Abstract: Five vegetables (spinach, lettuce, cabbage, tomato, and onion) were freshly harvested from the Alau Dam and Gongulong agricultural areas for the determination of some organochlorine pesticide residues (o, p-DDE, p,p’-DDD, o,p’-DDD, p,p’-DDT, α-BHC, γ-BHC, metoxichlor, lindane, endosulfan dieldrin, and aldrin.) Soil samples were also collected at different depths for the determination of the above pesticides. Samples collection and preparation were conducted using standard procedures. The concentrations of all the pesticides in the soil and vegetable samples were determined using GC/MS SHIMADZU (GC-17A) equipped with electron capture detector (ECD). The highest concentration was that of p,p’-DDD (132.4±13.45µg/g) which was observed in the leaf of cabbage, while the lowest concentration was that of p,p’-DDT (2.34µg/g) was observed in the root of spinach. Similar trends were observed at the Gongulong agricultural area, with p,p’-DDD having the highest concentration of 153.23µg/g in the leaf of cabbage, while the lowest concentration was that of p,p’-DDT (12.45µg/g) which was observed in the root of spinach. α-BHC, γ-BHC, Methoxychlor, and lindane were detected in all the vegetable samples studied. The concentrations of all the pesticides in the soil samples were observed to be higher at a depth of 21-30cm, while the lowest concentrations were observed at a depth of 0-10cm. The concentrations of all the pesticides in the vegetables and soil samples from the two agricultural sites were observed to be at alarming levels, much higher than the maximum residue limits (MRLs) and acceptable daily intake values (ADIs) .The levels of the pesticides observed in the vegetables and soil samples investigated, are of such a magnitude that calls for special attention and laws to regulate the use and circulation of such chemicals. Routine monitoring of pesticide residues in these study areas is necessary for the prevention, control and reduction of environmental pollution, so as to minimize health risks.
Abstract: Although there are many theories and discussion of leadership, the necessity of having a new leadership paradigm was emphasized. The existing leadership characteristic of instruction and control revealed its limitations. Market competition becomes fierce and economic recession never ends worldwide. Of the leadership theories, servant leadership was introduced recently and is in line with the environmental changes of the organization. Servant leadership is a combination of two words, 'servant' and 'leader' and can be defined as the role of the leader who focuses on doing voluntary work for others with altruistic ethics, makes members, customers, and local communities a priority, and makes a commitment to satisfying their needs. This leadership received attention as one field of leadership in the late 1990s and secured its legitimacy. This study discusses the existing research trends of leadership, the concept, behavior characteristics, and lower dimensions of servant leadership, compares servant leadership with the existing leadership researches and diagnoses if servant leadership is a useful concept for further leadership researches. Finally, this study criticizes the limitations in the existing researches on servant leadership.
Abstract: The technique of inducing micro ecosystem
restoration is one of aquatic ecology engineering methods used to
retrieve the polluted water. Batch scale study, pilot plant study, and
field study were carried out to observe the eutrophication using the
Inducing Ecology Restorative Symbiosis Agent (IERSA) consisting
mainly degraded products by using lactobacillus, saccharomycete,
and phycomycete. The results obtained from the experiments of the
batch scale and pilot plant study allowed us to development the
parameters for the field study. A pond, 5 m to the outlet of a lake,
with an area of 500 m2 and depth of 0.6-1.2 m containing about 500
tons of water was selected as a model. After the treatment with 10
mg IERSA/L water twice a week for 70 days, the micro restoration
mechanisms consisted of three stages (i.e., restoration, impact
maintenance, and ecology recovery experiment after impact). The
COD, TN, TKN, and chlorophyll a were reduced significantly in the
first week. Although the unexpected heavy rain and contaminate
from sewage system might slow the ecology restoration. However,
the self-cleaning function continued and the chlorophyll a reduced
for 50% in one month. In the 4th week, amoeba, paramecium, rotifer,
and red wriggle worm reappeared, and the number of fish flies
appeared up to1000 fish fries/m3. Those results proved that inducing
restorative mechanism can be applied to improve the eutrophication
and to control the growth of algae in the lakes by gaining the selfcleaning
through inducing and competition of microbes. The
situation for growth of fishes also can reach an excellent result due to
the improvement of water quality.
