Abstract: The Greater Athens Area (GAA) faces photochemical
and particulate pollution episodes as a result of the combined effects
of local pollutant emissions, regional pollution transport, synoptic
circulation and topographic characteristics. The area has undergone
significant changes since the Athens 2004 Olympic Games because
of large scale infrastructure works that lead to the shift of population
to areas previously characterized as rural, the increase of the traffic
fleet and the operation of highways. However, few recent modelling
studies have been performed due to the lack of an accurate, updated
emission inventory. The photochemical modelling system
MM5/CAMx was applied in order to study the photochemical and
particulate pollution characteristics above the GAA for two distinct
ten-day periods in the summer of 2006 and 2010, where air pollution
episodes occurred. A new updated emission inventory was used
based on official data. Comparison of modeled results with
measurements revealed the importance and accuracy of the new
Athens emission inventory as compared to previous modeling
studies. The model managed to reproduce the local meteorological
conditions, the daily ozone and particulates fluctuations at different
locations across the GAA. Higher ozone levels were found at
suburban and rural areas as well as over the sea at the south of the
basin. Concerning PM10, high concentrations were computed at the
city centre and the southeastern suburbs in agreement with measured
data. Source apportionment analysis showed that different sources
contribute to the ozone levels, the local sources (traffic, port
activities) affecting its formation.
Abstract: In this study, we have collected cases with adipocere
formation, which were from the South Delhi region (average room
temperature 27-390C) and autopsied at our centre. Details of the
circumstances of the death, cause and time of death, surrounding
environment and demographic profile of the deceased were taken into
account. Total 16 cases were included in this study. Adipocere
formation was predominantly present over cheeks, shoulder, breast,
flanks, buttocks, and thighs. Out of 16, 11 cases were found in a dry
atmosphere, 5 cases were brought from the water. There were 5 cases
in which adipocere formation was seen in less than 2 days, and
among them, in 1 case, as early as one day. This study showed that
adipocere formation can be seen as early as 1 day in a hot and humid
environment.
Abstract: In the present study, analysis of heat transfer is carried
out in the slip flow region for the fluid flowing between two parallel
plates by employing the asymmetric heat fluxes at surface of the
plates. The flow is assumed to be hydrodynamically and thermally
fully developed for the analysis. The second order velocity slip and
viscous dissipation effects are considered for the analysis. Closed
form expressions are obtained for the Nusselt number as a function of
Knudsen number and modified Brinkman number. The limiting
condition of the present prediction for Kn = 0, Kn2 = 0, and Brq1 = 0
is considered and found to agree well with other analytical results.
Abstract: Current study established for EEG signal analysis in
patients with language disorder. Language disorder can be defined as
meaningful delay in the use or understanding of spoken or written
language. The disorder can include the content or meaning of
language, its form, or its use. Here we applied Z-score, power
spectrum, and coherence methods to discriminate the language
disorder data from healthy ones. Power spectrum of each channel in
alpha, beta, gamma, delta, and theta frequency bands was measured.
In addition, intra hemispheric Z-score obtained by scoring algorithm.
Obtained results showed high Z-score and power spectrum in
posterior regions. Therefore, we can conclude that peoples with
language disorder have high brain activity in frontal region of brain
in comparison with healthy peoples. Results showed that high coherence correlates with irregularities
in the ERP and is often found during complex task, whereas low
coherence is often found in pathological conditions. The results of the
Z-score analysis of the brain dynamics showed higher Z-score peak
frequency in delta, theta and beta sub bands of Language Disorder
patients. In this analysis there were activity signs in both hemispheres
and the left-dominant hemisphere was more active than the right.
Abstract: Urinary Tract Infections are considered as one of the
most common bacterial infections with an estimated annual global
incidence of 150 million. Antimicrobial drug resistance is one of the
major threats due to wide spread usage of uncontrolled antibiotics. In
this study, a total number of 9149 urine samples were collected from
R.H Patiala and processed in the Department of Microbiology G. M.
C Patiala (January 2013 to December 2013). Urine samples were
inoculated on MacConkey’s and blood agar plates and incubated at
370C for 24 hrs. The organisms were identified by colony characters,
Gram’s staining, and biochemical reactions. Antimicrobial
susceptibility of the isolates was determined against various
antimicrobial agents (Hi – Media Mumbai India) by Kirby Bauer
DISK diffusion method on Muller Hinton agar plates. Maximum patients were in the age group of 21-30 yrs followed by
31-40 yrs. Males (34%) are less prone to urinary tract infections than
females (66%). Culture was positive in 25% of the samples.
