Abstract: Vancron 40, a nitrided powder metallurgical tool
Steel, is used in cold work applications where the predominant failure
mechanisms are adhesive wear or galling. Typical applications of
Vancron 40 are among others fine blanking, cold extrusion, deep
drawing and cold work rolls for cluster mills. Vancron 40 positive
results for cold work rolls for cluster mills and as a tool for some
severe metal forming process makes it competitive compared to other
type of work rolls that require higher precision, among others in cold
rolling of thin stainless steel, which required high surface finish
quality. In this project, three roll materials for cold rolling of stainless
steel strip was examined, Vancron 40, Narva 12B (a high-carbon,
high-chromium tool steel alloyed with tungsten) and Supra 3 (a
Chromium-molybdenum tungsten-vanadium alloyed high speed
steel). The purpose of this project was to study the depth profiles of
the ironed stainless steel strips, emergence of galling and to study the
lubrication performance used by steel industries. Laboratory
experiments were conducted to examine scratch of the strip, galling
and surface roughness of the roll materials under severe tribological
conditions. The critical sliding length for onset of galling was
estimated for stainless steel with four different lubricants. Laboratory
experiments result of performance evaluation of resistance capability
of rolls toward adhesive wear under severe conditions for low and
high reductions. Vancron 40 in combination with cold rolling
lubricant gave good surface quality, prevents galling of
metal surfaces and good bearing capacity.
Abstract: The mechanics of rip currents are complex, involving
interactions between waves, currents, water levels and the bathymetry,
that present particular challenges for numerical models. Here,
the effects of a grid-spacing dependent horizontal mixing on the
wave-current interactions are studied. Near the shore, wave rays
diverge from channels towards bar crests because of refraction by
topography and currents, in a way that depends on the rip current
intensity which is itself modulated by the horizontal mixing. At
low resolution with the grid-spacing dependent horizontal mixing,
the wave motion is the same for both coupling modes because the
wave deviation by the currents is weak. In high resolution case,
however, classical results are found with the stabilizing effect of
the flow by feedback of waves on currents. Lastly, wave-current
interactions and the horizontal mixing strongly affect the intensity
of the three-dimensional rip velocity.
Abstract: Physics Education Research (PER) results have shown
that students do not achieve the expected level of competency in
understanding the concepts of different domains of Physics learning
when taught by the traditional teaching methods, the concepts of
Electricity and Magnetism (E&M) being one among them.
Simulation being one of the valuable instructional tools renders an
opportunity to visualize varied experiences with such concepts.
Considering the electric force concept which requires extensive use
of vector representations, we report here the outcome of the research
results pertaining to the student understanding of this concept and the
role of simulation in using vector representation. The simulation
platform provides a positive impact on the use of vector
representation.
The first stage of this study involves eliciting and analyzing
student responses to questions that probe their understanding of the
concept of electrostatic force and this is followed by four stages of
student interviews as they use the interactive simulations of electric
force in one dimension. Student responses to the questions are
recorded in real time using electronic pad. A validation test interview
is conducted to evaluate students' understanding of the electric force
concept after using interactive simulation. Results indicate lack of
procedural knowledge of the vector representation. The study
emphasizes the need for the choice of appropriate simulation and
mode of induction for learning.
Abstract: The number of Ground Motion Prediction Equations
(GMPEs) used for predicting peak ground acceleration (PGA) and
the number of earthquake recordings that have been used for fitting
these equations has increased in the past decades. The current PF-L
database contains 3550 recordings. Since the GMPEs frequently
model the peak ground acceleration the goal of the present study was
to refit a selection of 44 of the existing equation models for PGA in
light of the latest data. The algorithm Levenberg-Marquardt was used
for fitting the coefficients of the equations and the results are
evaluated both quantitatively by presenting the root mean squared
error (RMSE) and qualitatively by drawing graphs of the five best
fitted equations. The RMSE was found to be as low as 0.08 for the
best equation models. The newly estimated coefficients vary from the
values published in the original works.
Abstract: The spring-driven ball-type check valve is one of the
most important components of hydraulic systems: it controls the
position of the ball and prevents backward flow. To simplify the
structure, the spring must be eliminated, and to accomplish this, the
flow pattern and the behavior of the check ball in L-shaped pipe must
be determined. In this paper, we present a full-scale model of a check
ball made of acrylic resin, and we determine the relationship between
the initial position of the ball, the position and diameter of the inflow
port. The check flow rate increases in a standard center inflow model,
and it is possible to greatly decrease the check-flow rate by shifting the
inflow from the center.
Abstract: Conventional educational practices, do not offer all
the required skills for teachers to successfully survive in today’s
workplace. Due to poor professional training, a big gap exists across
the curriculum plan and the teacher practices in the classroom. As
such, raising the quality of teaching through ICT-enabled training and
professional development of teachers should be an urgent priority.
