Abstract: The aim of this work is to study the possible use of
stone cutting sludge waste in concrete production, which would
reduce both the environmental impact and the production cost .Slurry
sludge was used a source of water in concrete production, which was
obtained from Samara factory/Jordan, The physico-chemical and
mineralogical characterization of the sludge was carried out to
identify the major components and to compare it with the typical
sand used to produce concrete. Samples analysis showed that 96% of
slurry sludge volume is water, so it should be considered as an
important source of water. Results indicated that the use of slurry
sludge as water source in concrete production has insignificant effect
on compression strength, while it has a sharp effect on the slump
values. Using slurry sludge with a percentage of 25% of the total
water content obtained successful concrete samples regarding slump
and compression tests. To clarify slurry sludge, settling process can
be used to remove the suspended solid. A settling period of 30 min.
obtained 99% removal efficiency. The clarified water is suitable for
using in concrete mixes, which reduce water consumption, conserve
water recourses, increase the profit, reduce operation cost and save
the environment. Additionally, the dry sludge could be used in the
mix design instead of the fine materials with sizes < 160 um. This
application could conserve the natural materials and solve the
environmental and economical problem caused by sludge
accumulation.
Abstract: The paper presents the Romanian realities and perspectives from the point of view of reaching the sustainable development model in the context of the recent accession to the European Union, based on the analysis of the indicators listed in the EU Sustainable Development Strategy. The analysis of the economic-social potential for sustainable development and of the environment aspects show that the objectives stipulated in the renewed EU Sustainable Development Strategy of 2006 can be reached, but an extra effort must be put-in in order to overcome the existing substantial gaps in several areas in relation to the developed countries of the EU. The paper-s conclusions show that even if sustainable development is not an easy target to reach in Romania, there are resources and a growing potential, which can lead to sustainable development if used rationally.
Abstract: Group contribution methods such as the UNIFAC are
of major interest to researchers and engineers involved synthesis,
feasibility studies, design and optimization of separation processes as
well as other applications of industrial use. Reliable knowledge of
the phase equilibrium behavior is crucial for the prediction of the fate
of the chemical in the environment and other applications. The
objective of this study was to predict the solubility of selected
volatile organic compounds (VOCs) in glycol polymers and
biodiesel. Measurements can be expensive and time consuming,
hence the need for thermodynamic models. The results obtained in
this study for the infinite dilution activity coefficients compare very
well those published in literature obtained through measurements. It
is suggested that in preliminary design or feasibility studies of
absorption systems for the abatement of volatile organic compounds,
prediction procedures should be implemented while accurate fluid
phase equilibrium data should be obtained from experiment.
Abstract: There is an urgent need to conserve the biological diversity of the Nigerian Environment for the future and present generation in the face of current energy resources development. This paper gives an in-depth analysis of the impact of oil and gas activities on the biological diversity of the Nigerian Niger Delta area and its consequences on the sustainable development of the host communities as it relates to their social, economic and environmental issues, particularly on the womenfolk who are the key managers of environmental resources. Also reviewed is the frustration of these communities that is reflected in unending conflicts.
Abstract: A handful of propagation textbooks that discuss radio frequency (RF) propagation models merely list out the models and perhaps discuss them rather briefly; this may well be frustrating for the potential first time modeller who's got no idea on how these models could have been derived. This paper fundamentally provides an overture in modelling the radio channel. Explicitly, for the modelling practice discussed here, signal strength field measurements had to be conducted beforehand (this was done at 469 MHz); to be precise, this paper primarily concerns empirically/statistically modelling the radio channel, and thus provides results obtained from empirically modelling the environments in question. This paper, on the whole, proposes three propagation models, corresponding to three experimented environments. Perceptibly, the models have been derived by way of making the most use of statistical measures. Generally speaking, the first two models were derived via simple linear regression analysis, whereas the third have been originated using multiple regression analysis (with five various predictors). Additionally, as implied by the title of this paper, both indoor and outdoor environments have been experimented; however, (somewhat) two of the environments are neither entirely indoor nor entirely outdoor. The other environment, however, is completely indoor.
Abstract: Automatic methods of detecting changes through
satellite imaging are the object of growing interest, especially
beca²use of numerous applications linked to analysis of the Earth’s
surface or the environment (monitoring vegetation, updating maps,
risk management, etc...). This work implemented spatial analysis
techniques by using images with different spatial and spectral
resolutions on different dates. The work was based on the principle
of control charts in order to set the upper and lower limits beyond
which a change would be noted. Later, the a contrario approach was
used. This was done by testing different thresholds for which the
difference calculated between two pixels was significant. Finally,
labeled images were considered, giving a particularly low difference
which meant that the number of “false changes” could be estimated
according to a given limit.
