Abstract: Coal is an important non-renewable energy source of
and can be associated with radioactive elements. In Figueira city,
Paraná state, Brazil, it was recorded high uranium activity near the
coal mine that supplies a local thermoelectric power plant. In this
context, the radon activity (Rn-222, produced by the Ra-226 decay in
the U-238 natural series) was evaluated in groundwater, river water
and effluents produced from the acid mine drainage in the coal reject
dumps. The samples were collected in August 2013 and in February
2014 and analyzed at LABIDRO (Laboratory of Isotope and
Hydrochemistry), UNESP, Rio Claro city, Brazil, using an alpha
spectrometer (AlphaGuard) adjusted to evaluate the mean radon
activity concentration in five cycles of 10 minutes. No radon activity
concentration above 100 Bq.L-1, which was a previous critic value
established by the World Health Organization. The average radon
activity concentration in groundwater was higher than in surface
water and in effluent samples, possibly due to the accumulation of
uranium and radium in the aquifer layers that favors the radon
trapping. The lower value in the river waters can indicate dilution and
the intermediate value in the effluents may indicate radon absorption
in the coal particles of the reject dumps. The results also indicate that
the radon activities in the effluents increase with the sample
acidification, possibly due to the higher radium leaching and the
subsequent radon transport to the drainage flow. The water samples
of Laranjinha River and Ribeirão das Pedras stream, which,
respectively, supply Figueira city and receive the mining effluent,
exhibited higher pH values upstream the mine, reflecting the acid
mine drainage discharge. The radionuclides transport indicates the
importance of monitoring their activity concentration in natural
waters due to the risks that the radioactivity can represent to human
health.
Abstract: Grid is an environment with millions of resources
which are dynamic and heterogeneous in nature. A computational
grid is one in which the resources are computing nodes and is meant
for applications that involves larger computations. A scheduling
algorithm is said to be efficient if and only if it performs better
resource allocation even in case of resource failure. Resource
allocation is a tedious issue since it has to consider several
requirements such as system load, processing cost and time, user’s
deadline and resource failure. This work attempts in designing a
resource allocation algorithm which is cost-effective and also targets
at load balancing, fault tolerance and user satisfaction by considering
the above requirements. The proposed Budget Constrained Load
Balancing Fault Tolerant algorithm with user satisfaction (BLBFT)
reduces the schedule makespan, schedule cost and task failure rate
and improves resource utilization. Evaluation of the proposed
BLBFT algorithm is done using Gridsim toolkit and the results are
compared with the algorithms which separately concentrates on all
these factors. The comparison results ensure that the proposed
algorithm works better than its counterparts.
Abstract: An Australian manufacturer has fabricated an
innovative GFRP sandwich panel made from E-glass fiber skin and a
modified phenolic core for structural applications. Debonding, which
refers to separation of skin from the core material in composite
sandwiches, is one of the most common types of damage in
composites. The presence of debonding is of great concern because it
not only severely affects the stiffness but also modifies the dynamic
behaviour of the structure. Generally it is seen that the majority of
research carried out has been concerned about the delamination of
laminated structures whereas skin-core debonding has received
relatively minor attention. Furthermore it is observed that research
done on composite slabs having multiple skin-core debonding is very
limited. To address this gap, a comprehensive research investigating
dynamic behaviour of composite panels with single and multiple
debonding is presented. The study uses finite-element modelling and
analyses for investigating the influence of debonding on free
vibration behaviour of single and multilayer composite sandwich
panels. A broad parametric investigation has been carried out by
varying debonding locations, debonding sizes and support conditions
of the panels in view of both single and multiple debonding.
Numerical models were developed with Strand7 finite element
package by innovatively selecting the suitable elements to diligently
represent their actual behavior. Three-dimensional finite element
models were employed to simulate the physically real situation as
close as possible, with the use of an experimentally and numerically
validated finite element model. Comparative results and conclusions
based on the analyses are presented. For similar extents and locations
of debonding, the effect of debonding on natural frequencies appears
greatly dependent on the end conditions of the panel, giving greater
decrease in natural frequency when the panels are more restrained.
Some modes are more sensitive to debonding and this sensitivity
seems to be related to their vibration mode shapes. The fundamental
mode seems generally the least sensitive mode to debonding with
respect to the variation in free vibration characteristics. The results
indicate the effectiveness of the developed three dimensional finite
element models in assessing debonding damage in composite
sandwich panels.
