Abstract: A Comparison and evaluation of the different
condition monitoring (CM) techniques was applied experimentally
on RC e.g. Dynamic cylinder pressure and crankshaft Instantaneous
Angular Speed (IAS), for the detection and diagnosis of valve faults
in a two - stage reciprocating compressor for a programme of
condition monitoring which can successfully detect and diagnose a
fault in machine. Leakage in the valve plate was introduced
experimentally into a two-stage reciprocating compressor. The effect
of the faults on compressor performance was monitored and the
differences with the normal, healthy performance noted as a fault
signature been used for the detection and diagnosis of faults.
The paper concludes with what is considered to be a unique
approach to condition monitoring. First, each of the two most useful
techniques is used to produce a Truth Table which details the
circumstances in which each method can be used to detect and
diagnose a fault. The two Truth Tables are then combined into a
single Decision Table to provide a unique and reliable method of
detection and diagnosis of each of the individual faults introduced
into the compressor. This gives accurate diagnosis of compressor
faults.
Abstract: The temporal nature of negative selection is an under exploited area. In a negative selection system, newly generated antibodies go through a maturing phase, and the survivors of the phase then wait to be activated by the incoming antigens after certain number of matches. These without having enough matches will age and die, while these with enough matches (i.e., being activated) will become active detectors. A currently active detector may also age and die if it cannot find any match in a pre-defined (lengthy) period of time. Therefore, what matters in a negative selection system is the dynamics of the involved parties in the current time window, not the whole time duration, which may be up to eternity. This property has the potential to define the uniqueness of negative selection in comparison with the other approaches. On the other hand, a negative selection system is only trained with “normal" data samples. It has to learn and discover unknown “abnormal" data patterns on the fly by itself. Consequently, it is more appreciate to utilize negation selection as a system for pattern discovery and recognition rather than just pattern recognition. In this paper, we study the potential of using negative selection in discovering unknown temporal patterns.
Abstract: In this study, rotating flexible shaft-disk system
having flexible beams is considered as a dynamic system. After
neglecting nonlinear terms, torsional vibration of the shaft-disk
system and lateral and longitudinal vibration of the flexible beam are
still coupled through the motor speed. The system has three natural
frequencies; the flexible shaft-disk system torsional natural
frequency, the flexible beam lateral and longitudinal natural
frequencies. Eigenvalue calculations show that while the shaft speed
changes, torsional natural frequency of the shaft-disk system and the
beam longitudinal natural frequency are not changing but the beam
lateral natural frequency changes. Beam lateral natural frequency
stays the same as the nonrotating beam lateral natural frequency ωb
until the motor speed ωm is equal to ωb. After then ωb increases and
remains equal to the motor speed ωm until the motor speed is equal to
the shaft-disk system natural frequency ωT. Then the beam lateral
natural frequency ωb becomes equal to the natural frequency ωT and
stays same while the motor speed ωm is increased. Modal amplitudes
and phase angles of the vibrations are also plotted against the motor
speed ωm.
Abstract: For stable bipedal gait generation on the level floor,
efficient restoring of mechanical energy lost by heel collision at
the ground is necessary. Parametric excitation principle is one of
the solutions. We dealt with the robot-s total center of mass as
an inverted pendulum to consider the total dynamics of the robot.
Parametrically excited walking requires the use of continuous target
trajectory that is close to discontinuous optimal trajectory. In this
paper, we proposed the new target trajectory based on a position
in the walking direction. We surveyed relations between walking
performance and the parameters that form the target trajectory via
numerical simulations. As a result, it was found that our target
trajectory has the similar characteristics of a parametrically excited
inverted pendulum.
Abstract: This paper presents a experiment to estimate the
influences of cutting conditions in microstructure changes of
machining austenitic 304 stainless steel, especially for wear insert. The
wear insert were prefabricated with a width of 0.5 mm. And the forces,
temperature distribution, RS, and microstructure changes were
measured by force dynamometer, infrared thermal camera, X-ray
diffraction, XRD, SEM, respectively. The results told that the different
combinations of machining condition have a significant influence on
machined surface microstructure changes. In addition to that, the
ANOVA and AOMwere used to tell the different influences of cutting
speed, feed rate, and wear insert.
Abstract: We study dynamic instability in high-rise steel moment
resisting frames (SMRFs) subjected to synthetic long-period ground
motions caused by hypothetical huge subduction earthquakes. Since
long duration as well as long dominant periods is a characteristic of
long-period ground motions, interstory drifts may enter the negative
postyield stiffness range many times when high-rise buildings are
subjected to long-period ground motions. Through the case studies of
9 high-rise SMRFs designed in accordance with the Japanese design
practice in 1980s, we demonstrate that drifting, or accumulation of
interstory drifts in one direction, occurs at the lower stories of the
SMRFs, if their natural periods are close to the dominant periods of the
long-period ground motions. The drifting led to residual interstory
drift ratio over 0.01, or to collapse if the design base shear was small.
