Abstract: By enhancing the applicatıon of grounds for
establishment and due to the lack of appropriate sites, engineers
attempt to seek out a new method to reduce the weakness of soils. İn
aspect of economic situation, various ways have been used to
decrease the weak grounds. Because of the rapid development of
infrastructural facilities, spreading the construction operation is an
obligation. Furthermore, in various sites with the really bad soil
situation, engineers have considered obvious problems. One of the
most essential ways for developing the weak soils is stone column.
Obviously, the method was introduced in France in 1830 to improve
a native soil initially. Stone columns have an expanding range of
usage in different rough foundation sites all over the world to
increase the bearing capacity, to reduce the whole and differential
settlements, to enhance the rate of consolidation, to stabilize slopes
stability of embankments and to increase the liquefaction resistance
as well. A recent procedure called installing vertical nails along the
round stone columns in order to make better the performance of
considered columns is offered. Moreover, thanks to the enhancing the
nail diameter, number and embedment nail depth, the positive points
of vertical circumferential nails increases. Based on the result of this
study, load caring capacity will be develop with enhancing the length
and the power of reinforcements in vertical encasement stone column
(CESC). In this study, the main purpose is comparing two methods of
stone columns (installed a nail surrounding the stone columns and
using geogrid on clay) for enhancing the bearing capacity, decreasing
the whole and various settlements.
Abstract: Consumers are demanding novel beverages that are
healthier, convenient and have appealing consumer acceptance. The
objectives of this study were to investigate the effects of adding grape
polyphenols and the influence of presenting health claims on the
sensory acceptability of wines. Fresh red sorrel calyces were
fermented into wines. The total soluble solids of the pectinase-treated
sorrel puree were from 4°Brix to 23.8°Brix. Polyphenol in the form
of grape pomace extract was added to sorrel wines (w/v) in specified
levels to give 0. 25. 50 and 75 ppm. A focus group comprising of 12
panelists was use to select the level of polyphenol to be added to
sorrel wines for sensory preference The sensory attributed of the
wines which were evaluated were colour, clarity, aroma, flavor,
mouth-feel, sweetness, astringency and overall preference. The sorrel
wine which was most preferred from focus group evaluation was
presented for hedonic rating. In the first stage of hedonic testing, the
sorrel wine was served chilled at 7°C for 24 h prior to sensory
evaluation. Each panelist was provided with a questionnaire and was
asked to rate the wines on colour, aroma, flavor, mouth-feel,
sweetness, astringency and overall acceptability using a 9-point
hedonic scale. In the second stage of hedonic testing, the panelist
were instructed to read a health abstract on the health benefits of
polyphenolic compounds and again to rate sorrel wine with added 25
ppm polyphenol. Paired t-test was used for the analysis of the
influence of presenting health information on polyphenols on hedonic
scoring of sorrel wines. Focus groups found that the addition of
polyphenol addition had no significant effect on sensory color and
aroma but affected clarity and flavor. A 25 ppm wine was liked
moderately in overall acceptability. The presentation of information
on the health benefit of polyphenols in sorrel wines to panelists had
no significant influence on the sensory acceptance of wine. More
than half of panelists would drink this wine now and then. This wine
had color L 19.86±0.68, chroma 2.10±0.12, hue° 16.90 ±3.10 and
alcohol content of 13.0%. The sorrel wine was liked moderately in
overall acceptability with the added polyphenols.
Abstract: This work is on decision tree-based classification for
the disbursement of scholarship. Tree-based data mining
classification technique is used in other to determine the generic rule
to be used to disburse the scholarship. The system based on the
defined rules from the tree is able to determine the class (status) to
which an applicant shall belong whether Granted or Not Granted. The
applicants that fall to the class of granted denote a successful
acquirement of scholarship while those in not granted class are
unsuccessful in the scheme. An algorithm that can be used to classify
the applicants based on the rules from tree-based classification was
also developed. The tree-based classification is adopted because of its
efficiency, effectiveness, and easy to comprehend features. The
system was tested with the data of National Information Technology
Development Agency (NITDA) Abuja, a Parastatal of Federal
Ministry of Communication Technology that is mandated to develop
and regulate information technology in Nigeria. The system was
found working according to the specification. It is therefore
recommended for all scholarship disbursement organizations.