Abstract: Availability of different genetic tests after completion
of Human Genome Project increases the physicians’ responsibility to
keep themselves update on the potential implementation of these
genetic tests in their daily practice. However, due to numbers of
barriers, still many of physicians are not either aware of these tests or
are not willing to offer or refer their patients for genetic tests. This
study was conducted an anonymous, cross-sectional, mailed-based
survey to develop a primary data of Malaysian physicians’ level of
knowledge and perception of gene profiling. Questionnaire had 29
questions. Total scores on selected questions were used to assess the
level of knowledge. The highest possible score was 11. Descriptive
statistics, one way ANOVA and chi-squared test was used for
statistical analysis. Sixty three completed questionnaires were
returned by 27 general practitioners (GPs) and 36 medical specialists.
Responders’ age ranges from 24 to 55 years old (mean 30.2 ± 6.4).
About 40% of the participants rated themselves as having poor level
of knowledge in genetics in general whilst 60% believed that they
have fair level of knowledge; however, almost half (46%) of the
respondents felt that they were not knowledgeable about available
genetic tests. A majority (94%) of the responders were not aware of
any lab or company which is offering gene profiling services in
Malaysia. Only 4% of participants were aware of using gene profiling
for detection of dosage of some drugs. Respondents perceived greater
utility of gene profiling for breast cancer (38%) compared to the
colorectal familial cancer (3%). The score of knowledge ranged from
2 to 8 (mean 4.38 ± 1.67). Non- significant differences between score
of knowledge of GPs and specialists were observed, with score of
4.19 and 4.58 respectively. There was no significant association
between any demographic factors and level of knowledge. However,
those who graduated between years 2001 to 2005 had higher level of
knowledge. Overall, 83% of participants showed relatively high level
of perception on value of gene profiling to detect patient’s risk of
disease. However, low perception was observed for both statements
of using gene profiling for general population in order to alter their
lifestyle (25%) as well as having the full sequence of a patient
genome for the purpose of determining a patient’s best match for
treatment (18%). The lack of clinical guidelines, limited provider
knowledge and awareness, lack of time and resources to educate
patients, lack of evidence-based clinical information and cost of tests
were the most barriers of ordering gene profiling mentioned by
physicians. In conclusion Malaysian physicians who participate in
this study had mediocre level of knowledge and awareness in gene
profiling. The low exposure to the genetic questions and problems
might be a key predictor of lack of awareness and knowledge on
available genetic tests. Educational and training workshop might be useful in helping Malaysian physicians incorporate genetic profiling
into practice for eligible patients.
Abstract: Coal fly ash is formed as a solid waste product from
the combustion of coal in coal fired power stations. Huge amounts of
fly ash are produced globally every year and are predicted to
increase. Nowadays, less than half of the fly ash is used as a raw
material for cement manufacturing, construction and the rest of it is
disposed as a waste causing yet another environmental concern. For
this reason, the recycling of this kind of slurries into useful materials
is quite important in terms of economical and environmental aspects.
The purpose of this study is to evaluate the Orhaneli and
Tuncbilek coal fly ashes for utilization in some industrial
applications. Therefore the mineralogical and chemical compositions
of these fly ashes were analyzed by X-ray fluorescence spectroscopy,
ourier-transform infrared spectrometer, and X-ray diffraction. The
silicon (Si) and aluminum (Al) in the fly ashes were activated by
alkali fusion technique with sodium hydroxide. The obtained extracts
were analyzed for Si and Al content by inductively coupled plasma
optical emission spectrometry.
Abstract: The following paper presents the results of a study
aimed at achieving a better understanding of the psychological
readiness for mobile learning (m-learning) among Saudi students,
while also evaluating m-learning readiness as a whole in Saudi
Arabia - a topic that has not yet received adequate attention from
researchers. Data was acquired via a questionnaire administered to
131 Saudi students at UK universities, in July 2013. The study
confirmed that students are confident about using mobile devices in
their daily lives, and that they would welcome more opportunities for
mobile learning. The findings also indicated that Saudi higher
education students are very familiar with, and psychologically ready
for, m-learning.
Abstract: The Aptima® HIV-1 Quant Dx Assay is a fully
automated assay on the Panther system. It is based on Transcription-
Mediated Amplification and real time detection technologies. This
assay is intended for monitoring HIV-1 viral load in plasma
specimens and for the detection of HIV-1 in plasma and serum
specimens.
