Abstract: In this paper, the feasibility study of using a hybrid
system of ground heat exchangers (GHE) and direct evaporative
cooling system in arid weather condition has been performed. The
model is applied for Yazd and Kerman, two cities with arid weather
condition in Iran. The system composed of three sections: Ground-
Coupled-Circuit (GCC), Direct Evaporative Cooler (DEC) and
Cooling Coil Unite (CCU). The GCC provides the necessary precooling
for DEC. The GCC includes four vertical GHE which are
designed in series configuration. Simulation results show that
hybridization of GCC and DEC could provide comfort condition
whereas DEC alone did not. Based on the results the cooling
effectiveness of a hybrid system is more than unity. Thus, this novel
hybrid system could decrease the air temperature below the ambient
wet-bulb temperature. This environmentally clean and energy
efficient system can be considered as an alternative to the mechanical
vapor compression systems.
Abstract: This work focuses on the remediation of polycyclic
aromatic hydrocarbons (PAHs)-contaminated soil via Fenton
treatment coupled with novel chelating agent (CA). The feasibility of
chelated modified Fenton (MF) treatment to promote PAH oxidation
in artificially contaminated soils was investigated in laboratory scale
batch experiments at natural pH. The effects of adding inorganic and
organic CA are discussed. Experiments using different iron catalyst
to CA ratios were conducted, resulting in hydrogen peroxide: soil:
iron: CA weight ratios that varied from 0.049: 1: 0.072: 0.008 to
0.049: 1: 0.072: 0.067. The results revealed that (1) inorganic CA
could provide much higher PAH removal efficiency and (2) most of
the proposed CAs were more efficient than commonly utilised CAs
even at mild ratio. This work highlights the potential of novel
chelating agents in maintaining a suitable environment throughout
the Fenton treatment, particularly in soils with high buffer capacity.
Abstract: LabVIEW and SIMULINK are two most widely used
graphical programming environments for designing digital signal
processing and control systems. Unlike conventional text-based
programming languages such as C, Cµ and MATLAB, graphical
programming involves block-based code developments, allowing a
more efficient mechanism to build and analyze control systems. In
this paper a LabVIEW environment has been employed as a
graphical user interface for monitoring the operation of a controlled
distillation column, by visualizing both the closed loop performance
and the user selected control conditions, while the column dynamics
has been modeled under the SIMULINK environment. This tool has
been applied to the PID based decoupled control of a binary
distillation column. By means of such integrated environments the
control designer is able to monitor and control the plant behavior and
optimize the response when both, the quality improvement of
distillation products and the operation efficiency tasks, are
considered.
Abstract: A network of coupled stochastic oscillators is
proposed for modeling of a cluster of entangled qubits that is
exploited as a computation resource in one-way quantum
computation schemes. A qubit model has been designed as a
stochastic oscillator formed by a pair of coupled limit cycle
oscillators with chaotically modulated limit cycle radii and
frequencies. The qubit simulates the behavior of electric field of
polarized light beam and adequately imitates the states of two-level
quantum system. A cluster of entangled qubits can be associated
with a beam of polarized light, light polarization degree being
directly related to cluster entanglement degree. Oscillatory network,
imitating qubit cluster, is designed, and system of equations for
network dynamics has been written. The constructions of one-qubit
gates are suggested. Changing of cluster entanglement degree caused
by measurements can be exactly calculated.
Abstract: Radiolabeled cyclic RGD peptides targeting integrin αvβ3 are reported as promising agents for the early diagnosis of metastatic tumors. With an aim to improve tumor uptake and retention of the peptide, cyclic RGD peptide dimer E[c (RGDfK)] 2 (E = Glutamic acid, f = phenyl alanine, K = lysine) coupled to the bifunctional chelator DOTA was custom synthesized and radiolabelled with 68Ga. Radiolabelling of cyclic RGD peptide dimer with 68Ga was carried out using HEPES buffer and biological evaluation of the complex was done in nude mice bearing HT29 tumors.
Abstract: The world wide web coupled with the ever-increasing
sophistication of online technologies and software applications puts
greater emphasis on the need of even more sophisticated and
consistent quality requirements modeling than traditional software
applications. Web sites and Web applications (WebApps) are
becoming more information driven and content-oriented raising the
concern about their information quality (InQ). The consistent and
consolidated modeling of InQ requirements for WebApps at different
stages of the life cycle still poses a challenge. This paper proposes an
approach to specify InQ requirements for WebApps by reusing and
extending the ISO 25012:2008(E) data quality model. We also
discuss learnability aspect of information quality for the WebApps.
The proposed ISO 25012 based InQ framework is a step towards a
standardized approach to evaluate WebApps InQ.
Abstract: The objective of the present paper is a numerical
analysis of the flow forces acting on spool surfaces of a pressure
regulated valve. The transient, compressible and turbulent flow
structures inside the valve are simulated using ANSYS FLUENT
coupled with a special UDF. Here, valve inlet pressure is varied in a
stepwise manner. For every value of inlet pressure, transient analysis
leads to a quasi-static flow through the valve. Spool forces are
calculated based on different pressures at inlet. From this information
of spool forces, pressure characteristic of the passive control circuit
has been derived.