Abstract: Computer aided diagnosis systems provide vital
opinion to radiologists in the detection of early signs of breast cancer
from mammogram images. Architectural distortions, masses and
microcalcifications are the major abnormalities. In this paper, a
computer aided diagnosis system has been proposed for
distinguishing abnormal mammograms with architectural distortion
from normal mammogram. Four types of texture features GLCM
texture, GLRLM texture, fractal texture and spectral texture features
for the regions of suspicion are extracted. Support vector machine
has been used as classifier in this study. The proposed system yielded
an overall sensitivity of 96.47% and an accuracy of 96% for
mammogram images collected from digital database for screening
mammography database.
Abstract: Batch production plants provide a wide range of
scheduling problems. In pharmaceutical industries a batch process
is usually described by a recipe, consisting of an ordering of tasks
to produce the desired product. In this research work we focused
on pharmaceutical production processes requiring the culture of
a microorganism population (i.e. bacteria, yeasts or antibiotics).
Several sources of uncertainty may influence the yield of the culture
processes, including (i) low performance and quality of the cultured
microorganism population or (ii) microbial contamination. For
these reasons, robustness is a valuable property for the considered
application context. In particular, a robust schedule will not collapse
immediately when a cell of microorganisms has to be thrown away
due to a microbial contamination. Indeed, a robust schedule should
change locally in small proportions and the overall performance
measure (i.e. makespan, lateness) should change a little if at all.
In this research work we formulated a constraint programming
optimization (COP) model for the robust planning of antibiotics
production. We developed a discrete-time model with a multi-criteria
objective, ordering the different criteria and performing a
lexicographic optimization. A feasible solution of the proposed
COP model is a schedule of a given set of tasks onto available
resources. The schedule has to satisfy tasks precedence constraints,
resource capacity constraints and time constraints. In particular
time constraints model tasks duedates and resource availability
time windows constraints. To improve the schedule robustness, we
modeled the concept of (a, b) super-solutions, where (a, b) are input
parameters of the COP model. An (a, b) super-solution is one in
which if a variables (i.e. the completion times of a culture tasks)
lose their values (i.e. cultures are contaminated), the solution can be
repaired by assigning these variables values with a new values (i.e.
the completion times of a backup culture tasks) and at most b other
variables (i.e. delaying the completion of at most b other tasks).
The efficiency and applicability of the proposed model is
demonstrated by solving instances taken from a real-life
pharmaceutical company. Computational results showed that
the determined super-solutions are near-optimal.
Abstract: The nickel-manganese (Ni-Mn) alloy coating prepared
from DC electrodeposition process in sulphamate bath was studied.
The effects of process parameters, such as current density and
electrolyte composition, on the cathodic current efficiency,
microstructure, internal stress and mechanical properties were
investigated. Because of its crucial effect on the application to the
electroforming of microelectronic components, the development of
low internal stress coating with high leveling power was emphasized.
It was found that both the coating’s manganese content and the
cathodic current efficiency increased with the raise in current density.
In addition, the internal stress of the deposited coating showed
compressive nature at low current densities while changed to tensile
one at higher current densities. Moreover, the metallographic
observation, X-ray diffraction measurement, and polarization curve
measurement were conducted. It was found that the Ni-Mn coating
consisted of nano-sized columnar grains and the maximum hardness of
the coating was associated with (111) preferred orientation in the
microstructure. The grain size was refined along with the increase in
the manganese content of the coating, which accordingly, raised its
hardness and resistance to annealing softening. In summary, the
Ni-Mn coating prepared at lower current density of 1-2 A/dm2 had low
internal stress, high leveling power, and better corrosion resistance.
Abstract: This study presents three different approaches to
estimate bubble point pressures for the binary system of CO2 and
ethyl palmitate fatty acid ethyl ester. The first method involves the
Peng-Robinson (PR) Equation of State (EoS) with the conventional
mixing rule of Van der Waals. The second approach involves the PR
EOS together with the Wong Sandler (WS) mixing rule, coupled with
the UNIQUAC GE model. In order to model the bubble point
pressures with this approach, the volume and area parameter for ethyl
palmitate were estimated by the Hansen group contribution method.
