Abstract: This paper presents an analytical approach for
evaluating distribution system reliability indices in the presence of
distributed generation. Modeling distributed generation and
evaluation of distribution system reliability indices using the
frequency duration technique. Using model implements and case
studies are discussed. Results showed that location of DG and its
effect in distribution reliability indices. In this respect, impact of DG
on distribution system is investigated using the IEEE Roy Billinton
test system (RBTS2) included feeder 1. Therefore, it will help to the
distribution system planners in the DG resource placement.
Abstract: High temperature Fischer-Tropsch synthesis process
use fixed fluidized bed as a reactor. In order to understand the flow
behavior in the fluidized bed better, the research of how the radial
velocity affects the entire flow field is necessary. Laser Doppler
Velocimetry (LDV) was used to study the radial velocity distribution
along the diameter direction of the cross-section of the particle in a
fixed fluidized bed. The velocity in the cross-section is fluctuating
within a small range. The direction of the speed is a random
phenomenon. In addition to r/R is 1, the axial velocity are more than 6
times of the radial velocity, the radial velocity has little impact on the
axial velocity in a fixed fluidized bed.
Abstract: A new approach has been developed to estimate the
load share and distribution of worm gear drives, and to calculate the
instantaneous tooth meshing stiffness. In the approach, the worm gear
drive was modelled as a series of spur gear slices, and each slice was
analyzed separately using the well-established formulae of spur gear
loading and stresses. By combining the results obtained for all slices,
the entire envolute worm gear set loading and stressing was obtained. The geometric modelling method presented allows tooth elastic
deformation and tooth root stresses of worm gear drives under
different load conditions to be investigated. Based on the slicing
method introduced in this study, the instantaneous meshing stiffness
and load share are obtained. In comparison with existing methods,
this approach has both good analysis accuracy and less computing
time.
Abstract: Carefully scheduling the operations of pumps can be
resulted to significant energy savings. Schedules can be defined
either implicit, in terms of other elements of the network such as tank
levels, or explicit by specifying the time during which each pump is
on/off. In this study, two new explicit representations based on timecontrolled
triggers were analyzed, where the maximum number of
pump switches was established beforehand, and the schedule may
contain fewer switches than the maximum. The optimal operation of
pumping stations was determined using a Jumping Particle Swarm
Optimization (JPSO) algorithm to achieve the minimum energy cost.
The model integrates JPSO optimizer and EPANET hydraulic
network solver. The optimal pump operation schedule of VanZyl
water distribution system was determined using the proposed model
and compared with those from Genetic and Ant Colony algorithms.
The results indicate that the proposed model utilizing the JPSO
algorithm is a versatile management model for the operation of realworld
water distribution system.
Abstract: Oxygen Reduction Reaction (ORR) performance of
iron and nitrogen co-doped porous carbon nanoparticles (Fe-NPC)
with various physical and (electro) chemical properties have been
investigated. Fe-NPC nanoparticles are synthesized via a facile
soft-templating procedure by using Iron (III) chloride hexa-hydrate as
iron precursor and aminophenol-formaldehyde resin as both carbon
and nitrogen precursor. Fe-NPC nanoparticles shows high surface area
(443.83 m2g-1), high pore volume (0.52 m3g-1), narrow mesopore size
distribution (ca. 3.8 nm), high conductivity (IG/ID=1.04), high kinetic
limiting current (11.71 mAcm-2) and more positive onset potential
(-0.106 V) compared to metal-free NPC nanoparticles (-0.295V)
which make it high efficient ORR metal-free catalysts in alkaline
solution. This study may pave the way of feasibly designing iron and
nitrogen containing carbon materials (Fe-N-C) for highly efficient
oxygen reduction electro-catalysis.
Abstract: There are a number of Distributed Generations (DGs)
installed in microgrid, which may have diverse path and direction of
power flow or fault current. The overcurrent protection scheme for the
traditional radial type distribution system will no longer meet the
needs of microgrid protection. Integrating the Intelligent Electronic
Device (IED) and a Supervisory Control and Data Acquisition
(SCADA) with IEC 61850 communication protocol, the paper
proposes a Microgrid Protection Management System (MPMS) to
protect power system from the fault. In the proposed method, the
MPMS performs logic programming of each IED to coordinate their
tripping sequence. The GOOSE message defined in IEC 61850 is used
as the transmission information medium among IEDs. Moreover, to
cope with the difference in fault current of microgrid between
grid-connected mode and islanded mode, the proposed MPMS applies
the group setting feature of IED to protect system and robust
adaptability. Once the microgrid topology varies, the MPMS will
recalculate the fault current and update the group setting of IED.
Provided there is a fault, IEDs will isolate the fault at once. Finally, the
Matlab/Simulink and Elipse Power Studio software are used to
simulate and demonstrate the feasibility of the proposed method.
