Abstract: This paper deals with the experimental investigations
of the in-cylinder tumble flows in an unfired internal combustion
engine with a flat piston at the engine speeds ranging from 400 to
1000 rev/min., and also with the dome and dome-cavity pistons at an
engine speed of 1000 rev/min., using particle image velocimetry.
From the two-dimensional in-cylinder flow measurements, tumble
flow analysis is carried out in the combustion space on a vertical
plane passing through cylinder axis. To analyze the tumble flows,
ensemble average velocity vectors are used and to characterize it,
tumble ratio is estimated. From the results, generally, we have found
that tumble ratio varies mainly with crank angle position. Also, at the
end of compression stroke, average turbulent kinetic energy is more
at higher engine speeds. We have also found that, at 330 crank angle
position, flat piston shows an improvement of about 85 and 23% in
tumble ratio, and about 24 and 2.5% in average turbulent kinetic
energy compared to dome and dome-cavity pistons respectively
Abstract: Each new semiconductor technology node
brings smaller transistors and wires. Although this makes
transistors faster, wires get slower. In nano-scale regime, the
standard copper (Cu) interconnect will become a major hurdle
for FPGA interconnect due to their high resistivity and
electromigration. This paper presents the comprehensive
evaluation of mixed CNT bundle interconnects and
investigates their prospects as energy efficient and high speed
interconnect for future FPGA routing architecture. All
HSPICE simulations are carried out at operating frequency of
1GHz and it is found that mixed CNT bundle implemented in
FPGAs as interconnect can potentially provide a substantial
delay and energy reduction over traditional interconnects at
32nm process technology.
Abstract: For the past couple of decades Weak signal detection
is of crucial importance in various engineering and scientific
applications. It finds its application in areas like Wireless
communication, Radars, Aerospace engineering, Control systems and
many of those. Usually weak signal detection requires phase sensitive
detector and demodulation module to detect and analyze the signal.
This article gives you a preamble to intrusion detection system which
can effectively detect a weak signal from a multiplexed signal. By
carefully inspecting and analyzing the respective signal, this
system can successfully indicate any peripheral intrusion. Intrusion
detection system (IDS) is a comprehensive and easy approach
towards detecting and analyzing any signal that is weakened and
garbled due to low signal to noise ratio (SNR). This approach
finds significant importance in applications like peripheral security
systems.
Abstract: Computer technology and the Internet have made a
breakthrough in the existence of data communication. This has
opened a whole new way of implementing steganography to ensure
secure data transfer. Steganography is the fine art of hiding the
information. Hiding the message in the carrier file enables the
deniability of the existence of any message at all. This paper designs
a stego machine to develop a steganographic application to hide data
containing text in a computer video file and to retrieve the hidden
information. This can be designed by embedding text file in a video
file in such away that the video does not loose its functionality using
Least Significant Bit (LSB) modification method. This method
applies imperceptible modifications. This proposed method strives
for high security to an eavesdropper-s inability to detect hidden
information.
Abstract: The paper describes the carbonate microfacies identified in the Sinjar Formation (Late Paleocene–Early Eocene) cropping out in Qara Dagh Mountain, near Sulekan Village approximately 20km south–west of Sulaimani (Iraq). One section (62m thick) has been measured in the field and closely sampled to undertake detailed microfaciesal and micropalaeontological studies to determine the formation-s age and environment of deposition. A samples were collected illustrating all the lithological changes along the section. The limestone in the studied area is hard and extremely rich in large foraminifers (soritids, rotaliids, nummulites, miliolids) and green algae (dasycladales). The investigation of the thin sections allowed us to identify the carbonate microfacies (18 types and subtypes) and the micropaleontological association (foraminifers and green algae), to determine the age of formation and to reconstruct the paleoenvironment of deposition (fore-reef, reef, back-reef). Based on the field observations and the studied thin sections, we determined three Units of a carbonate platform (I, II and III) from the base to the top of the section: Unit I with coralgal associations, Unit II is dominated by larger foraminifers and haracterized by the absence of coralgal associations, while Unit III is dominated by small foraminifers (mostly miliolids), peloids and green algae. It is partially dolomitized.
Abstract: This paper presents three new methodologies for the
basic operations, which aim at finding new ways of computing union
(maximum) and intersection (minimum) membership values by
taking into effect the entire membership values in a fuzzy set. The
new methodologies are conceptually simple and easy from the
application point of view and are illustrated with a variety of
problems such as Cartesian product of two fuzzy sets, max –min
composition of two fuzzy sets in different product spaces and an
application of an inverted pendulum to determine the impact of the
new methodologies. The results clearly indicate a difference based on
the nature of the fuzzy sets under consideration and hence will be
highly useful in quite a few applications where different values have
significant impact on the behavior of the system.
Abstract: Traditional development of wireless sensor network
mote is generally based on SoC1 platform. Such method of
development faces three main drawbacks: lack of flexibility in terms
of development due to low resource and rigid architecture of SoC;
low capability of evolution and portability versus performance if
specific micro-controller architecture features are used; and the rapid
obsolescence of micro-controller comparing to the long lifetime of
power plants or any industrial installations. To overcome these
drawbacks, we have explored a new approach of development of
wireless sensor network mote using a hybrid FPGA technology. The
application of such approach is illustrated through the
implementation of an innovative wireless sensor network protocol
called OCARI.
