solve the constrained optimization formulation. Simulation results of the proposed approach are compared with those reported in literature. The outcome is very encouraging and proves that RQIEA is very applicable for solving security constrained power system economic dispatch problem (SCED).
Abstract: The widely used Total Variation de-noising algorithm can preserve sharp edge, while removing noise. However, since fixed regularization parameter over entire image, small details and textures are often lost in the process. In this paper, we propose a modified Total Variation algorithm to better preserve smaller-scaled features. This is done by allowing an adaptive regularization parameter to control the amount of de-noising in any region of image, according to relative information of local feature scale. Experimental results demonstrate the efficient of the proposed algorithm. Compared with standard Total Variation, our algorithm can better preserve smaller-scaled features and show better performance.
Abstract: In the present work steady inviscid hypersonic flows
are calculated by approximate Method. Maslens' inverse method is the chosen approximate method. For the inverse problem, parabolic
shock shape is chosen for the two-dimensional flow, and the body shape and flow field are calculated using Maslen's method. For the axisymmetric inverse problem paraboloidal shock is chosen and the
surface distribution of pressure is obtained.
Abstract: The distribution, enrichment, accumulation, and potential ecological risk of copper (Cu) in the surface sediments of northern Kaohsiung Harbor, Taiwan were investigated. Sediment samples from 12 locations of northern Kaohsiung Harbor were collected and characterized for Cu, aluminum, water content, organic matter, total nitrogen, total phosphorous, total grease and grain size. Results showed that the Cu concentrations varied from 6.9–244 mg/kg with an average of 109±66 mg/kg. The spatial distribution of Cu reveals that the Cu concentration is relatively high in the river mouth region, and gradually diminishes toward the harbor entrance region. This indicates that upstream industrial and municipal wastewater discharges along the river bank are major sources of Cu pollution. Results from the enrichment factor and geo-accumulation index analyses imply that the sediments collected from the river mouth can be characterized between moderate and moderately severe degree enrichment and between none to medium and moderate accumulation of Cu, respectively. However, results of potential ecological risk index indicate that the sediment has low ecological potential risk.
Abstract: A hybrid Photovoltaic/Thermal (PV/T) solar system integrates photovoltaic and solar thermal technologies into one single solar energy device, with dual generation of electricity and heat energy. The aim of the present study is to evaluate the potential for introduction of the PV/T technology into Northern China. For this purpose, outdoor experiments were conducted on a prototype of a PV/T water-heating system. The annual thermal and electrical performances were investigated under the climatic conditions of Beijing. An economic analysis of the system was then carried out, followed by a sensitivity study. The analysis revealed that the hybrid system is not economically attractive with the current market and energy prices. However, considering the continuous commitment of the Chinese government towards policy development in the renewable energy sector, and technological improvements like the increasing cost-effectiveness of PV cells, PV/Thermal technology may become economically viable in the near future.
Abstract: Turkey has 72 % of total world boron reserves on the
basis of B2O3.Borates that is a refined form of boron minerals have a
wide range of applications. Zinc borates can be used as multifunctional
synergistic additives. The most important properties are
low solubility in water and high dehydration temperature. Zinc
borates dehydrate above 290°C and anhydrous zinc borate has
thermal resistance about 400°C. Zinc borates can be synthesized
using several methods such as hydrothermal and solid-state
processes. In this study, the solid-state method was applied between
500 and 800°C using the starting materials of ZnO and H3BO3 with
1:4 mole ratio. The reaction time was determined as 4 hours after
some preliminary experiments. After the synthesis, the crystal
structure and the morphology of the products were examined by XRay
Diffraction (XRD), Fourier Transform Infrared Spectroscopy
(FT-IR) and Raman Spectrometer. As a result the form of ZnB4O7
was synthesized with the highest crystal score at 800°C.
