Abstract: In this paper, self-starting block hybrid method of
order (5,5,5,5)T is proposed for the solution of the special second
order ordinary differential equations with associated initial or
boundary conditions. The continuous hybrid formulations enable us
to differentiate and evaluate at some grids and off – grid points to
obtain four discrete schemes, which were used in block form for
parallel or sequential solutions of the problems. The computational
burden and computer time wastage involved in the usual reduction of
second order problem into system of first order equations are avoided
by this approach. Furthermore, a stability analysis and efficiency of
the block method are tested on stiff ordinary differential equations,
and the results obtained compared favorably with the exact solution.
Abstract: In space during functioning, a satellite will be heated
up due to the behavior of its components such as power electronics.
In order to prevent problems in the satellite, this heat has to be
released in space thanks to the cooling system. This system consists
of a loop heat pipe (LHP), in which a fluid streams through an
evaporator and a condenser. In the evaporator, the fluid captures the
heat from the satellite and evaporates. Then it flows to the condenser
where it releases the heat and it condenses. In this project, the two
mains parts of a cooling system are studied: the evaporator and the
condenser. The study of the diphasic loop was done starting from
digital simulations carried out under Matlab and Femlab.
Abstract: Turbulence of the incoming wind field is of paramount
importance to the dynamic response of civil engineering structures. Hence reliable stochastic models of the turbulence should be available from which time series can be generated for dynamic response and
structural safety analysis. In the paper an empirical cross spectral
density function for the along-wind turbulence component over the wind field area is taken as the starting point. The spectrum is spatially
discretized in terms of a Hermitian cross-spectral density matrix for the turbulence state vector which turns out not to be positive
definite. Since the succeeding state space and ARMA modelling of
the turbulence rely on the positive definiteness of the cross-spectral
density matrix, the problem with the non-positive definiteness of such
matrices is at first addressed and suitable treatments regarding it are proposed. From the adjusted positive definite cross-spectral density
matrix a frequency response matrix is constructed which determines the turbulence vector as a linear filtration of Gaussian white noise.
Finally, an accurate state space modelling method is proposed which allows selection of an appropriate model order, and estimation of a state space model for the vector turbulence process incorporating its phase spectrum in one stage, and its results are compared with a conventional ARMA modelling method.
Abstract: Voice Over IP (VoIP) is a technology that could pass
the voice traffic and data packet form over an IP network. Network
can be used for intranet or Internet. Phone calls using VoIP has
advantages in terms of cheaper cost of PSTN phone to more than
half, because the cost is calculated by the cost of the global nature of
the Internet. Session Initiation Protocol (SIP) is a signaling protocol
at the application layer which serves to establish, modify, and
terminate a multimedia session involving one or more users. This SIP
signaling has SIP message in text form that is used for session
management by the SIP components, such as User Agent, Registrar,
Redirect Server, and Proxy Server. To build a SIP communication is
required SIP Express Router (SER) to be able to receive SIP
messages, for handling the basic functions of SIP messages.
Problems occur when the NAT through which affects the voice
communication will be blocked starting from the sound that is not
sent or one side of the sound are sent (half duplex). How that could
be used to penetrate NAT is to use a given mediaproxy random RTP
port to penetrate NAT.
Abstract: Success is a European project that will implement several clean transport offers in three European cities and evaluate the environmental impacts. The goal of these measures is to improve urban mobility or the displacement of residents inside cities. For e.g. park and ride, electric vehicles, hybrid bus and bike sharing etc. A list of 28 criteria and 60 measures has been established for evaluation of these transport projects. The evaluation criteria can be grouped into: Transport, environment, social, economic and fuel consumption. This article proposes a decision support system based that encapsulates a hybrid approach based on fuzzy logic, multicriteria analysis and belief theory for the evaluation of impacts of urban mobility solutions. A web-based tool called DeSSIA (Decision Support System for Impacts Assessment) has been developed that treats complex data. The tool has several functionalities starting from data integration (import of data), evaluation of projects and finishes by graphical display of results. The tool development is based on the concept of MVC (Model, View, and Controller). The MVC is a conception model adapted to the creation of software's which impose separation between data, their treatment and presentation. Effort is laid on the ergonomic aspects of the application. It has codes compatible with the latest norms (XHTML, CSS) and has been validated by W3C (World Wide Web Consortium). The main ergonomic aspect focuses on the usability of the application, ease of learning and adoption. By the usage of technologies such as AJAX (XML and Java Script asynchrones), the application is more rapid and convivial. The positive points of our approach are that it treats heterogeneous data (qualitative, quantitative) from various information sources (human experts, survey, sensors, model etc.).
