Abstract: This paper explains about the voltage output for DC to
DC boost converter between open loop, PID controller and fuzzy
logic controller through Matlab Simulink. Simulink input voltage was
set at 12V and the voltage reference was set at 24V. The analysis on
the deviation of voltage resulted that the difference between reference
voltage setting and the output voltage is always lower. Comparison
between open loop, PID and FLC shows that, the open loop circuit
having a bit higher on the deviation of voltage. The PID circuit
boosts for FLC has a lesser deviation of voltage and proved that it is
such a better performance on control the deviation of voltage during
the boost mode.
Abstract: In this paper, we propose a new packing strategy to
find a free resource for run-time mapping of application tasks to
NoC-based Heterogeneous MPSoC. The proposed strategy minimizes
the task mapping time in addition to placing the communicating tasks
close to each other. To evaluate our approach, a comparative study is
carried out for a platform containing single task supported PEs.
Experiments show that our strategy provides better results when
compared to latest dynamic mapping strategies reported in the
literature.
Abstract: The bean (Phaseolus vulgaris L.) is one of the best
known of the legumes, and it has a long cultivation tradition in Italy.
The territory of “Subappennino Dauno” (southern Italy) is at around
700 m a.s.l. and is predominantly grown with cereals, olive trees and
grapevines. Ecotypes of white beans to eat dry (such as cannellini
beans) are also grown, which are sought for their palatability, high
digestibility, and ease of cooking. However, these are not easy to find
on the market due to their low production in relatively small areas
and on small family farms that use seeds handed down from
generation to generation. The introduction of these ecotypes in plain
areas of the Puglia region would provide an opportunity to promote
the diffusion of this type of bean. To investigate the adaptability of
these ecotypes in plain environments (Cerignola, in southern Italy) a
comparative trial was carried out between three ‘Monti Dauni’
ecotypes (E1, E2, E3) that are native to mountain areas and the
similar commercial variety, ‘Cannellini’. The data provide useful
information about the quantitative and qualitative characteristics of
these ecotypes when grown in lowland environments. Ecotype E3
provided the greatest bean production (2.34 t ha-1) compared to
‘Cannellini’ (1.28 t ha-1) and the other ecotypes (0.55 and 0.40 t ha-1,
for E1 and E2, respectively), due to its greater plant growth and the
larger size of the seed (and thickness, in particular). Finally, ecotype
E2 provided the greatest protein content (31.2%), although not
significantly different from the commercial cultivar ‘Cannellini’
(32.1%).
Abstract: Through this paper we present a method for automatic
generation of ontological model from any data source using Model
Driven Architecture (MDA), this generation is dedicated to the
cooperation of the knowledge engineering and software engineering.
Indeed, reverse engineering of a data source generates a software
model (schema of data) that will undergo transformations to generate
the ontological model. This method uses the meta-models to validate
software and ontological models.
Abstract: Curcuma longa L. (Zingiberaceae), commonly known
as turmeric, has a long history of traditional uses for culinary
purposes as a spice and a food colorant. The present study aimed to
document the ethnobotanical knowledge about Curcuma longa, and
to assess the variation in the herbalists’ experience in Northeastern
Algeria. Data were collected using semi-structured questionnaires
and direct interviews with 30 herbalists. Ethnobotanical indices,
including the fidelity level (FL%), the relative frequency citation
(RFC), and use value (UV) were determined by quantitative methods.
Diversity in the level of knowledge was analyzed using univariate,
non-parametric, and multivariate statistical methods. Three main
categories of uses were recorded for C. longa: for food, for medicine,
and for cosmetic purposes. As a medicine, turmeric was used for the
treatment of gastrointestinal, dermatological, and hepatic diseases.
Medicinal and food uses were correlated with both forms of
preparation (rhizome and powder). The age group did not influence
the use. Multivariate analyses showed a significant variation in
traditional knowledge, associated with the use value, origin, quality,
and efficacy of the drug. The findings suggested that the geographical
origin of C. longa affected the use in Algeria.
