Abstract: In this paper, a Dynamic Economic Dispatch (DED) model is developed for the system consisting of both thermal generators and wind turbines. The inclusion of a significant amount of wind energy into power systems has resulted in additional constraints on DED to accommodate the intermittent nature of the output. The probability of stochastic wind power based on the Weibull probability density function is included in the model as a constraint; A Here-and-Now Approach. The Environmental Protection Agency-s hourly emission target, which gives the maximum emission during the day, is used as a constraint to reduce the atmospheric pollution. A 69-bus test system with non-smooth cost function is used to illustrate the effectiveness of the proposed model compared with static economic dispatch model with including the wind power.
Abstract: In this note, a theoretical model for analyzing of
normal penetration of the ogive – nose projectile into metallic targets
is presented .The failure is assumed to be asymmetry petalling and
the analysis is performed by using the energy balance and work done
.The work done consist of the work required for plastic deformation
Wp, the work for transferring the matter to new position Wd and the
work for bending of the petals Wb. In several studies, it has been
shown that we can neglect the loss of energy by temperature.
In this present study, in first, by assuming the crater formation
after perforation, the value of work done is calculated during the
normal penetration of conical projectiles into thin metallic targets.
Then the value of residual velocity and ballistic limit of the projectile
is predicated by using the energy balance. In final, theoretical and
experimental results is compared.
Abstract: Sensor Network are emerging as a new tool for
important application in diverse fields like military surveillance,
habitat monitoring, weather, home electrical appliances and others.
Technically, sensor network nodes are limited in respect to energy
supply, computational capacity and communication bandwidth. In
order to prolong the lifetime of the sensor nodes, designing efficient
routing protocol is very critical. In this paper, we illustrate the
existing routing protocol for wireless sensor network using data
centric approach and present performance analysis of these protocols.
The paper focuses in the performance analysis of specific protocol
namely Directed Diffusion and SPIN. This analysis reveals that the
energy usage is important features which need to be taken into
consideration while designing routing protocol for wireless sensor
network.
Abstract: Thepurpose of the research is to characterize the levels
of satisfaction of the students in e-learning post-graduate courses,
taking into account specific dimensions of the course which were
considered as benchmarks for the quality of this type of online
learning initiative, as well as the levels of satisfaction towards each
specific indicator identified in each dimension. It was also an aim of
this study to understand how thesedimensions relate to one another.
Using a quantitative research approach in the collection and analysis
of the data, the study involves the participation of the students who
attended on e-learning course in 2010/2011. The conclusions of this
study suggest that online students present relatively high levels of
satisfaction, which points towards a positive experience during the
course. It is possible to note that there is a correlation between the
different dimensions studied, consequently leading to different
improvement strategies. Ultimately, this investigation aims to
contribute to the promotion of quality and the success of e-learning
initiatives in Higher Education.
Abstract: In this paper, a comparative study of application of
supervised and unsupervised learning algorithms on illumination
invariant face recognition has been carried out. The supervised
learning has been carried out with the help of using a bi-layered
artificial neural network having one input, two hidden and one output
layer. The gradient descent with momentum and adaptive learning
rate back propagation learning algorithm has been used to implement
the supervised learning in a way that both the inputs and
corresponding outputs are provided at the time of training the
network, thus here is an inherent clustering and optimized learning of
weights which provide us with efficient results.. The unsupervised
learning has been implemented with the help of a modified
Counterpropagation network. The Counterpropagation network
involves the process of clustering followed by application of Outstar
rule to obtain the recognized face. The face recognition system has
been developed for recognizing faces which have varying
illumination intensities, where the database images vary in lighting
with respect to angle of illumination with horizontal and vertical
planes. The supervised and unsupervised learning algorithms have
been implemented and have been tested exhaustively, with and
without application of histogram equalization to get efficient results.