Escherichia coli was the most common isolate 60.3% followed by
Klebsiella pneumoniae 13.5%, Proteus spp. 9% and Staphylococcus
aureus 7.6%. Most of the urinary isolates were sensitive to,
carbepenems, Aztreonam, Amikacin, and Piperacillin + Tazobactum.
All the isolates showed a good sensitivity towards Nitrofurantoin
(82%). ESBL production was found to be 70.6% in Escherichia coli
and 29.4% in Klebsiella pneumonia. Susceptibility of ESBL
producers to Imipenem, Nitrofurantoin and Amikacin were found to
be 100%, 76%, and 75% respectively. Uropathogens are increasingly
showing resistance to many antibiotics making empiric management
of outpatient UTIs challenging. Ampicillin, Cotrimoxazole and
Ciprofloxacin should not be used in empiric treatment. Nitrofurantoin
could be used in lower urinary tract infection. Knowledge of
uropathogens and their antimicrobial susceptibility pattern in a
geographical region will help in appropriate and judicious antibiotic
usage in a health care setup.
Abstract: Radiative heat transfer in participating medium was
carried out using the finite volume method. The radiative transfer
equations are formulated for absorbing and anisotropically scattering
and emitting medium. The solution strategy is discussed and the
conditions for computational stability are conferred. The equations
have been solved for transient radiative medium and transient
radiation incorporated with transient conduction. Results have been
obtained for irradiation and corresponding heat fluxes for both the
cases. The solutions can be used to conclude incident energy and
surface heat flux. Transient solutions were obtained for a slab of heat
conducting in slab and by thermal radiation. The effect of heat
conduction during the transient phase is to partially equalize the
internal temperature distribution. The solution procedure provides
accurate temperature distributions in these regions. A finite volume
procedure with variable space and time increments is used to solve
the transient radiation equation. The medium in the enclosure
absorbs, emits, and anisotropically scatters radiative energy. The
incident radiations and the radiative heat fluxes are presented in
graphical forms. The phase function anisotropy plays a significant
role in the radiation heat transfer when the boundary condition is
non-symmetric.
Abstract: The latest years the number of immigrants at Greece
has increased dramatically. Their impact on the National Health
System (NHS) has not been yet thoroughly investigated. This paper
analyses the cost of immigrants to the NHS hospitals of the region of
Eastern Macedonia and Thrace. The data are collected from 2005 to
2011 from five different hospitals and are analysed using linear
mixed effects models in order to investigate the effects of nationality
and year on the cost of hospitalization and treatment. The results
show that generally the Greek nationality patients have a higher mean
cost of hospitalization compared to the immigrants and that there is
an increasing trend for the cost except for the year 2010.
Abstract: This work explores the inter-region investment
behaviors of Integrated Circuit (IC) design industry from Taiwan to
China using the amount of foreign direct investment (FDI). According
to the mutual dependence among different IC design industrial
locations, Lotka-Volterra model is utilized to explore the FDI
interactions between South and East China. Effects of inter-regional
collaborations on FDI flows into China are considered. The analysis
results show that FDIs into South China for IC design industry
significantly inspire the subsequent FDIs into East China, while FDIs
into East China for Taiwan’s IC design industry significantly hinder
the subsequent FDIs into South China. Because the supply chain along
IC industry includes upstream IC design, midstream manufacturing, as
well as downstream packing and testing enterprises, IC design industry
has to cooperate with IC manufacturing, packaging and testing
industries in the same area to form a strong IC industrial cluster.
Taiwan’s IC design industry implement the largest FDI amount into
East China and the second largest FDI amount into South China
among the four regions: North, East, Mid-West and South China. If IC
design houses undertake more FDIs in South China, those in East
China are urged to incrementally implement more FDIs into East
China to maintain the competitive advantages of the IC supply chain in
East China. On the other hand, as the FDIs in East China rise, the FDIs
in South China will successively decline since capitals have
concentrated in East China. In addition, this investigation proves that
the prediction of Lotka-Volterra model in FDI trends is accurate
because the industrial interactions between the two regions are
included. Finally, this work confirms that the FDI flows cannot reach a
stable equilibrium point, so the FDI inflows into East and South China
will expand in the future.