Abstract: The effective development of a geoscience education
and training program takes account of the rapidly changing
environment in the geoscience market, includes information about
resource-rich countries which have international education demands.
In this paper, we introduce the geoscience program run by the
International School for Geoscience Resources at the Korea Institute
of Geoscience and Mineral Resources (IS-Geo of KIGAM), and show
its remarkable performance. To further effective geoscience program
planning and operation, we present recommendations for strategic
management for customer-oriented operation with a more favorable
program format and advanced training aids. Above all, the IS-Geo of
KIGAM should continue improve through ‘plan-do-see-feedback’
activities based on the recommendations.
Abstract: The use of information and communication
technologies such as computers, mobile phones and the Internet is
becoming prevalent in today’s world; and it is facilitating access to a
vast amount of data, services and applications for the improvement of
people’s lives. However, this prevalence of ICTs is hampered by the
problem of low income levels in developing countries to the point
where people cannot timeously replace or repair their ICT devices
when damaged or lost; and this problem serves as a motivation for
this study whose aim is to examine the perceptions of teachers on the
reliability of cellphones when used for teaching and learning
purposes. The research objectives unfolding this aim are of two
types: Objectives on the selection and design of theories and models,
and objectives on the empirical testing of these theories and models.
The first type of objectives is achieved using content analysis in an
extensive literature survey: and the second type of objectives is
achieved through a survey of high school teachers from the ILembe
and UMgungundlovu districts in the KwaZulu-Natal province of
South Africa. Data collected from this questionnaire based survey is
analysed in SPSS using descriptive statistics and Pearson correlations
after checking the reliability and validity of the questionnaires. The
main hypothesis driving this study is that there is a relationship
between the demographics and the attribution identity of teachers on
one hand, and their perceptions on the reliability of cellphones on the
other hand, as suggested by existing literature; except that attribution
identities are considered in this study under three angles: intention,
knowledge and ability, and action. The results of this study confirm
that the perceptions of teachers on the reliability of cellphones for
teaching and learning are affected by the school location of these
teachers, and by their perceptions on learners’ cellphones usage
intentions and actual use.
Abstract: The handwriting is a physical demonstration of a
complex cognitive process learnt by man since his childhood. People
with disabilities or suffering from various neurological diseases are
facing so many difficulties resulting from problems located at the
muscle stimuli (EMG) or signals from the brain (EEG) and which
arise at the stage of writing. The handwriting velocity of the same
writer or different writers varies according to different criteria: age,
attitude, mood, writing surface, etc. Therefore, it is interesting to
reconstruct an experimental basis records taking, as primary
reference, the writing speed for different writers which would allow
studying the global system during handwriting process. This paper
deals with a new approach of the handwriting system modeling based
on the velocity criterion through the concepts of artificial neural
networks, precisely the Radial Basis Functions (RBF) neural
networks. The obtained simulation results show a satisfactory
agreement between responses of the developed neural model and the
experimental data for various letters and forms then the efficiency of
the proposed approaches.
Abstract: An investigation into the effect of countersunk depth,
plate thickness, countersunk angle and plate width on the stress
concentration around countersunk hole is carried out with the help of
finite element analysis. The variation of stress concentration with
respect to these parameters is studied for three types of loading viz.
uniformly distributed load, uniformly varying load and functionally
distributed load. The results of the finite element analysis are
interpreted and some conclusions are drawn. The distribution of
stress concentration around countersunk hole in isotropic plates
simply supported at all the edges is found similar and is independent
of loading. The maximum stress concentration also occurs at a
particular point irrespective of the loading conditions.
