Abstract: Magnesium alloys have gained increased attention in recent years in automotive, electronics, and medical industry. This because of magnesium alloys have better properties than aluminum alloys and steels in respects of their low density and high strength to weight ratio. However, the main problems of magnesium alloy welding are the crack formation and the appearance of porosity during the solidification. This paper proposes a unique technique to weld two thin sheets of AZ31B magnesium alloy using a paste containing Ag nanoparticles. The paste containing Ag nanoparticles of 5 nm in average diameter and an organic solvent was used to coat the surface of AZ31B thin sheet. The coated sheet was heated at 100 °C for 60 s to evaporate the solvent. The dried sheet was set as a lower AZ31B sheet on the jig, and then lap fillet welding was carried out by using a pulsed Nd:YAG laser in a closed box filled with argon gas. The characteristics of the microstructure and the corrosion behavior of the joints were analyzed by opticalmicroscopy (OM), energy dispersive spectrometry (EDS), electron probe micro-analyzer (EPMA), scanning electron microscopy (SEM), and immersion corrosion test. The experimental results show that the wrought AZ31B magnesium alloy can be joined successfully using Ag nanoparticles. Ag nanoparticles insert promote grain refinement, narrower the HAZ width and wider bond width compared to weld without and insert. Corrosion rate of welded AZ31B with Ag nanoparticles reduced up to 44 % compared to base metal. The improvement of corrosion resistance of welded AZ31B with Ag nanoparticles due to finer grains and large grain boundaries area which consist of high Al content. β-phase Mg17Al12 could serve as effective barrier and suppressed further propagation of corrosion. Furthermore, Ag distribution in fusion zone provide much more finer grains and may stabilize the magnesium solid solution making it less soluble or less anodic in aqueous
Abstract: E-tailing websites are often perceived to be static, impersonal and distant. However, with the movement of the World Wide Web to Web 2.0 in recent years, these online websites have been found to display personalities akin to 'humanistic' qualities and project impressions much like its retailing counterpart i.e. salespeople. This paper examines the personality of e-tailing websites and their impact on consumers- initial trust towards the sites. A total of 239 Internet users participated in this field experiment study which utilized 6 online book retailers- websites that the participants had not previously visited before. Analysis revealed that out of four website personalities (sincerity, competence, excitement and sophistication) only sincerity and competence are able to exert an influence in building consumers- trust upon their first visit to the website. The implications of the findings are further elaborated in this paper.
Abstract: Nowadays, quasi-continuous wave diode lasers are
used in a widespread variety of applications. Temperature effects in
these lasers can strongly influence their performance. In this paper,
the effects of temperature have been experimentally investigated on
different features of a 60W-QCW diode laser. The obtained results
indicate that the conversion efficiency and operation voltage of diode
laser decrease with the augmentation of the working temperature
associated with a redshift in the laser peak wavelength. Experimental
results show the emission peak wavelength of laser shifts 0.26 nm
and the conversion efficiency decreases 1.76 % with the increase of
temperature from 40 to 50 ̊C. Present study also shows the slope
efficiency decreases gradually at low temperatures and rapidly at
higher temperatures. Regarding the close dependence of the
mentioned parameters to the operating temperature, it is of great
importance to carefully control the working temperature of diode
laser, particularly for medical applications.
Abstract: For the communication between human and computer
in an interactive computing environment, the gesture recognition is
studied vigorously. Therefore, a lot of studies have proposed efficient
methods about the recognition algorithm using 2D camera captured
images. However, there is a limitation to these methods, such as the
extracted features cannot fully represent the object in real world.
Although many studies used 3D features instead of 2D features for
more accurate gesture recognition, the problem, such as the processing
time to generate 3D objects, is still unsolved in related researches.
Therefore we propose a method to extract the 3D features combined
with the 3D object reconstruction. This method uses the modified
GPU-based visual hull generation algorithm which disables unnecessary
processes, such as the texture calculation to generate three kinds
of 3D projection maps as the 3D feature: a nearest boundary, a farthest
boundary, and a thickness of the object projected on the base-plane. In
the section of experimental results, we present results of proposed
method on eight human postures: T shape, both hands up, right hand
up, left hand up, hands front, stand, sit and bend, and compare the
computational time of the proposed method with that of the previous
methods.
