Abstract: A sliding door system is used in commercial vehicles
and passenger cars to allow a larger unobstructed access to the
interior for loading and unloading. The movement of a sliding door
on vehicle body is ensured by mechanisms and tracks having special
cross-section which is manufactured by roll forming and stretch
bending process. There are three tracks and three mechanisms which
are called upper, central and lower on a sliding door system. There
are static requirements as strength on different directions, rigidity for
mechanisms, door drop off, door sag; dynamic requirements as high
energy slam opening-closing and durability requirement to validate
these products. In addition, there is a kinematic requirement to find
out force values from door handle during manual operating. In this
study, finite element analysis and physical test results which are
realized for sliding door systems will be shared comparatively.
Abstract: In Automotive Industry, sliding door systems that are
also used as body closures are safety members. Extreme product tests
are realized to prevent failures in design process, but these tests
realized experimentally result in high costs. Finite element analysis is
an effective tool used for design process. These analyses are used
before production of prototype for validation of design according to
customer requirement. In result of this, substantial amount of time
and cost is saved. Finite element model is created for geometries that are designed in
3D CAD programs. Different element types as bar, shell and solid,
can be used for creating mesh model. Cheaper model can be created
by selection of element type, but combination of element type that
was used in model, number and geometry of element and degrees of
freedom affects the analysis result. Sliding door system is a good
example which used these methods for this study. Structural analysis
was realized for sliding door mechanism by using FE models. As
well, physical tests that have same boundary conditions with FE
models were realized. Comparison study for these element types,
were done regarding test and analyses results then optimum
combination was achieved.
Abstract: Damaturu is the capital of Yobe State in northeastern
Nigeria where civic amenities and facilities are not adequate even
after 24 years of its existence. The volatile security and political
situations are most significant causes for the same. The basic facility
for the citizens in terms of drinking water and electricity are not
available. For the drinking water, they have to rely on personal
boreholes or the filtered borehole waters available in packaged
sachets in market. The present study is concerned with environmental
impact of indiscriminate disposal of drinking synthetic polythene
water sachets in Damaturu. The sachet water is popularly called as
“pure water”, but its purity is questionable. Increased production and
consumption of sachet water has led to indiscriminate dumping and
disposal of empty sachets leading to serious environmental threat.
The evidence of this is seen for sachets littering the streets and the
drainages blocked by ‘blocks’ of water sachet waste. Sachet water
gained much popularity in Nigeria because the product is convenient
for use, affordable and economically viable. The present study aims
to find out the solution to this environmental problem. The fieldbased
study has found some significant factors that cause
environmental and socio economic effect due to this. Some
recommendations have been made based on research findings
regarding sustainable waste management, recycling and re-use of the
non-biodegradable products in society.
Abstract: E-retailing is the sale of goods online that takes place
over the Internet. The Internet has shrunk the entire World. World eretailing
is growing at an exponential rate in the Americas, Europe
and Asia. However, e-retailing costs require expensive investment,
such as hardware, software, and security systems. Cloud computing
technology is internet-based computing for the management and
delivery of applications and services. Cloud-based e-retailing
application models allow enterprises to lower their costs with their
effective implementation of e-retailing activities. In this paper, we
describe the concept of cloud computing and present the architecture
of cloud computing, combining the features of e-retailing. In
addition, we propose a strategy for implementing cloud computing
with e-retailing. Finally, we explain the benefits from the
architecture.