Abstract: Present study is aimed on the cutting process of circular
cross-section rods where the fracture is used to separate one rod
into two pieces. Incorporating the phenomenological ductile fracture
model into the explicit formulation of finite element method, the
process can be analyzed without the necessity of realizing too many
real experiments which could be expensive in case of repetitive
testing in different conditions. In the present paper, the steel AISI
1045 was examined and the tensile tests of smooth and notched
cylindrical bars were conducted together with biaxial testing of the
notched tube specimens to calibrate material constants of selected
phenomenological ductile fracture models. These were implemented
into the Abaqus/Explicit through user subroutine VUMAT and used
for cutting process simulation. As the calibration process is based
on variables which cannot be obtained directly from experiments,
numerical simulations of fracture tests are inevitable part of the
calibration. Finally, experiments regarding the cutting process were
carried out and predictive capability of selected fracture models is
discussed. Concluding remarks then make the summary of gained
experience both with the calibration and application of particular
ductile fracture criteria.
Abstract: This paper deals with the problem of automatic rule
generation for fuzzy systems design. The proposed approach is based
on hybrid artificial bee colony (ABC) optimization and weighted least
squares (LS) method and aims to find the structure and parameters of
fuzzy systems simultaneously. More precisely, two ABC based fuzzy
modeling strategies are presented and compared. The first strategy
uses global optimization to learn fuzzy models, the second one
hybridizes ABC and weighted least squares estimate method. The
performances of the proposed ABC and ABC-LS fuzzy modeling
strategies are evaluated on complex modeling problems and compared
to other advanced modeling methods.
Abstract: In the present work, the finite element formulation for
the investigation of the effects of a localized interfacial degeneration
on the dynamic behavior of the [90°/0°] laminated composite plate
employing the state-space technique is performed. The stiffness of
the laminate is determined by assembling the stiffnesses of subelements.
This includes an introduction of an interface layer adopting
the virtually zero-thickness formulation to model the interfacial
degeneration. Also, the kinematically consistent mass matrix and
proportional damping have been formulated to complete the free
vibration governing expression. To simulate the interfacial
degeneration of the laminate, the degenerated areas are defined from
the center propagating outwards in a localized manner. It is found
that the natural frequency, damped frequency and damping ratio of
the plate decreases as the degenerated area of the interface increases.
On the contrary, the loss factor increases correspondingly.
Abstract: The postharvest quality management of tomatoes is
important to limit the amount of losses that occur due to deterioration
between harvest and consumption. This study was undertaken to
investigate the effects of pre- and postharvest integrated agrotechnologies,
involving greenhouse microclimate and postharvest
storage conditions, on the postharvest quality attributes of four
tomato cultivars. Tomato fruit firmness, colour (hue angle (h°) and
L* value), pH and total soluble solids for the cultivars Bona,
Star 9037, Star 9009 and Zeal, grown in a fan-pad evaporativelycooled
and an open-ended naturally-ventilated tunnel, were harvested
at the mature-green stage. The tomatoes were stored for 28 days
under cold storage conditions, with a temperature of 13°C and RH of
85%, and under ambient air conditions, with a temperature of 23±
2°C and RH of 52± 4%. This study has provided information on the
effect of integrated pre-harvest and postharvest agro-technologies,
involving greenhouse microclimate and postharvest storage
environment on the postharvest quality attributes of four of the
tomato cultivars in South Africa. NVT-grown tomatoes retained
better textural qualities, but ripened faster by changing from green to
red faster, although these were reduced under cold storage conditions.
FPVT-grown tomatoes had lower firmness, but ripened slowly with
higher colour attributes. With cold storage conditions, the firmness of
FPVT-grown tomatoes was maintained. Cultivar Bona firmness and
colour qualities depreciated the fastest, but it had higher TSS content
and lower pH values. Star 9009 and Star 9037 presented better
quality, by retaining higher firmness and ripening slowly, but they
had the lowest TSS contents and high pH values, especially
Star 9037. Cold storage improved the firmness of tomato cultivars
with poor textural quality and faster colour changes.