Abstract: This paper is aimed to study combustion characteristics
of low NOx burner using petroleum cokes as fuel. The petroleum coke,
which is produced through the oil refining process, is an attractive fuel
in terms of its high heating value and low price. But petroleum coke is
a challenging fuel because of its low volatile content, high sulfur and
nitrogen content, which give rise to undesirable emission
characteristics and low ignitability. Therefore, the research and
development regarding the petroleum coke burner is needed for
applying this industrial system. In this study, combustion and emission
characteristics of petroleum cokes burner are experimentally
investigated in an industrial steam boiler. The low NOx burner is
designed to control fuel and air mixing to achieve staged combustion,
which, in turn reduces both flame temperature and oxygen. Air
distribution ratio of triple staged air is optimized experimentally. The
result showed that NOx concentration is lowest when overfire air is
used, and the burner function at a fuel rich condition. That is, the
burner is operated at the equivalence ratio of 1.67 and overall
equivalence ratio including overfire air is kept 0.87.
Abstract: In recent decades, probabilistic constrained optimal
control problems have attracted much attention in many research
fields. Although probabilistic constraints are generally intractable
in an optimization problem, several tractable methods haven been
proposed to handle probabilistic constraints. In most methods,
probabilistic constraints are reduced to deterministic constraints
that are tractable in an optimization problem. However, there is a
gap between the transformed deterministic constraints in case of
known and unknown probability distribution. This paper examines
the conservativeness of probabilistic constrained optimization method
for unknown probability distribution. The objective of this paper is
to provide a quantitative assessment of the conservatism for tractable
constraints in probabilistic constrained optimization with unknown
probability distribution.
Abstract: Leishmaniasis is the collective name for a number of
diseases caused by protozoan flagellates of the genus Leishmania,
which is transmitted by Phlebotomine sandfly, the disease has diverse
clinical manifestations and found in many areas of the world,
particularly in Africa, Latin America, South and Central Asia, the
Mediterranean basin and the Middle East. This study was done to
assess primary health care physicians’ knowledge (PHP) and attitude
about leishmaniasis and to assess awareness of local inhabitants
about the disease and its vector in four areas in west Alexandria,
Egypt. It is a cross sectional survey that was conducted in four PHC
units in west Alexandria. All physicians currently working in these
units during the study period were invited to participate in the study;
only 20 PHP completed the questionnaire. 60 local inhabitants were
selected randomly from the four areas of the study, 15 from each
area; Data was collected through two different specially designed
questionnaires. Results showed that 11 (55%) percent of the
physicians had satisfactory knowledge; they answered more than 9
(60%) questions out of a total 14 questions about leishmaniasis and
sandfly. On the other hand when attitude of the primary health care
physicians about leishmaniasis was measured, results showed that 17
(85%) had good attitude and 3 (15%) had poor attitude. The second
questionnaire showed that the awareness of local inhabitants about
leishmaniasis and sandfly as a vector of the disease is poor and needs
to be corrected. (90%) of the interviewed inhabitants had not heard
about leishmaniasis, Only 3 (5%) of them said they know sandfly and
its role in transmission of leishmaniasis. Thus we conclude that
knowledge and attitudes of physicians are acceptable. However, there
is, room for improvement and could be done through formal training
courses and distribution of guidelines. In addition to raising the
awareness of primary health care physicians about the importance of
early detection and notification of cases of leishmaniasis, health
education for raising awareness of the public regarding the vector and
the disease is necessary because related studies have demonstrated
that for inhabitants to take enough protective measures against the
vector, they should perceive that it is responsible for causing a
disease.
Abstract: This paper presents a novel algorithm for modeling
photovoltaic based distributed generators for the purpose of optimal
planning of distribution networks. The proposed algorithm utilizes
sequential Monte Carlo method in order to accurately consider the
stochastic nature of photovoltaic based distributed generators. The
proposed algorithm is implemented in MATLAB environment and
the results obtained are presented and discussed.
Abstract: The aim of the current work was to employ the finite
element method to model a slab, with a small hole across its width,
undergoing plastic plane strain deformation. The computational
model had, however, to be validated by comparing its results with
those obtained experimentally. Since they were in good agreement,
the finite element method can therefore be considered a reliable tool
that can help gain better understanding of the mechanism of ductile
failure in structural members having stress raisers. The finite element
software used was ANSYS, and the PLANE183 element was utilized.
It is a higher order 2-D, 8-node or 6-node element with quadratic
displacement behavior. A bilinear stress-strain relationship was used
to define the material properties, with constants similar to those of the
material used in the experimental study. The model was run for
several tensile loads in order to observe the progression of the plastic
deformation region, and the stress concentration factor was
determined in each case. The experimental study involved employing the visioplasticity
technique, where a circular mesh (each circle was 0.5 mm in
diameter, with 0.05 mm line thickness) was initially printed on the
side of an aluminum slab having a small hole across its width.