Abstract: Massive rock avalanches formed some of the largest landslide deposits on Earth and they represent one of the major geohazards in high-relief mountains. This paper interprets a very large sedimentary fan (the Sernio fan, Valtellina, Northern Italy), located 20 Km SW from Val Pola Rock avalanche (1987), as the deposit of a partial collapse of a Deep Seated Gravitational Slope Deformation (DSGSD), afterwards eroded and buried by debris flows. The proposed emplacement sequence has been reconstructed based on geomorphological, structural and mechanical evidences. The Sernio fan is actually considered anomalous with reference to the very high ratio between the fan area (≈ 4.5km2) and the basin area (≈ 3km2). The morphology of the fan area is characterised by steep slopes (dip ≈ 20%) and the fan apex is extended for 1.8 km inside the small catchment basin. This sedimentary fan was originated by a landslide that interested a part of a large deep-seated gravitational slope deformation, involving a wide area of about 55 km². The main controlling factor is tectonic and it is related to the proximity to regional fault systems and the consequent occurrence of fault weak rocks (GSI locally lower than 10 with compressive stress lower than 20MPa). Moreover, the fan deposit shows sedimentary evidences of recent debris flow events. The best current explanation of the Sernio fan involves an initial failure of some hundreds of Mm3. The run-out was quite limited because of the morphology of Valtellina’s valley floor, and the deposit filled the main valley forming a landslide dam, as confirmed by the lacustrine deposits detected upstream the fan. Nowadays the debris flow events represent the main hazard in the study area.
Abstract: Istanbul-Karakoy Port, field of this study, has lost its
former significance in time due to the transformation of urban
functions. Today, activities for regeneration of this region continue in
two forms and scales. First of these activities is the "planned
transformation projects," which also includes “Galataport project”,
and the second one is "spontaneous transformation," which consists
of individual interventions. Galataport project that based on the idea
of arranging the area specifically for tourists was prepared in 2005
and became a topic of tremendous public debate. On the other hand,
the "spontaneous transformation" that is observed in Karakoy District
starts in 2004 with the foundation of “Istanbul Modern Museum”
which allowed the cultural integration of old naval warehouses of the
port to the daily life. Following this adaptive reuse intervention, the
district started to accommodate numerous art galleries, studios, caféworkshops
and design stores. In this context, this paper first examines
regeneration studies in obsolete port regions, analyzes the planned
and ongoing socio-spatial transformations in the specific case of
Karakoy and performs a critical review of the sustainability of the
proposals on how to reinstate the district in the active life of Istanbul.
Abstract: Temperature effect on the performance of a photovoltaic module is one of the main concerns that face this renewable energy, especially in hot arid region, e.g. United Arab Emirates. Overheating of the PV modules reduces the open circuit voltage and the efficiency of the modules dramatically. In this work, water-cooling is developed to enhance the performance of PV modules. Different scenarios are tested under UAE weather conditions: front, back and double cooling. A spraying system is used for the front cooling whether a direct contact water system is used for the back cooling. The experimental results are compared to non-cooling module and the performance of the PV module is determined for different situations. The experimental results show that the front cooling is more effective than the back cooling and may decrease the temperature of the PV module significantly.
Abstract: The seriously damaged structures during earthquakes
show the need and importance of design of reinforced concrete
structures with high ductility. Reinforced concrete beam-column
joints have an important function in all structures. Under seismic
excitation, the beam column joint region is subjected to horizontal
and vertical shear forces whose magnitude is many times higher than
the adjacent beam and column. Strength and ductility of structures
depends mainly on proper detailing of the reinforcement in beamcolumn
joints and the old structures were found ductility deficient.
DSP materials are obtained by using high quantities of super
plasticizers and high volumes of micro silica. In the case of High
Performance Densified Small Particle Concrete (HPDSPC), since
concrete is dense even at the micro-structure level, tensile strain
would be much higher than that of the conventional SFRC, SIFCON
& SIMCON. This in turn will improve cracking behaviour, ductility
and energy absorption capacity of composites in addition to
durability. The fine fibers used in our mix are 0.3mm diameter and 10
mm which can be easily placed with high percentage. These fibers
easily transfer stresses and act as a composite concrete unit to take up
extremely high loads with high compressive strength. HPDSPC
placed in the beam column joints helps in safety of human life due to
prolonged failure.