Abstract: The present work consecutively on synthesis and
characterization of composites, Al/Al alloy A 384.1 as matrix in
which the main ingredient as Al/Al-5% MgO alloy based metal
matrix composite. As practical implications the low cost processing
route for the fabrication of Al alloy A 384.1 and operational
difficulties of presently available manufacturing processes based in
liquid manipulation methods. As all new developments, complete
understanding of the influence of processing variables upon the final
quality of the product. And the composite is applied comprehensively
to the acquaintance for achieving superiority of information
concerning the specific heat measurement of a material through the
aid of thermographs. Products are evaluated concerning relative
particle size and mechanical behavior under tensile strength.
Furthermore, Taguchi technique was employed to examine the
experimental optimum results are achieved, owing to effectiveness of
this approach.
Abstract: This paper covers the present situation and problem of experimental teaching of mathematics specialty in recent years, puts
forward and demonstrates experimental teaching methods for different
education. From the aspects of content and experimental teaching
approach, uses as an example the course “Experiment for Program
Designing & Algorithmic Language" and discusses teaching practice
and laboratory course work. In addition a series of successful methods
and measures are introduced in experimental teaching.
Abstract: It is hard to percept the interaction process with machines when visual information is not available. In this paper, we have addressed this issue to provide interaction through visual techniques. Posture recognition is done for American Sign Language to recognize static alphabets and numbers. 3D information is exploited to obtain segmentation of hands and face using normal Gaussian distribution and depth information. Features for posture recognition are computed using statistical and geometrical properties which are translation, rotation and scale invariant. Hu-Moment as statistical features and; circularity and rectangularity as geometrical features are incorporated to build the feature vectors. These feature vectors are used to train SVM for classification that recognizes static alphabets and numbers. For the alphabets, curvature analysis is carried out to reduce the misclassifications. The experimental results show that proposed system recognizes posture symbols by achieving recognition rate of 98.65% and 98.6% for ASL alphabets and numbers respectively.
Abstract: Since the 1940s, many promising telepresence
research results have been obtained. However, telepresence
technology still has not reached industrial usage. As human
intelligence is necessary for successful execution of most manual
assembly tasks, the ability of the human is hindered in some cases,
such as the assembly of heavy parts of small/medium lots or
prototypes. In such a case of manual assembly, the help of industrial
robots is mandatory. The telepresence technology can be considered
as a solution for performing assembly tasks, where the human
intelligence and haptic sense are needed to identify and minimize the
errors during an assembly process and a robot is needed to carry
heavy parts. In this paper, preliminary steps to integrate the
telepresence technology into industrial robot systems are introduced.
The system described here combines both, the human haptic sense
and the industrial robot capability to perform a manual assembly task
remotely using a force feedback joystick. Mapping between the
joystick-s Degrees of Freedom (DOF) and the robot-s ones are
introduced. Simulation and experimental results are shown and future
work is discussed.
Abstract: Homogeneous Charge Compression (HCCI) Ignition technology has been around for a long time, but has recently received renewed attention and enthusiasm. This paper deals with experimental investigations of HCCI engine using hydrous methanol as a primary fuel and Dimethyl Ether (DME) as an ignition improver. A regular diesel engine has been modified to work as HCCI engine for this investigation. The hydrous methanol is inducted and DME is injected into a single cylinder engine. Hence, hydrous methanol is used with 15% water content in HCCI engine and its performance and emission behavior is documented. The auto-ignition of Methanol is enabled by DME. The quantity of DME varies with respect to the load. In this study, the experiments are conducted independently and the effect of the hydrous methanol on the engine operating limit, heat release rate and exhaust emissions at different load conditions are investigated. The investigation also proves that the Hydrous Methanol with DME operation reduces the oxides of Nitrogen and smoke to an extreme low level which is not possible by the direct injection CI engine. Therefore, it is beneficial to use hydrous methanol-DME HCCI mode while using hydrous methanol in internal Combustion Engines.