The last method involved the Peng-Robinson, combined with the
Wong-Sandler method, but using NRTL as the GE model. Results
using the Van der Waals mixing rule clearly indicated that this
method has the largest errors among all three methods, with errors in
the range of 3.96-6.22%. The PR-WS-UNIQUAC method exhibited
small errors, with average absolute deviations between 0.95 to 1.97
percent. The PR-WS-NRTL method led to the least errors, where
average absolute deviations ranged between 0.65-1.7%.
Abstract: This paper develops and investigates a framework for
the assessment of customer involvement in the service design process
of result oriented product-service systems in order to improve the
service offering in a business-to-business (B2B) context. The
framework comprises five main criteria and fifteen sub-criteria that
contribute to customer involvement in a hierarchy using a maturity
grid to highlight the strengths and weaknesses for each criterion. To
develop the customer involvement framework, an extensive literature
review related to service design, result oriented product-service
system (PSS) and customer involvement in service design was
carried out. Key factors that significantly influence customer
involvement from industry and literature were identified to develop
the framework. A major contribution of the developed framework
includes a hierarchy of appropriate criteria for assessing customer
involvement in the service design process within results oriented
PSS; the definition of four maturity levels which are suitable to
describe the whole spectrum of customer involvement in the service
design process; and finally, The paper concludes by enabling service
providers to: take proactive decisions; screen and evaluate new
services; improve perceived service quality; and provide barriers
against imitation.
Abstract: In this paper, we present a new segmentation approach
for focal liver lesions in contrast enhanced ultrasound imaging. This
approach, based on a two-cluster Fuzzy C-Means methodology,
considers type-II fuzzy sets to handle uncertainty due to the image
modality (presence of speckle noise, low contrast, etc.), and to
calculate the optimum inter-cluster threshold. Fine boundaries are
detected by a local recursive merging of ambiguous pixels. The
method has been tested on a representative database. Compared to
both Otsu and type-I Fuzzy C-Means techniques, the proposed
method significantly reduces the segmentation errors.
Abstract: This study aims to investigate the mixing behaviors of
deionized (DI) water and carboxymethyl cellulose (CMC) solutions in
C-shaped serpentine micromixers over a wide range of flow
conditions. The flow of CMC solutions exhibits shear-thinning
behaviors. Numerical simulations are performed to investigate the
effects of the mean flow speed, fluid properties and geometry
parameters on flow and mixing in the micromixers with the serpentine
channel of the same overall channel length. From the results, we can
find the following trends. When convection dominates fluid mixing,
the curvature-induced vortices enhance fluid mixing effectively. The
mixing efficiency of a micromixer consisting of semicircular C-shaped
repeating units with a smaller centerline radius is better than that of a
micromixer consisting of major segment repeating units with a larger
centerline radius. The viscosity of DI water is less than the overall
average apparent viscosity of CMC solutions, and so the effect of
curvature-induced vortices on fluid mixing in DI water is larger than
that in CMC solutions for the cases with the same mean flow speed.
Abstract: One of the most critical decision points in the design of a
face recognition system is the choice of an appropriate face representation.
Effective feature descriptors are expected to convey sufficient, invariant
and non-redundant facial information. In this work we propose a set of
Hahn moments as a new approach for feature description. Hahn moments
have been widely used in image analysis due to their invariance, nonredundancy
and the ability to extract features either globally and locally.
To assess the applicability of Hahn moments to Face Recognition we
conduct two experiments on the Olivetti Research Laboratory (ORL)
database and University of Notre-Dame (UND) X1 biometric collection.
Fusion of the global features along with the features from local facial
regions are used as an input for the conventional k-NN classifier. The
method reaches an accuracy of 93% of correctly recognized subjects for
the ORL database and 94% for the UND database.