Abstract: Complex assemblies of interacting proteins carry out
most of the interesting jobs in a cell, such as metabolism, DNA
synthesis, mitosis and cell division. These physiological properties
play out as a subtle molecular dance, choreographed by underlying
regulatory networks that control the activities of cyclin-dependent
kinases (CDK). The network can be modeled by a set of nonlinear
differential equations and its behavior predicted by numerical
simulation. In this paper, an innovative approach has been proposed
that uses genetic algorithms to mine a set of behavior data output by
a biological system in order to determine the kinetic parameters of
the system. In our approach, the machine learning method is
integrated with the framework of existent biological information in a
wiring diagram so that its findings are expressed in a form of system
dynamic behavior. By numerical simulations it has been illustrated
that the model is consistent with experiments and successfully shown
that such application of genetic algorithms will highly improve the
performance of mathematical model of the cell division cycle to
simulate such a complicated bio-system.
Abstract: The issue of real-time and reliable report delivery is extremely important for taking effective decision in a real world mission critical Wireless Sensor Network (WSN) based application. The sensor data behaves differently in many ways from the data in traditional databases. WSNs need a mechanism to register, process queries, and disseminate data. In this paper we propose an architectural framework for data placement and management. We propose a reliable and real time approach for data placement and achieving data integrity using self organized sensor clusters. Instead of storing information in individual cluster heads as suggested in some protocols, in our architecture we suggest storing of information of all clusters within a cell in the corresponding base station. For data dissemination and action in the wireless sensor network we propose to use Action and Relay Stations (ARS). To reduce average energy dissipation of sensor nodes, the data is sent to the nearest ARS rather than base station. We have designed our architecture in such a way so as to achieve greater energy savings, enhanced availability and reliability.
Abstract: The mechanical deformation and the electrical conductivity of lanthanum strontium cobalt ferrite oxide under uniaxial compression were investigated at various temperatures up to 1073 K. The material reveals a rather complex mechanical behaviour related to its ferroelasticity and completely different stress-strain curves are obtained during the 1st and 2nd loading cycles. A distinctive ferroelastic creep was observed at 293 K whilst typical ferroelastic stress-strain curve were obtained in the temperature range from 473 K to 873 K. At 1073 K, on the other hand, high-temperature creep deformation was observed instead of ferroelastic deformation. The conductivity increases with increasing compressive stress at all the temperatures. The increase in conductivity is related to both geometrical and piezoelectric effects. From 293 K to 873 K, where the material exhibits ferroelastic behaviour, the variation in the total conductivity decreases with increasing temperature. The contribution of the piezoelectric effect to the total conductivity variation also decreases with increasing temperature and the maximum in piezoconductivity has a value of about 0.75 % at 293 K for a compressive stress of 100 MPa. There is no effect of domain switching on conductivity except for the geometric effect. At 1073 K, the conductivity is simply proportional to the compressive strain.
Abstract: Image clustering is a process of grouping images
based on their similarity. The image clustering usually uses the color
component, texture, edge, shape, or mixture of two components, etc.
This research aims to explore image clustering using color
composition. In order to complete this image clustering, three main
components should be considered, which are color space, image
representation (feature extraction), and clustering method itself. We
aim to explore which composition of these factors will produce the
best clustering results by combining various techniques from the
three components. The color spaces use RGB, HSV, and L*a*b*
method. The image representations use Histogram and Gaussian
Mixture Model (GMM), whereas the clustering methods use KMeans
and Agglomerative Hierarchical Clustering algorithm. The
results of the experiment show that GMM representation is better
combined with RGB and L*a*b* color space, whereas Histogram is
better combined with HSV. The experiments also show that K-Means
is better than Agglomerative Hierarchical for images clustering.
Abstract: Protective effect of ethanolic extract of polyherbal formulation (PHF) was studied on carbon tetrachloride induced liver damage on carbon tetrachloride induced liver damage. Treatment of rats with 250mg /kg body weight of ethanolic extract of PHF protected rats against carbon tetrachloride liver injury by significant lowerering 5’ nucleotidase (5’NT), Gamma Glutamyl transferase (GGT), Glutamate dehdyrogenasse (GDH) and Succinate Dehydrogenase (SDH) levels compared to control. Normalization in these enzyme levels indicates strong hepatoprotective property of PHF extract.
