Abstract: This work addresses the problem of optimizing
completely batch water-using network with multiple contaminants
where the flow change caused by mass transfer is taken into
consideration for the first time. A mathematical technique for
optimizing water-using network is proposed based on
source-tank-sink superstructure. The task is to obtain the freshwater
usage, recycle assignments among water-using units, wastewater
discharge and a steady water-using network configuration by
following steps. Firstly, operating sequences of water-using units are
determined by time constraints. Next, superstructure is simplified by
eliminating the reuse and recycle from water-using units with
maximum concentration of key contaminants. Then, the non-linear
programming model is solved by GAMS (General Algebra Model
System) for minimum freshwater usage, maximum water recycle and
minimum wastewater discharge. Finally, numbers of operating periods
are calculated to acquire the steady network configuration. A case
study is solved to illustrate the applicability of the proposed approach.
Abstract: Buildings are one of the valuable assets to provide
people with shelters for work, leisure and rest. After years of
attacks by weather, buildings will deteriorate which need proper
maintenance in order to fulfill the requirements and satisfaction of
the users. Poorly managed buildings not just give a negative image
to the city itself, but also pose potential risk hazards to the health
and safety of the general public. As a result, the management of
maintenance projects has played an important role in cities like
Hong Kong where the problem of urban decay has drawn much
attention. However, most research has focused on managing new
construction, and little research effort has been put on maintenance
projects. Given the short duration and more diversified nature of
work, repair and maintenance works are found to be more difficult
to monitor and regulate when compared with new works. Project
participants may face with problems in running maintenance
projects which should be investigated so that proper strategies can
be established. This paper aims to provide a thorough analysis on
the problems of running maintenance projects. A review of
literature on the characteristics of building maintenance projects
was firstly conducted, which forms a solid basis for the empirical
study. Results on the problems and difficulties of running
maintenance projects from the viewpoints of industry practitioners
will also be delivered with a view to formulating effective
strategies for managing maintenance projects successfully.
Abstract: Although e-mail is the most efficient and popular communication method, unwanted and mass unsolicited e-mails, also called spam mail, endanger the existence of the mail system. This paper proposes a new algorithm called Dynamic Weighted Majority Concept Drift Detection (DWM-CDD) for content-based filtering. The design purposes of DWM-CDD are first to accurate the performance of the previously proposed algorithms, and second to speed up the time to construct the model. The results show that DWM-CDD can detect both sudden and gradual changes quickly and accurately. Moreover, the time needed for model construction is less than previously proposed algorithms.
Abstract: The gas safety management system using an
intelligent gas meter we proposed is to monitor flow and
pressure of gas, earthquake, temperature, smoke and leak of
methane. Then our system takes safety measures to protect a
serious risk by the result of an event, to communicate with a
wall-pad including a gateway by zigbee network in buildings
and to report the event to user by the safety management
program in a server. Also, the inner cutoff valve of an
intelligent gas meter is operated if any event occurred or
abnormal at each sensor.
Abstract: In this project cadmium ions were adsorbed from
aqueous solutions onto either date pits; a cheap agricultural and nontoxic
material, or chemically activated carbon prepared from date pits
using phosphoric acid. A series of experiments were conducted in a
batch adsorption technique to assess the feasibility of using the
prepared adsorbents. The effects of the process variables such as
initial cadmium ions concentration, contact time, solution pH and
adsorbent dose on the adsorption capacity of both adsorbents were
studied. The experimental data were tested using different isotherm
models such as Langmuir, Freundlich, Tempkin and Dubinin-
Radushkevich. The results showed that although the equilibrium data
could be described by all models used, Langmuir model gave slightly
better results when using activated carbon while Freundlich model,
gave better results with date pits.
Abstract: Today air-core coils (ACC) are a viable alternative to
ferrite-core coils in a range of applications due to their low induction
effect. An analytical study was carried out and the results were used as
a guide to understand the relationship between the magnet-coil
distance and the resulting attractive magnetic force. Four different
ACC models were fabricated for experimental study. The variation in
the models included the dimensions, the number of coil turns and the
current supply to the coil. Comparison between the analytical and
experimental results for all the models shows an average discrepancy
of less than 10%. An optimized ACC design was selected for the
scanner which can provide maximum magnetic force.
Abstract: EPC Class-1 Generation-2 UHF tags, one of Radio
frequency identification or RFID tag types, is expected that most
companies are planning to use it in the supply chain in the short term
and in consumer packaging in the long term due to its inexpensive
cost. Because of the very cost, however, its resources are extremely
scarce and it is hard to have any valuable security algorithms in it. It
causes security vulnerabilities, in particular cloning the tags for
counterfeits. In this paper, we propose a product authentication
solution for anti-counterfeiting at application level in the supply chain
and mobile RFID environment. It aims to become aware of
distribution of spurious products with fake RFID tags and to provide a
product authentication service to general consumers with mobile
RFID devices like mobile phone or PDA which has a mobile RFID
reader. We will discuss anti-counterfeiting mechanisms which are
required to our proposed solution and address requirements that the
mechanisms should have.