Abstract: The main purpose of this study is to analyze the
relationship of leisure agriculture park visitors on tourist destination
image, environmental perception, travel experiences and revisiting
willingness. This study used questionnaires to Xinshe leisure
agriculture park visitors- targeted convenience sampling manner total
of 636 valid questionnaires. Valid questionnaires by descriptive
statistics, correlation analysis and multiple regression analysis, the
study found that: 1. The agricultural park visitors- correlations exist
between the destination image, perception of the environment, tourism
experience and revisiting willingness. 2."Excellent facilities and
services", "space atmosphere comfortable" and "the spacious paternity
outdoor space" imagery, of visitors- "revisiting willingness predict. 3.
Visitors- in leisure agriculture park "environmental perception" and
"travel experience, future revisiting willingness predict. According to
the analysis of the results, the study not only operate on the
recommendations of the leisure farm owners also provide follow-up
study direction for future researchers.
Abstract: In this paper, a new encoding algorithm of spectral envelope based on NLMS in G.729.1 for VoIP is proposed. In the TDAC part of G.729.1, the spectral envelope and MDCT coefficients extracted in the weighted CELP coding error (lower-band) and the higher-band input signal are encoded. In order to reduce allocation bits for spectral envelope coding, a new quantization algorithm based on NLMS is proposed. Also, reduced bits are used to enhance sound quality. The performance of the proposed algorithm is evaluated by sound quality and bit reduction rates in clean and frame loss conditions.
Abstract: The catalytic dehydroxylation of glycerol to propylene
glycol was investigated over Cu-ZnO/Al2O3 prepared by incipient
wetness impregnation (IWI) method with different purity feedstocks -
refined glycerol and technical grade glycerol. The main purpose is to
investigate the effects of feed impurities that cause the catalyst
deactivation. The prepared catalyst were tested for its catalytic
activity and selectivity in a continuous flow fixed bed reactor at 523
K, 500 psig, H2/feed molar ratio of 4 and WHSV of 3 h-1. The results
showed that conversion of refined glycerol and technical grade
glycerol at time on stream 6 hour are 99% and 71% and selectivity to
propylene glycol are 87% and 56% respectively. The ICP-EOS and
TPO results indicated that the cause of catalyst deactivation was the
amount of impurities in the feedstock. The higher amount of
impurities (especially Na and K) the lower catalytic activity.
Abstract: In hydrocyclones, the particle separation efficiency is
limited by the suspended fine particles, which are discharged with the
coarse product in the underflow. It is well known that injecting water
in the conical part of the cyclone reduces the fine particle fraction in
the underflow. This paper presents a mathematical model that
simulates the water injection in the conical component. The model
accounts for the fluid flow and the particle motion. Particle
interaction, due to hindered settling caused by increased density and
viscosity of the suspension, and fine particle entrainment by settling
coarse particles are included in the model. Water injection in the
conical part of the hydrocyclone is performed to reduce fine particle
discharge in the underflow. The model demonstrates the impact of
the injection rate, injection velocity, and injection location on the
shape of the partition curve. The simulations are compared with
experimental data of a 50-mm cyclone.
Abstract: CONWIP (constant work-in-process) as a pull
production system have been widely studied by researchers to date.
The CONWIP pull production system is an alternative to pure push
and pure pull production systems. It lowers and controls inventory
levels which make the throughput better, reduces production lead
time, delivery reliability and utilization of work. In this article a
CONWIP pull production system was simulated. It was simulated
push and pull planning system. To compare these systems via a
production planning system (PPS) game were adjusted parameters of
each production planning system. The main target was to reduce the
total WIP and achieve throughput and delivery reliability to
minimum values. Data was recorded and evaluated. A future state
was made for real production of plastic components and the setup of
the two indicators with CONWIP pull production system which can
greatly help the company to be more competitive on the market.
Abstract: A new current-mode multifunction filter using minimum number of passive elements is proposed. The proposed filter has single-input and four high-impedance outputs. It uses four passive elements (two capacitors and two resistors) and four dual output second generation current conveyors. Each output provides a different filter response, namely, low-pass, high-pass, band-pass and band-reject. The sensitivity analysis is also carried out on both ideal and non-ideal filter configurations. The validity of the proposed filter is verified through PSPICE simulations.
Abstract: Wireless sensor networks (WSNs) consist of number
of tiny, low cost and low power sensor nodes to monitor some physical phenomenon. The major limitation in these networks is the use of non-rechargeable battery having limited power supply. The
main cause of energy consumption in such networks is
communication subsystem. This paper presents an energy efficient
Cluster Cooperative Caching at Sensor (C3S) based upon grid type clustering. Sensor nodes belonging to the same cluster/grid form a
cooperative cache system for the node since the cost for
communication with them is low both in terms of energy
consumption and message exchanges. The proposed scheme uses
cache admission control and utility based data replacement policy to
ensure that more useful data is retained in the local cache of a node.