Abstract: Gliding during night without electric power is an efficient method to enhance endurance performance of solar aircrafts. The properties of maximum gliding endurance path are studied in this paper. The problem is formulated as an optimization problem about maximum endurance can be sustained by certain potential energy storage with dynamic equations and aerodynamic parameter constrains. The optimal gliding path is generated based on gauss pseudo-spectral method. In order to analyse relationship between altitude, velocity of solar UAVs and its endurance performance, the lift coefficient in interval of [0.4, 1.2] and flight envelopes between 0~30km are investigated. Results show that broad range of lift coefficient can improve solar aircrafts- long endurance performance, and it is possible for a solar aircraft to achieve the aim of long endurance during whole night just by potential energy storage.
Abstract: In this paper we propose a method which improves the efficiency of video coding. Our method combines an adaptive GOP (group of pictures) structure and the shot cut detection. We have analyzed different approaches for shot cut detection with aim to choose the most appropriate one. The next step is to situate N frames to the positions of detected cuts during the process of video encoding. Finally the efficiency of the proposed method is confirmed by simulations and the obtained results are compared with fixed GOP structures of sizes 4, 8, 12, 16, 32, 64, 128 and GOP structure with length of entire video. Proposed method achieved the gain in bit rate from 0.37% to 50.59%, while providing PSNR (Peak Signal-to-Noise Ratio) gain from 1.33% to 0.26% in comparison to simulated fixed GOP structures.
Abstract: The main emphasis of metallurgists has been to process the materials to obtain the balanced mechanical properties for the given application. One of the processing routes to alter the properties is heat treatment. Nearly 90% of the structural applications are related to the medium carbon an alloyed steels and hence are regarded as structural steels. The major requirement in the conventional steel is to improve workability, toughness, hardness and grain refinement. In this view, it is proposed to study the mechanical and tribological properties of unalloyed structural (AISI 1140) steel with different thermal (heat) treatments like annealing, normalizing, tempering and hardening and compared with as brought (cold worked) specimen. All heat treatments are carried out in atmospheric condition. Hardening treatment improves hardness of the material, a marginal decrease in hardness value with improved ductility is observed in tempering. Annealing and normalizing improve ductility of the specimen. Normalized specimen shows ultimate ductility. Hardened specimen shows highest wear resistance in the initial period of slide wear where as above 25KM of sliding distance, as brought steel dominates the hardened specimen. Both mild and severe wear regions are observed. Microstructural analysis shows the existence of pearlitic structure in normalized specimen, lath martensitic structure in hardened, pearlitic, ferritic structure in annealed specimen.
Abstract: In this paper the features of multiple material gate
silicon-on-insulator MOSFETs are presented and compared with
single material gate silicon-on-insulator MOSFET structures. The
results indicate that the multiple material gate structures reduce short
channel effects such as drain induce barrier lowering, hot electron
effect and better current characteristics in comparison with single
material structures
Abstract: A new, combinatorial model for analyzing and inter-
preting an electrocardiogram (ECG) is presented. An application of
the model is QRS peak detection. This is demonstrated with an
online algorithm, which is shown to be space as well as time efficient.
Experimental results on the MIT-BIH Arrhythmia database show that
this novel approach is promising. Further uses for this approach are
discussed, such as taking advantage of its small memory requirements
and interpreting large amounts of pre-recorded ECG data.
Abstract: Pyrolysis of waste tire is one of alternative technique
to produce petrochemicals, such as light olefins, mixed C4, and monoaromatics.
