Abstract: It has experimentally been proved that the
performance of compression ignition (C.I.) engine is spray
characteristics related. In modern diesel engine the spray formation
and the eventual combustion process are the vital processes that offer
more challenges towards enhancing the engine performance. In the
present work the numerical simulation has been carried out for
evaporating diesel sprays using Fluent software. For computational
fluid dynamics simulation “Meshing” is done using Gambit software
before transmitting it into Fluent. The simulation is carried out using
hot bomb conditions under varying chamber conditions such as gas
pressure, nozzle diameter and fuel injection pressure. For comparison
purpose, the numerical simulations the chamber conditions were kept
the same as that of the experimental data. At varying chamber
conditions the spray penetration rates are compared with the existing
experimental results.
Abstract: The prepreg process among the CFRP (Carbon Fiber
Reinforced Plastic) forming methods is the short term of
‘Pre-impregnation’, which is widely used for aerospace composites
that require a high quality property such as a fiber-reinforced woven
fabric, in which an epoxy hardening resin is impregnated the reality.
However, that this process requires continuous researches and
developments for its commercialization because the delamination
characteristically develops between the layers when a great weight is
loaded from outside to supplement such demerit, three lamination
methods among the prepreg lamination methods of CFRP were
designed to minimize the delamination between the layers due to
external impacts. Further, the newly designed methods and the
existing lamination methods were analyzed through a mechanical
characteristic test, Interlaminar Shear Strength test. The Interlaminar
Shear Strength test result confirmed that the newly proposed three
lamination methods, i.e. the Roll, Half and Zigzag laminations,
presented more excellent strengths compared to the conventional Ply
lamination. The interlaminar shear strength in the roll method with
relatively dense fiber distribution was approximately 1.75% higher
than that in the existing ply lamination method, and in the half method,
it was approximately 0.78% higher.
Abstract: In this paper, the electromagnetic shielding
characteristics of an up-to-date typical carbon filler material, carbon
fiber used with a metal mesh were investigated. Carbon fiber
12k-prepregs, where carbon fibers were impregnated with epoxy, were
laminated with wire meshes, vacuum bag-molded and hardened to
manufacture hybrid-type specimens, with which an electromagnetic
shield test was performed in accordance with ASTM D4935-10,
through which was known as the most excellent reproducibility is
obtainable among electromagnetic shield tests. In addition, glass fiber
prepregs whose electromagnetic shielding effect were known as
insignificant were laminated and formed with wire meshes to verify
the validity of the electromagnetic shield effect of wire meshes in
order to confirm the electromagnetic shielding effect of metal meshes
corresponding existing carbon fiber 12k-prepregs. By grafting carbon
fibers, on which studies are being actively underway in the
environmental aspects and electromagnetic shielding effect, with
hybrid-type wire meshes that were analysed through the tests, in this
study, the applicability and possibility are proposed.
Abstract: This study examines several critical dimensions of eservice
quality overlooked in the existing literature and proposes a
model and instrument framework for measuring customer perceived
e-service quality in the banking sector. The initial design was derived
from a pool of instrument dimensions and their items from the
existing literature review by content analysis. Based on focused
group discussion, nine dimensions were extracted. An exploratory
factor analysis approach was applied to data from a survey of 323
respondents. The instrument has been designed specifically for the
banking sector. Research data was collected from bank customers
who use electronic banking in a developing economy. A nine-factor
instrument has been proposed to measure the e-service quality. The
instrument has been checked for reliability. The validity and sample
place limited the applicability of the instrument across economies and
service categories. Future research must be conducted to check the
validity. This instrument can help bankers in developing economies
like India to measure the e-service quality and make improvements.
The present study offers a systematic procedure that provides insights
on to the conceptual and empirical comprehension of customer
perceived e-service quality and its constituents.
Abstract: Water flow management is one of the most important
parts of river engineering. Non-uniformity distribution of rainfall and
various flow demand with unreasonable flow management will be
caused destroyed of river ecosystem. Then, it is very serious to
determine ecosystem flow requirement. In this paper, Flow duration
curve indices method which has hydrological based was used to
evaluate environmental flow in Gharasou River, Ardabil, Iran. Using
flow duration curve, Q90 and Q95 for different return periods were
calculated. Their magnitude were determined as 1-day, 3-day, 7-day
and 30 day. According the second method, hydraulic alteration
indices often had low and medium range. In order to maintain river at
an acceptable ecological condition, minimum daily discharge of
index Q95 is 0.7 m3.s-1.