Simulation results demonstrate that C3S scheme performs better in
various performance metrics than NICoCa which is existing
cooperative caching protocol for WSNs.
Abstract: Applying corona wind as a novel technique can lead
to a great level of heat and mass transfer augmentation by using very
small amount of energy. Enhancement of forced flow evaporation
rate by applying electric field (corona wind) has been experimentally
evaluated in this study. Corona wind produced by a fine wire
electrode which is charged with positive high DC voltage impinges
to water surface and leads to evaporation enhancement by disturbing
the saturated air layer over water surface. The study was focused on
the effect of corona wind velocity, electrode spacing and air flow
velocity on the level of evaporation enhancement. Two sets of
experiments, i.e. with and without electric field, have been
conducted. Data obtained from the first experiment were used as
reference for evaluation of evaporation enhancement at the presence
of electric field. Applied voltages ranged from corona threshold
voltage to spark over voltage at 1 kV increments. The results showed
that corona wind has great enhancement effect on water evaporation
rate, but its effectiveness gradually diminishes by increasing air flow
velocity. Maximum enhancements were 7.3 and 3.6 for air velocities
of 0.125 and 1.75 m/s, respectively.
Abstract: Wireless sensor network is formed with the combination of sensor nodes and sink nodes. Recently Wireless sensor network has attracted attention of the research community. The main application of wireless sensor network is security from different attacks both for mass public and military. However securing these networks, by itself is a critical issue due to many constraints like limited energy, computational power and lower memory. Researchers working in this area have proposed a number of security techniques for this purpose. Still, more work needs to be done.In this paper we provide a detailed discussion on security in wireless sensor networks. This paper will help to identify different obstacles and requirements for security of wireless sensor networks as well as highlight weaknesses of existing techniques.
Abstract: The general idea behind the filter is to average a pixel
using other pixel values from its neighborhood, but simultaneously to
take care of important image structures such as edges. The main
concern of the proposed filter is to distinguish between any variations
of the captured digital image due to noise and due to image structure.
The edges give the image the appearance depth and sharpness. A
loss of edges makes the image appear blurred or unfocused.
However, noise smoothing and edge enhancement are traditionally
conflicting tasks. Since most noise filtering behaves like a low pass
filter, the blurring of edges and loss of detail seems a natural
consequence. Techniques to remedy this inherent conflict often
encompass generation of new noise due to enhancement.
In this work a new fuzzy filter is presented for the noise reduction
of images corrupted with additive noise. The filter consists of three
stages. (1) Define fuzzy sets in the input space to computes a fuzzy
derivative for eight different directions (2) construct a set of IFTHEN
rules by to perform fuzzy smoothing according to
contributions of neighboring pixel values and (3) define fuzzy sets in
the output space to get the filtered and edged image.
Experimental results are obtained to show the feasibility of the
proposed approach with two dimensional objects.
Abstract: Fly ash is one of the residues generated in
combustion, and comprises the fine particles that rise with the flue
gases. Ash which does not rise is termed bottom ash [1]. In our
country, it is expected that will be occurred 50 million tons of waste
ash per year until 2020. Released waste from the thermal power
plants is caused very significant problems as known. The fly ashes
can be evaluated by using as adsorbent material.
The purpose of this study is to investigate the possibility of use of
Tuncbilek fly ash like low-cost adsorbents for heavy metal
adsorption. First of all, Tuncbilek fly ash was characterized. For this
purpose; analysis such as sieve analysis, XRD, XRF, SEM and FT-IR
were performed.
Abstract: In this study, the kinetics of osmotic dehydration of melons (Tille variety) in a ternary system followed by air-drying for preserving melons in the summer to be used in the winter were investigated. The effect of different osmotic solution concentrations 30, 40 and 50% (w/w) of sucrose with 10% NaCl salt and fruit to solution ratios 1:4, 1:5 and 1:6 on the mass transfer kinetics during osmotic dehydration of melon in ternary solution namely sucrosesalt- water followed by air-drying were studied. The diffusivity of water during air-drying was enhanced after the fruit samples were immersed in the osmotic solution after 60 min. Samples non-treated and pre-treated during one hour in osmotic solutions with 60% (w/w) of sucrose with 10% NaCl salt and fruit to solution ratio of 1:4 were dried in a hot air-dryer at 60oC (2 m/s) until equilibrium was achieved.
