Abstract: Compost manufacturing plants are one of units where
wastewater is produced in significantly large amounts. Wastewater
produced in these plants contains high amounts of substrate (organic
loads) and is classified as stringent waste which creates significant
pollution when discharged into the environment without treatment. A
compost production plant in the one of the Iran-s province treating
200 tons/day of waste is one of the most important environmental
pollutant operations in this zone. The main objectives of this paper
are to investigate the compost wastewater treatability in hybrid
anaerobic reactors with an upflow-downflow arrangement, to
determine the kinetic constants, and eventually to obtain an
appropriate mathematical model. After starting the hybrid anaerobic
reactor of the compost production plant, the average COD removal
rate efficiency was 95%.
Abstract: Both prognostic and diagnostic modes of a 3D baroclinic
model in hydrodynamic and sediment transport models of
the Princeton Ocean Model (POM) were conducted to separate
prognose and diagnose effects of different hydrodynamic factors on
transport of suspended sediment discharged from the rivers to the
Gulf of Thailand (GoT). Both transport modes of suspended sediment
distribution in the GoT were numerically simulated. It could be
concluded that the suspended sediment discharged from the rivers
around the GoT. Most of sediments in estuaries and coastal areas are
deposited outside the GoT under the condition of wind-driven current,
and very small amount of the sediments of them are transported
faraway. On the basis of wind forcing, sediments from the lower
GoT to the upper GoT are mainly transported south-northwestward
and also continuously moved north-southwestward. An obvious 3D
characteristic of suspended sediment transport is produced in the
wind-driven current residual circulation condition. In this study, the
transport patterns at the third layer are generally consistent with
the typhoon-induced strong currents in two case studies of Typhoon
Linda 1997. The case studies presented the prognostic and diagnostic
modes during 00UTC28OCT1997 to 12UTC06NOV1997 in a short
period with the current condition for pre-operation of the suspended
sediment transport model in estuaries and coastal areas.
Abstract: This paper examines the use of mechanical aerator for
oxidation-ditch process. The rotor, which controls the aeration, is the
main component of the aeration process. Therefore, the objective of
this study is to find out the variations in overall oxygen transfer
coefficient (KLa) and aeration efficiency (AE) for different
configurations of aerator by varying the parameters viz. speed of
aerator, depth of immersion, blade tip angles so as to yield higher
values of KLa and AE. Six different configurations of aerator were
developed and fabricated in the laboratory and were tested for abovementioned
parameters. The curved blade rotor (CBR) emerged as a
potential aerator with blade tip angle of 47°.
The mathematical models are developed for predicting the
behaviour of CBR w.r.t kLa and power. In laboratory studies, the
optimum value of KLa and AE were observed to be 10.33 h-1 and
2.269 kg O2/ kWh.
Abstract: To understand life as biological system, evolutionary
understanding is indispensable. Protein interactions data are rapidly
accumulating and are suitable for system-level evolutionary analysis.
We have analyzed yeast protein interaction network by both
mathematical and biological approaches. In this poster presentation,
we inferred the evolutionary birth periods of yeast proteins by
reconstructing phylogenetic profile. It has been thought that hub
proteins that have high connection degree are evolutionary old. But
our analysis showed that hub proteins are entirely evolutionary new.
We also examined evolutionary processes of protein complexes. It
showed that member proteins of complexes were tend to have
appeared in the same evolutionary period. Our results suggested that
protein interaction network evolved by modules that form the
functional unit. We also reconstructed standardized phylogenetic trees
and calculated evolutionary rates of yeast proteins. It showed that
there is no obvious correlation between evolutionary rates and
connection degrees of yeast proteins.
Abstract: Response Surface Methodology (RSM) is a powerful
and efficient mathematical approach widely applied in the
optimization of cultivation process. Cellulase enzyme production by
Trichoderma reesei RutC30 using agricultural waste rice straw and
banana fiber as carbon source were investigated. In this work,
sequential optimization strategy based statistical design was
employed to enhance the production of cellulase enzyme through
submerged cultivation. A fractional factorial design (26-2) was applied
to elucidate the process parameters that significantly affect cellulase
production. Temperature, Substrate concentration, Inducer
concentration, pH, inoculum age and agitation speed were identified
as important process parameters effecting cellulase enzyme synthesis.
The concentration of lignocelluloses and lactose (inducer) in the
cultivation medium were found to be most significant factors. The
steepest ascent method was used to locate the optimal domain and a
Central Composite Design (CCD) was used to estimate the quadratic
response surface from which the factor levels for maximum
production of cellulase were determined.
Abstract: Computational simulation of steam flow and heat transfer in power plant condensers on the basis of the threedimensional mathematical model for the flow through porous media is presented. In order to solve the mathematical model of steam flow and heat transfer in power plant condensers, the Streamline Upwind Petrov-Galerkin finite element method is applied. By comparison of the results of simulation with experimental results about an experimental condenser, it is confirmed that SUPG finite element method can be successfully applied for solving the three-dimensional mathematical model of steam flow and heat transfer in power plant condensers.