Abstract: In this study, failure analysis of pipe system at a micro
hydroelectric power plant is investigated. Failure occurred at the pipe
system in the powerhouse during shut down operation of the water
flow by a valve. This locking had caused a sudden shock wave, also
called “Water-hammer effect”, resulting in noise and inside pressure
increase. After visual investigation of the effect of the shock wave on
the system, a circumference crack was observed at the pipe flange
weld region. To establish the reason for crack formation, calculations
of pressure and stress values at pipe, flange and welding seams were
carried out and concluded that safety factor was high (2.2), indicating
that no faulty design existed. By further analysis, pipe system and
hydroelectric power plant was examined. After observations it is
determined that the plant did not include a ventilation nozzle (air
trap), that prevents the system of sudden pressure increase inside the
pipes which is caused by water-hammer effect. Analyses were carried
out to identify the influence of water-hammer effect on inside
pressure increase and it was concluded that, according Jowkowsky’s
equation, shut down time is effective on inside pressure increase. The
valve closing time was uncertain but by a shut down time of even one
minute, inside pressure would increase by 7.6 bar (working pressure
was 34.6 bar). Detailed investigations were also carried out on the
assembly of the pipe-flange system by considering technical
drawings. It was concluded that the pipe-flange system was not
installed according to the instructions. Two of five weld seams were
not applied and one weld was carried out faulty. This incorrect and
inadequate weld seams resulted in; insufficient connection of the pipe
to the flange constituting a strong notch effect at weld seam regions,
increase in stress values and the decrease of strength and safety
factor.
Abstract: In some applications, such as image recognition or
compression, segmentation refers to the process of partitioning a
digital image into multiple segments. Image segmentation is typically
used to locate objects and boundaries (lines, curves, etc.) in images.
Image segmentation is to classify or cluster an image into several
parts (regions) according to the feature of image, for example, the
pixel value or the frequency response. More precisely, image
segmentation is the process of assigning a label to every pixel in an
image such that pixels with the same label share certain visual
characteristics. The result of image segmentation is a set of segments
that collectively cover the entire image, or a set of contours extracted
from the image. Several image segmentation algorithms were
proposed to segment an image before recognition or compression. Up
to now, many image segmentation algorithms exist and be
extensively applied in science and daily life. According to their
segmentation method, we can approximately categorize them into
region-based segmentation, data clustering, and edge-base
segmentation. In this paper, we give a study of several popular image
segmentation algorithms that are available.
Abstract: Regions with extreme climate conditions such as
Astana city require energy saving measures to increase energy
performance of buildings which are responsible for more than 40% of
total energy consumption. Identification of optimal building
geometry is one of key factors to be considered. Architectural form of
a building has impact on space heating and cooling energy use,
however the interrelationship between the geometry and resultant
energy use is not always readily apparent. This paper presents a
comparative case study of two prototypical buildings with compact
building shape to assess its impact on energy performance.
Abstract: Main purpose of this study is to identify the impact of
government expenditure on economic growth in Asian Countries.
Consequently, main objective is to analyze whether government
expenditure causes economic growth in Asian countries vice versa
and then scrutinizing long-run equilibrium relationship exists
between them. The study completely based on secondary data. The
methodology being quantitative that includes econometrical
techniques of cointegration, panel fixed effects model and granger
causality in the context of panel data of Asian countries; Singapore,
Malaysia, Thailand, South Korea, Japan, China, Sri Lanka, India and
Bhutan with 44 observations in each country, totaling to 396
observations from 1970 to 2013. The model used is the random
effects panel OLS model. As with the above methodology, the study
found the fascinating outcome. At first, empirical findings exhibit a
momentous positive impact of government expenditure on Gross
Domestic Production in Asian region. Secondly, government
expenditure and economic growth indicate a long-run relationship in
Asian countries. In conclusion, there is a unidirectional causality
from economic growth to government expenditure and government
expenditure to economic growth in Asian countries. Hence the study
is validated that it is in line with the Keynesian theory and Wagner’s
law as well. Consequently, it can be concluded that role of
government would play a vital role in economic growth of Asian
Countries. However; if government expenditure did not figure out
with the economy’s needs it might be considerably inspiration the
economy in a negative way so that society bears the costs.