Abstract: This paper considers the problem of scheduling maintenance actions for identical aircraft gas turbine engines. Each one of the turbines consists of parts which frequently require replacement. A finite inventory of spare parts is available and all parts are ready for replacement at any time. The inventory consists of both new and refurbished parts. Hence, these parts have different field lives. The goal is to find a replacement part sequencing that maximizes the time that the aircraft will keep functioning before the inventory is replenished. The problem is formulated as an identical parallel machine scheduling problem where the minimum completion time has to be maximized. Two models have been developed. The first one is an optimization model which is based on a 0-1 linear programming formulation, while the second one is an approximate procedure which consists in decomposing the problem into several two-machine subproblems. Each subproblem is optimally solved using the first model. Both models have been implemented using Lingo and have been tested on two sets of randomly generated data with up to 150 parts and 10 turbines. Experimental results show that the optimization model is able to solve only instances with no more than 4 turbines, while the decomposition procedure often provides near-optimal solutions within a maximum CPU time of 3 seconds.
Abstract: The purpose of this study was to investigate the effect
of combining Real Experimentation (RE) With Virtual
Experimentation (VE) on students- conceptual understanding of
photo electric effect. To achieve this, a pre–post comparison study
design was used that involved 46 undergraduate students. Two
groups were set up for this study. Participants in the control group
used RE to learn photo electric effect, whereas, participants in the
experimental group used RE in the first part of the curriculum and
VE in another part. Achievement test was given to the groups
before and after the application as pre-test and post test. The
independent samples t- test, one way Anova and Tukey HSD test
were used for testing the data obtained from the study.
According to the results of analyzes, the experimental group
was found more successful than the control group.
Abstract: The aim of this paper is to develop a new two dimensional time accurate Euler solver for shock tube applications. The solver was developed to study the performance of a newly built short-duration hypersonic test facility at Universiti Tenaga Nasional “UNITEN" in Malaysia. The facility has been designed, built, and commissioned for different values of diaphragm pressure ratios in order to get wide range of Mach number. The developed solver uses second order accurate cell-vertex finite volume spatial discretization and forth order accurate Runge-Kutta temporal integration and it is designed to simulate the flow process for similar driver/driven gases (e.g. air-air as working fluids). The solver is validated against analytical solution and experimental measurements in the high speed flow test facility. Further investigations were made on the flow process inside the shock tube by using the solver. The shock wave motion, reflection and interaction were investigated and their influence on the performance of the shock tube was determined. The results provide very good estimates for both shock speed and shock pressure obtained after diaphragm rupture. Also detailed information on the gasdynamic processes over the full length of the facility is available. The agreements obtained have been reasonable.
Abstract: This paper presents the experimental results on effect of applied voltage stress frequency to the occurrence of electrical treeing in 22 kV cross linked polyethylene (XLPE) insulated cable.Hallow disk of XLPE insulating material with thickness 5 mm taken from unused high voltage cable was used as the specimen in this study. Stainless steel needle was inserted gradually into the specimen to give a tip to earth plane electrode separation of 2.50.2 mm at elevated temperature 105-110°C. The specimen was then annealed for 5 minute to minimize any mechanical stress build up around the needle-plane region before it was cooled down to room temperature. Each specimen were subjected to the same applied voltage stress level at 8 kV AC rms, with various frequency, 50, 100, 500, 1000 and 2000 Hz. Initiation time, propagation speed and pattern of electrical treeing were examined in order to study the effect of applied voltage stress frequency. By the experimental results, initial time of visible treeing decreases with increasing in applied voltage frequency. Also, obviously, propagation speed of electrical treeing increases with increasing in applied voltage frequency.Furthermore, two types of electrical treeing, bush-like and branch-like treeing were observed.The experimental results confirmed the effect of voltage stress frequency as well.
Abstract: In this paper, one-dimensional analysis of flow in a
single-stage gas gun is conducted. The compressible inviscid flow
equations are numerically solved by the second-order Roe TVD
method, by using moving boundaries. For investigation of real gas
effect the Noble-Able equation is applied. The numerical results are
compared with the experimental data to validate the numerical
scheme. The results show that with using the Noble-Able equation,
the muzzle velocity decreases.
Abstract: In this paper motion analysis on a winding
stair-climbing is investigated using our proposed rotational arm type
of robotic wheelchair. For now, the robotic wheelchair is operated in
an open mode to climb winding stairs by a dynamic turning, therefore,
the dynamics model is required to ensure a passenger-s safety.