Abstract: In this study, failure analysis of pipe system at a micro
hydroelectric power plant is investigated. Failure occurred at the pipe
system in the powerhouse during shut down operation of the water
flow by a valve. This locking had caused a sudden shock wave, also
called “Water-hammer effect”, resulting in noise and inside pressure
increase. After visual investigation of the effect of the shock wave on
the system, a circumference crack was observed at the pipe flange
weld region. To establish the reason for crack formation, calculations
of pressure and stress values at pipe, flange and welding seams were
carried out and concluded that safety factor was high (2.2), indicating
that no faulty design existed. By further analysis, pipe system and
hydroelectric power plant was examined. After observations it is
determined that the plant did not include a ventilation nozzle (air
trap), that prevents the system of sudden pressure increase inside the
pipes which is caused by water-hammer effect. Analyses were carried
out to identify the influence of water-hammer effect on inside
pressure increase and it was concluded that, according Jowkowsky’s
equation, shut down time is effective on inside pressure increase. The
valve closing time was uncertain but by a shut down time of even one
minute, inside pressure would increase by 7.6 bar (working pressure
was 34.6 bar). Detailed investigations were also carried out on the
assembly of the pipe-flange system by considering technical
drawings. It was concluded that the pipe-flange system was not
installed according to the instructions. Two of five weld seams were
not applied and one weld was carried out faulty. This incorrect and
inadequate weld seams resulted in; insufficient connection of the pipe
to the flange constituting a strong notch effect at weld seam regions,
increase in stress values and the decrease of strength and safety
factor.
Abstract: Nitrification is essential to biological processes
designed to remove ammonia and/or total nitrogen. It removes excess
nitrogenous compound in wastewater which could be very toxic to
the aquatic fauna or cause serious imbalance of such aquatic
ecosystem. Efficient nitrification is linked to an in-depth knowledge
of the structure and dynamics of the nitrifying community structure
within the wastewater treatment systems. In this study, molecular
technique was employed for characterizing the microbial structure of
activated sludge [ammonia oxidizing bacteria (AOB) and nitrite
oxidizing bacteria (NOB)] in a municipal wastewater treatment with
intention of linking it to the plant efficiency. PCR based phylogenetic
analysis was also carried out. The average operating and
environmental parameters as well as specific nitrification rate of plant
was investigated during the study. During the investigation the average temperature was 23±1.5oC.
Other operational parameters such as mixed liquor suspended solids
and chemical oxygen demand inversely correlated with ammonia
removal. The dissolved oxygen level in the plant was constantly
lower than the optimum (between 0.24 and 1.267 mg/l) during this
study. The plant was treating wastewater with influent ammonia
concentration of 31.69 and 24.47 mg/L. The influent flow rates
(ML/Day) was 96.81 during period. The dominant nitrifiers include:
Nitrosomonas spp. Nitrobacter spp. and Nitrospira spp. The AOB
had correlation with nitrification efficiency and temperature. This
study shows that the specific ammonia oxidizing rate and the specific
nitrate formation rates can serve as good indicator of the plant overall
nitrification performance.
Abstract: This paper discusses the general methods to saturation
in the steady-state, two axis (d & q) frame models of synchronous
machines. In particular, the important role of the magnetic coupling
between the d-q axes (cross-magnetizing phenomenon), is
demonstrated. For that purpose, distinct methods of saturation
modeling of dumper synchronous machine with cross-saturation are
identified, and detailed models synthesis in d-q axes. A number of
models are given in the final developed form. The procedure and the
novel models are verified by a critical application to prove the
validity of the method and the equivalence between all developed
models is reported. Advantages of some of the models over the
existing ones and their applicability are discussed.
Abstract: There are a number of Distributed Generations (DGs)
installed in microgrid, which may have diverse path and direction of
power flow or fault current. The overcurrent protection scheme for the
traditional radial type distribution system will no longer meet the
needs of microgrid protection. Integrating the Intelligent Electronic
Device (IED) and a Supervisory Control and Data Acquisition
(SCADA) with IEC 61850 communication protocol, the paper
proposes a Microgrid Protection Management System (MPMS) to
protect power system from the fault. In the proposed method, the
MPMS performs logic programming of each IED to coordinate their
tripping sequence. The GOOSE message defined in IEC 61850 is used
as the transmission information medium among IEDs. Moreover, to
cope with the difference in fault current of microgrid between
grid-connected mode and islanded mode, the proposed MPMS applies
the group setting feature of IED to protect system and robust
adaptability. Once the microgrid topology varies, the MPMS will
recalculate the fault current and update the group setting of IED.