Abstract: This study integrates a larger research empirical
project that examines second language (SL) learners’ profiles and
valid procedures to perform complete and diagnostic assessment in
schools. 102 learners of Portuguese as a SL aged 7 and 17 years
speakers of distinct home languages were assessed in several
linguistic tasks. In this article, we focused on writing performance in
the specific task of narrative essay composition. The written outputs
were measured using the score in six components adapted from an
English SL assessment context (Alberta Education): linguistic
vocabulary, grammar, syntax, strategy, socio-linguistic, and
discourse. The writing processes and strategies in Portuguese
language used by different immigrant students were analysed to
determine features and diversity of deficits on authentic texts
performed by SL writers. Differentiated performance was based on
the diversity of the following variables: grades, previous schooling,
home language, instruction in first language, and exposure to
Portuguese as Second Language. Indo-Aryan languages speakers
showed low writing scores compared to their peers and the type of
language and respective cognitive mapping (such as Mandarin and
Arabic) was the predictor, not linguistic distance. Home language
instruction should also be prominently considered in further research
to understand specificities of cognitive academic profile in a
Romance languages learning context. Additionally, this study also
examined the teachers’ representations that will be here addressed to
understand educational implications of second language teaching in
psychological distress of different minorities in schools of specific
host countries.
Abstract: Conductivity properties of DNA molecule is
investigated in a simple, but chemically specific approach that is
intimately related to the Su-Schrieffer-Heeger (SSH) model. This
model is a tight-binding linear nanoscale chain. We have tried to
study the electrical current flowing in DNA and investigated the
characteristic I-V diagram. As a result, It is shown that there are the
(quasi-) ohmic areas in I-V diagram. On the other hand, the regions
with a negative differential resistance (NDR) are detectable in
diagram.
Abstract: Speaker Identification (SI) is the task of establishing
identity of an individual based on his/her voice characteristics. The SI
task is typically achieved by two-stage signal processing: training and
testing. The training process calculates speaker specific feature
parameters from the speech and generates speaker models
accordingly. In the testing phase, speech samples from unknown
speakers are compared with the models and classified. Even though
performance of speaker identification systems has improved due to
recent advances in speech processing techniques, there is still need of
improvement. In this paper, a Closed-Set Tex-Independent Speaker
Identification System (CISI) based on a Multiple Classifier System
(MCS) is proposed, using Mel Frequency Cepstrum Coefficient
(MFCC) as feature extraction and suitable combination of vector
quantization (VQ) and Gaussian Mixture Model (GMM) together
with Expectation Maximization algorithm (EM) for speaker
modeling. The use of Voice Activity Detector (VAD) with a hybrid
approach based on Short Time Energy (STE) and Statistical
Modeling of Background Noise in the pre-processing step of the
feature extraction yields a better and more robust automatic speaker
identification system. Also investigation of Linde-Buzo-Gray (LBG)
clustering algorithm for initialization of GMM, for estimating the
underlying parameters, in the EM step improved the convergence rate
and systems performance. It also uses relative index as confidence
measures in case of contradiction in identification process by GMM
and VQ as well. Simulation results carried out on voxforge.org
speech database using MATLAB highlight the efficacy of the
proposed method compared to earlier work.
Abstract: This paper deals with nonlinear vibration analysis
using finite element method for frame structures consisting of elastic
and viscoelastic damping layers supported by multiple nonlinear
concentrated springs with hysteresis damping. The frame is supported
by four nonlinear concentrated springs near the four corners. The
restoring forces of the springs have cubic non-linearity and linear
component of the nonlinear springs has complex quantity to represent
linear hysteresis damping. The damping layer of the frame structures
has complex modulus of elasticity. Further, the discretized equations in
physical coordinate are transformed into the nonlinear ordinary
coupled differential equations using normal coordinate corresponding
to linear natural modes. Comparing shares of strain energy of the
elastic frame, the damping layer and the springs, we evaluate the
influences of the damping couplings on the linear and nonlinear impact
responses. We also investigate influences of damping changed by
stiffness of the elastic frame on the nonlinear coupling in the damped
impact responses.