Abstract: This paper is drawn from a wider study of the
management of gender, age and disability diversity in the banking
sector in the Kingdom of Saudi Arabia (KSA), which aims to develop
a framework for diversity management (DM) in this sector. The
paper focuses on the management of disability diversity. The purpose
of the paper is to assist in understanding disability DM in the banking
sector in KSA and to make suggestions for its enhancement. Hence, it
contributes to filling a research gap, as there is a dearth of literature
on disability DM, in KSA in general, and in the banking sector
specifically.
Discrimination against people with disabilities is a social issue that
has not been entirely overcome in any society. However, in KSA,
Islam informs almost every aspect of daily life including work, and
Islam is against discrimination. Hence, in KSA, there are regulations
to accommodate people with disabilities; however, employers are still
free not to hire job applicants with disabilities specifically because of
their condition. Indeed, disabled people are almost entirely absent
from the labour market.
There are 12 Saudi-owned or part-Saudi-owned banks in KSA and
two managers from each of these were interviewed, making a total of
24. The interviews aimed to investigate empirically the understanding
of managers in the banking sector in KSA of diversity management,
including disability DM, in the banking sector. The interview data
were analysed using thematic analysis. Two interviewees stated that
banks used the employment of people with disabilities to enhance
their corporate image, while five expressed the opinion that disabled
employees could contribute to the bank provided they did not have to
deal with customers face-to-face. Nine of the interviewees perceived
that disabled employees could be of value to the bank for their own
sake, not only in ‘behind the scenes’ roles. Another two interviewees
mentioned that employing disabled people could be part of the bank’s
community service programme and one thought it would be part of
the bank’s Saudisation efforts. The remaining five interviewees did
not know how disabled people could contribute to the bank.
The findings show that disability DM in the banking sector in
KSA is a relatively new concept, and is not yet well understood. In
the light of the findings, in order to achieve the purpose of the paper,
the following suggestions were made for the enhancement of
disability DM in the banking sector in KSA. A change in attitudes
towards disabled people is necessary. Such a change in the workplace
can only be achieved if a top-down approach is taken to the
integration of disabled people. Hence, it is suggested that
management and employees follow a course in disability awareness.
Further, a diversity officer in the HR department could enhance the
integration of disabled people into the banking workforce. It is also
suggested that greater government support is required through closely
monitored and enforced anti-discrimination legislation. Moreover,
flexible working arrangements such as part-time work would
facilitate the employment of disabled people and benefit other groups
of employees.
Abstract: In today’s world, the LED display has been used for
presenting visual information under various circumstances. Such
information is an important intermediary in the human information
processing. Researchers have been investigated diverse factors that
influence this process effectiveness. The letter size is undoubtedly
one major factor that has been tested and recommended by many
standards and guidelines. However, viewing information on the
display from direct perpendicular position is a typical assumption
whereas many actual events are required viewing from the angles.
This current research aims to study the effect of oblique viewing
angle and viewing distance on ability to recognize alphabet, number,
and English word. The total of ten participants was volunteered to our
3 x 4 x 4 within subject study. Independent variables include three
distance levels (2, 6, and 12 m), four oblique angles (0, 45, 60, 75
degree), and four target types (alphabet, number, short word, and
long word). Following the method of constant stimuli our study
suggests that the larger oblique angle, ranging from 0 to 75 degree
from the line of sight, results in significant higher legibility threshold
or larger font size required (p-value < 0.05). Viewing distance factor
also shows to have significant effect on the threshold (p-value
Abstract: GRF, Growth regulating factor, genes encode a novel
class of plant-specific transcription factors. The GRF proteins play a
role in the regulation of cell numbers in young and growing tissues
and may act as transcription activations in growth and development
of plants. Identification of GRF genes and their expression are
important in plants to performance of the growth and development of
various organs. In this study, to better understanding the structural
and functional differences of GRFs family, 45 GRF proteins
sequences in A. thaliana, Z. mays, O. sativa, B. napus, B. rapa, H.
vulgare and S. bicolor, have been collected and analyzed through
bioinformatics data mining. As a result, in secondary structure of
GRFs, the number of alpha helices was more than beta sheets and in
all of them QLQ domains were completely in the biggest alpha helix.
