Abstract: A mathematical model based on a mass and energy
balance for the combustion in a cement rotary kiln was developed.
The model was used to investigate the impact of replacing about
45 % of the primary coal energy by different alternative fuels.
Refuse derived fuel, waste wood, solid hazardous waste and liquid
hazardous waste were used in the modeling. The results showed that
in order to keep the kiln temperature unchanged, and thereby
maintain the required clinker quality, the production capacity had to
be reduced by 1-15 %, depending on the fuel type. The reason for the
reduction is increased exhaust gas flow rates caused by the fuel
characteristics. The model, which has been successfully validated in a
full-scale experiment, was also used to show that the negative impact
on the production capacity can be avoided if a relatively small part of
the combustion air is replaced by pure oxygen.
Abstract: Markov games can be effectively used to design
controllers for nonlinear systems. The paper presents two novel
controller design algorithms by incorporating ideas from gametheory
literature that address safety and consistency issues of the
'learned' control strategy. A more widely used approach for
controller design is the H∞ optimal control, which suffers from high
computational demand and at times, may be infeasible. We generate
an optimal control policy for the agent (controller) via a simple
Linear Program enabling the controller to learn about the unknown
environment. The controller is facing an unknown environment and
in our formulation this environment corresponds to the behavior rules
of the noise modeled as the opponent. Proposed approaches aim to
achieve 'safe-consistent' and 'safe-universally consistent' controller
behavior by hybridizing 'min-max', 'fictitious play' and 'cautious
fictitious play' approaches drawn from game theory. We empirically
evaluate the approaches on a simulated Inverted Pendulum swing-up
task and compare its performance against standard Q learning.
Abstract: Variational methods for optical flow estimation are
known for their excellent performance. The method proposed by Brox
et al. [5] exemplifies the strength of that framework. It combines
several concepts into single energy functional that is then minimized
according to clear numerical procedure. In this paper we propose
a modification of that algorithm starting from the spatiotemporal
gradient constancy assumption. The numerical scheme allows to
establish the connection between our model and the CLG(H) method
introduced in [18]. Experimental evaluation carried out on synthetic
sequences shows the significant superiority of the spatial variant of
the proposed method. The comparison between methods for the realworld
sequence is also enclosed.
Abstract: The way music is interpreted by the human brain is a very interesting topic, but also an intricate one. Although this domain has been studied for over a century, many gray areas remain in the understanding of music. Recent advances have enabled us to perform accurate measurements of the time taken by the human brain to interpret and assimilate a sound. Cognitive computing provides tools and development environments that facilitate human cognition simulation. ACT-R is a cognitive architecture which offers an environment for implementing human cognitive tasks. This project combines our understanding of the music interpretation by a human listener and the ACT-R cognitive architecture to build SINGER, a computerized simulation for listening and recalling songs. The results are similar to human experimental data. Simulation results also show how it is easier to remember short melodies than long melodies which require more trials to be recalled correctly.
Abstract: This work presents a methodology for the design and
manufacture of propellers oriented to the experimental verification of
theoretical results based on the combined model. The design process
begins by using algorithms in Matlab which output data contain the
coordinates of the points that define the blade airfoils, in this case the
NACA 6512 airfoil was used. The modeling for the propeller blade
was made in NX7, through the imported files in Matlab and with the
help of surfaces. Later, the hub and the clamps were also modeled.
Finally, NX 7 also made possible to create post-processed files to the
required machine. It is possible to find the block of numbers with G
& M codes about the type of driver on the machine. The file
extension is .ptp. These files made possible to manufacture the blade,
and the hub of the propeller.
