Abstract: This paper presents a new method to detect high impedance faults in radial distribution systems. Magnitudes of third and fifth harmonic components of voltages and currents are used as a feature vector for fault discrimination. The proposed methodology uses a learning vector quantization (LVQ) neural network as a classifier for identifying high impedance arc-type faults. The network learns from the data obtained from simulation of a simple radial system under different fault and system conditions. Compared to a feed-forward neural network, a properly tuned LVQ network gives quicker response.
Abstract: An effort to develop a unit commitment approach
capable of handling large power systems consisting of both thermal
and hydro generating units offers a large profitable return. In order to
be feasible, the method to be developed must be flexible, efficient
and reliable. In this paper, various proposed methods have been
described along with their strengths and weaknesses. As all of these
methods have some sort of weaknesses, a comprehensive algorithm
that combines the strengths of different methods and overcomes each
other-s weaknesses would be a suitable approach for solving
industry-grade unit commitment problem.
Abstract: Axial Flux Permanent Magnet (AFPM) Machines require effective cooling due to their high power density. The detrimental effects of overheating such as degradation of the insulation materials, magnets demagnetization, and increase of Joule losses are well known. This paper describes the CFD simulations performed on a test rig model of an air cooled Axial Flux Permanent Magnet (AFPM) generator built at Durham University to identify the temperatures and heat transfer coefficient on the stator. The Reynolds Averaged Navier-Stokes and the Energy equations are solved and the flow pattern and heat transfer developing inside the machine are described. The Nusselt number on the stator surfaces has been found. The dependency of the heat transfer on the flow field is described temperature field obtained. Tests on an experimental are undergoing in order to validate the CFD results.
Abstract: The supported Pd catalysts were analyzed by X-ray
diffraction and X-ray absorption spectroscopy in order to determine
their global and local structure. The average particle size of the
supported Pd catalysts was determined by X-ray diffraction method.
One of the main purposes of the present contribution is to focus on
understanding the specific role of the Pd particle size determined by
X-ray diffraction and that of the support oxide. Based on X-ray
absorption fine structure spectroscopy analysis we consider that the
whole local structure of the investigated samples are distorted
concerning the atomic number but the distances between atoms are
almost the same as for standard Pd sample. Due to the strong
modifications of the Pd cluster local structure, the metal-support
interface may influence the electronic properties of metal clusters
and thus their reactivity for absorption of the reactant molecules.
Abstract: In today-s modern world, the number of vehicles is
increasing on the road. This causes more people to choose walking
instead of traveling using vehicles. Thus, proper planning of
pedestrians- paths is important to ensure the safety of pedestrians in a
walking area. Crowd dynamics study the pedestrians- behavior and
modeling pedestrians- movement to ensure safety in their walking paths.
To date, many models have been designed to ease pedestrians-
movement. The Social Force Model is widely used among researchers
as it is simpler and provides better simulation results. We will discuss
the problem regarding the ritual of circumambulating the Ka-aba
(Tawaf) where the entrances to this area are usually congested which
worsens during the Hajj season. We will use the computer simulation
model SimWalk which is based on the Social Force Model to simulate
the movement of pilgrims in the Tawaf area. We will first discuss the
effect of uni and bi-directional flows at the gates. We will then restrict
certain gates to the area as the entrances only and others as exits only.
From the simulations, we will study the effect of the distance of other
entrances from the beginning line and their effects on the duration of
pilgrims circumambulate Ka-aba. We will distribute the pilgrims at the
different entrances evenly so that the congestion at the entrances can be
reduced. We would also discuss the various locations and designs of
barriers at the exits and its effect on the time taken for the pilgrims to
exit the Tawaf area.
Abstract: Partial coherence between two signals removing the contribution of a periodic, deterministic signal is proposed for evaluating the interrelationship in multivariate systems. The estimator expression was derived and shown to be independent of such periodic signal. Simulations were used for obtaining its critical value, which were found to be the same as those for Gaussian signals, as well as for evaluating the technique. An Illustration with eletroencephalografic (EEG) signals during photic stimulation is also provided. The application of the proposed technique in both simulation and real EEG data indicate that it seems to be very specific in removing the contribution of periodic sources. The estimate independence of the periodic signal may widen partial coherence application to signal analysis, since it could be used together with simple coherence to test for contamination in signals by a common, periodic noise source.