Abstract: This paper introduces a framework based on the collaboration of multi agent and hyper-heuristics to find a solution of the real single machine production problem. There are many techniques used to solve this problem. Each of it has its own advantages and disadvantages. By the collaboration of multi agent system and hyper-heuristics, we can get more optimal solution. The hyper-heuristics approach operates on a search space of heuristics rather than directly on a search space of solutions. The proposed framework consists of some agents, i.e. problem agent, trainer agent, algorithm agent (GPHH, GAHH, and SAHH), optimizer agent, and solver agent. Some low level heuristics used in this paper are MRT, SPT, LPT, EDD, LDD, and MON
Abstract: Roundabout work on the principle of circulation and
entry flows, where the maximum entry flow rates depend largely on
circulating flow bearing in mind that entry flows must give away to
circulating flows. Where an existing roundabout has a road hump
installed at the entry arm, it can be hypothesized that the kinematics
of vehicles may prevent the entry arm from achieving optimum
performance. Road humps are traffic calming devices placed across
road width solely as speed reduction mechanism. They are the
preferred traffic calming option in Malaysia and often used on single
and dual carriageway local routes. The speed limit on local routes is
30mph (50 km/hr). Road humps in their various forms achieved the
biggest mean speed reduction (based on a mean speed before traffic
calming of 30mph) of up to 10mph or 16 km/hr according to the UK
Department of Transport. The underlying aim of reduced speed
should be to achieve a 'safe' distribution of speeds which reflects the
function of the road and the impacts on the local community.
Constraining safe distribution of speeds may lead to poor drivers
timing and delayed reflex reaction that can probably cause accident.
Previous studies on road hump impact have focused mainly on speed
reduction, traffic volume, noise and vibrations, discomfort and delay
from the use of road humps. The paper is aimed at optimal entry and
circulating flow induced by road humps. Results show that
roundabout entry and circulating flow perform better in
circumstances where there is no road hump at entrance.
Abstract: Carbon nanotubes (CNTs) with their high mechanical,
electrical, thermal and chemical properties are regarded as promising
materials for many different potential applications. Having unique
properties they can be used in a wide range of fields such as
electronic devices, electrodes, drug delivery systems, hydrogen
storage, textile etc. Catalytic chemical vapor deposition (CCVD) is a
common method for CNT production especially for mass production.
Catalysts impregnated on a suitable substrate are important for
production with chemical vapor deposition (CVD) method. Iron
catalyst and MgO substrate is one of most common catalyst-substrate
combination used for CNT. In this study, CNTs were produced by
CCVD of acetylene (C2H2) on magnesium oxide (MgO) powder
substrate impregnated by iron nitrate (Fe(NO3)3•9H2O) solution. The
CNT synthesis conditions were as follows: at synthesis temperatures
of 500 and 800°C multiwall and single wall CNTs were produced
respectively. Iron (Fe) catalysts were prepared by with Fe:MgO ratio
of 1:100, 5:100 and 10:100. The duration of syntheses were 30 and
60 minutes for all temperatures and catalyst percentages. The
synthesized materials were characterized by thermal gravimetric
analysis (TGA), transmission electron microscopy (TEM) and Raman
spectroscopy.
Abstract: This paper aims to (1) analyze the profiles of
transgressors (detected evaders); (2) examine reason(s) that triggered a
tax audit, causes of tax evasion, audit timeframe and tax penalty
charged; and (3) to assess if tax auditors followed the guidelines as
stated in the 'Tax Audit Framework' when conducting tax audits. In
2011, the Inland Revenue Board Malaysia (IRBM) had audited and
finalized 557 company cases. With official permission, data of all the
557 cases were obtained from the IRBM. Of these, a total of 421 cases
with complete information were analyzed. About 58.1% was small and
medium corporations and from the construction industry (32.8%). The
selection for tax audit was based on risk analysis (66.8%), information
from third party (11.1%), and firm with low profitability or fluctuating
profit pattern (7.8%). The three persistent causes of tax evasion by
firms were over claimed expenses (46.8%), fraudulent reporting of
income (38.5%) and overstating purchases (10.5%). These findings
are consistent with past literature. Results showed that tax auditors
took six to 18 months to close audit cases. More than half of tax
evaders were fined 45% on additional tax raised during audit for the
first offence. The study found tax auditors did follow the guidelines in
the 'Tax Audit Framework' in audit selection, settlement and penalty
imposition.
Abstract: The aim of present experiment was to evaluate the
influence of cultivar to quality parameters of dried potato chips and
sticks produced in microwave-vacuum drier. The potatoes before
drying were blanched in oil and water at 180ºC and at 85ºC
respectively. The moisture content, crispiness, the colour (CIE
L*a*b*), the content of ascorbic acid, total carotenoids and total fat
content of dried potato chips and sticks was determined The highest
ascorbic acid content, high content of carotenoids, low total fat
content, low acrylamide content and good crispiness (low breaking
force) especially for sticks was determined in the samples of Gundega
cultivar.