Abstract: Although there has been a growing interest in the
hybrid free-space optical link and radio frequency FSO/RF
communication system, the current literature is limited to results
obtained in moderate or cold environment. In this paper, using a soft
switching approach, we investigate the effect of weather
inhomogeneities on the strength of turbulence hence the channel
refractive index under Qatar harsh environment and their influence
on the hybrid FSO/RF availability. In this approach, either FSO/RF
or simultaneous or none of them can be active. Based on soft
switching approach and a finite state Markov Chain (FSMC) process,
we model the channel fading for the two links and derive a
mathematical expression for the outage probability of the hybrid
system. Then, we evaluate the behavior of the hybrid FSO/RF under
hazy and harsh weather. Results show that the FSO/RF soft switching
renders the system outage probability less than that of each link
individually. A soft switching algorithm is being implemented on
FPGAs using Raptor code interfaced to the two terminals of a
1Gbps/100 Mbps FSO/RF hybrid system, the first being implemented
in the region. Experimental results are compared to the above
simulation results.
Abstract: The aim of the current work was to employ the finite
element method to model a slab, with a small hole across its width,
undergoing plastic plane strain deformation. The computational
model had, however, to be validated by comparing its results with
those obtained experimentally. Since they were in good agreement,
the finite element method can therefore be considered a reliable tool
that can help gain better understanding of the mechanism of ductile
failure in structural members having stress raisers. The finite element
software used was ANSYS, and the PLANE183 element was utilized.
It is a higher order 2-D, 8-node or 6-node element with quadratic
displacement behavior. A bilinear stress-strain relationship was used
to define the material properties, with constants similar to those of the
material used in the experimental study. The model was run for
several tensile loads in order to observe the progression of the plastic
deformation region, and the stress concentration factor was
determined in each case. The experimental study involved employing the visioplasticity
technique, where a circular mesh (each circle was 0.5 mm in
diameter, with 0.05 mm line thickness) was initially printed on the
side of an aluminum slab having a small hole across its width.
Tensile loading was then applied to produce a small increment of
plastic deformation. Circles in the plastic region became ellipses,
where the directions of the principal strains and stresses coincided
with the major and minor axes of the ellipses. Next, we were able to
determine the directions of the maximum and minimum shear
stresses at the center of each ellipse, and the slip-line field was then
constructed. We were then able to determine the stress at any point in
the plastic deformation zone, and hence the stress concentration
factor. The experimental results were found to be in good agreement
with the analytical ones.
Abstract: Information technology plays an irreplaceable role in
introducing and improving business process orientation in a
company. It enables implementation of the theoretical concept,
measurement of results achieved and undertaking corrective
measures aimed at improvements. Information technology is a key
concept in the development and implementation of the business
process management systems as it establishes a connection to
business operations. Both in the literature and practice, insurance
companies are often seen as highly process oriented due to the nature
of their business and focus on customers. They are also considered
leaders in using information technology for business process
management. The research conducted aimed to investigate whether
the perceived leadership status of insurance companies is well
deserved, i.e. to establish the level of process orientation and explore
the practice of information technology use in insurance companies in
the region. The main instrument for primary data collection within
this research was an electronic survey questionnaire sent to the
management of insurance companies in the Republic of Croatia,
Bosnia and Herzegovina, Slovenia, Serbia and Macedonia. The
conducted research has shown that insurance companies have a
satisfactory level of process orientation, but that there is also a huge
potential for improvement, especially in the segment of information
technology and its connection to business processes.
Abstract: Expansive soils are often encountered in many parts
of the world, especially in arid and semi-arid fields. Such kind of
soils, generally including active clay minerals in low water content,
enlarge in volume by absorbing the water through the surface and
cause a great harm to the light structures such as channel coating,
roads and airports. The expansive soils were encountered on the path
of Apa-Hotamış conveyance channel belonging to the State
Hydraulic Works in the region of Konya. In the research done in this
area, it is predicted that the soil has a swollen nature and the soil
should be filled with proper granular equipments by digging the
ground to 50-60 cm. In this study, for purpose of helping the other
research to be done in the same area, it is thought that instead of
replacing swollen soil with the granular soil, by stabilizing it with
polypropylene fiber and using it its original place decreases effect of
swelling percent, in this way the cost will be decreased. Therefore,
laboratory tests were conducted to study the effects of polypropylene
fiber on swelling characteristics of expansive soil. Test results
indicated that inclusion of fiber reduced swell percent of expansive
soil. As the fiber content increased, the unconfined compressive
strength was increased. Finally, it can be said that stabilization of
expansive soils with polypropylene fiber is an effective method.