Nine-hundred and seventy nine specimens selected at random
from routine testing at St Thomas’ Hospital, London were
anonymised and used to compare the performance of the Aptima
HIV-1 Quant Dx assay and Roche COBAS® AmpliPrep/COBAS®
TaqMan® HIV-1 Test, v2.0. Two-hundred and thirty four specimens
gave quantitative HIV-1 viral load results in both assays. The
quantitative results reported by the Aptima Assay were comparable to
those reported by the Roche COBAS AmpliPrep/COBAS TaqMan
HIV-1 Test, v2.0 with a linear regression slope of 1.04 and an
intercept on -0.097.
The Aptima assay detected HIV-1 in more samples than the
COBAS assay. This was not due to lack of specificity of the Aptima
assay because this assay gave 99.83% specificity on testing plasma
specimens from 600 HIV-1 negative individuals. To understand the
reason for this higher detection rate a side-by-side comparison of low
level panels made from the HIV-1 3rd international standard
(NIBSC10/152) and clinical samples of various subtypes were tested
in both assays. The Aptima assay was more sensitive than the
COBAS assay.
The good sensitivity, specificity and agreement with other
commercial assays make the HIV-1 Quant Dx Assay appropriate for
both viral load monitoring and detection of HIV-1 infections.
Abstract: Technology, multimedia in Open Educational
Resources, can contribute positively to student performance in an
online instructional environment. Student performance data of past
four years were obtained from an online course entitled Applied
Calculus (MA139). This paper examined the data to determine
whether multimedia (independent variable) had any impact on
student performance (dependent variable) in online math learning,
and how students felt about the value of the technology. Two groups
of student data were analyzed, group 1 (control) from the online
applied calculus course that did not use multimedia instructional
materials, and group 2 (treatment) of the same online applied calculus
course that used multimedia instructional materials. For the MA139
class, results indicate a statistically significant difference (p = .001)
between the two groups, where group 1 had a final score mean of
56.36 (out of 100), group 2 of 70.68. Additionally, student
testimonials were discussed in which students shared their experience
in learning applied calculus online with multimedia instructional
materials.
Abstract: 600 schools going adolescents and 100 teachers from
16 schools of Dhemaji and Lakhimpur district of Assam, India were
surveyed to assess and compare their awareness regarding AIDS and
AIDS Education. An awareness test was administered containing 38
items for adolescents and 40 items for teachers in the test.
Observations revealed that the majority of school-going adolescents
are poor in their HIV/AIDS and AIDS education awareness. It shows
that the school going adolescents of Dhemaji district are better in
HIV/AIDS and AIDS education awareness than the school going
adolescents of Lakhimpur district while comparing the gender,
settlement, steam and district wise variables.
Abstract: Image enhancement is a challenging issue in many applications. In the last two decades, there are various filters developed. This paper proposes a novel method which removes Gaussian noise from the gray scale images. The proposed technique is compared with Enhanced Fuzzy Peer Group Filter (EFPGF) for various noise levels. Experimental results proved that the proposed filter achieves better Peak-Signal-to-Noise-Ratio PSNR than the existing techniques. The proposed technique achieves 1.736dB gain in PSNR than the EFPGF technique.
Abstract: Chrome tannery wastewater causes serious environmental hazard due to its high pollution potential. As a result, rigorous treatment is necessary for abatement of pollution from this type of wastewater. There are many research studies on chrome tannery wastewater treatment in the field of physical, chemical, and biological methods. In general, biological treatment process is found ineffective for direct application because of adverse effects by toxic chromium, sulphide, chloride etc. However, biological methods were employed mainly for a few sub processes generating significant amount of organic matter and without chromium, chlorides etc. In this context the present paper reviews the characteristics feature and pollution potential of wastewater generated from chrome tannery units and treatment of the same. The different biological processes used earlier and their chronological development for treatment of the chrome tannery wastewater are thoroughly reviewed in this paper. In this regard, the scope of hybrid bioreactor - an advanced technology option has also been explored, as this kind of treatment is well suited for the wastewater having inhibitory substances.