Abstract: This work is an attempt to use the standard Smoothed
Particle Hydrodynamics methodology for the simulation of the
complex unsteady, free-surface flow in a rotating Turgo impulse
water turbine. A comparison of two different geometries was
conducted. The SPH method due to its mesh-less nature is capable of
capturing the flow features appearing in the turbine, without
diffusion at the water/air interface. Furthermore results are compared
with a commercial CFD package (Fluent®) and the SPH algorithm
proves to be capable of providing similar results, in much less time
than the mesh based CFD program. A parametric study was also
performed regarding the turbine inlet angle.
Abstract: Due to the complex network architecture, the mobile
adhoc network-s multihop feature gives additional problems to the
users. When the traffic load at each node gets increased, the
additional contention due its traffic pattern might cause the nodes
which are close to destination to starve the nodes more away from the
destination and also the capacity of network is unable to satisfy the
total user-s demand which results in an unfairness problem. In this
paper, we propose to create an algorithm to compute the optimal
MAC-layer bandwidth assigned to each flow in the network. The
bottleneck links contention area determines the fair time share which
is necessary to calculate the maximum allowed transmission rate used
by each flow. To completely utilize the network resources, we
compute two optimal rates namely, the maximum fair share and
minimum fair share. We use the maximum fair share achieved in
order to limit the input rate of those flows which crosses the
bottleneck links contention area when the flows that are not allocated
to the optimal transmission rate and calculate the following highest
fair share. Through simulation results, we show that the proposed
protocol achieves improved fair share and throughput with reduced
delay.
Abstract: This research deals with techno economic analysis to select the most economic desalination method for Asalouyeh combined cycle power plant . Due to lack of fresh water, desalination of sea water is necessary to provide required DM water of Power Plant. The most common desalination methods are RO, MSF, MED, and MED–TVC. In this research, methods of RO, MED, and MED– TVC have been compared. Simulation results show that recovery of heat of exhaust gas of main stack is optimum case for providing DM water required for injected steam of MED desalination. This subject is very important because of improving thermal efficiency of power plant using extra heat recovery. Also, it has been shown that by adding 3 rows of finned tube to de-aerator evaporator, which is very simple and low cost, required steam for generating 5200 m3/day of desalinated water is obtainable.
Abstract: Several studies have shown the association between
ambient particulate matter (PM) and adverse health effects and
climate change, thus highlighting the need to limit the anthropogenic
sources of PM. PM Exposure is commonly monitored as mass
concentration of PM10 (particle aerodynamic diameter < 10μm) or
PM2.5 (particle aerodynamic diameter < 2.5μm), although increasing
toxicity with decreasing aerodynamic diameter has been reported due
to increased surface area and enhanced chemical reactivity with other
species. Additionally, the light scattering properties of PM increases
with decreasing size. Hence, it is important to study the chemical
characterization of finer fraction of the particulate matter and to
identify their sources so that they can be controlled appropriately to a
large extent at the sources before reaching to the receptors.
Abstract: The group mutual exclusion (GME) problem is a
variant of the mutual exclusion problem. In the present paper a
token-based group mutual exclusion algorithm, capable of handling
transient faults, is proposed. The algorithm uses the concept of
dynamic request sets. A time out mechanism is used to detect the
token loss; also, a distributed scheme is used to regenerate the token.
The worst case message complexity of the algorithm is n+1. The
maximum concurrency and forum switch complexity of the
algorithm are n and min (n, m) respectively, where n is the number of
processes and m is the number of groups. The algorithm also satisfies
another desirable property called smooth admission. The scheme can
also be adapted to handle the extended group mutual exclusion
problem.
Abstract: In this paper, we investigate the study of techniques
for scheduling users for resource allocation in the case of multiple
input and multiple output (MIMO) packet transmission systems. In
these systems, transmit antennas are assigned to one user or
dynamically to different users using spatial multiplexing. The
allocation of all transmit antennas to one user cannot take full
advantages of multi-user diversity. Therefore, we developed the case
when resources are allocated dynamically. At each time slot users
have to feed back their channel information on an uplink feedback
channel. Channel information considered available in the schedulers
is the zero forcing (ZF) post detection signal to interference plus
noise ratio. Our analysis study concerns the round robin and the
opportunistic schemes.
In this paper, we present an overview and a complete capacity
analysis of these schemes. The main results in our study are to give
an analytical form of system capacity using the ZF receiver at the
user terminal. Simulations have been carried out to validate all
proposed analytical solutions and to compare the performance of
these schemes.