Abstract: A strategy is implemented to find the improved configuration design of an existing aircraft structure by executing topology and shape optimizations. Structural analysis of the Initial Design Space is performed in ANSYS under the loads pertinent to operating and ground conditions. By using the FEA results and data, an initial optimized layout configuration is attained by exploiting nonparametric topology optimization in TOSCA software. Topological optimized surfaces are then smoothened and imported in ANSYS to develop the geometrical features. Nodes at the critical locations of resulting voids are selected for sketching rough profiles. Rough profiles are further refined and CAD feasible geometric features are generated. The modified model is then analyzed under the same loadings and constraints as defined for topology optimization. Shape at the peak stress concentration areas are further optimized by exploiting the shape optimization in TOSCA.shape module. The harmonized stressed model with the modified surfaces is then imported in CATIA to develop the final design.
Abstract: Earthquakes are natural phenomena that occur with influence of a lot of parameters such as seismic activity, changing in the ground waters' motion, changing in the water-s temperature, etc. On the other hand, the radon gas concentrations in soil vary as nonlinear generally with earthquakes. Continuous measurement of the soil radon gas is very important for determination of characteristic of the seismic activity. The radon gas changes as continuous with strain occurring within the Earth-s surface during an earthquake and effects from the physical and the chemical processes such as soil structure, soil permeability, soil temperature, the barometric pressure, etc. Therefore, at the modeling researches are notsufficient to knowthe concentration ofradon gas. In this research, we determined relationships between radon emissions based on the environmental parameters and earthquakes occurring along the East Anatolian Fault Zone (EAFZ), Turkiye and predicted magnitudes of some earthquakes with the artificial neural network (ANN) model.
Abstract: Nowaday-s, many organizations use systems that
support business process as a whole or partially. However, in some
application domains, like software development and health care
processes, a normative Process Aware System (PAS) is not suitable,
because a flexible support is needed to respond rapidly to new
process models. On the other hand, a flexible Process Aware System
may be vulnerable to undesirable and fraudulent executions, which
imposes a tradeoff between flexibility and security. In order to make
this tradeoff available, a genetic-based anomaly detection model for
logs of Process Aware Systems is presented in this paper. The
detection of an anomalous trace is based on discovering an
appropriate process model by using genetic process mining and
detecting traces that do not fit the appropriate model as anomalous
trace; therefore, when used in PAS, this model is an automated
solution that can support coexistence of flexibility and security.
Abstract: In this paper, the American exchange option (AEO) valuation problem is modelled as a free boundary problem. The critical stock price for an AEO is satisfied an integral equation implicitly. When the remaining time is large enough, an asymptotic formula is provided for pricing an AEO. The numerical results reveal that our asymptotic pricing formula is robust and accurate for the long-term AEO.
Abstract: Understanding patient factors related to physical activity behavior is important in the management of Type 2 Diabetes. This study applied the Theory of Planned Behavior model to understand physical activity behavior among sampled Type 2 diabetics in Kenya. The study was conducted within the diabetic clinic at Kisii Level 5 Hospital and adopted sequential mixed methods design beginning with qualitative phase and ending with quantitative phase. Qualitative data was analyzed using grounded theory analysis method. Structural equation modeling using maximum likelihood was used to analyze quantitative data. The common fit indices revealed that the theory of planned behavior fitted the data acceptably well among the Type 2 diabetes and within physical activity behavior {¤ç2 = 213, df = 84, n=230, p = .061, ¤ç2/df = 2.53; TLI = .97; CFI =.96; RMSEA (90CI) = .073(.029, .08)}. This theory proved to be useful in understanding physical activity behavior among Type 2 diabetics.
Abstract: This paper presents the system identification by
physical-s law method and designs the controller for the Azimuth
Angle Control of the Platform of the Multi-Launcher Rocket System
(MLRS) by Root Locus technique. The plant mathematical model
was approximated using MATLAB for simulation and analyze the
system. The controller proposes the implementation of PID
Controller using Programmable Logic Control (PLC) for control the
plant. PID Controllers are widely applicable in industrial sectors and
can be set up easily and operate optimally for enhanced productivity,
improved quality and reduce maintenance requirement. The results
from simulation and experiments show that the proposed a PID
Controller to control the elevation angle that has superior control
performance by the setting time less than 12 sec, the rise time less
than 1.6 sec., and zero steady state. Furthermore, the system has a
high over shoot that will be continue development.