Abstract: This paper describes the design and modeling
procedure of a novel 5-phase segment type switched reluctance motor
(ST-SRM) under simultaneous two-phase (bipolar) excitation of
windings. The rotor cores of ST-SRM are embedded in an aluminum
block as well as to improve the performance characteristics. The
magnetic circuit of the produced ST-SRM is constructed so that the
magnetic flux paths are short and exclusive to each phase, thereby
minimizing the commutation switching and eddy current losses in the
laminations. The design and simulation principles presented apply
primarily to conventional SRM and ST-SRM. It is proved that the
novel 5-phase switched reluctance motor under two-phase excitation
is superior among the criteria used in comparison. The purposed
model is particularly well suited for high torque and weight
constrained applications such as automobiles, aerospace and military
applications.
Abstract: We present a theory for optimal filtering of infinite sets of random signals. There are several new distinctive features of the proposed approach. First, we provide a single optimal filter for processing any signal from a given infinite signal set. Second, the filter is presented in the special form of a sum with p terms where each term is represented as a combination of three operations. Each operation is a special stage of the filtering aimed at facilitating the associated numerical work. Third, an iterative scheme is implemented into the filter structure to provide an improvement in the filter performance at each step of the scheme. The final step of the concerns signal compression and decompression. This step is based on the solution of a new rank-constrained matrix approximation problem. The solution to the matrix problem is described in this paper. A rigorous error analysis is given for the new filter.
Abstract: As the use of registration packages spreads, the number of the aligned image pairs in image databases (either by manual or automatic methods) increases dramatically. These image pairs can serve as a set of training data. Correspondingly, the images that are to be registered serve as testing data. In this paper, a novel medical image registration method is proposed which is based on the a priori knowledge of the expected joint intensity distribution estimated from pre-aligned training images. The goal of the registration is to find the optimal transformation such that the distance between the observed joint intensity distribution obtained from the testing image pair and the expected joint intensity distribution obtained from the corresponding training image pair is minimized. The distance is measured using the divergence measure based on Tsallis entropy. Experimental results show that, compared with the widely-used Shannon mutual information as well as Tsallis mutual information, the proposed method is computationally more efficient without sacrificing registration accuracy.
Abstract: Exponentially weighted moving average control chart (EWMA) is a popular chart used for detecting shift in the mean of parameter of distributions in quality control. The objective of this paper is to compare the efficiency of control chart to detect an increases in the mean of a process. In particular, we compared the Maximum Exponentially Weighted Moving Average (MaxEWMA) and Maximum Generally Weighted Moving Average (MaxGWMA) control charts when the observations are Exponential distribution. The criteria for evaluate the performance of control chart is called, the Average Run Length (ARL). The result of comparison show that in the case of process is small sample size, the MaxEWMA control chart is more efficiency to detect shift in the process mean than MaxGWMA control chart. For the case of large sample size, the MaxEWMA control chart is more sensitive to detect small shift in the process mean than MaxGWMA control chart, and when the process is a large shift in mean, the MaxGWMA control chart is more sensitive to detect mean shift than MaxEWMA control chart.
Abstract: In order to provide accurate heart rate variability
indices of sympathetic and parasympathetic activity, the low
frequency and high frequency components of an RR heart rate signal
must be adequately separated. This is not always possible by just
applying spectral analysis, as power from the high and low frequency
components often leak into their adjacent bands. Furthermore,
without the respiratory spectra it is not obvious that the low
frequency component is not another respiratory component, which
can appear in the lower band. This paper describes an adaptive filter,
which aids the separation of the low frequency sympathetic and high
frequency parasympathetic components from an ECG R-R interval
signal, enabling the attainment of more accurate heart rate variability
measures. The algorithm is applied to simulated signals and heart rate
and respiratory signals acquired from an ambulatory monitor
incorporating single lead ECG and inductive plethysmography
sensors embedded in a garment. The results show an improvement
over standard heart rate variability spectral measurements.