Abstract: Digital image correlation (DIC) is a contactless fullfield
displacement and strain reconstruction technique commonly
used in the field of experimental mechanics. Comparing with
physical measuring devices, such as strain gauges, which only
provide very restricted coverage and are expensive to deploy widely,
the DIC technique provides the result with full-field coverage and
relative high accuracy using an inexpensive and simple experimental
setup. It is very important to study the natural patterns effect on the
DIC technique because the preparation of the artificial patterns is
time consuming and hectic process. The objective of this research is
to study the effect of using images having natural pattern on the
performance of DIC. A systematical simulation method is used to
build simulated deformed images used in DIC. A parameter (subset
size) used in DIC can have an effect on the processing and accuracy
of DIC and even cause DIC to failure. Regarding to the picture
parameters (correlation coefficient), the higher similarity of two
subset can lead the DIC process to fail and make the result more
inaccurate. The pictures with good and bad quality for DIC methods
have been presented and more importantly, it is a systematic way to
evaluate the quality of the picture with natural patterns before they
install the measurement devices.
Abstract: Fructo-oligosaccharides (FOS) are produced from
sucrose by Aureobasidium pullulans in yields between 40-60%
(w/w). To increase the amount of FOS it is necessary to remove the
small, non-prebiotic sugars, present. Two methods for producing
high-purity FOS have been developed: the use of microorganisms
able to consume small saccharides; and the use of continuous
chromatography to separate sugars: simulated moving bed (SMB). It
is herein proposed the combination of both methods. The aim of this
study is to optimize the composition of the fermentative broth (in
terms of salts and sugars) that will be further purified by SMB. A
yield of 0.63 gFOS.gSucrose^-1 was obtained with A. pullulans using low
amounts of salts in the initial fermentative broth. By removing the
small sugars, Saccharomyces cerevisiae and Zymomonas mobilis
increased the percentage of FOS from around 56.0% to 83% (w/w) in
average, losing only 10% (w/w) of FOS during the recovery process.
Abstract: In this paper, Bayesian online inference in models of
data series are constructed by change-points algorithm, which
separated the observed time series into independent series and study
the change and variation of the regime of the data with related
statistical characteristics. variation of statistical characteristics of time
series data often represent separated phenomena in the some
dynamical system, like a change in state of brain dynamical reflected
in EEG signal data measurement or a change in important regime of
data in many dynamical system. In this paper, prediction algorithm
for studying change point location in some time series data is
simulated. It is verified that pattern of proposed distribution of data
has important factor on simpler and smother fluctuation of hazard
rate parameter and also for better identification of change point
locations. Finally, the conditions of how the time series distribution
effect on factors in this approach are explained and validated with
different time series databases for some dynamical system.
Abstract: Performance of different filtering approaches depends
on modeling of dynamical system and algorithm structure. For
modeling and smoothing the data the evaluation of posterior
distribution in different filtering approach should be chosen carefully.
In this paper different filtering approaches like filter KALMAN,
EKF, UKF, EKS and smoother RTS is simulated in some trajectory
tracking of path and accuracy and limitation of these approaches are
explained. Then probability of model with different filters is
compered and finally the effect of the noise variance to estimation is
described with simulations results.
Abstract: Background and aim: It has not been well studied
whether fentanyl-thiopental (FT) is effective and safe for PSA in
orthopedic procedures in Emergency Department (ED). The aim of
this trial was to evaluate the effectiveness of intravenous FT versus
fentanyl-midazolam (FM) in patients who suffered from shoulder
dislocation or distal radial fracture-dislocation.
Methods: In this randomized double-blinded study, Seventy-six
eligible patients were entered the study and randomly received
intravenous FT or FM. The success rate, onset of action and recovery
time, pain score, physicians’ satisfaction and adverse events were
assessed and recorded by treating emergency physicians. The
statistical analysis was intention to treat.
Results: The success rate after administrating loading dose in FT
group was significantly higher than FM group (71.7% vs. 48.9%,
p=0.04); however, the ultimate unsuccessful rate after 3 doses of
drugs in the FT group was higher than the FM group (3 to 1) but it
did not reach to significant level (p=0.61). Despite near equal onset
of action time in two study group (P=0.464), the recovery period in
patients receiving FT was markedly shorter than FM group
(P
Abstract: This paper presents an evolutionary algorithm for
solving multi-objective optimization problems-based artificial neural
network (ANN). The multi-objective evolutionary algorithm used in
this study is genetic algorithm while ANN used is radial basis
function network (RBFN). The proposed algorithm named memetic
elitist Pareto non-dominated sorting genetic algorithm-based RBFN
(MEPGAN). The proposed algorithm is implemented on medical
diseases problems. The experimental results indicate that the
proposed algorithm is viable, and provides an effective means to
design multi-objective RBFNs with good generalization capability
and compact network structure. This study shows that MEPGAN
generates RBFNs coming with an appropriate balance between
accuracy and simplicity, comparing to the other algorithms found in
literature.