Abstract: A large amount of software products offer a wide
range and number of features. This is called featuritis or creeping
featurism and tends to rise with each release of the product. Feautiris
often adds unnecessary complexity to software, leading to longer
learning curves and overall confusing the users and degrading their
experience. We take a look to a new design approach tendency that
has been coming up, the so-called “What You Get is What You
Need” concept that argues that products should be very focused,
simple and with minimalistic interfaces in order to help users conduct
their tasks in distraction-free ambiences. This isn’t as simple to
implement as it might sound and the developers need to cut down
features. Our contribution illustrates and evaluates this design method
through a novel distraction-free diagramming tool named Delineato
Pro for Mac OS X in which the user is confronted with an empty
canvas when launching the software and where tools only show up
when really needed.
Abstract: Barley (Hordeum vulgare L.), vetch (Vicia villosa),
and grass pea (Lathyrus sativus L.) monocultures as well as mixtures
of barley with each of the above legumes, in three seeding ratios (i.e.,
barley: legume 75:25, 50:50 and 25:75, based on seed numbers) were
used to investigated forage yield and competition indices. The results
showed that intercropping reduced the dry matter yield of the three
component plants, compared with their respective monocrops. The
greatest value of total dry matter yield was obtained from barley25-
grasspea75 (5.44 t ha-1) mixture, followed by grass pea sole crop (4.99
t ha-1). The total actual yield loss (AYL) values were positive and
greater than 0 in all mixtures, indicating an advantage from
intercropping over sole crops. Intercropped barley had a higher
relative crowding coefficient (K=1.64) than intercropped legumes
(K=1.20), indicating that barley was more competitive than legumes
in mixtures. Furthermore, grass pea was more competitive than vetch
in mixtures with barley. The highest land equivalent ratio (LER),
system productivity index (SPI) and monetary advantage index
(MAI) were obtained when barley was mixed at a rate of 25% with
75% seed rate of grass pea. It is concluded that intercropping of
barley with grass pea has a good potential to improve the
performance of forage with high land-use efficiency.
Abstract: Over the past few years, a lot of research has been
conducted to bring Automatic Speech Recognition (ASR) into various
areas of Air Traffic Control (ATC), such as air traffic control
simulation and training, monitoring live operators for with the aim
of safety improvements, air traffic controller workload measurement
and conducting analysis on large quantities controller-pilot speech.
Due to the high accuracy requirements of the ATC context and its
unique challenges, automatic speech recognition has not been widely
adopted in this field. With the aim of providing a good starting
point for researchers who are interested bringing automatic speech
recognition into ATC, this paper gives an overview of possibilities
and challenges of applying automatic speech recognition in air traffic
control. To provide this overview, we present an updated literature
review of speech recognition technologies in general, as well as
specific approaches relevant to the ATC context. Based on this
literature review, criteria for selecting speech recognition approaches
for the ATC domain are presented, and remaining challenges and
possible solutions are discussed.
Abstract: The use of Flexible AC Transmission System
(FACTS) devices in a power system can potentially overcome
limitations of the present mechanically controlled transmission
system. Also, the advance of technology makes possible to include
new energy storage devices in the electrical power system. The
integration of Superconducting Magnetic Energy Storage (SMES)
into Static Synchronous Compensator (STATCOM) can lead to
increase their flexibility in improvement of power system dynamic
behaviour by exchanging both active and reactive powers with power
grids. This paper describes structure and behaviour of SMES,
specifications and performance principles of the STATCOM/SMES
compensator. Moreover, the benefits and effectiveness of integrated
SMES with STATCOM in power systems is presented. Also, the
performance of the STATCOM/SMES compensator is evaluated
using an IEEE 3-bus system through the dynamic simulation by
PSCAD/EMTDC software.
Abstract: High frequency automotive interior noise above 500
Hz considerably affects automotive passenger comfort. To reduce this
noise, sound insulation material is often laminated on body panels or
interior trim panels. For a more effective noise reduction, the sound
reduction properties of this laminated structure need to be estimated.
We have developed a new calculate tool that can roughly calculate the
sound absorption and insulation properties of laminate structure and
handy for designers. In this report, the outline of this tool and an
analysis example applied to floor mat are introduced.