Abstract: To investigate some relations between higher mathe¬matics scores in Chinese graduate student entrance examination and calculus (resp. linear algebra, probability statistics) scores in subject's completion examination of Chinese university, we select 20 students as a sample, take higher mathematics score as a decision attribute and take calculus score, linear algebra score, probability statistics score as condition attributes. In this paper, we are based on rough-set theory (Rough-set theory is a logic-mathematical method proposed by Z. Pawlak. In recent years, this theory has been widely implemented in the many fields of natural science and societal science.) to investigate importance of condition attributes with respective to decision attribute and strength of condition attributes supporting decision attribute. Results of this investigation will be helpful for university students to raise higher mathematics scores in Chinese graduate student entrance examination.
Abstract: In this paper an alternative analysis in the time
domain is described and the results of the interpolation process are
presented by means of functions that are based on the rule of
conditional mathematical expectation and the covariance function. A
comparison between the interpolation error caused by low order
filters and the classic sinc(t) truncated function is also presented.
When fewer samples are used, low-order filters have less error. If the
number of samples increases, the sinc(t) type functions are a better
alternative. Generally speaking there is an optimal filter for each
input signal which depends on the filter length and covariance
function of the signal. A novel scheme of work for adaptive
interpolation filters is also presented.
Abstract: In the present paper the displacement-based nonconforming quadrilateral affine thin plate bending finite element ARPQ4 is presented, derived directly from non-conforming quadrilateral thin plate bending finite element RPQ4 proposed by Wanji and Cheung [19]. It is found, however, that element RPQ4 is only conditionally unisolvent. The new element is shown to be inherently unisolvent. This convenient property results in the element ARPQ4 being more robust and thus better suited for computations than its predecessor. The convergence is proved and the rate of convergence estimated. The mathematically rigorous proof of convergence presented in the paper is based on Stummel-s generalized patch test and the consideration of the element approximability condition, which are both necessary and sufficient for convergence.
Abstract: In this paper, an automatic determination algorithm for nuclear magnetic resonance (NMR) spectra of the metabolites in the living body by magnetic resonance spectroscopy (MRS) without human intervention or complicated calculations is presented. In such method, the problem of NMR spectrum determination is transformed into the determination of the parameters of a mathematical model of the NMR signal. To calculate these parameters efficiently, a new model called modified Hopfield neural network is designed. The main achievement of this paper over the work in literature [30] is that the speed of the modified Hopfield neural network is accelerated. This is done by applying cross correlation in the frequency domain between the input values and the input weights. The modified Hopfield neural network can accomplish complex dignals perfectly with out any additinal computation steps. This is a valuable advantage as NMR signals are complex-valued. In addition, a technique called “modified sequential extension of section (MSES)" that takes into account the damping rate of the NMR signal is developed to be faster than that presented in [30]. Simulation results show that the calculation precision of the spectrum improves when MSES is used along with the neural network. Furthermore, MSES is found to reduce the local minimum problem in Hopfield neural networks. Moreover, the performance of the proposed method is evaluated and there is no effect on the performance of calculations when using the modified Hopfield neural networks.
Abstract: The aim of this study is to develop mathematical
relationships for the performance parameter brake thermal efficiency
(BTE) and emission parameter nitrogen oxides (NOx) for the various
esters of vegetable oils used as CI engine fuel. The BTE is an
important performance parameter defining the ability of engine to
utilize the energy supplied and power developed similarly it is
indication of efficiency of fuels used. The esters of cottonseed oil,
soybean oil, jatropha oil and hingan oil are prepared using
transesterification process and characterized for their physical and
main fuel properties including viscosity, density, flash point and
higher heating value using standard test methods. These esters are
tried as CI engine fuel to analyze the performance and emission
parameters in comparison to diesel. The results of the study indicate
that esters as a fuel does not differ greatly with that of diesel in
properties. The CI engine performance with esters as fuel is in line
with the diesel where as the emission parameters are reduced with the
use of esters.
The correlation developed between BTE and brake power(BP),
gross calorific value(CV), air-fuel ratio(A/F), heat carried away by
cooling water(HCW). Another equation is developed between the
NOx emission and CO, HC, smoke density (SD), exhaust gas
temperature (EGT). The equations are verified by comparing the
observed and calculated values which gives the coefficient of
correlation of 0.99 and 0.96 for the BTE and NOx equations
respectively.
Abstract: This paper details a new concept of using compressed air as a potential zero pollution power source for motorbikes. In place of an internal combustion engine, the motorbike is equipped with an air turbine transforms the energy of the compressed air into shaft work. The mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine is presented in this paper. The effect of isobaric admission and adiabatic expansion of high pressure air for different rotor diameters, casing diameters and ratio of rotor to casing diameters of the turbine have been considered and analyzed. It is concluded that the work output is found optimum for some typical values of rotor / casing diameter ratios. In this study, the maximum power works out to 3.825 kW (5.20 HP) for casing diameter of 200 mm and rotor to casing diameter ratio of 0.65 to 0.60 which is sufficient to run motorbike.