Tensile loading was then applied to produce a small increment of
plastic deformation. Circles in the plastic region became ellipses,
where the directions of the principal strains and stresses coincided
with the major and minor axes of the ellipses. Next, we were able to
determine the directions of the maximum and minimum shear
stresses at the center of each ellipse, and the slip-line field was then
constructed. We were then able to determine the stress at any point in
the plastic deformation zone, and hence the stress concentration
factor. The experimental results were found to be in good agreement
with the analytical ones.
Abstract: Twin steel plates-concrete composite shear walls are
composed of a pair of steel plate layers and a concrete layer
sandwiched between them, which have the characteristics of both
reinforced concrete shear walls and steel plate shear walls. Twin steel
plates-composite shear walls contain very high ultimsate bearing
capacity and ductility, which have great potential to be applied in the
super high-rise buildings and special structures. In this paper, we
analyzed the basic characteristics and stress mechanism of the twin
steel plates-composite shear walls. Specifically, we analyzed the
effects of the steel plate thickness, wall thickness and concrete
strength on the bearing capacity of the twin steel plates-composite
shear walls. The analysis results indicate that: (1) the initial shear
stiffness and ultimate shear-carrying capacity is not significantly
affected by the thickness of concrete wall but by the class of concrete,
(2) both factors significantly impact the shear distribution of the
shear walls in ultimate shear-carrying capacity. The technique of twin
steel plates-composite shear walls has been successfully applied in
the construction of an 88-meter Huge Statue of Buddha located in
Hunan Province, China. The analysis results and engineering
experiences showed that the twin steel plates-composite shear walls
have great potential for future research and applications.
Abstract: Photovoltaic (PV) power generation systems, mainly
small scale, are rapidly being deployed in Jordan. The impact of these
systems on the grid has not been studied or analyzed. These systems
can cause many technical problems such as reverse power flows and
voltage rises in distribution feeders, and real and reactive power
transients that affect the operation of the transmission system. To
fully understand and address these problems, extensive research,
simulation, and case studies are required. To this end, this paper
studies the cloud shadow effect on the power generation of a ground
mounted PV system installed at the test field of the Renewable
Energy Center at the Applied Science University.
Abstract: In this study, electric field distribution analyses for
three pylon models are carried out by a Finite Element Method
(FEM) based software. Analyses are performed in both stationary and
time domains to observe instantaneous values along with the
effective ones. Considering the results of the study, different line
geometries is considerably affecting the magnitude and distribution
of electric field although the line voltages are the same. Furthermore,
it is observed that maximum values of instantaneous electric field
obtained in time domain analysis are quite higher than the effective
ones in stationary mode. In consequence, electric field distribution
analyses should be individually made for each different line model
and the limit exposure values or distances to residential buildings
should be defined according to the results obtained.
Abstract: Facility location is a complex real-world problem
which needs a strategic management decision. This paper provides a
general review on studies, efforts and developments in Facility
Location Problems which are classical optimization problems having
a wide-spread applications in various areas such as transportation,
distribution, production, supply chain decisions and
telecommunication. Our goal is not to review all variants of different
studies in FLPs or to describe very detailed computational techniques
and solution approaches, but rather to provide a broad overview of
major location problems that have been studied, indicating how they
are formulated and what are proposed by researchers to tackle the
problem. A brief, elucidative table based on a grouping according to
“General Problem Type” and “Methods Proposed” used in the studies
is also presented at the end of the work.
Abstract: Below-knee amputees commonly experience
asymmetrical gait patterns. It is generally believed that ischemia is
related to the formation of pressure sores due to uneven distribution
of forces. Micro-vascular responses can reveal local malnutrition.
Changes in local skin blood supply under various external loading
conditions have been studied for a number of years. Radionuclide
clearance, photo-plethysmography, trans-cutaneous oxygen tension
along with other studies showed that the blood supply would be
influenced by the epidermal forces, and the rate and the amount of
blood supply would decrease with increased epidermal loads being
shear forces or normal forces. Several cases of socket designs were
investigated using Finite Element Model (FEM) and Design of
Experiment (DOE) to increase flexibility and minimize the pressure
at the limb/socket interface using ultra high molecular weight
polyethylene (UHMWPE) and polyamide 6 (PA6) or Duraform. The
pressure reliefs at designated areas where reducing thickness is
involved are seen to be critical in determination of amputees’ comfort
and are very important to clinical applications. Implementing a hole
between the Patellar Tendon (PT) and Distal Tibia (DT) would
decrease stiffness and increase prosthesis range of motion where
flexibility is needed. In addition, displacement and prosthetic energy
storage increased without compromising mechanical efficiency and
prosthetic design integrity.