Abstract: Simulation accuracy by recent dynamic vehicle
simulation multidimensional expression significantly has progressed
and acceptable results not only for passive vehicles but also for
active vehicles normally equipped with advanced electronic
components is also provided. Recently, one of the subjects that has it
been considered, is increasing the safety car in design. Therefore,
many efforts have been done to increase vehicle stability especially
in the turn. One of the most important efforts is adjusting the camber
angle in the car suspension system. Optimum control camber angle in
addition to the vehicle stability is effective in the wheel adhesion on
road, reducing rubber abrasion and acceleration and braking. Since
the increase or decrease in the camber angle impacts on the stability
of vehicles, in this paper, a car suspension system mechanism is
introduced that could be adjust camber angle and the mechanism is
application and also inexpensive. In order to reach this purpose, in
this paper, a passive double wishbone suspension system with
variable camber angle is introduced and then variable camber
mechanism designed and analyzed for study the designed system
performance, this mechanism is modeled in Visual Nastran software
and kinematic analysis is revealed.
Abstract: This paper introduces a mixed integer programming model to find the optimum development plan for port Anzali. The model minimizes total system costs taking into account both port infrastructure costs and shipping costs. Due to the multipurpose function of the port, the model consists of 1020 decision variables and 2490 constraints. Results of the model determine the optimum number of berths that should be constructed in each period and for each type of cargo. In addition to, the results of sensitivity analysis on port operation quantity provide useful information for managers to choose the best scenario for port planning with the lowest investment risks. Despite all limitations-due to data availability-the model offers a straightforward decision tools to port planners aspiring to achieve optimum port planning steps.
Abstract: For about two decades scientists have been
developing techniques for enhancing the quality of medical images
using Fourier transform, DWT (Discrete wavelet transform),PDE
model etc., Gabor wavelet on hexagonal sampled grid of the images
is proposed in this work. This method has optimal approximation
theoretic performances, for a good quality image. The computational
cost is considerably low when compared to similar processing in the
rectangular domain. As X-ray images contain light scattered pixels,
instead of unique sigma, the parameter sigma of 0.5 to 3 is found to
satisfy most of the image interpolation requirements in terms of high
Peak Signal-to-Noise Ratio (PSNR) , lower Mean Squared Error
(MSE) and better image quality by adopting windowing technique.
Abstract: The performance of Advection Upstream Splitting
Method AUSM schemes are evaluated against experimental flow
fields at different Mach numbers and results are compared with
experimental data of subsonic, supersonic and hypersonic flow fields.
The turbulent model used here is SST model by Menter. The
numerical predictions include lift coefficient, drag coefficient and
pitching moment coefficient at different mach numbers and angle of
attacks. This work describes a computational study undertaken to
compute the Aerodynamic characteristics of different air vehicles
configurations using a structured Navier-Stokes computational
technique. The CFD code bases on the idea of upwind scheme for the
convective (convective-moving) fluxes. CFD results for GLC305
airfoil and cone cylinder tail fined missile calculated on above
mentioned turbulence model are compared with the available data.
Wide ranges of Mach number from subsonic to hypersonic speeds are
simulated and results are compared. When the computation is done
by using viscous turbulence model the above mentioned coefficients
have a very good agreement with the experimental values. AUSM
scheme is very efficient in the regions of very high pressure gradients
like shock waves and discontinuities. The AUSM versions simulate
the all types of flows from lower subsonic to hypersonic flow without
oscillations.
Abstract: This study deals with a multi-criteria optimization
problem which has been transformed into a single objective
optimization problem using Response Surface Methodology (RSM),
Artificial Neural Network (ANN) and Grey Relational Analyses
(GRA) approach. Grey-RSM and Grey-ANN are hybrid techniques
which can be used for solving multi-criteria optimization problem.
There have been two main purposes of this research as follows.