Abstract: Although oil-based drilling fluids are of paramount practical and economical interest, they represent a serious source of pollution, once released into the environment as drill cuttings. The aim of this study is to assess the capability of isolated microorganisms to degrade gasoil fuel. The commonly used physicochemical and biodegradation remediation techniques of petroleum contaminated soil were both investigated. The study revealed that natural biodegradation is favorable. Even though, the presence of heavy metals, the moisture level of (8.55%) and nutrient deficiencies put severe constrains on microorganisms- survival ranges inhibiting the biodegradation process. The selected strains were able to degrade the diesel fuel at significantly high rates (around 98%).
Abstract: Due to the environmental and price issues of current
energy crisis, scientists and technologists around the globe are
intensively searching for new environmentally less-impact form of
clean energy that will reduce the high dependency on fossil fuel.
Particularly hydrogen can be produced from biomass via thermochemical
processes including pyrolysis and gasification due to the
economic advantage and can be further enhanced through in-situ
carbon dioxide removal using calcium oxide. This work focuses on
the synthesis and development of the flowsheet for the enhanced
biomass gasification process in PETRONAS-s iCON process
simulation software. This hydrogen prediction model is conducted at
operating temperature between 600 to 1000oC at atmospheric
pressure. Effects of temperature, steam-to-biomass ratio and
adsorbent-to-biomass ratio were studied and 0.85 mol fraction of
hydrogen is predicted in the product gas. Comparisons of the results
are also made with experimental data from literature. The
preliminary economic potential of developed system is RM 12.57 x
106 which equivalent to USD 3.77 x 106 annually shows economic
viability of this process.
Abstract: Air quality studies were carried out in the towns of
Putrajaya, Petaling Jaya and Nilai in the Malaysian Peninsular. In this
study, the variations of Ozone (O3) concentrations over a four year
period (2008-2011) were investigated using data obtained from the
Malaysian Department of the Environment (DOE). This study aims to
identify and describe the daily and monthly variations of O3
concentrations at the monitoring sites mentioned. The SPPS program
(Statistical Package for the Social Science) was used to analyze this
data in order to obtain the variations of O3 and also to clarify the
relationship between the stations. The findings of the study revealed
that the highest concentration of O3 occurred during the midday and
afternoon (between 13:00-15:00 hrs). The comparison between
stations also showed that highest O3 concentrations were recorded in
Putrajaya. The comparisons of average and maximum concentrations
of O3 for the three stations showed that the strongest significant
correlation was recorded in the Petaling Jaya station with the value
R2= 0.667. Results from this study indicate that in the urban areas of
Peninsular Malaysia, the concentration of O3 depends on the
concentration of NOx. Furthermore, HYSPLIT back trajectories
(-72h) indicated that air-mass transport patterns can also influence the
O3 concentration in the areas studied.
Abstract: Environmental aspects plays a central role in environmental management system (EMS) because it is the basis for the identification of an organization-s environmental targets. The
existing methods for the assessment of environmental aspects are grouped into three categories: risk assessment-based (RA-based),
LCA-based and criterion-based methods. To combine the benefits of
these three categories of research, this study proposes an integrated framework, combining RA-, LCA- and criterion-based methods. The
integrated framework incorporates LCA techniques for the identification of the causal linkage for aspect, pathway, receptor and
impact, uses fuzzy logic to assess aspects, considers fuzzy conditions,
in likelihood assessment, and employs a new multi-criteria decision analysis method - multi-criteria and multi-connection comprehensive
assessment (MMCA) - to estimate significant aspects in EMS. The proposed model is verified, using a real case study and the results show
that this method successfully prioritizes the environmental aspects.
Abstract: As global industry developed rapidly, the energy
demand also rises simultaneously. In the production process, there’s a
lot of energy consumed in the process. Formally, the energy used in
generating the heat in the production process. In the total energy
consumption, 40% of the heat was used in process heat, mechanical
work, chemical energy and electricity. The remaining 50% were
released into the environment. It will cause energy waste and
environment pollution. There are many ways for recovering the waste
heat in factory. Organic Rankine Cycle (ORC) system can produce
electricity and reduce energy costs by recovering the waste of low
temperature heat in the factory. In addition, ORC is the technology
with the highest power generating efficiency in low-temperature heat
recycling. However, most of factories executives are still hesitated
because of the high implementation cost of the ORC system, even a lot
of heat are wasted. Therefore, this study constructs a nonlinear
mathematical model of waste heat recovery equipment configuration
to maximize profits. A particle swarm optimization algorithm is
developed to generate the optimal facility installation plan for the ORC
system.