Abstract: Traditionally, wind tunnel models are made of metal
and are very expensive. In these years, everyone is looking for ways
to do more with less. Under the right test conditions, a rapid
prototype part could be tested in a wind tunnel. Using rapid prototype
manufacturing techniques and materials in this way significantly
reduces time and cost of production of wind tunnel models. This
study was done of fused deposition modeling (FDM) and their ability
to make components for wind tunnel models in a timely and cost
effective manner. This paper discusses the application of wind tunnel
model configuration constructed using FDM for transonic wind
tunnel testing. A study was undertaken comparing a rapid
prototyping model constructed of FDM Technologies using
polycarbonate to that of a standard machined steel model. Testing
covered the Mach range of Mach 0.3 to Mach 0.75 at an angle-ofattack
range of - 2° to +12°. Results from this study show relatively
good agreement between the two models and rapid prototyping
Method reduces time and cost of production of wind tunnel models.
It can be concluded from this study that wind tunnel models
constructed using rapid prototyping method and materials can be
used in wind tunnel testing for initial baseline aerodynamic database
development.
Abstract: Autofluorescence (AF) bronchoscopy is an
established method to detect dysplasia and carcinoma in situ (CIS).
For this reason the “Sotiria" Hospital uses the Karl Storz D-light
system. However, in early tumor stages the visualization is not that
obvious. With the help of a PC, we analyzed the color images we
captured by developing certain tools in Matlab®. We used statistical
methods based on texture analysis, signal processing methods based
on Gabor models and conversion algorithms between devicedependent
color spaces. Our belief is that we reduced the error made
by the naked eye. The tools we implemented improve the quality of
patients' life.
Abstract: Nowadays, the focus on renewable energy and alternative fuels has increased due to increasing oil prices, environment pollution, and also concern on preserving the nature. Biodiesel has been known as an attractive alternative fuel although biodiesel produced from edible oil is very expensive than conventional diesel. Therefore, the uses of biodiesel produced from non-edible oils are much better option. Currently Jatropha biodiesel (JBD) is receiving attention as an alternative fuel for diesel engine. Biodiesel is non-toxic, biodegradable, high lubricant ability, highly renewable, and its use therefore produces real reduction in petroleum consumption and carbon dioxide (CO2) emissions. Although biodiesel has many advantages, but it still has several properties need to improve, such as lower calorific value, lower effective engine power, higher emission of nitrogen oxides (NOX) and greater sensitivity to low temperature. Exhaust gas recirculation (EGR) is effective technique to reduce NOX emission from diesel engines because it enables lower flame temperature and oxygen concentration in the combustion chamber. Some studies succeeded to reduce the NOX emission from biodiesel by EGR but they observed increasing soot emission. The aim of this study was to investigate the engine performance and soot emission by using blended Jatropha biodiesel with different EGR rates. A CI engine that is water-cooled, turbocharged, using indirect injection system was used for the investigation. Soot emission, NOX, CO2, carbon monoxide (CO) were recorded and various engine performance parameters were also evaluated.
Abstract: The present study examines the adsorption of phenol, 3-nitrophenol and dyes (methylene blue, alizarine yellow), from aqueous solutions onto a commercial activated carbon. Two different operations, semi-batch and continuous with reflux, were applied. The commercial activated carbon exhibits high adsorption abilities for phenol, 3-nitrophenol and dyes (methylene blue and alizarin yellow) from their aqueous solutions. The adsorption of all adsorbates after 1 h is higher by the continuous operation with reflux than by the semibatch operation. The adsorption of phenol is higher than that of 3-nitrophenol for both operations. Similarly, the adsorption of alizarin yellow is higher than that of methylene blue for both operations. The regenerated commercial activated carbon regains its adsorption ability due to the removal of the adsorbate from its pores during the regeneration.
Abstract: In this study, a new procedure for inspecting damages on LNG storage tanks was proposed with the use of structural diagnostic techniques: i.e., nondestructive inspection techniques such as macrography, the hammer sounding test, the Schmidt hammer test, and the ultrasonic pulse velocity test, and destructive inspection techniques such as the compressive strength test, the chloride penetration test, and the carbonation test. From the analysis of all the test results, it was concluded that the LNG storage tank cover was in good condition. Such results were also compared with the Korean concrete standard specifications and design values. In addition, the remaining life of the LNG storage tank was estimated by using existing models. Based on the results, an LNG storage tank cover performance evaluation procedure was suggested.
Abstract: Carbonic anhydrases (CAs) has been focused as
biological catalysis for CO2 sequestration process because it can
catalyze the conversion of CO2 to bicarbonate. Here, codon-optimized
sequence of α type-CA cloned from Duneliala species. (DsCAopt) was
constructed, expressed, and characterized. The expression level in E.
coli BL21(DE3) was better for codon-optimized DsCAopt than intact
sequence of DsCAopt. DsCAopt enzyme shows high-stability at pH
7.6/10.0. In final, we demonstrated that in the Ca2+ solution, DsCAopt
enzyme can catalyze well the conversion of CO2 to CaCO3, as the
calcite form.