Abstract: Electromyography (EMG) signal processing has been investigated remarkably regarding various applications such as in rehabilitation systems. Specifically, wavelet transform has served as a powerful technique to scrutinize EMG signals since wavelet transform is consistent with the nature of EMG as a non-stationary signal. In this paper, the efficiency of wavelet transform in surface EMG feature extraction is investigated from four levels of wavelet decomposition and a comparative study between different mother wavelets had been done. To recognize the best function and level of wavelet analysis, two evaluation criteria, scatter plot and RES index are recruited. Hereupon, four wavelet families, namely, Daubechies, Coiflets, Symlets and Biorthogonal are studied in wavelet decomposition stage. Consequently, the results show that only features from first and second level of wavelet decomposition yields good performance and some functions of various wavelet families can lead to an improvement in separability class of different hand movements.
Abstract: Personal name matching system is the core of
essential task in national citizen database, text and web mining,
information retrieval, online library system, e-commerce and record
linkage system. It has necessitated to the all embracing research in
the vicinity of name matching. Traditional name matching methods
are suitable for English and other Latin based language. Asian
languages which have no word boundary such as Myanmar language
still requires sounds alike matching system in Unicode based
application. Hence we proposed matching algorithm to get analogous
sounds alike (phonetic) pattern that is convenient for Myanmar
character spelling. According to the nature of Myanmar character, we
consider for word boundary fragmentation, collation of character.
Thus we use pattern conversion algorithm which fabricates words in
pattern with fragmented and collated. We create the Myanmar sounds
alike phonetic group to help in the phonetic matching. The
experimental results show that fragmentation accuracy in 99.32% and
processing time in 1.72 ms.
Abstract: The dynamics of a delayed mathematical model for
Hes1 oscillatory expression are investigated. The linear stability of
positive equilibrium and existence of local Hopf bifurcation are
studied. Moreover, the global existence of large periodic solutions
has been established due to the global bifurcation theorem.
Abstract: This paper demonstrates an effort of a serviceoriented
engineering department in improving the sharing and
transfer of knowledge. Although the department consist of only six
employees, but it provides services in various chemical application in
an oil and gas business. The services provided span across Asia
Pacific region mainly Indonesia, Myanmar, Vietnam, Brunei,
Thailand and Singapore. Currently there are no effective tools or
integrated systems that support the sharing or transfer and
maintenance of knowledge so the department has considered
preserving this valuable knowledge by developing a Knowledge
Management System (KMS). This paper presents the development of
a KMS to support the sharing of knowledge in a service-oriented
engineering department of an oil and gas company. The embedded
features in the KMS like blog and forum will encourage iterative
process of knowledge sharing among the employees in the
department. The information and knowledge being shared, discussed
and communicated will be then achieved for future re-use. The re-use
of the knowledge allows the department to reduce redundant efforts
in providing consistent, up-to-date and cost effective of the best
solution to the its clients.
Abstract: Many environment specific methods and systems for Robot Navigation exist. However vast strides in the evolution of navigation technologies and system techniques create the need for a general unified framework that is scalable, modular and dynamic. In this paper a Unified Framework for a Robust Conflict-free Robot Navigation System that can be used for either a structured or unstructured and indoor or outdoor environments has been proposed. The fundamental design aspects and implementation issues encountered during the development of the module are discussed. The results of the deployment of three major peripheral modules of the framework namely the GSM based communication module, GIS Module and GPS module are reported in this paper.
Abstract: Coverage is one of the main research interests in wireless sensor networks (WSN), it is used to determine the quality of service (QoS) of the networks. Therefore this paper aims to review the common strategies use in solving coverage problem in WSN. The strategies studied are used during deployment phase where the coverage is calculated based on the placement of the sensors on the region of interest (ROI). The strategies reviewed are categorized into three groups based on the approaches used, namely; force based, grid based or computational geometry based approach.
Abstract: In this paper we will consider the most known ratios
control schemes ((L/D, V/B),(L/D,V/F), Ryskamp-s, and
(D/(L+D),V/B)) for binary distillation column and we compare them
in the basis of interactions and disturbance propagation. The models
for these configurations are deuced using mathematical
transformations taking the energy balance structure (LV) as a base
model. The dynamic relative magnitude criterion (DRMC) is used to
assess the interactions. The results show that the introduction of
ratios in controlling the column tends to minimize the degree of
interactions between the loops.
Abstract: This research details a Computational Fluid Dynamics (CFD) approach to model fluid flow in a journal bearing with 8 equispaced semi-circular axial grooves. Water is used as the lubricant and is fed from one end of the bearing to the other, under pressure. The geometry of the bearing is modeled using a commercially available modeling software GAMBIT and the flow analysis is performed using a dedicated CFD analysis software FLUENT. The pressure distribution in the bearing clearance is obtained from FLUENT for various whirl ratios and is used to calculate the hydrodynamic force components in the radial and tangential direction of the bearing. These values along with the various whirl speeds can be used to do a regression analysis to determine the stiffness and damping coefficients. The values obtained are then compared with the stiffness and damping coefficients of a 3 Axial groove water lubricated journal bearing and those obtained from a FORTRAN code for a similar bearing.