Abstract: The pavement constructions on soft and expansive soils are not durable and unable to sustain heavy traffic loading. As a result, pavement failures and settlement problems will occur very often even under light traffic loading due to cyclic and rolling effects. Geotechnical engineers have dwelled deeply into this matter, and adopt various methods to improve the engineering characteristics of soft fine-grained soils and expansive soils. The problematic soils are either replaced by good and better quality material or treated by using chemical stabilization with various binding materials. Increased the strength and durability are also the part of the sustainability drive to reduce the environment footprint of the built environment by the efficient use of resources and waste recycle materials. This paper presents a series of laboratory tests and evaluates the effect of cement and fly ash on the strength and drainage characteristics of soil in Miri. The tests were performed at different percentages of cement and fly ash by dry weight of soil. Additional tests were also performed on soils treated with the combinations of fly ash with cement and lime. The results of this study indicate an increase in unconfined compression strength and a decrease in hydraulic conductivity of the treated soil.
Abstract: Many foreign and Lithuanian scientists, analyzing the
evaluation of the tax system in respect of the burden of taxation,
agree that the latter, in principle, depends on how many individuals
and what units of the residents constitute a household. Therefore, the
aim of scientific research is to substantiate or to deny the significance
of a household, but not a resident, as a statistical unit, during the
evaluation of tax system, to be precise, determination of the value of
the burden of taxation. A performed scientific research revealed that
evaluation of the tax system in respect of a household, but not a
resident, as a statistical unit, allows not only to evaluate the
efficiency of the tax system more objectively, but also to forecast
practicably existing poverty line, burden of taxation, and to
capacitate the initiation of efficient decisions in social and tax fields
creating the environment of existence.
Abstract: Air pollution is a major environmental health
problem, affecting developed and developing countries around the
world. Increasing amounts of potentially harmful gases and
particulate matter are being emitted into the atmosphere on a global
scale, resulting in damage to human health and the environment.
Petroleum-related air pollutants can have a wide variety of adverse
environmental impacts. In the crude oil production sectors, there is a
strong need for a thorough knowledge of gaseous emissions resulting
from the flaring of associated gas of known composition on daily
basis through combustion activities under several operating
conditions. This can help in the control of gaseous emission from
flares and thus in the protection of their immediate and distant
surrounding against environmental degradation.
The impacts of methane and non-methane hydrocarbons emissions
from flaring activities at oil production facilities at Kuwait Oilfields
have been assessed through a screening study using records of flaring
operations taken at the gas and oil production sites, and by analyzing
available meteorological and air quality data measured at stations
located near anthropogenic sources. In the present study the
Industrial Source Complex (ISCST3) Dispersion Model is used to
calculate the ground level concentrations of methane and nonmethane
hydrocarbons emitted due to flaring in all over Kuwait
Oilfields.
The simulation of real hourly air quality in and around oil
production facilities in the State of Kuwait for the year 2006,
inserting the respective source emission data into the ISCST3
software indicates that the levels of non-methane hydrocarbons from
the flaring activities exceed the allowable ambient air standard set by
Kuwait EPA. So, there is a strong need to address this acute problem
to minimize the impact of methane and non-methane hydrocarbons
released from flaring activities over the urban area of Kuwait.
Abstract: As the gradual increase of the enterprise scale, the
firms may possess many manufacturing plants located in different
places geographically. This change will result in the multi-site
production planning problems under the environment of multiple
plants or production resources. Our research proposes the structural
framework to analyze the multi-site planning problems. The analytical
framework is composed of six elements: multi-site conceptual model,
product structure (bill of manufacturing), production strategy,
manufacturing capability and characteristics, production planning
constraints, and key performance indicators. As well as the discussion
of these six ingredients, we also review related literatures in this paper
to match our analytical framework. Finally we take a real-world
practical example of a TFT-LCD manufacturer in Taiwan to explain
our proposed analytical framework for the multi-site production
planning problems.