Abstract: The paper deals with determination of electromagnetic
and temperature field distribution of induction heating system used
for pipe brazing. The problem is considered as coupled – time
harmonic electromagnetic and transient thermal field. It has been
solved using finite element method. The detailed maps of
electromagnetic and thermal field distribution have been obtained.
The good understanding of the processes in the considered system
ensures possibilities for control, management and increasing the
efficiency of the welding process.
Abstract: This project relates to a two-wheeled self balancing
robot for transferring loads on different locations along a path. This
robot specifically functions as a dual mode navigation to navigate
efficiently along a desired path. First, as a plurality of distance
sensors mounted at both sides of the body for collecting information
on tilt angle of the body and second, as a plurality of speed sensors
mounted at the bottom of the body for collecting information of the
velocity of the body in relative to the ground. A microcontroller for
processing information collected from the sensors and configured to
set the path and to balance the body automatically while a processor
operatively coupled to the microcontroller and configured to compute
change of the tilt and velocity of the body. A direct current motor
operatively coupled to the microcontroller for controlling the wheels
and characterized in that a remote control is operatively coupled to
the microcontroller to operate the robot in dual navigation modes.
Abstract: We have considered an unmagnetized dusty plasma system consisting of ions obeying superthermal distribution and strongly coupled negatively charged dust. We have used reductive perturbation method and derived the Kordeweg-de Vries-Burgers (KdV-Burgers) equation. The behavior of the shock waves in the plasma has been investigated.
Abstract: Age at first marriage is a basic temporal term that is
culturally constructed for marriage relationship between an adult
male and an adult female intended to have sex, to reproduce and to
adapt to environment from one generation to another around the
world. Cross-cultural evidences suggest that age at first marriage for
both male and female not only varies across the cultures, but also
varies among the subcultures of the same society. The purpose of the
study was to compare age at first marriage for husband and wife
including age differences between them between Muslim and Santal
communities in rural Bangladesh. For this we hypothesized that (1)
there were significant differences in age at first marriage and age
interval between husband and wife between Muslim and Santal
communities in rural Bangladesh. In so doing, 288 couples (145 pairs
of couples for Muslim and 143 pairs of couples for Santal) were
selected by cluster random sampling from the Kalna village situated
in the Tanore Upazila of Rajshahi district, Bangladesh, whose
current mean age range was 36.59 years for husband and 28.85 years
for wife for the Muslim and 31.74 years for husband and 25.21 years
for wife for the Santal respectively. The results of Independent
Sample t test showed that mean age at first marriage for the Muslim
samples was 23.05 years for husbands and 15.11 years for wives,
while mean age at first marriage for the Santal samples was 20.71
years for husbands and 14.34 years for wives respectively that were
significantly different at p0.05) among the selected husbands
and wives between the two communities. This study recommends
that further cross-cultural researches should be done on the causeeffect
relationships between socio-cultural factors and age at
marriage between the two communities in Bangladesh.
Abstract: This paper presents the modeling of a MEMS based accelerometer in order to detect the presence of a wheel flat in the railway vehicle. A haversine wheel flat is assigned to one wheel of a 5 DOF pitch plane vehicle model, which is coupled to a 3 layer track model. Based on the simulated acceleration response obtained from the vehicle-track model, an accelerometer is designed that meets all the requirements to detect the presence of a wheel flat. The proposed accelerometer can survive in a dynamic shocking environment with acceleration up to ±150g. The parameters of the accelerometer are calculated in order to achieve the required specifications using lumped element approximation and the results are used for initial design layout. A finite element analysis code (COMSOL) is used to perform simulations of the accelerometer under various operating conditions and to determine the optimum configuration. The simulated results are found within about 2% of the calculated values, which indicates the validity of lumped element approach. The stability of the accelerometer is also determined in the desired range of operation including the condition under shock.
Abstract: Functional imaging procedures for the non-invasive assessment of tissue microcirculation are highly requested, but require a mathematical approach describing the trans- and intercapillary passage of tracer particles. Up to now, two theoretical, for the moment different concepts have been established for tracer kinetic modeling of contrast agent transport in tissues: pharmacokinetic compartment models, which are usually written as coupled differential equations, and the indicator dilution theory, which can be generalized in accordance with the theory of lineartime- invariant (LTI) systems by using a convolution approach. Based on mathematical considerations, it can be shown that also in the case of an open two-compartment model well-known from functional imaging, the concentration-time course in tissue is given by a convolution, which allows a separation of the arterial input function from a system function being the impulse response function, summarizing the available information on tissue microcirculation. Due to this reason, it is possible to integrate the open two-compartment model into the system-theoretic concept of indicator dilution theory (IDT) and thus results known from IDT remain valid for the compartment approach. According to the long number of applications of compartmental analysis, even for a more general context similar solutions of the so-called forward problem can already be found in the extensively available appropriate literature of the seventies and early eighties. Nevertheless, to this day, within the field of biomedical imaging – not from the mathematical point of view – there seems to be a trench between both approaches, which the author would like to get over by exemplary analysis of the well-known model.