Provided there is a fault, IEDs will isolate the fault at once. Finally, the
Matlab/Simulink and Elipse Power Studio software are used to
simulate and demonstrate the feasibility of the proposed method.
Abstract: This paper addresses minimizing the makespan of the
distributed permutation flow shop scheduling problem. In this
problem, there are several parallel identical factories or flowshops
each with series of similar machines. Each job should be allocated to
one of the factories and all of the operations of the jobs should be
performed in the allocated factory. This problem has recently gained
attention and due to NP-Hard nature of the problem, metaheuristic
algorithms have been proposed to tackle it. Majority of the proposed
algorithms require large computational time which is the main
drawback. In this study, a general variable neighborhood search
algorithm (GVNS) is proposed where several time-saving schemes
have been incorporated into it. Also, the GVNS uses the sophisticated
method to change the shaking procedure or perturbation depending
on the progress of the incumbent solution to prevent stagnation of the
search. The performance of the proposed algorithm is compared to
the state-of-the-art algorithms based on standard benchmark
instances.
Abstract: Sweden has succeeded to maintain a high level of
growth and development and has managed to sustain highly ranked
position among the world’s developed countries. In this regard,
Swedish universities are playing a vital role in supporting innovation
and entrepreneurship at all levels and developing Swedish knowledge
economy. This paper is aiming to draw on the experiences of two leading
Swedish universities, addressing their transformation approach to
create entrepreneurial universities and fulfilling their objectives in the
era of knowledge economy. The objectives of the paper include: 1) Introducing the Swedish
higher education and its characteristics. 2) Examining the
infrastructure elements for innovation and Entrepreneurship at two of
the Swedish entrepreneurial universities. 3) Addressing the key
aspects of support systems in the initiatives of both Chalmers and
Gothenburg universities to support innovation and advance
entrepreneurial practices. The paper will contribute to two discourses: 1) Examining the
relationship between support systems for innovation and
entrepreneurship and the Universities’ policies and practices. 2)
Lessons for University leaders to assist the development and
implementation of effective innovation and entrepreneurship policies
and practices.
Abstract: Hollow section for bridge columns has some
advantages. However, current seismic design codes do not provide
design regulations for hollow bridge piers. There have been many
experimental studied for hollow reinforced concrete piers in the world.
But, Study for hollow section for bridge piers in Korea has been begun
with approximately 2000s. There has been conducted experimental
study for hollow piers of flexural controlled sections by Yeungnam
University, Sung kyunkwan University, Korea Expressway
Corporation in 2009. This study concluded that flexural controlled
sections for hollow piers showed the similar behavior to solid sections.
And there have been conducted experimental study for hollow piers of
compression controlled sections by Yeungnam University, Korea
Institute of Construction Technology in 2012. This study concluded
that compression controlled sections for hollow piers showed
compression fracture of concrete in inside wall face. Samsung
Construction & Trading Corporation has been conducted study with
Yeungnam University for reduce the quantity of reinforcement details
about hollow piers. Reduce the quantity of reinforcement details are
triangular cross tie. This study concluded that triangular reinforcement
details showed the similar behavior as compared with existing
reinforcement details.