Abstract: At certain depths during large diameter displacement
pile driving, rebound well over 0.25 inches was experienced,
followed by a small permanent-set during each hammer blow. High
pile rebound (HPR) soils may stop the pile driving and results in a
limited pile capacity. In some cases, rebound leads to pile damage,
delaying the construction project, and the requiring foundations
redesign. HPR was evaluated at seven Florida sites, during driving of
square precast, prestressed concrete piles driven into saturated, fine
silty to clayey sands and sandy clays. Pile Driving Analyzer (PDA)
deflection versus time data recorded during installation, was used to
develop correlations between cone penetrometer (CPT) pore-water
pressures, pile displacements and rebound. At five sites where piles
experienced excessive HPR with minimal set, the pore pressure
yielded very high positive values of greater than 20 tsf. However, at
the site where the pile rebounded, followed by an acceptable
permanent-set, the measured pore pressure ranged between 5 and 20
tsf. The pore pressure exhibited values of less than 5 tsf at the site
where no rebound was noticed. In summary, direct correlations
between CPTu pore pressure and rebound were produced, allowing
identification of soils that produce HPR.
Abstract: Chemotherapy and radiotherapy are one of the major
treatment modalities that play important role in the management of a
number of different cancers. This study for the first time evaluates the
toxicity of these treatment modalities and its impact on quality of life
of cancer patients in Pakistan. The study also for the first time
determines what cancer patients of different ages and cancer stages
believe would be an effective intervention to manage their
psychosocial needs and treatment induced toxicity. The article also
provides evidence based approach for the use of variety of
interventions to mange cancer treatment induced morbidity and
toxicity. In light of the present study and reviewed research data,
evidence based recommendations are also made for selection of
appropriate interventions to manage Pain, Nausea and Vomiting,
Anxiety and Depression, Fatigue and Overall QOL of cancer
survivors.
Abstract: Text mining techniques are generally applied for
classifying the text, finding fuzzy relations and structures in data
sets. This research provides plenty text mining capabilities. One
common application is text classification and event extraction,
which encompass deducing specific knowledge concerning incidents
referred to in texts. The main contribution of this paper is the
clarification of a concept graph generation mechanism, which is based
on a text classification and optimal fuzzy relationship extraction.
Furthermore, the work presented in this paper explains the application
of fuzzy relationship extraction and branch and bound (BB) method
to simplify the texts.
Abstract: The aim of this study was to design and simulate a
particular type of Asynchronous State Machine (ASM), namely a
‘traffic light controller’ (TLC), operated at a frequency of 0.5 Hz.
The design task involved two main stages: firstly, designing a 4-bit
binary counter using J-K flip flops as the timing signal and,
subsequently, attaining the digital logic by deploying ASM design
process. The TLC was designed such that it showed a sequence of
three different colours, i.e. red, yellow and green, corresponding to
set thresholds by deploying the least number of AND, OR and NOT
gates possible. The software Multisim was deployed to design such
circuit and simulate it for circuit troubleshooting in order for it to
display the output sequence of the three different colours on the
traffic light in the correct order. A clock signal, an asynchronous 4-
bit binary counter that was designed through the use of J-K flip flops
along with an ASM were used to complete this sequence, which was
programmed to be repeated indefinitely. Eventually, the circuit was
debugged and optimized, thus displaying the correct waveforms of
the three outputs through the logic analyser. However, hazards
occurred when the frequency was increased to 10 MHz. This was
attributed to delays in the feedback being too high.
Abstract: Assembly line balancing problem is aimed to divide
the tasks among the stations in assembly lines and optimize some
objectives. In assembly lines the workload on stations is different
from each other due to different tasks times and the difference in
workloads between stations can cause blockage or starvation in some
stations in assembly lines. Buffers are used to store the semi-finished
parts between the stations and can help to smooth the assembly
production. The assembly line balancing and buffer sizing problem
can affect the throughput of the assembly lines. Assembly line
balancing and buffer sizing problems have been studied separately in
literature and due to their collective contribution in throughput rate of
assembly lines, balancing and buffer sizing problem are desired to
study simultaneously and therefore they are considered concurrently
in current research. Current research is aimed to maximize
throughput, minimize total size of buffers in assembly line and
minimize workload variations in assembly line simultaneously. A
multi objective optimization objective is designed which can give
better Pareto solutions from the Pareto front and a simple example
problem is solved for assembly line balancing and buffer sizing
simultaneously. Current research is significant for assembly line
balancing research and it can be significant to introduce optimization
approaches which can optimize current multi objective problem in
future.