Abstract: In this study, ultrasonic assisted machining (UAM) technique is applied in side-surface milling experiment for glass-ceramic workpiece material. The tungsten carbide cutting-tool with diamond coating is used in conjunction with two kinds of cooling/lubrication mediums such as water-soluble (WS) cutting fluid and minimum quantity lubricant (MQL). Full factorial process parameter combinations on the milling experiments are planned to investigate the effect of process parameters on cutting performance. From the experimental results, it tries to search for the better process parameter combination which the edge-indentation and the surface roughness are acceptable. In the machining experiments, ultrasonic oscillator was used to excite a cutting-tool along the radial direction producing a very small amplitude of vibration frequency of 20KHz to assist the machining process. After processing, toolmaker microscope was used to detect the side-surface morphology, edge-indentation and cutting tool wear under different combination of cutting parameters, and analysis and discussion were also conducted for experimental results. The results show that the main leading parameters to edge-indentation of glass ceramic are cutting depth and feed rate. In order to reduce edge-indentation, it needs to use lower cutting depth and feed rate. Water-soluble cutting fluid provides a better cooling effect in the primary cutting area; it may effectively reduce the edge-indentation and improve the surface morphology of the glass ceramic. The use of ultrasonic assisted technique can effectively enhance the surface finish cleanness and reduce cutting tool wear and edge-indentation.
Abstract: The principle of the seismic performance evaluation methods is to provide a measure of capability for a building or set of buildings to be damaged by an earthquake. The common objective of many of these methods is to supply classification criteria. The purpose of this study is to present a method for assessing the seismic performance of structures, based on Pushover method; we are particularly interested in reinforced concrete frame structures, which represent a significant percentage of damaged structures after a seismic event. The work is based on the characterization of seismic movement of the various earthquake zones in terms of PGA and PGD that is obtained by means of SIMQK_GR and PRISM software and the correlation between the points of performance and the scalar characterizing the earthquakes will developed.
Abstract: Introduction: Researchers globally have strived to explore diverse factors that augment the continuation and uptake of family planning methods. Clients’ satisfaction is one of the core determinants facilitating continuation of family planning methods. There is a major debate yet scanty evidence to contrast public and private sectors with respect to client satisfaction. The objective of this study is to compare quality-of-care provided by public and private sectors of Pakistan through a client satisfaction lens. Methods: We used Pakistan Demographic Heath Survey 2012-13 dataset on 3133 women. Ten different multivariate models were made. to explore the relationship between client satisfaction and dependent outcome after adjusting for all known confounding factors and results are presented as OR and AOR (95% CI). Results: Multivariate analyses showed that clients were less satisfied in contraceptive provision from private sector as compared to public sector (AOR 0.92, 95% CI 0.63-1.68) even though the result was not statistically significant. Clients were more satisfied from private sector as compared to the public sector with respect to other determinants of quality-of-care follow-up care (AOR 3.29, 95% CI 1.95-5.55), infection prevention (AOR 2.41, 95% CI 1.60-3.62), counseling services (AOR 2.01, 95% CI 1.27-3.18, timely treatment (AOR 3.37, 95% CI 2.20-5.15), attitude of staff (AOR 2.23, 95% CI 1.50-3.33), punctuality of staff (AOR 2.28, 95% CI 1.92-4.13), timely referring (AOR 2.34, 95% CI 1.63-3.35), staff cooperation (AOR 1.75, 95% CI 1.22-2.51) and complications handling (AOR 2.27, 95% CI 1.56-3.29). Discussion: Public sector has successfully attained substantial satisfaction levels with respect to provision of contraceptives, but it contrasts previous literature from a multi country studies. Our study though in is concordance with a study from Tanzania where public sector was more likely to offer family planning services to clients as compared to private facilities. Conclusion: In majority of the developing countries, public sector is more involved in FP service provision; however, in Pakistan clients’ satisfaction in private sector is more, which opens doors for public-private partnerships and collaboration in the near future.
Abstract: A chromium-loaded ash originating from incineration of tannery sludge under anoxic conditions was mixed with low grade soda-lime glass powder coming from commercial glass bottles. The relative weight proportions of ash over glass powder tested were 30/70, 40/60 and 50/50. The solid mixtures, formed in green state compacts, were sintered at the temperature range of 800o C up to 1200o C. The resulting products were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray spectrometry (EDXS) and micro-indentation. The above methods were employed to characterize the various phases, microstructure and hardness of the produced materials. Thermal treatment at 800o C and 1000o C produced opaque ceramic products composed of a variety of chromium-containing and chromium-free crystalline phases. Thermal treatment at 1200o C gave rise to composite products, where only chromium-containing crystalline phases were detected. Hardness results suggest that specific products are serious candidates for structural applications.