Abstract: This study aims to increase understanding of the
transition of business models in servitization. The significance of
service in all business has increased dramatically during the past
decades. Service-dominant logic (SDL) describes this change in the
economy and questions the goods-dominant logic on which business
has primarily been based in the past. A business model canvas is one
of the most cited and used tools in defining end developing business
models. The starting point of this paper lies in the notion that the
traditional business model canvas is inherently goods-oriented and
best suits for product-based business. However, the basic differences
between goods and services necessitate changes in business model
representations when proceeding in servitization. Therefore, new
knowledge is needed on how the conception of business model and
the business model canvas as its representation should be altered in
servitized firms in order to better serve business developers and interfirm
co-creation. That is to say, compared to products, services are
intangible and they are co-produced between the supplier and the
customer. Value is always co-created in interaction between a
supplier and a customer, and customer experience primarily depends
on how well the interaction succeeds between the actors. The role of
service experience is even stronger in service business compared to
product business, as services are co-produced with the customer. This paper provides business model developers with a service
business model canvas, which takes into account the intangible,
interactive, and relational nature of service. The study employs a
design science approach that contributes to theory development via
design artifacts. This study utilizes qualitative data gathered in
workshops with ten companies from various industries. In particular,
key differences between Goods-dominant logic (GDL) and SDLbased
business models are identified when an industrial firm
proceeds in servitization. As the result of the study, an updated version of the business
model canvas is provided based on service-dominant logic. The
service business model canvas ensures a stronger customer focus and
includes aspects salient for services, such as interaction between
companies, service co-production, and customer experience. It can be
used for the analysis and development of a current service business
model of a company or for designing a new business model. It
facilitates customer-focused new service design and service
development. It aids in the identification of development needs, and
facilitates the creation of a common view of the business model.
Therefore, the service business model canvas can be regarded as a
boundary object, which facilitates the creation of a common
understanding of the business model between several actors involved.
The study contributes to the business model and service business
development disciplines by providing a managerial tool for
practitioners in service development. It also provides research insight
into how servitization challenges companies’ business models.
Abstract: Space Vector Pulse Width Modulation is popular for
variable frequency drives. The method has several advantages over
carried based PWM and is computation intensive. The
implementation of SVPWM for multilevel inverter requires special
attention and at the same time consumes considerable resources. Due
to faster processing power and reduced over all computational
burden, FPGAs are being investigated as an alternative for other
controllers. In this paper, a space vector PWM algorithm is
implemented using FPGA which requires less computational area and
is modular in structure. The algorithm is verified experimentally for
Neutral Point Clamped inverter using FPGA development board
xc3s5000-4fg900.
Abstract: Elliptic curve discrete logarithm problem(ECDLP) is
one of problems on which the security of pairing-based cryptography
is based. This paper considers Pollard’s rho method to evaluate
the security of ECDLP on Barreto-Naehrig(BN) curve that is an
efficient pairing-friendly curve. Some techniques are proposed to
make the rho method efficient. Especially, the group structure on
BN curve, distinguished point method, and Montgomery trick are
well-known techniques. This paper applies these techniques and
shows its optimization. According to the experimental results for
which a large-scale parallel system with MySQL is applied, 94-bit
ECDLP was solved about 28 hours by parallelizing 71 computers.
Abstract: When high strength reinforced concrete is exposed to
high temperature due to a fire, deteriorations occur such as loss in
strength and elastic modulus, cracking and spalling of the concrete.
Therefore, it is important to understand risk of structural safety in
building structures by studying structural behaviors and rehabilitation
of fire damaged high strength concrete structures. This paper aims at
investigating rehabilitation effect on fire damaged high strength
concrete beams using experimental and analytical methods. In the
experiments, flexural specimens with high strength concrete are
exposed to high temperatures according to ISO 834 standard time
temperature curve. From four-point loading test, results show that
maximum loads of the rehabilitated beams are similar to or higher than
those of the non-fire damaged RC beam. In addition, structural
analyses are performed using ABAQUS 6.10-3 with same conditions
as experiments to provide accurate predictions on structural and
mechanical behaviors of rehabilitated RC beams. The parameters are
the fire cover thickness and strengths of repairing mortar. Analytical
results show good rehabilitation effects, when the results predicted
from the rehabilitated models are compared to structural behaviors of
the non-damaged RC beams. In this study, fire damaged high strength concrete beams are
rehabilitated using polymeric cement mortar. The predictions from the
finite element (FE) models show good agreements with the
experimental results and the modeling approaches can be used to
investigate applicability of various rehabilitation methods for further
study.