Abstract: Tip vortex cavitation is one of well known patterns of
cavitation phenomenon which occurs in axial pumps. This pattern of
cavitation occurs due to pressure difference between the pressure and
suction sides of blades of an axial pump. Since the pressure in the
pressure side of the blade is higher than the pressure in its suction
side, thus a very small portion of liquid flow flows back from
pressure side to the suction side. This fact is cause of tip vortex
cavitation and gap cavitation that may occur in axial pumps. In this
paper the results of our experimental investigation about movement
of tip vortex cavitation along blade edge due to reduction of pump
flow rate in an axial pump is reported. Results show that reduction of
pump flow rate in conjunction with increasing of outlet pressure
causes movement of tip vortex cavitation along blade edge towards
the blade tip. Results also show that by approaching tip vortex
cavitation to the blade tip, vortex tip pattern of cavitation replaces
with a cavitation phenomenon on the blade tip. Furthermore by
further reduction of pump flow rate and increasing of outlet pressure,
an unstable cavitation phenomenon occurs between each blade
leading edge and the next blade trailing edge.
Abstract: The decision to recruit manpower in an organization
requires clear identification of the criteria (attributes) that distinguish
successful from unsuccessful performance. The choice of appropriate
attributes or criteria in different levels of hierarchy in an organization
is a multi-criteria decision problem and therefore multi-criteria
decision making (MCDM) techniques can be used for prioritization
of such attributes. Analytic Hierarchy Process (AHP) is one such
technique that is widely used for deciding among the complex criteria
structure in different levels. In real applications, conventional AHP
still cannot reflect the human thinking style as precise data
concerning human attributes are quite hard to be extracted. Fuzzy
logic offers a systematic base in dealing with situations, which are
ambiguous or not well defined. This study aims at defining a
methodology to improve the quality of prioritization of an
employee-s performance measurement attributes under fuzziness. To
do so, a methodology based on the Extent Fuzzy Analytic Hierarchy
Process is proposed. Within the model, four main attributes such as
Subject knowledge and achievements, Research aptitude, Personal
qualities and strengths and Management skills with their subattributes
are defined. The two approaches conventional AHP
approach and the Extent Fuzzy Analytic Hierarchy Process approach
have been compared on the same hierarchy structure and criteria set.
Abstract: By using the method of coincidence degree and constructing suitable Lyapunov functional, some sufficient conditions are established for the existence and global exponential stability of antiperiodic solutions for a kind of impulsive Cohen-Grossberg shunting inhibitory cellular neural networks (CGSICNNs) on time scales. An example is given to illustrate our results.
Abstract: Selective oxidation of H2S to elemental sulfur in a
fixed bed reactor over newly synthesized alumina nanocatalysts was
physio-chemically investigated and results compared with a
commercial Claus catalyst. Amongst these new materials, Al2O3-
supported sodium oxide prepared with wet chemical technique and
Al2O3 nanocatalyst prepared with spray pyrolysis method were the
most active catalysts for selective oxidation of H2S to elemental
sulfur. Other prepared nanocatalysts were quickly deactivated,
mainly due to the interaction with H2S and conversion into sulfides.
Abstract: Polyphenolics and sugar are the components of many
fruit juices. In this work, the performance of ultra-filtration (UF) for
separating phenolic compounds from apple juice was studied by
performing batch experiments in a membrane module with an area of
0.1 m2 and fitted with a regenerated cellulose membrane of 1 kDa
MWCO. The effects of various operating conditions: transmembrane
pressure (3, 4, 5 bar), temperature (30, 35, 40 ºC), pH (2, 3, 4, 5),
feed concentration (3, 5, 7, 10, 15 ºBrix for apple juice) and feed flow
rate (1, 1.5, 1.8 L/min) on the performance were determined.
The optimum operating conditions were: transmembrane pressure
4 bar, temperature 30 ºC, feed flow rate 1 – 1.8 L/min, pH 3 and 10
Brix (apple juice). After performing ultrafiltration under these
conditions, the concentration of polyphenolics in retentate was
increased by a factor of up to 2.7 with up to 70% recovered in the
permeate and with approx. 20% of the sugar in that stream..
Application of diafiltration (addition of water to the concentrate) can
regain the flux by a factor of 1.5, which has been decreased due to
fouling. The material balance performed on the process has shown
the amount of deposits on the membrane and the extent of fouling in
the system. In conclusion, ultrafiltration has been demonstrated as a
potential technology to separate the polyphenolics and sugars from
their mixtures and can be applied to remove sugars from fruit juice.
Abstract: Contractor selection in Saudi Arabia is very important due to the large construction boom and the contractor role to get over construction risks. The need for investigating contractor selection is due to the following reasons; large number of defaulted or failed projects (18%), large number of disputes attributed to contractor during the project execution stage (almost twofold), the extension of the General Agreement on Tariffs and Trade (GATT) into construction industry, and finally the few number of researches. The selection strategy is not perfect and considered as the reason behind irresponsible contractors. As a response, this research was conducted to review the contractor selection strategies as an integral part of a long advanced research to develop a good selection model. Many techniques can be used to form a selection strategy; multi criteria for optimizing decision, prequalification to discover contractor-s responsibility, bidding process for competition, third party guarantee to enhance the selection, and fuzzy techniques for ambiguities and incomplete information.