Abstract: Sewer deposits have been identified as a major cause
of dysfunctions in combined sewer systems regarding sewer
management, which induces different negative consequents resulting
in poor hydraulic conveyance, environmental damages as well as
worker’s health. In order to overcome the problematics of
sedimentation, flushing has been considered as the most operative
and cost-effective way to minimize the sediments impacts and
prevent such challenges. Flushing, by prompting turbulent wave
effects, can modify the bed form depending on the hydraulic
properties and geometrical characteristics of the conduit. So far, the
dynamics of the bed-load during high-flow events in combined sewer
systems as a complex environment is not well understood, mostly due
to lack of measuring devices capable to work in the “hostile” in
combined sewer system correctly. In this regards, a one-episode
flushing issue from an opening gate valve with weir function was
carried out in a trunk sewer in Paris to understand its cleansing
efficiency on the sediments (thickness: 0-30 cm). During more than
1h of flushing within 5 m distance in downstream of this flushing
device, a maximum flowrate and a maximum level of water have
been recorded at 5 m in downstream of the gate as 4.1 m3/s and 2.1
m respectively. This paper is aimed to evaluate the efficiency of this
type of gate for around 1.1 km (from the point -50 m to +1050 m in
downstream from the gate) by (i) determining bed grain-size
distribution and sediments evolution through the sewer channel, as
well as their organic matter content, and (ii) identifying sections that
exhibit more changes in their texture after the flush. For the first one,
two series of sampling were taken from the sewer length and then
analyzed in laboratory, one before flushing and second after, at same
points among the sewer channel. Hence, a non-intrusive sampling
instrument has undertaken to extract the sediments smaller than the
fine gravels. The comparison between sediments texture after the
flush operation and the initial state, revealed the most modified zones
by the flush effect, regarding the sewer invert slope and hydraulic
parameters in the zone up to 400 m from the gate. At this distance,
despite the increase of sediment grain-size rages, D50 (median grainsize)
varies between 0.6 mm and 1.1 mm compared to 0.8 mm and 10
mm before and after flushing, respectively. Overall, regarding the
sewer channel invert slope, results indicate that grains smaller than
sands (< 2 mm) are more transported to downstream along about 400
m from the gate: in average 69% before against 38% after the flush
with more dispersion of grain-sizes distributions. Furthermore, high
effect of the channel bed irregularities on the bed material evolution
has been observed after the flush.
Abstract: The objective of this paper is to evaluate the effects of
soil-structure interaction (SSI) on the modal characteristics and on
the dynamic response of current structures. The objective is on the
overall behaviour of a real structure of five storeys reinforced
concrete (R/C) building typically encountered in Algeria. Sensitivity
studies are undertaken in order to study the effects of frequency
content of the input motion, frequency of the soil-structure system,
rigidity and depth of the soil layer on the dynamic response of such
structures. This investigation indicated that the rigidity of the soil
layer is the predominant factor in soil-structure interaction and its
increases would definitely reduce the deformation in the R/C
structure. On the other hand, increasing the period of the underlying
soil will cause an increase in the lateral displacements at story levels
and create irregularity in the distribution of story shears. Possible
resonance between the frequency content of the input motion and soil
could also play an important role in increasing the structural
response.
Abstract: The influence of physicochemical water quality
parameters on the abundance and diversity of caddisfly larvae was
studied in seven sampling stations in Mae Tao and Mae Ku
watersheds, Mae Sot District, Tak Province, northern Thailand. The
streams: MK2 and MK8 as reference site, and impacted streams
(MT1-MT5) were sampled bi-monthly during July 2011 to May
2012. A total of 4,584 individual of caddisfly larvae belonging to 10
family and 17 genera were found. The larvae of family
Hydropsychidae were the most abundance, followed by
Philopotamidae, Odontoceridae, and Leptoceridae, respectively. The
genus Cheumatopsyche, Hydropsyche, and Chimarra were the most
abundance genera in this study. Results of CCA ordination showed
the total dissolved solids, sulfate, water temperature, dissolved
oxygen and pH were the most important physicochemical factors to
affect distribution of caddisflies communities. Changes in the
caddisfly fauna may indicate changes in physicochemical factors
owing to agricultural pollution, urbanization, or other human
activities. Results revealed that the order Trichoptera, identified to
species or genus, can be potentially used to assess environmental
water quality status in freshwater ecosystems.
Abstract: Efficient use of energy, the increase in demand of
energy and also with the reduction of natural energy sources, has
improved its importance in recent years. Most of the losses in the
system from electricity produced until the point of consumption is
mostly composed by the energy distribution system. In this study,
analysis of the resulting loss in power distribution transformer and
distribution power cable is realized which are most of the losses in
the distribution system. Transformer losses in the real distribution
system are analyzed by CYME Power Engineering Software
program. These losses are disclosed for different voltage levels and
different loading conditions.