Noble metals supported on acid zeolite catalysts were
reported as potential catalysts to produce the high valuable products
from waste tire pyrolysis. Especially, Pd supported on HBeta gave a
high yield of olefins, mixed C4, and mono-aromatics. Due to the high
prices of noble metals, the objective of this work was to investigate
whether or not a non-noble Ni metal can be used as a substitute of a
noble metal, Pd, supported on HBeta as a catalyst for waste tire pyrolysis.
Ni metal was selected in this work because Ni has high activity
in cracking, isomerization, hydrogenation and the ring opening of
hydrocarbons Moreover, Ni is an element in the same group as Pd
noble metal, which is VIIIB group, aiming to produce high valuable
products similarly obtained from Pd. The amount of Ni was varied as
5, 10, and 20% by weight, for comparison with a fixed 1 wt% Pd,
using incipient wetness impregnation. The results showed that as a
petrochemical-producing catalyst, 10%Ni/HBeta performed better
than 1%Pd/HBeta because it did not only produce the highest yield of
olefins and cooking gases, but the yields were also higher than
1%Pd/HBeta. 5%Ni/HBeta can be used as a substitute of
1%Pd/HBeta for similar crude production because its crude contains
the similar amounts of naphtha and saturated HCs, although it gave
no concentration of light mono-aromatics (C6-C11) in the oil. Additionally,
10%Ni/HBeta that gave high olefins and cooking gases was
found to give a fairly high concentration of the light mono-aromatics
in the oil.
Abstract: The present study examines the mediating effect of
online flow experience on the relationship between extraversionintroversion,
locus of control and loneliness, and depression and
satisfaction with life. The data was obtained using a structured
questionnaire prepared by adapting standardized scales available from
a sample of 102 engineering students from different technical
institutions at Bhubaneswar, India. The results indicate that there is a
positive significant relationship between introversion, external locus
of control, loneliness, depression and online flow experience, and
extraversion, internal locus of control and satisfaction with life. The
results also suggest that online flow experience mediates the
relationship between the aforementioned variables.
Abstract: Promoting critical thinking (CT) in an educational
setting has been appraised in order to enhance learning and
intellectual skills. In this study, a pedagogical course in a vocational
teacher education program in Turkey was designed by integrating CT
skill-based strategies/activities into the course content and CT skills
were means leading to intended course objectives. The purpose of the
study was to evaluate the importance of the course objectives, the
attainment of the objectives, and the effectiveness of teachinglearning
strategies/activities from prospective teachers- points of
view. The results revealed that although the students mostly
considered the course objectives important, they did not feel
competent in the attainment of all objectives especially in those
related to the main topic of Learning and those requiring higher order
thinking skills. On the other hand, the students considered the course
activities effective for learning and for the development of thinking
skills, especially, in interpreting, comparing, questioning,
contrasting, and forming relationships.
Abstract: The Spalart and Allmaras turbulence model has been
implemented in a numerical code to study the compressible turbulent
flows, which the system of governing equations is solved with a
finite volume approach using a structured grid. The AUSM+ scheme
is used to calculate the inviscid fluxes. Different benchmark
problems have been computed to validate the implementation and
numerical results are shown. A special Attention is paid to wall jet
applications. In this study, the jet is submitted to various wall
boundary conditions (adiabatic or uniform heat flux) in forced
convection regime and both two-dimensional and axisymmetric wall
jets are considered. The comparison between the numerical results
and experimental data has given the validity of this turbulence model
to study the turbulent wall jets especially in engineering applications.
Abstract: Today, Hydroforming technology provides an
attractive alternative to conventional matched die forming, especially
for cost-sensitive, lower volume production, and for parts with
irregular contours. In this study the critical fluid pressures which lead
to rupture in the workpiece has been investigated by theoretical and
finite element methods. The axisymmetric analysis was developed to
investigate the tearing phenomenon in cylindrical Hydroforming
Deep Drawing (HDD). By use of obtained equations the effect of
anisotropy, drawing ratio, sheet thickness and strain hardening
exponent on tearing diagram were investigated.