In all GRFs, QLQ and WRC domains were completely protected
except in AtGRF9. These proteins have no trans-membrane domain
and due to have nuclear localization signals act in nuclear and they
are component of unstable proteins in the test tube.
Abstract: The substantial similarity of fatigue mechanism in a
new test rig for rolling contact fatigue (RCF) has been investigated. A
new reduced-scale test rig is designed to perform controlled RCF
tests in wheel-rail materials. The fatigue mechanism of the rig is
evaluated in this study using a combined finite element-fatigue
prediction approach. The influences of loading conditions on fatigue
crack initiation have been studied. Furthermore, the effects of some
artificial defects (squat-shape) on fatigue lives are examined. To
simulate the vehicle-track interaction by means of the test rig, a threedimensional
finite element (FE) model is built up. The nonlinear
material behaviour of the rail steel is modelled in the contact
interface. The results of FE simulations are combined with the critical
plane concept to determine the material points with the greatest
possibility of fatigue failure. Based on the stress-strain responses, by
employing of previously postulated criteria for fatigue crack initiation
(plastic shakedown and ratchetting), fatigue life analysis is carried
out. The results are reported for various loading conditions and
different defect sizes. Afterward, the cyclic mechanism of the test rig
is evaluated from the operational viewpoint. The results of fatigue
life predictions are compared with the expected number of cycles of
the test rig by its cyclic nature. Finally, the estimative duration of the
experiments until fatigue crack initiation is roughly determined.
Abstract: Thanks to informational technologies development
every sphere of economics is becoming more and more datacentralized
as people are generating huge datasets containing
information on any aspect of their life. Applying research of such
data to human resources management allows getting scarce statistics
on labor market state including salary expectations and potential
employees’ typical career behavior, and this information can become
a reliable basis for management decisions.
The following article presents results of career behavior research
based on freely accessible resume data. Information used for study is
much wider than one usually uses in human resources surveys. That
is why there is enough data for statistically significant results even
for subgroups analysis.
Abstract: A single-phase closed thermosyphon has been
fabricated and experimented to utilize solar energy for water heating.
The working fluid of the closed thermosyphon is heated at the flatplate
collector and the hot water goes to the water tank due to density
gradient caused by temperature differences. This experimental work
was done using insulated water tank and insulated connecting pipe
between the tank and the flat-plate collector. From the collected data,
performance parameters such as instantaneous collector efficiency
and heat removal factor are calculated. In this study, the effects of
glazing were also observed. The water temperature rise and the
maximum instantaneous efficiency obtained from this experiment
with glazing using insulated water tank and insulated connecting pipe
are 17°C in a period of 5 hours and 60% respectively. Whereas the
water temperature rise and the maximum instantaneous efficiency
obtained from this experiment with glazing using non-insulated water
tank and non-insulated connecting pipe are 14°C in a period of 5
hours and 39% respectively.
Abstract: In the second decade of the XXI century the role of
tourism destination attractiveness is becoming increasingly important
for destination management. Competition in tourism market moves
from ordinary service quality to provision of unforgettable emotional
experience for tourists. The main purpose of the present study is to
identify the perception of the tourism destinations based on the
number of factors related to its tourist attractiveness.
The content analysis method was used to analyze the on-line
tourist feedback data immensely available in Social Media and in
travel related sites. The collected data made it possible to procure the
information which is necessary to understand the perceived
attractiveness of the destinations and key destination appeal factors
that are important for Russian leisure travelers.
Results of the present study demonstrate key attractiveness factors
or destination ‘properties’ that were unveiled as the most important
for Russian leisure tourists. The study targeted five main Spanish
tourism destinations that initially were determined by in-depth
interview with a number of Russian nationals who had visited Spain
at least once.
The research results can be useful for Spanish Tourism
Organization Representation office in Russia as well as for the other
national tourism organizations in order to promote their respective
destinations for Russian travelers focusing on main attractiveness
factors identified in this study.