Abstract: This paper describes a 2.4 GHz passive switch mixer
and a 5/2.5 GHz voltage-controlled negative Gm oscillator (VCO)
with an inversion-mode MOS varactor. Both circuits are implemented
using a 1P8M 0.13 μm process. The switch mixer has an input
referred 1 dB compression point of -3.89 dBm and a conversion
gain of -0.96 dB when the local oscillator power is +2.5 dBm.
The VCO consumes only 1.75 mW, while drawing 1.45 mA from a
1.2 V supply voltage. In order to reduce the passives size, the VCO
natural oscillation frequency is 5 GHz. A clocked CMOS divideby-
two circuit is used for frequency division and quadrature phase
generation. The VCO has a -109 dBc/Hz phase noise at 1 MHz
frequency offset and a 2.35-2.5 GHz tuning range (after the frequency
division), thus complying with ZigBee requirements.
Abstract: Interactive web-based computer simulations are
needed by the medical community to replicate the experience of
surgical procedures as closely and realistically as possible without
the need to practice on corpses, animals and/or plastic models. In this
paper, we offer a review on current state of the research on
simulations of surgical threads, identify future needs and present our
proposed plans to meet them. Our goal is to create a physics-based
simulator, which will predict the behavior of surgical thread when
subjected to conditions commonly encountered during surgery. To
that end, we will i) develop three dimensional finite element models
based on the Cosserat theory of elasticity ii) test and feedback results
with the medical community and iii) develop a web-based user
interface to run/command our simulator and visualize the results. The
impacts of our research are that i) it will contribute to the
development of a new generation of training for medical school
students and ii) the simulator will be useful to expert surgeons in
developing new, better and less risky procedures.
Abstract: Different techniques for estimating seasonal water
use from soil profile water depletion frequently do not account for
flux below the root zone. Shallow water table contribution to supply
crop water use may be important in arid and semi-arid regions.
Development of predictive root uptake models, under influence of
shallow water table makes it possible for planners to incorporate
interaction between water table and root zone into design of irrigation
projects. A model for obtaining soil moisture depletion from root
zone and water movement below it is discussed with the objective to
determine impact of shallow water table on seasonal moisture
depletion patterns under water table depth variation, up to the bottom
of root zone. The role of different boundary conditions has also been
considered. Three crops: Wheat (Triticum aestivum), Corn (Zea
mays) and Potato (Solanum tuberosum), common in arid & semi-arid
regions, are chosen for the study. Using experimentally obtained soil
moisture depletion values for potential soil moisture conditions,
moisture depletion patterns using a non linear root uptake model have
been obtained for different water table depths. Comparative analysis
of the moisture depletion patterns under these conditions show a wide
difference in percent depletion from different layers of root zone
particularly top and bottom layers with middle layers showing
insignificant variation in moisture depletion values. Moisture
depletion in top layer, when the water table rises to root zone
increases by 19.7%, 22.9% & 28.2%, whereas decrease in bottom
layer is 68.8%, 61.6% & 64.9% in case of wheat, corn & potato
respectively. The paper also discusses the causes and consequences
of increase in moisture depletion from top layers and exceptionally
high reduction in bottom layer, and the possible remedies for the
same. The numerical model developed for the study can be used to
help formulating irrigation strategies for areas where shallow
groundwater of questionable quality is an option for crop production.
Abstract: From the perspective of industrial structure
coordination and based on an explicit definition for the connotation of
industrial structure coordination, the synergetic coefficients are used
to measure the coordination degree between three industries' input
structure and output structure, and then the efficacy function method is
employed to comprehensively evaluate the level of China-s industrial
structure optimization. It is showed that Chinese industrial structure
presented a "v-shaped" variation tendency between 1996 and 2008,
and its industrial structure adjustment got obvious achievements after
2003, with the industrial structure optimization level increasing
continuously. However in 2009, the level of China-s industrial
structure optimization declined sharply due to the decreasing
contribution degree of value added structure and energy structure
coordination and the lower coordination degree of value added
structure and capital structure.