Abstract: Present study was aimed to develop a discharge
measuring device for irrigation and laboratory channels. Experiments
were conducted on sharp edged constricted flow meters having four
types of width constrictions namely 2:1, 1.5:1, 1:1 and 90o in the
direction of flow. These devices were made of MS sheets and
installed separately in a rectangular flume. All these four devices
were tested under free and submerged flow conditions. Eight
different discharges varying from 2 lit/sec to 30 lit/sec were passed
through each device. In total around 500 observations of upstream
and downstream depths were taken in the present work. For each
discharge, free submerged and critical submergence under different
flow conditions were noted and plotted. Once the upstream and
downstream depths of flow over any of the device are known, the
discharge can be easily calculated with the help of the curves
developed for free and submerged flow conditions. The device
having contraction 2:1 is the most efficient one as it allows maximum
critical submergence.
Abstract: This paper is aimed to study combustion characteristics
of low NOx burner using petroleum cokes as fuel. The petroleum coke,
which is produced through the oil refining process, is an attractive fuel
in terms of its high heating value and low price. But petroleum coke is
a challenging fuel because of its low volatile content, high sulfur and
nitrogen content, which give rise to undesirable emission
characteristics and low ignitability. Therefore, the research and
development regarding the petroleum coke burner is needed for
applying this industrial system. In this study, combustion and emission
characteristics of petroleum cokes burner are experimentally
investigated in an industrial steam boiler. The low NOx burner is
designed to control fuel and air mixing to achieve staged combustion,
which, in turn reduces both flame temperature and oxygen. Air
distribution ratio of triple staged air is optimized experimentally. The
result showed that NOx concentration is lowest when overfire air is
used, and the burner function at a fuel rich condition. That is, the
burner is operated at the equivalence ratio of 1.67 and overall
equivalence ratio including overfire air is kept 0.87.
Abstract: Two normal populations with different means and same
variance are considered, where the variance is known. The population
with the smaller sample mean is selected. Various estimators are
constructed for the mean of the selected normal population. Finally,
they are compared with respect to the bias and MSE risks by
the mehod of Monte-Carlo simulation and their performances are
analysed with the help of graphs.
Abstract: This study presents a hybrid metaheuristic algorithm
to obtain optimum designs for steel space buildings. The optimum
design problem of three-dimensional steel frames is mathematically
formulated according to provisions of LRFD-AISC (Load and
Resistance factor design of American Institute of Steel Construction).
Design constraints such as the strength requirements of structural
members, the displacement limitations, the inter-story drift and the
other structural constraints are derived from LRFD-AISC
specification. In this study, a hybrid algorithm by using teachinglearning
based optimization (TLBO) and harmony search (HS)
algorithms is employed to solve the stated optimum design problem.
These algorithms are two of the recent additions to metaheuristic
techniques of numerical optimization and have been an efficient tool
for solving discrete programming problems. Using these two
algorithms in collaboration creates a more powerful tool and
mitigates each other’s weaknesses. To demonstrate the powerful
performance of presented hybrid algorithm, the optimum design of a
large scale steel building is presented and the results are compared to
the previously obtained results available in the literature.
Abstract: This study was to explore and utilize the fresh rind of
mangosteen Index Colour 5 as an upcoming raw material for the
production of natural dyes. Rind from the fresh mangosteen Index
Colour 5 was utilized to extract the dyes. The established extracts
were experimented on silk fabrics via three types of mordanting and
dyeing procedures; pre-mordanting, simultaneous mordanting and
post-mordanting. As a result, the applications of the freeze-drying
methodology and mechanizable equipment have helped to produce
excellent range of natural colours. Silk fabric treated simultaneously
with mordanting and dyeing with extract dye Index Colour 5
produced a brilliant shade of the red colour and the colour from this
index is also discovered sensitive to light and washing during the
fastness tests. The preliminary evaluation and instrumentation
analysis allowed us to examine whether the application of different
mordanting and dyeing procedures with the same extract samples and
concentrations affected the colours and shades of the fabric samples.