Equations of motion based on the skid-steering analysis are developed
for the trajectory planning and motion analysis on climbing winding
stairs. Since the robotic wheelchair must climb a winding staircase
stably, the winding trajectory becomes a constraint equation to be
followed, and the Baumgarte-s method is used to solve for the
constrained dynamics equations. Experimental results validate the
behavior of the prototype as it climbs a winding stair.
Abstract: The main objectives of this study are to inspect and
identify any damage of jaimusi highway prestressed concrete bridge
after repair and strengthening of damaged structural members and to
evaluate the performance of the bridge structural members by
adopting static load test. Inspection program after repair and
strengthening includes identifying and evaluating the structural
members of bridge such as T-shape cantilever structure, hanging
beams, corbels, external tendons, anchor beams, sticking steel plate,
and piers. The results of inspection show that the overall state of the
bridge structural member after repair and strengthening is good. The
results of rebound test of concrete strength show that the average
strength of concrete is 46.31Mpa. Whereas, the average value of
concrete strength of anchor beam is 49.82Mpa. According to the
results of static load test, the experimental values are less than
theoretical values of internal forces, deflection, and strain, indicating
that the stiffness of the experimental structure, overall deformation
and integrity satisfy the designed standard and the working
performance is good, and the undertaking capacity has a certain
surplus. There is not visible change in the length and width of cracks
and there are not new cracks under experimental load.
Abstract: In this paper the fatigue crack initiation location of double shear lap joints, treated by interference fit and bolt clamping, have been investigated both experimentally and numerically. To do so, using the fracture section of available fatigue tested specimens of interference fitted and torque tightened Aluminum 2024-T3 plates, the crack initiation location was determined. The stress distribution attained from the finite element analysis was used to help explain the results observed in the experimental tests. The results showed that the fatigue crack initiation location changes from top and mid plane at the hole edge to somewhere far from the hole edge (stress concentration region) in different combination of clamping force, interference fit size and applied cyclic load ranges. It is worth mentioning that the fatigue crack initiation location affects the fatigue life of the specimens too.
Abstract: This paper presents the experiment results of investigating the effects of adding various types and proportions of fibre on mechanical strength and permeability characteristics of recycled aggregate concrete (RAC), which was produced with treated coarse recycled concrete aggregate (RCA). Two types of synthetic fibres (i.e., barchip and polypropylene fibre) with various volume fractions were added to the RAC, which was calculated by the weight of the cement. The hardened RAC properties such as compressive strength, flexural strength, ultrasonic pulse velocity, water absorption and total porosity at the curing ages of 7 and 28 days were evaluated and compared with the properties of the control specimens. Results indicate that the treated coarse RCA enhances the mechanical strength and permeability properties of RAC and adding barchip fibre further optimises the results. Adding 1.2% barchip fibre has the best effect on the mechanical strength performance of the RAC.
Abstract: A series of microarray experiments produces observations
of differential expression for thousands of genes across multiple
conditions.
Principal component analysis(PCA) has been widely used in
multivariate data analysis to reduce the dimensionality of the data in
order to simplify subsequent analysis and allow for summarization of
the data in a parsimonious manner. PCA, which can be implemented
via a singular value decomposition(SVD), is useful for analysis of
microarray data.
For application of PCA using SVD we use the DNA microarray
data for the small round blue cell tumors(SRBCT) of childhood
by Khan et al.(2001). To decide the number of components which
account for sufficient amount of information we draw scree plot.
Biplot, a graphic display associated with PCA, reveals important
features that exhibit relationship between variables and also the
relationship of variables with observations.
Abstract: Requirements are critical to system validation as they guide all subsequent stages of systems development. Inadequately specified requirements generate systems that require major revisions or cause system failure entirely. Use Cases have become the main vehicle for requirements capture in many current Object Oriented (OO) development methodologies, and a means for developers to communicate with different stakeholders. In this paper we present the results of a laboratory experiment that explored whether different types of use case format are equally effective in facilitating high knowledge user-s understanding. Results showed that the provision of diagrams along with the textual use case descriptions significantly improved user comprehension of system requirements in both familiar and unfamiliar application domains. However, when comparing groups that received models of textual description accompanied with diagrams of different level of details (simple and detailed) we found no significant difference in performance.