Abstract: As a result of the ever-changing environment and the demands of rganisations- customers, it is important to recognise the importance of some important managerial challenges. It is the sincere belief that failure to meet these challenges, will ultimately contribute to inevitable problems for organisations. This recognition
requires from managers and by implication organisations to be engaged in ethical behaviour, identity awareness and learning organisational behaviour. All these aspects actually reflect on the
importance of intellectual capital as the competitive weapons for
organisations in the future.
Abstract: Currently in many major cities, public transit schedules
are disseminated through lists of routes, grids of stop times and
static maps. This paper describes a web based geographic information
system which disseminates the same schedule information through
intuitive GIS techniques. Using data from Calgary, Canada, an map
based interface has been created to allow users to see routes, stops and
moving buses all at once. Zoom and pan controls as well as satellite
imagery allows users to apply their personal knowledge about the
local geography to achieve faster, and more pertinent transit results.
Using asynchronous requests to web services, users are immersed
in an application where buses and stops can be added and removed
interactively, without the need to wait for responses to HTTP requests.
Abstract: Most agricultural crops cultivated in Brazil are highly
nutrient demanding. Brazilian soils are generally acidic with low base
saturation and available nutrients. Demand for fertilizer application
has increased because the national agricultural sector expansion. To
improve productivity without environmental impact, there is the need
for the utilization of novel procedures and techniques to optimize
fertilizer application. This includes the digital soil mapping and GIS
application applied to mapping in different scales. This paper is
based on research, realized during 2005 to 2010 by Brazilian
Corporation for Agricultural Research (EMBRAPA) and its partners.
The purpose was to map soil fertility in national and regional scales.
A soil profile data set in national scale (1:5,000,000) was constructed
from the soil archives of Embrapa Soils, Rio de Janeiro and in the
regional scale (1:250,000) from COMIGO Cooperative soil data set,
Rio Verde, Brazil. The mapping was doing using ArcGIS 9.1 tools
from ESRI.
Abstract: We constructed a method of noise reduction for
JPEG-compressed image based on Bayesian inference using the
maximizer of the posterior marginal (MPM) estimate. In this method,
we tried the MPM estimate using two kinds of likelihood, both of
which enhance grayscale images converted into the JPEG-compressed
image through the lossy JPEG image compression. One is the
deterministic model of the likelihood and the other is the probabilistic
one expressed by the Gaussian distribution. Then, using the Monte
Carlo simulation for grayscale images, such as the 256-grayscale
standard image “Lena" with 256 × 256 pixels, we examined the
performance of the MPM estimate based on the performance measure
using the mean square error. We clarified that the MPM estimate via
the Gaussian probabilistic model of the likelihood is effective for
reducing noises, such as the blocking artifacts and the mosquito noise,
if we set parameters appropriately. On the other hand, we found that
the MPM estimate via the deterministic model of the likelihood is not
effective for noise reduction due to the low acceptance ratio of the
Metropolis algorithm.
Abstract: Like any sentient organism, a smart environment
relies first and foremost on sensory data captured from the real
world. The sensory data come from sensor nodes of different
modalities deployed on different locations forming a Wireless Sensor
Network (WSN). Embedding smart sensors in humans has been a
research challenge due to the limitations imposed by these sensors
from computational capabilities to limited power. In this paper, we
first propose a practical WSN application that will enable blind
people to see what their neighboring partners can see. The challenge
is that the actual mapping between the input images to brain pattern
is too complex and not well understood. We also study the
connectivity problem in 3D/2D wireless sensor networks and propose
distributed efficient algorithms to accomplish the required
connectivity of the system. We provide a new connectivity algorithm
CDCA to connect disconnected parts of a network using cooperative
diversity. Through simulations, we analyze the connectivity gains
and energy savings provided by this novel form of cooperative
diversity in WSNs.