Abstract: In this paper, the two-dimension differential transformation method (DTM) is employed to obtain the closed form solutions of the three famous coupled partial differential equation with physical interest namely, the coupled Korteweg-de Vries(KdV) equations, the coupled Burgers equations and coupled nonlinear Schrödinger equation. We begin by showing that how the differential transformation method applies to a linear and non-linear part of any PDEs and apply on these coupled PDEs to illustrate the sufficiency of the method for this kind of nonlinear differential equations. The results obtained are in good agreement with the exact solution. These results show that the technique introduced here is accurate and easy to apply.
Abstract: Nonlinear propagation of ion-acoustic waves in a selfgravitating
dusty plasma consisting of warm positive ions,
isothermal two-temperature electrons and negatively charged dust
particles having charge fluctuations is studied using the reductive
perturbation method. It is shown that the nonlinear propagation of
ion-acoustic waves in such plasma can be described by an uncoupled
third order partial differential equation which is a modified form of
the usual Korteweg-deVries (KdV) equation. From this nonlinear
equation, a new type of solution for the ion-acoustic wave is
obtained. The effects of two-temperature electrons, gravity and dust
charge fluctuations on the ion-acoustic solitary waves are discussed
with possible applications.
Abstract: In this paper the Differential Quadrature Method (DQM) is employed to study the coupled lateral-torsional free vibration behavior of the laminated composite beams. In such structures due to the fiber orientations in various layers, the lateral displacement leads to a twisting moment. The coupling of lateral and torsional vibrations is modeled by the bending-twisting material coupling rigidity. In the present study, in addition to the material coupling, the effects of shear deformation and rotary inertia are taken into account in the definition of the potential and kinetic energies of the beam. The governing differential equations of motion which form a system of three coupled PDEs are solved numerically using DQ procedure under different boundary conditions consist of the combinations of simply, clamped, free and other end conditions. The resulting natural frequencies and mode shapes for cantilever beam are compared with similar results in the literature and good agreement is achieved.
Abstract: This paper presents the approach to design the Auto-
Tuning PID controller for interactive Water Level Process using
integral step response. The Integral Step Response (ISR) is the
method to model a dynamic process which can be done easily,
conveniently and very efficiently. Therefore this method is advantage
for design the auto tune PID controller. Our scheme uses the root
locus technique to design PID controller. In this paper MATLAB is
used for modeling and testing of the control system. The
experimental results of the interacting water level process can be
satisfyingly illustrated the transient response and the steady state
response.
Abstract: A new method identifies coupled fluid-structure system with a reduced set of state variables is presented. Assuming that the structural model is known a priori either from an analysis or a test and using linear transformations between structural and aeroelastic states, it is possible to deduce aerodynamic information from sampled time histories of the aeroelastic system. More specifically given a finite set of structural modes the method extracts generalized aerodynamic force matrix corresponding to these mode shapes. Once the aerodynamic forces are known, an aeroelastic reduced-order model can be constructed in discrete-time, state-space format by coupling the structural model and the aerodynamic system. The resulting reduced-order model is suitable for constant Mach, varying density analysis.
Abstract: Predictions of flow and heat transfer characteristics and shape optimization in internally finned circular tubes have been performed on three-dimensional periodically fully developed turbulent flow and thermal fields. For a trapezoidal fin profile, the effects of fin height h, upper fin widths d1, lower fin widths d2, and helix angle of fin ? on transport phenomena are investigated for the condition of fin number of N = 30. The CFD and mathematical optimization technique are coupled in order to optimize the shape of internally finned tube. The optimal solutions of the design variables (i.e., upper and lower fin widths, fin height and helix angle) are numerically obtained by minimizing the pressure loss and maximizing the heat transfer rate, simultaneously, for the limiting conditions of d1 = 0.5~1.5 mm, d2 = 0.5~1.5 mm, h= 0.5~1.5mm, ? = 10~30 degrees. The fully developed flow and thermal fields are predicted using the finite volume method and the optimization is carried out by means of the multi-objective genetic algorithm that is widely used in the constrained nonlinear optimization problem.
Abstract: This paper presents a numerical approach for the static
and dynamic analysis of hydrodynamic radial journal bearings. In the
first part, the effect of shaft and housing deformability on pressure
distribution within oil film is investigated. An iterative algorithm that
couples Reynolds equation with a plane finite elements (FE)
structural model is solved. Viscosity-to-pressure dependency (Vogel-
Barus equation) is also included. The deformed lubrication gap and
the overall stress state are obtained. Numerical results are presented
with reference to a typical journal bearing configuration at two
different inlet oil temperatures. Obtained results show the great
influence of bearing components structural deformation on oil
pressure distribution, compared with results for ideally rigid
components. In the second part, a numerical approach based on
perturbation method is used to compute stiffness and damping
matrices, which characterize the journal bearing dynamic behavior.