Abstract: Multimedia security is an incredibly significant area
of concern. A number of papers on robust digital watermarking have
been presented, but there are no standards that have been defined so
far. Thus multimedia security is still a posing problem. The aim of
this paper is to design a robust image-watermarking scheme, which
can withstand a different set of attacks. The proposed scheme
provides a robust solution integrating image moment normalization,
content dependent watermark and discrete wavelet transformation.
Moment normalization is useful to recover the watermark even in
case of geometrical attacks. Content dependent watermarks are a
powerful means of authentication as the data is watermarked with its
own features. Discrete wavelet transforms have been used as they
describe image features in a better manner. The proposed scheme
finds its place in validating identification cards and financial
instruments.
Abstract: In this paper a study on the vibration of thin
cylindrical shells with ring supports and made of functionally graded
materials (FGMs) composed of stainless steel and nickel is presented.
Material properties vary along the thickness direction of the shell
according to volume fraction power law. The cylindrical shells have
ring supports which are arbitrarily placed along the shell and impose
zero lateral deflections. The study is carried out based on third order
shear deformation shell theory (T.S.D.T). The analysis is carried out
using Hamilton-s principle. The governing equations of motion of
FGM cylindrical shells are derived based on shear deformation
theory. Results are presented on the frequency characteristics,
influence of ring support position and the influence of boundary
conditions. The present analysis is validated by comparing results
with those available in the literature.
Abstract: In the present study, a numerical analysis is carried
out to investigate unsteady MHD (magneto-hydrodynamic) flow and
heat transfer of a non-Newtonian second grade viscoelastic fluid
over an oscillatory stretching sheet. The flow is induced due to an
infinite elastic sheet which is stretched oscillatory (back and forth) in
its own plane. Effect of viscous dissipation and joule heating are
taken into account. The non-linear differential equations governing
the problem are transformed into system of non-dimensional
differential equations using similarity transformations. A newly
developed meshfree numerical technique Element free Galerkin
method (EFGM) is employed to solve the coupled non linear
differential equations. The results illustrating the effect of various
parameters like viscoelastic parameter, Hartman number, relative
frequency amplitude of the oscillatory sheet to the stretching rate and
Eckert number on velocity and temperature field are reported in
terms of graphs and tables. The present model finds its application in
polymer extrusion, drawing of plastic films and wires, glass, fiber
and paper production etc.
Abstract: Steroidal hormones with the efficient changes on the epiphyseal growth plate may influence tissue structure properties. Presents paper to investigate the effects of gonadectomy in the pattern distribution of the epiphyseal structure. Fifteen adult female New Zealand white rabbits were separated into three groups. One group was intact and others groups were selected for surgical operation. From these two groups, one group carried out steroidal administration. The results obtained showed that there is no statistically difference in the mean diameter of the growth plate cells between all three groups. The maximum value of the cartilage cells were allocated to the gonadectomized group and the minimum number were observed in Hormonal induced group significantly. Growth plate height was significantly greater in gonadectomized group than in two other groups.
Abstract: Our objective in this paper is to propose an approach
capable of clustering web messages. The clustering is carried out by
assigning, with a certain probability, texts written by the same web
user to the same cluster based on Stylometric features and using
fuzzy clustering algorithms. Focus in the present work is on
comparing the most popular algorithms in fuzzy clustering theory
namely, Fuzzy C-means, Possibilistic C-means and Fuzzy
Possibilistic C-Means.
Abstract: As the resources for naturally occurring aggregates
diminished at an ever increasing rate, researchers are keen to utilize
recycled materials in road construction in harmony with sustainable
development. Steel slag, a waste product from the steel making
industry, is one of the recycled materials reported to exhibit great
potential to replace naturally occurring aggregates in asphalt
mixtures. This paper presents the resilient modulus properties of
steel slag asphalt mixtures subjected to short term oven ageing
(STOA). The resilient modulus test was carried out to evaluate the
stiffness of asphalt mixtures at 10ºC, 25ºC and 40ºC. Previous
studies showed that stiffness changes in asphalt mixture played an
important role in inflicting pavement distress particularly cracking
and rutting that are common at low and high temperatures
respectively. Temperature was found to significantly influence the
resilient modulus of asphalt mixes. The resilient modulus of the
asphalt specimens tested decreased by more than 90% when the test
temperature increased from 10°C to 40°C.
Abstract: It is well known that surface enhancements play an important role in augmenting the thermal performance of flat plate solar collector. In this paper, an attempt is made to explain in a comparative way the effect of surface geometry of solar collector having dimple geometry with that of a flat plate solar collector of the same size. A CFD analysis was carried out for the two cases, subjected to a constant heat flux of 600W/m2 and 1000W/m2. It can be inferred from the study that the absorber plate temperature shows a rise of average surface temperature of about 50C for the dimple solar collector when compared to a flat plate solar collector. Most importantly, the average exit water temperature shows a marked improvement of about 5.50C for a dimple solar collector as compared to that of a flat plate solar collector.