Abstract: This research was to study effect of rotational speed
and eccentric factors, which were affected on looseness of bearing.
The experiment was conducted on three rotational speeds and five
eccentric distances with 5 replications. The results showed that
influenced factor affected to looseness of bearing was rotational
speed and eccentric distance which showed statistical significant.
Higher rotational speed would cause on high looseness. Moreover,
more eccentric distance, more looseness of bearing. Using bearing at
high rotational with high eccentric of shaft would be affected
bearing fault more than lower rotational speed. The prediction
equation of looseness was generated by regression analysis. The
prediction has an effected to the looseness of bearing at 91.5%.
Abstract: Image interpolation is a common problem in imaging applications. However, most interpolation algorithms in existence suffer visually the effects of blurred edges and jagged artifacts in the image to some extent. This paper presents an adaptive feature preserving bidirectional flow process, where an inverse diffusion is performed to sharpen edges along the normal directions to the isophote lines (edges), while a normal diffusion is done to remove artifacts (“jaggies") along the tangent directions. In order to preserve image features such as edges, corners and textures, the nonlinear diffusion coefficients are locally adjusted according to the directional derivatives of the image. Experimental results on synthetic images and nature images demonstrate that our interpolation algorithm substantially improves the subjective quality of the interpolated images over conventional interpolations.
Abstract: The present study investigates numerically the
phenomenon of vortex-shedding and its suppression in twodimensional
mixed convective flow past a square cylinder under the
joint influence of buoyancy and free-stream orientation with respect
to gravity. The numerical experiments have been conducted at a
fixed Reynolds number (Re) of 100 and Prandtl number (Pr) of 0.71,
while Richardson number (Ri) is varied from 0 to 1.6 and freestream
orientation, α, is kept in the range 0o≤ α ≤ 90o, with 0o
corresponding to an upward flow and 90o representing a cross-flow
scenario, respectively. The continuity, momentum and energy
equations, subject to Boussinesq approximation, are discretized using
a finite difference method and are solved by a semi-explicit pressure
correction scheme. The critical Richardson number, leading to the
suppression of the vortex-shedding (Ric), is estimated by using
Stuart-Landau theory at various free-stream orientations and the
neutral curve is obtained in the Ri-α plane. The neutral curve
exhibits an interesting non-monotonic behavior with Ric first
increasing with increasing values of α upto 45o and then decreasing
till 70o. Beyond 70o, the neutral curve again exhibits a sharp
increasing asymptotic trend with Ric approaching very large values
as α approaches 90o. The suppression of vortex shedding is not
observed at α = 90o (cross-flow). In the unsteady flow regime, the
Strouhal number (St) increases with the increase in Richardson
number.
Abstract: In text categorization problem the most used method
for documents representation is based on words frequency vectors
called VSM (Vector Space Model). This representation is based only
on words from documents and in this case loses any “word context"
information found in the document. In this article we make a
comparison between the classical method of document representation
and a method called Suffix Tree Document Model (STDM) that is
based on representing documents in the Suffix Tree format. For the
STDM model we proposed a new approach for documents
representation and a new formula for computing the similarity
between two documents. Thus we propose to build the suffix tree
only for any two documents at a time. This approach is faster, it has
lower memory consumption and use entire document representation
without using methods for disposing nodes. Also for this method is
proposed a formula for computing the similarity between documents,
which improves substantially the clustering quality. This
representation method was validated using HAC - Hierarchical
Agglomerative Clustering. In this context we experiment also the
stemming influence in the document preprocessing step and highlight
the difference between similarity or dissimilarity measures to find
“closer" documents.
Abstract: The intent of this essay is to evaluate the effectiveness
of surge suppressor aimed at power supply used for automation
devices in power distribution system which is consist of MOV and
T type low-pass filter. Books, journal articles and e-sources related
to surge protection of power supply used for automation devices in
power distribution system were consulted, and the useful information
was organized, analyzed and developed into five parts: characteristics
of surge wave, protection against surge wave, impedance characteristics
of target, using Matlab to simulate circuit response after
5kV,1.2/50s surge wave and suggestions for surge protection. The
results indicate that various types of load situation have great impact
on the effectiveness of surge protective device. Therefore, type and
parameters of surge protective device need to be carefully selected,
and load matching is also vital to be concerned.