1. To determine optimum and robust fiber dyeing process
conditions by using RSM and ANN based on GRA,
2. To obtain the best suitable model by comparing models
developed by different methodologies.
The design variables for fiber dyeing process in textile are
temperature, time, softener, anti-static, material quantity, pH,
retarder, and dispergator. The quality characteristics to be evaluated
are nominal color consistency of fiber, maximum strength of fiber,
minimum color of dyeing solution. GRA-RSM with exact level
value, GRA-RSM with interval level value and GRA-ANN models
were compared based on GRA output value and MSE (Mean Square
Error) performance measurement of outputs with each other. As a
result, GRA-ANN with interval value model seems to be suitable
reducing the variation of dyeing process for GRA output value of the
model.
Abstract: Multirate multimedia delivery applications in multihop Wireless Mesh Network (WMN) are data redundant and delay-sensitive, which brings a lot of challenges for designing efficient transmission systems. In this paper, we propose a new cross layer resource allocation scheme to minimize the receiver side distortion within the delay bound requirements, by exploring application layer Position and Value (P-V) diversity as well as the multihop Effective Capacity (EC). We specifically consider image transmission optimization here. First of all, the maximum supportable source traffic rate is identified by exploring the multihop Effective Capacity (EC) model. Furthermore, the optimal source coding rate is selected according to the P-V diversity of multirate media streaming, which significantly increases the decoded media quality. Simulation results show the proposed approach improved media quality significantly compared with traditional approaches under the same QoS requirements.
Abstract: This paper presents the modeling and simulation of a hybrid proton exchange membrane fuel cell (PEMFC) with an energy storage system for use in a stand-alone distributed generation (DG) system. The simulation model consists of fuel cell DG, lead-acid battery, maximum power point tracking and power conditioning unit which is modeled in the MATLAB/Simulink platform. Poor loadfollowing characteristics and slow response to rapid load changes are some of the weaknesses of PEMFC because of the gas processing reaction and the fuel cell dynamics. To address the load-tracking issues in PEMFC, a hybrid PEMFC and battery storage system is considered and modelled. The model utilizes PEMFC as the main energy source whereas the battery functions as energy storage to compensate for the limitations of PEMFC.Simulation results are given to show the overall system performance under light and heavyloading conditions.
Abstract: Charging and discharging phenomenon on the surface
of materials can be found in plasma display panel, spacecraft
charging, high voltage insulator, etc. This report gives a simple
explanation on this phenomenon. A scanning electron microscope
was used not only as a tool to produce energetic electron beam to
charge an insulator without metallic coating and to produce a surface
discharging (surface breakdown/flashover) but also to observe the
visible charging and discharging on the sample surface. A model of
electric field distribution on the surface was developed in order to
explain charging and discharging phenomena. Since charging and
discharging process involves incubation time, therefore this process
can be used to evaluate the insulation property of materials under
electron bombardment.
Abstract: Since IEC61850 substation communication standard represents the trend to develop new generations of Substation Automation System (SAS), many IED manufacturers pursue this technique and apply for KEMA. In order to put on the market to meet customer demand as fast as possible, manufacturers often apply their products only for basic environment standard certification but claim to conform to IEC61850 certification. Since verification institutes generally perform verification tests only on specific IEDs of the manufacturers, the interoperability between all certified IEDs cannot be guaranteed. Therefore the interoperability between IEDs from different manufacturers needs to be tested. Based upon the above reasons, this study applies the definitions of the information models, communication service, GOOSE functionality and Substation Configuration Language (SCL) of the IEC61850 to build the concept of communication protocols, and build the test environment. The procedures of the test of the data collection and exchange of the P2P communication mode and Client / Server communication mode in IEC61850 are outlined as follows. First, test the IED GOOSE messages communication capability from different manufacturers. Second, collect IED data from each IED with SCADA system and use HMI to display the SCADA platform. Finally, problems generally encountered in the test procedure are summarized.