Abstract: The excessive use of agricultural pesticides and the
resulting contamination of food and beds of rivers have been a
recurring problem nowadays. Some of these substances can cause
changes in endocrine balance and impair reproductive function of
human and animal population. In the present study, we evaluated the
possible effects of the fungicide cuprous copper oxide Sandoz® on
pregnant Wistar rats. They received a daily oral administration of 103
or 3.103 mg/kg of the fungicide from the 6th to the 15th day of
gestation. On day 21 of gestation, the maternal and fetal toxicity
parameters and indices were determined. The administration of
cuprous oxide (Copper Sandoz) in Wistar rats, the period of
organogenesis, revealed no evidence of maternal toxicity or embryo
at the studied doses.
Abstract: In this paper, a single period inventory model with resalable returns has been analyzed in an imprecise and uncertain mixed environment. Demand has been introduced as a fuzzy random variable. In this model, a single order is placed before the start of the selling season. The customer, for a full refund, may return purchased products within a certain time interval. Returned products are resalable, provided they arrive back before the end of the selling season and are found to be undamaged. Products remaining at the end of the season are salvaged. All demands not met directly are lost. The probabilities that a sold product is returned and that a returned product is resalable, both imprecise in a real situation, have been assumed to be fuzzy in nature.
Abstract: OLAP uses multidimensional structures, to provide
access to data for analysis. Traditionally, OLAP operations are more
focused on retrieving data from a single data mart. An exception is
the drill across operator. This, however, is restricted to retrieving
facts on common dimensions of the multiple data marts. Our concern
is to define further operations while retrieving data from multiple
data marts. Towards this, we have defined six operations which
coalesce data marts. While doing so we consider the common as well
as the non-common dimensions of the data marts.
Abstract: To coop with urbanization issues and the economic need for expansion, the city of Jakarta is planning to reclaim more land in the Jakarta Bay. However, the reclamation activities of some islands have barely started and already the developers are facing difficulties in finding sufficient quantities of sand as fill material. When addressing the problem of sand scarcity in the case of Jakarta where, an excess of waste production, an inadequate solid waste management system and a lack of dumping ground pose a major problem, it is hard not to think of the use of waste as alternative fill material. This paper analyses the possibilities of using waste in the land reclamation projects, considering the governmental, social, environmental and economic context of the city. The results identify types of waste that could be used, ways of using those types of waste and implementation conditions for the city of Jakarta.
Abstract: Operating a device at high power and high frequency
is a major problem because wall losses greatly reduce the efficiency
of the device. In the present communication, authors analytically
analyzed the dependence of ohmic/RF efficiency, the fraction of
output power with respect to the total power generated, of gyrotron
cavity structure on the conductivity of copper for the second
harmonic TE0,6 mode. This study shows a rapid fall in the RF
efficiency as the quality (conductivity) of copper degrades. Starting
with an RF efficiency near 40% at the conductivity of ideal copper
(5.8 x 107 S/m), the RF efficiency decreases (upto 8%) as the copper
quality degrades. Assuming conductivity half that of ideal copper the
RF efficiency as a function of diffractive quality factor, Qdiff, has
been studied. Here the RF efficiency decreases rapidly with
increasing diffractive Q. Ohmic wall losses as a function of
frequency for 460 GHz gyrotron cavity excited in TE0,6 mode has
also been analyzed. For 460 GHz cavity, the extracted power is
reduced to 32% of the generated power due to ohmic losses in the
walls of the cavity.
Abstract: Magnesium wastes are produced by many industrial activities. This waste problem is becoming a future problem for the world. Magnesium borates have many advantages such as; high corrosion resistance, heat resistance, high coefficient of elasticity and can also be used in the production of material against radiation. Addition, magnesium borates have great potential in sectors
including ceramic and detergents industry and superconducting materials.
In this study, using the starting materials of waste magnesium and H3BO3 the hydrothermal method was applied at a moderate
temperature of 70oC. Several mole ratios of waste magnesium to H3BO3 are selected as; 1:2, 1:4, 1:6, 1:8, 1:10. Reaction time was determined as 1 hour. After the synthesis, X-Ray Diffraction (XRD) and Fourier Transform Infrared Spectroscopy (FT-IR) techniques are applied to products. As a result the forms of mcallisterite “Mg2(B6O7(OH)6)2.9(H2O)”, admontite “MgO(B2O3)3.7(H2O)” and magnesium boron hydrate (MgO(B2O3)3.6(H2O)” are obtained.
Abstract: Urban planning, in particular on protected landscape
areas, demands an increasing role of public participation within the
frame of the efficiency of sustainable planning process. The
development of urban planning actions in Protected Landscape areas,
as Sintra-Cascais Natural Park, should perform a methodological
process that is structured over distinct sequential stages, providing
the development of a continuous, interactive, integrated and
participative planning. From the start of Malveira da Serra and Janes
Plan process, several public participation actions were promoted, in
order to involve the local agents, stakeholders and the population in
the decision of specific local key issues and define the appropriate
priorities within the goals and strategies previously settled. As a
result, public participation encouraged an innovative process that
guarantees the efficiency of sustainable urban planning and promotes
a sustainable new way of living in community.