Abstract: Motion Tracking and Stereo Vision are complicated,
albeit well-understood problems in computer vision. Existing
softwares that combine the two approaches to perform stereo motion
tracking typically employ complicated and computationally expensive
procedures. The purpose of this study is to create a simple and
effective solution capable of combining the two approaches. The
study aims to explore a strategy to combine the two techniques
of two-dimensional motion tracking using Kalman Filter; and depth
detection of object using Stereo Vision. In conventional approaches
objects in the scene of interest are observed using a single camera.
However for Stereo Motion Tracking; the scene of interest is
observed using video feeds from two calibrated cameras. Using two
simultaneous measurements from the two cameras a calculation for
the depth of the object from the plane containing the cameras is made.
The approach attempts to capture the entire three-dimensional spatial
information of each object at the scene and represent it through a
software estimator object. In discrete intervals, the estimator tracks
object motion in the plane parallel to plane containing cameras and
updates the perpendicular distance value of the object from the plane
containing the cameras as depth. The ability to efficiently track
the motion of objects in three-dimensional space using a simplified
approach could prove to be an indispensable tool in a variety of
surveillance scenarios. The approach may find application from high
security surveillance scenes such as premises of bank vaults, prisons
or other detention facilities; to low cost applications in supermarkets
and car parking lots.
Abstract: An environmentally benign protocol for the one-pot,
three-component synthesis of Triazolo[1,2-a]indazole-1,3,8-trione
derivatives by condensation of dimedone, urazole and aromatic
aldehydes catalyzed by HClO4/SiO2 NPS as an ecofriendly catalyst
with high catalytic activity and reusability at 100ºC under solventfree
conditions is reported. The reaction proceeds to completion
within 20-30 min in 77-86% yield.
Abstract: Equal channel angular pressing (ECAP) of
commercial Al-Mg-Si alloy was conducted using two strain rates.
The ECAP processing was conducted at room temperature and at
250°C. Route A was adopted up to a total number of four passes in
the present work. Structural evolution of the aluminum alloy discs
was investigated before and after ECAP processing using optical
microscopy (OM). Following ECAP, simple compression tests and
Vicker’s hardness were performed. OM micrographs showed that, the
average grain size of the as-received Al-Mg-Si disc tends to be larger
than the size of the ECAP processed discs. Moreover, significant
difference in the grain morphologies of the as-received and processed
discs was observed. Intensity of deformation was observed via the
alignment of the Al-Mg-Si consolidated particles (grains) in the
direction of shear, which increased with increasing the number of
passes via ECAP. Increasing the number of passes up to 4 resulted in
increasing the grains aspect ratio up to ~5. It was found that the
pressing temperature has a significant influence on the
microstructure, Hv-values, and compressive strength of the processed
discs. Hardness measurements demonstrated that 1-pass resulted in
increase of Hv-value by 42% compared to that of the as-received
alloy. 4-passes of ECAP processing resulted in additional increase in
the Hv-value. A similar trend was observed for the yield and
compressive strength. Experimental data of the Hv-values
demonstrated that there is a lack of any significant dependence on the
processing strain rate.
Abstract: Risperidone (RISP) is an antipsychotic agent and has
low water solubility and nontargeted delivery results in numerous
side effects. Hence, an attempt was made to develop SLNs hydrogel
for intranasal delivery of RISP to achieve maximum bioavailability
and reduction of side effects. RISP loaded SLNs composed of 1.65%
(w/v) lipid mass were produced by high shear homogenization (HSH)
coupled ultrasound (US) method using glycerylmonostearate (GMS)
or Imwitor 900K (solid lipid). The particles were loaded with 0.2%
(w/v) of the RISP & surface-tailored with a 2.02% (w/v) non-ionic
surfactant Tween® 80. Optimization was done using 32 factorial
design using Design Expert® software. The prepared SLNs
dispersion incorporated into Polycarbophil AA1 hydrogel (0.5%
w/v). The final gel formulation was evaluated for entrapment
efficiency, particle size, rheological properties, X ray diffraction, in
vitro diffusion, ex vivo permeation using sheep nasal mucosa and
histopathological studies for nasocilliary toxicity. The entrapment
efficiency of optimized SLNs was found to be 76 ± 2%,
polydispersity index