Abstract: Three service providers in competition, try to optimize
their quality of service / content level and their service access
price. But, they have to deal with uncertainty on the consumers-
preferences. To reduce their uncertainty, they have the opportunity
to buy information and to build alliances. We determine the Shapley
value which is a fair way to allocate the grand coalition-s revenue
between the service providers. Then, we identify the values of β
(consumers- sensitivity coefficient to the quality of service / contents)
for which allocating the grand coalition-s revenue using the Shapley
value guarantees the system stability. For other values of β, we prove
that it is possible for the regulator to impose a per-period interest rate
maximizing the market coverage under equal allocation rules.
Abstract: Compression algorithms reduce the redundancy in
data representation to decrease the storage required for that data.
Lossless compression researchers have developed highly
sophisticated approaches, such as Huffman encoding, arithmetic
encoding, the Lempel-Ziv (LZ) family, Dynamic Markov
Compression (DMC), Prediction by Partial Matching (PPM), and
Burrows-Wheeler Transform (BWT) based algorithms.
Decompression is also required to retrieve the original data by
lossless means. A compression scheme for text files coupled with
the principle of dynamic decompression, which decompresses only
the section of the compressed text file required by the user instead of
decompressing the entire text file. Dynamic decompressed files offer
better disk space utilization due to higher compression ratios
compared to most of the currently available text file formats.
Abstract: When a high DC voltage is applied to a capacitor with
strongly asymmetrical electrodes, it generates a mechanical force that
affects the whole capacitor. This phenomenon is most likely to be
caused by the motion of ions generated around the smaller of the two
electrodes and their subsequent interaction with the surrounding
medium. A method to measure this force has been devised and used.
A formula describing the force has also been derived. After
comparing the data gained through experiments with those acquired
using the theoretical formula, a difference was found above a certain
value of current. This paper also gives reasons for this difference.
Abstract: This article presents a computationally tractable probabilistic model for the relation between the complex wavelet coefficients of two images of the same scene. The two images are acquisitioned at distinct moments of times, or from distinct viewpoints, or by distinct sensors. By means of the introduced probabilistic model, we argue that the similarity between the two images is controlled not by the values of the wavelet coefficients, which can be altered by many factors, but by the nature of the wavelet coefficients, that we model with the help of hidden state variables. We integrate this probabilistic framework in the construction of a new image registration algorithm. This algorithm has sub-pixel accuracy and is robust to noise and to other variations like local illumination changes. We present the performance of our algorithm on various image types.
Abstract: Interior brick-infill partitions are usually considered as
non-structural components, and only their weight is accounted for in
practical structural design. In this study, the brick-infill panels are
simulated by compression struts to clarify their effect on the
progressive collapse potential of an earthquake-resistant RC building.
Three-dimensional finite element models are constructed for the RC
building subjected to sudden column loss. Linear static analyses are
conducted to investigate the variation of demand-to-capacity ratio
(DCR) of beam-end moment and the axial force variation of the beams
adjacent to the removed column. Study results indicate that the
brick-infill effect depends on their location with respect to the
removed column. As they are filled in a structural bay with a shorter
span adjacent to the column-removed line, more significant reduction
of DCR may be achieved. However, under certain conditions, the
brick infill may increase the axial tension of the two-span beam
bridging the removed column.
Abstract: Conventional concentrically-braced frame (CBF)
systems have limited drift capacity before brace buckling and related
damage leads to deterioration in strength and stiffness. Self-centering
concentrically-braced frame (SC-CBF) systems have been developed
to increase drift capacity prior to initiation of damage and minimize
residual drift. SC-CBFs differ from conventional CBFs in that the
SC-CBF columns are designed to uplift from the foundation at a
specified level of lateral loading, initiating a rigid-body rotation
(rocking) of the frame. Vertically-aligned post-tensioning bars resist
uplift and provide a restoring force to return the SC-CBF columns to
the foundation (self-centering the system). This paper presents a
parametric study of different prototype buildings using SC-CBFs.
The bay widths of the SC-CBFs have been varied in these buildings
to study different geometries. Nonlinear numerical analyses of the
different SC-CBFs are presented to illustrate the effect of frame
geometry on the behavior and dynamic response of the SC-CBF
system.
Abstract: An appropriate project delivery system (PDS) is crucial
to the success of a construction projects. Case-based Reasoning (CBR)
is a useful support for PDS selection. However, the traditional CBR
approach represents cases as attribute-value vectors without taking
relations among attributes into consideration, and could not calculate
the similarity when the structures of cases are not strictly same.
Therefore, this paper solves this problem by adopting the Relational
Case-based Reasoning (RCBR) approach for PDS selection,
considering both the structural similarity and feature similarity. To
develop the feature terms of the construction projects, the criteria and
factors governing PDS selection process are first identified. Then
feature terms for the construction projects are developed. Finally, the
mechanism of similarity calculation and a case study indicate how
RCBR works for PDS selection. The adoption of RCBR in PDS
selection expands the scope of application of traditional CBR method
and improves the accuracy of the PDS selection system.