Abstract: The safety and health performances aspects of a building are the most challenging aspect of facility management. It requires a deep understanding by the building managers on the factors that contribute to health and safety performances. This study attempted to develop an explanatory architectural safety performance model for stratified low-cost housing in Malaysia. The proposed Building Safety and Health Performance (BSHP) model was tested empirically through a survey on 308 construction practitioners using partial least squares (PLS) and structural equation modelling (SEM) tool. Statistical analysis results supports the conclusion that architecture, building services, external environment, management approaches and maintenance management have positive influence on safety and health performance of stratified low-cost housing in Malaysia. The findings provide valuable insights for construction industry to introduce BSHP model in the future where the model could be used as a guideline for training purposes of managers and better planning and implementation of building management.
Abstract: This paper is focused on the CFD simulation of the radiaxial pump (i.e. mixed flow pump) with the aim to detect the reasons of Y-Q characteristic instability. The main reasons of pressure pulsations were detected by means of the analysis of velocity and pressure fields within the pump combined with the theoretical approach. Consequently, the modifications of spiral case and pump suction area were made based on the knowledge of flow conditions and the shape of dissipation function. The primary design of pump geometry was created as the base model serving for the comparison of individual modification influences. The basic experimental data are available for this geometry. This approach replaced the more complicated and with respect to convergence of all computational tasks more difficult calculation for the compressible liquid flow. The modification of primary pump consisted in inserting the three fins types. Subsequently, the evaluation of pressure pulsations, specific energy curves and visualization of velocity fields were chosen as the criterion for successful design.
Abstract: The use of energy dissipation systems for seismic applications has increased worldwide, thus it is necessary to develop practical and modern criteria for their optimal design. Here, a direct displacement-based seismic design approach for frame buildings with hysteretic energy dissipation systems (HEDS) is applied. The building is constituted by two individual structural systems consisting of: 1) a main elastic structural frame designed for service loads; and 2) a secondary system, corresponding to the HEDS, that controls the effects of lateral loads. The procedure implies to control two design parameters: a) the stiffness ratio (α=Kframe/Ktotal system), and b) the strength ratio (γ=Vdamper/Vtotal system). The proposed damage-controlled approach contributes to the design of a more sustainable and resilient building because the structural damage is concentrated on the HEDS. The reduction of the design displacement spectrum is done by means of a damping factor (recently published) for elastic structural systems with HEDS, located in Mexico City. Two limit states are verified: serviceability and near collapse. Instead of the traditional trial-error approach, a procedure that allows the designer to establish the preliminary sizes of the structural elements of both systems is proposed. The design methodology is applied to an 8-story steel building with buckling restrained braces, located in soft soil of Mexico City. With the aim of choosing the optimal design parameters, a parametric study is developed considering different values of હ and . The simplified methodology is for preliminary sizing, design, and evaluation of the effectiveness of HEDS, and it constitutes a modern and practical tool that enables the structural designer to select the best design parameters.
Abstract: A large amount of blast furnace slag is generated in
China. Most ground granulated blast furnace slag (GGBS) however
ends up in low-grade applications. Blast furnace slag, ground to an
appropriate fineness, can be used as a partial replacement of
cementitious material in concrete. The potential for using GGBS in
structural concrete, e.g. concrete beams and columns is investigated
at Xi’an Jiaotong-Liverpool University (XJTLU). With 50% of CEM
I cement replaced with GGBS, peak hydration temperatures
determined in a suspended concrete slab reduced by 20%. This
beneficiary effect has not been further improved with 70% of CEM I
replaced with GGBS. Partial replacement of CEM I with GGBS has a
retardation effect on the early-age strength of concrete. More GGBS
concrete mixes will be conducted to identify an ‘optimum’
replacement level which will lead to a reduced thermal loading,
without significantly compromising the early-age strength of
concrete.
Abstract: Investigations on the accumulation of heavy metals in
water and sediments of river Ogbese were carried out between
December 2010 and February 2011 using Atomic Absorption
Spectrophotometer. Etheria elliptica a sessile organism was also used
to determine the concentration of heavy metal in the aquatic
environmental. In water, Cu had the highest concentration (0.55 –
0.13 mg/l ±0.1) while in sediments, the highest value obtained was in
Fe (1.46-3.89mg/l±0.27). The minimum concentrations recorded
were in Pb; which was below detectable level. The result also
revealed that the shell accumulate more heavy metals than the flesh
of the mussel with Cu in the shell exhibiting a negative correlation
with all the metals in the flesh. However, the condition factor (K)
value is 6.44, an indication of good health. The length-weight
relationship is expressed as W = -0.48 x L 1.94 (r2 = 0.29) showing the
growth pattern to be negatively allometric.