Abstract: The optimal operation of proton exchange membrane fuel cell (PEMFC) requires good water management which is presented under two forms vapor and liquid. Moreover, fuel cells have to reach higher output require integration of some accessories which need electrical power. In order to analyze fuel cells operation and different species transport phenomena a biphasic mathematical model is presented by governing equations set. The numerical solution of these conservation equations is calculated by Matlab program. A multi-criteria optimization with weighting between two opposite objectives is used to determine the compromise solutions between maximum output and minimal stack size. The obtained results are in good agreement with available literature data.
Abstract: The Principal component regression (PCR) is a
combination of principal component analysis (PCA) and multiple linear regression (MLR). The objective of this paper is to revise the
use of PCR in shortwave near infrared (SWNIR) (750-1000nm) spectral analysis. The idea of PCR was explained mathematically and
implemented in the non-destructive assessment of the soluble solid
content (SSC) of pineapple based on SWNIR spectral data. PCR achieved satisfactory results in this application with root mean
squared error of calibration (RMSEC) of 0.7611 Brix°, coefficient of determination (R2) of 0.5865 and root mean squared error of crossvalidation
(RMSECV) of 0.8323 Brix° with principal components
(PCs) of 14.
Abstract: It is believed that continuously variable transmission (CVT) will dominate the automotive transmissions in the future. The most popular design is Van Doorne-s CVT with single metal pushing V-belt. However, it is only applicable to low power passenger cars because its major limitation is low torque capacity. Therefore, this research studies a novel dual-belt CVT system to overcome the limitation of traditional single-belt CVT, such that it can be applicable to the heavy-duty vehicles. This paper presents the mathematical model of the design and its experimental verification. Experimental and simulated results show that the model developed is valid and the proposed dual-belt CVT can really overcome the traditional limitation of single-belt Van Doorne-s CVT.
Abstract: In this paper presents the mathematical model of
hydrothermal processes in thermal power plant with different wind
direction scenarios in the water reservoir, which is solved by the
Navier - Stokes and temperature equations for an incompressible
fluid in a stratified medium. Numerical algorithm based on the
method of splitting by physical parameters. Three dimensional
Poisson equation is solved with Fourier method by combination of
tridiagonal matrix method (Thomas algorithm).
Abstract: In many applications, magnetic suspension systems
are required to operate over large variations in air gap. As a result,
the nonlinearities inherent in most types of suspensions have a
significant impact on performance. Specifically, it may be difficult to
design a linear controller which gives satisfactory performance,
stability, and disturbance rejection over a wide range of operating
points. in this paper an optimal controller based on discontinuous
mathematical model of the system for an electromagnetic suspension
system which is applied in magnetic trains has been designed .
Simulations show that the new controller can adapt well to the
variance of suspension mass and gap, and keep its dynamic
performance, thus it is superior to the classic controller.
Abstract: This paper systematically investigates the timedependent
health outcomes for office staff during computer work
using the developed mathematical model. The model describes timedependent
health outcomes in multiple body regions associated with
computer usage. The association is explicitly presented with a doseresponse
relationship which is parametrized by body region
parameters. Using the developed model we perform extensive
investigations of the health outcomes statically and dynamically. We
compare the risk body regions and provide various severity rankings
of the discomfort rate changes with respect to computer-related
workload dynamically for the study population. Application of the
developed model reveals a wide range of findings. Such broad
spectrum of investigations in a single report literature is lacking.
Based upon the model analysis, it is discovered that the highest
average severity level of the discomfort exists in neck, shoulder, eyes,
shoulder joint/upper arm, upper back, low back and head etc. The
biggest weekly changes of discomfort rates are in eyes, neck, head,
shoulder, shoulder joint/upper arm and upper back etc. The fastest
discomfort rate is found in neck, followed by shoulder, eyes, head,
shoulder joint/upper arm and upper back etc. Most of our findings are
consistent with the literature, which demonstrates that the developed
model and results are applicable and valuable and can be utilized to
assess correlation between the amount of computer-related workload
and health risk.
Abstract: Thermodynamics characterization Sesame oil
extraction by Acetone, Hexane and Benzene has been evaluated. The
120 hours experimental Data were described by a simple
mathematical model. According to the simulation results and the
essential criteria, Acetone is superior to other solvents but under
certain conditions where oil extraction takes place Hexane is superior
catalyst.
Abstract: In this work, we present a reliable framework to solve boundary value problems with particular significance in solid mechanics. These problems are used as mathematical models in deformation of beams. The algorithm rests mainly on a relatively new technique, the Variational Iteration Method. Some examples are given to confirm the efficiency and the accuracy of the method.