Abstract: Selection of the best possible set of suppliers has a
significant impact on the overall profitability and success of any
business. For this reason, it is usually necessary to optimize all
business processes and to make use of cost-effective alternatives for
additional savings. This paper proposes a new efficient context-aware
supplier selection model that takes into account possible changes of
the environment while significantly reducing selection costs. The
proposed model is based on data clustering techniques while
inspiring certain principles of online algorithms for an optimally
selection of suppliers. Unlike common selection models which re-run
the selection algorithm from the scratch-line for any decision-making
sub-period on the whole environment, our model considers the
changes only and superimposes it to the previously defined best set
of suppliers to obtain a new best set of suppliers. Therefore, any recomputation
of unchanged elements of the environment is avoided
and selection costs are consequently reduced significantly. A
numerical evaluation confirms applicability of this model and proves
that it is a more optimal solution compared with common static
selection models in this field.
Abstract: This study aimed to detect and to identify the main
strains of airborne microorganisms present in the Shanghai Metro
system. Samples were collected using agar plates exposed to the air
and microorganisms were identified using catalase, plasma coagulase
and hymolytic analysis. The results show that the concentration of
mildew present within a newly opened metro line was significantly
higher than for other lines. Differences among underground and
elevated stations can be attributed to differences in passenger flow and
the environment surrounding the stations. Additionally, the
investigation indicated that bacteria reached maximum levels at
different times on weekdays and weekends. The bacteria in the Metro
stations were identified as primarily Gram positive, consisting mainly
of coagulase-negative staphylococcus strains (CNS).
Abstract: Rice husk is one of the alternative fuels for Thailand because of its high potential and environmental benefits. Nonetheless, the environmental profile of the electricity production from rice husk must be assessed to ensure reduced environmental damage. A 10 MW pilot plant using rice husk as feedstock is the study site. The environmental impacts from rice husk power plant are evaluated by using the Life Cycle Assessment (LCA) methodology. Energy, material and carbon balances have been determined for tracing the system flow. Carbon closure has been used for describing of the net amount of CO2 released from the system in relation to the amount being recycled between the power plant and the CO2 adsorbed by rice husk. The transportation of rice husk to the power plant has significant on global warming, but not on acidification and photo-oxidant formation. The results showed that the impact potentials from rice husk power plant are lesser than the conventional plants for most of the categories considered; except the photo-oxidant formation potential from CO. The high CO from rice husk power plant may be due to low boiler efficiency and high moisture content in rice husk. The performance of the study site can be enhanced by improving the combustion efficiency.
Abstract: Business transformation initiatives are required by
any organization to jump from its normal mode of operation to the
one that is suitable for the change in the environment such as
competitive pressures, regulatory requirements, changes in labor
market, etc., or internal such as changes in strategy/vision, changes in
the capability, change in the management, etc. Recent advances in
information technology in automating the business processes have
the potential to transform an organization to provide it with a
sustained competitive advantage. Process constitutes the skeleton of
a business. Thus, for a business to exist and compete well, it is
essential for the skeleton to be robust and agile. This paper details
“transformation" from a business perspective, methodologies to bring
about an effective transformation, process-based transformation, and
the role of services computing in this. Further, it details the benefits
that could be achieved through services computing.
Abstract: The production of a plant can be measured in terms of
seeds. The generation of seeds plays a critical role in our social and
daily life. The fruit production which generates seeds, depends on the
various parameters of the plant, such as shoot length, leaf number,
root length, root number, etc When the plant is growing, some leaves
may be lost and some new leaves may appear. It is very difficult to
use the number of leaves of the tree to calculate the growth of the
plant.. It is also cumbersome to measure the number of roots and
length of growth of root in several time instances continuously after
certain initial period of time, because roots grow deeper and deeper
under ground in course of time. On the contrary, the shoot length of
the tree grows in course of time which can be measured in different
time instances. So the growth of the plant can be measured using the
data of shoot length which are measured at different time instances
after plantation. The environmental parameters like temperature, rain
fall, humidity and pollution are also play some role in production of
yield. The soil, crop and distance management are taken care to
produce maximum amount of yields of plant. The data of the growth
of shoot length of some mustard plant at the initial stage (7,14,21 &
28 days after plantation) is available from the statistical survey by a
group of scientists under the supervision of Prof. Dilip De. In this
paper, initial shoot length of Ken( one type of mustard plant) has
been used as an initial data. The statistical models, the methods of
fuzzy logic and neural network have been tested on this mustard
plant and based on error analysis (calculation of average error) that
model with minimum error has been selected and can be used for the
assessment of shoot length at maturity. Finally, all these methods
have been tested with other type of mustard plants and the particular
soft computing model with the minimum error of all types has been
selected for calculating the predicted data of growth of shoot length.
The shoot length at the stage of maturity of all types of mustard
plants has been calculated using the statistical method on the
predicted data of shoot length.