Abstract: The aim of this paper is to introduce the concepts of τ1τ2-regular generalized star star closed sets , τ1τ2-regular generalized star star open sets and study their basic properties in bitopological spaces.
Abstract: ZnO nanostructure were synthesized via microwave
method using zinc acetate as starting material, guanidinium as
structure directing agents, and water as solvent.. This work
investigates the photodegradation of azo dyes using the ZnO Flowerlike
in aqueous solutions. As synthesized ZnO samples were
characterized using X-Ray powder diffraction (XRD), scanning
electron microscopy (SEM), and FTIR spectroscopy.In this work
photodecolorization of congored azo dye under UV irradiation by
nano ZnO was studied.
Abstract: The occurrence and removal of trace organic
contaminants in the aquatic environment has become a focus of
environmental concern. For the selective removal of carbamazepine
from loaded waters molecularly imprinted polymers (MIPs) were
synthesized with carbamazepine as template. Parameters varied were
the type of monomer, crosslinker, and porogen, the ratio of starting
materials, and the synthesis temperature. Best results were obtained
with a template to crosslinker ratio of 1:20, toluene as porogen, and
methacrylic acid (MAA) as monomer. MIPs were then capable to
recover carbamazepine by 93% from a 10-5 M landfill leachate
solution containing also caffeine and salicylic acid. By comparison,
carbamazepine recoveries of 75% were achieved using a nonimprinted
polymer (NIP) synthesized under the same conditions, but
without template. In landfill leachate containing solutions
carbamazepine was adsorbed by 93-96% compared with an uptake of
73% by activated carbon. The best solvent for desorption was
acetonitrile, with which the amount of solvent necessary and dilution
with water was tested. Selected MIPs were tested for their reusability
and showed good results for at least five cycles. Adsorption
isotherms were prepared with carbamazepine solutions in the
concentration range of 0.01 M to 5*10-6 M. The heterogeneity index
showed a more homogenous binding site distribution.
Abstract: This paper addresses the fundamental requirements for
starting an online business. It covers the process of ideation,
conceptualization, formulation, and implementation of new venture
ideas on the Web. Using Facebook as an illustrative example, we learn
how to turn an idea into a successful electronic business and to execute
a business plan with IT skills, management expertise, a good
entrepreneurial attitude, and an understanding of Internet culture. The
personality traits and characteristics of a successful e-commerce
entrepreneur are discussed with reference to Facebook-s founder,
Mark Zuckerberg. Facebook is a social and e-commerce success. It
provides a trusted environment of which participants can conduct
business with social experience. People are able to discuss products
before, during the after the sale within the Facebook environment. The
paper also highlights the challenges and opportunities for e-commerce
entrepreneurial startups to go public and of entering the China market.
Abstract: In this treatise we will study the capability of static
compensator for reactive power to stabilize sheen voltage with motor
loading on power networks system. We also explain the structure and main function of STATCOM and the method to control it using STATCOM transformer current to simultaneously predict after
telling about the necessity of FACTS tools to compensate in power networks. Then we study topology and controlling system to stabilize
voltage during start of inductive motor. The outcome of stimulat by MATLAB software supports presented controlling idea and
system in the treatise.
Abstract: Stipples are desired for pattern fillings and
transparency effects. In contrast, some graphics standards, including
OpenGL ES 1.1 and 2.0, omitted this feature. We represent details of
providing line stipples and polygon stipples, through combining
texture mapping and alpha blending functions. We start from the
OpenGL-specified stipple-related API functions. The details of
mathematical transformations are explained to get the correct texture
coordinates. Then, the overall algorithm is represented, and its
implementation results are followed. We accomplished both of line
and polygon stipples, and verified its result with conformance test
routines.
Abstract: In this study, the effect of mechanical activation on the synthesis of Fe3Al/Al2O3 nanocomposite has been investigated by using mechanochemical method. For this purpose, Aluminum powder and hematite as precursors, with stoichiometric ratio, have been utilized and other effective parameters in milling process were kept constant. Phase formation analysis, crystallite size measurement and lattice strain were studied by X-ray diffraction (XRD) by using Williamson-Hall method as well as microstructure and morphology were explored by Scanning electron microscopy (SEM). Also, Energy-dispersive X-ray spectroscopy (EDX) analysis was used in order to probe the particle distribution. The results showed that after 30-hour milling, the reaction was started, combustibly done and completed.
Abstract: The purpose of this paper is to examine the financing
practices of SMEs in Libya in two different phases of business life
cycle: start-up and matured stages. Moreover, SMEs- accessing bank
loan issues is also identified. The study was conducted by taking into
account the aspect of demand. The findings are based on a sample of
76 SMEs in Libya through the adoption of questionnaires. The results
have pinpointed several things- evidently, SMEs use informal
financing sources which prefer personal savings; SME owners are
willing to apply for bank loan, that the most pressing problem has
been identified, not to apply bank loan is loan with interest (religion
factor).