‘Mobile Learning’, in that vein, is an increasingly growing field of
educational research and practice across schools and work places. In
this paper, we propose a novel Mobile learning system that allows the
users to learn through an intelligent mobile learning in cooperatively
every-time and every-where. The system will reduce the training cost
and increase consistency, efficiency, and data reliability. To establish
that our system will display neither functional nor performance
failure, the evaluation strategy is based on formal observation of
users interacting with system followed by questionnaires and
structured interviews.
Abstract: Bacterial strains capable of degradation of malathion
from the domestic sewage were isolated by an enrichment culture
technique. Three bacterial strains were screened and identified as
Acinetobacter baumannii (AFA), Pseudomonas aeruginosa (PS1),
and Pseudomonas mendocina (PS2) based on morphological,
biochemical identification and 16S rRNA sequence analysis.
Acinetobacter baumannii AFA was the most efficient malathion
degrading bacterium, so used for further biodegradation study. AFA
was able to grow in mineral salt medium (MSM) supplemented with
malathion (100 mg/l) as a sole carbon source, and within 14 days,
84% of the initial dose was degraded by the isolate measured by high
performance liquid chromatography. Strain AFA could also degrade
other organophosphorus compounds including diazinon, chlorpyrifos
and fenitrothion. The effect of different culture conditions on the
degradation of malathion like inoculum density, other carbon or
nitrogen sources, temperature and shaking were examined.
Degradation of malathion and bacterial cell growth were accelerated
when culture media were supplemented with yeast extract, glucose
and citrate. The optimum conditions for malathion degradation by
strain AFA were; an inoculum density of 1.5x 10^12CFU/ml at 30°C
with shaking. A specific polymerase chain reaction primers were
designed manually using multiple sequence alignment of the
corresponding carboxylesterase enzymes of Acinetobacter species.
Sequencing result of amplified PCR product and phylogenetic
analysis showed low degree of homology with the other
carboxylesterase enzymes of Acinetobacter strains, so we suggested
that this enzyme is a novel esterase enzyme. Isolated bacterial strains
may have potential role for use in bioremediation of malathion
contaminated.
Abstract: Solenoid operated electromagnetic control valve
(ECV) playing an important role for car’s air conditioning control
system. ECV is used in external variable displacement swash plate
type compressor and controls the entire air conditioning system by
means of a pulse width modulation (PWM) input signal supplying
from an external source (controller). Complete form of ECV contains
number of internal features like valve body, core, valve guide,
plunger, guide pin, plunger spring, bellows etc. While designing the
ECV; dimensions of different internal items must meet the standard
requirements as it is quite challenging. In this research paper,
especially the dimensioning of ECV body and its three pressure ports
through which the air/refrigerant passes are considered. Here internal
leakage test analysis of ECV body is being carried out from its
discharge port (Pd) to crankcase port (Pc) when the guide valve is
placed inside it. The experiments have made both in ordinary and
digital system using different assumptions and thereafter compare the
results.
Abstract: In medical imaging, segmentation of different areas of
human body like bones, organs, tissues, etc. is an important issue.
Image segmentation allows isolating the object of interest for further
processing that can lead for example to 3D model reconstruction of
whole organs. Difficulty of this procedure varies from trivial for
bones to quite difficult for organs like liver. The liver is being
considered as one of the most difficult human body organ to segment.
It is mainly for its complexity, shape versatility and proximity of
other organs and tissues. Due to this facts usually substantial user
effort has to be applied to obtain satisfactory results of the image
segmentation. Process of image segmentation then deteriorates from
automatic or semi-automatic to fairly manual one. In this paper,
overview of selected available software applications that can handle
semi-automatic image segmentation with further 3D volume
reconstruction of human liver is presented. The applications are being
evaluated based on the segmentation results of several consecutive
DICOM images covering the abdominal area of the human body.
Abstract: The absorption power generation cycle based on the
ammonia-water mixture has attracted much attention for efficient
recovery of low-grade energy sources. In this paper a thermodynamic
performance analysis is carried out for a Kalina cycle using
ammonia-water mixture as a working fluid for efficient conversion of
low-temperature heat source in the form of sensible energy. The
effects of the source temperature on the system performance are
extensively investigated by using the thermodynamic models. The
results show that the source temperature as well as the ammonia mass
fraction affects greatly on the thermodynamic performance of the
cycle.
Abstract: Water flow management is one of the most important
parts of river engineering. Non-uniformity distribution of rainfall and
various flow demand with unreasonable flow management will be
caused destroyed of river ecosystem. Then, it is very serious to
determine ecosystem flow requirement. In this paper, Flow duration
curve indices method which has hydrological based was used to
evaluate environmental flow in Gharasou River, Ardabil, Iran. Using
flow duration curve, Q90 and Q95 for different return periods were
calculated. Their magnitude were determined as 1-day, 3-day, 7-day
and 30 day. According the second method, hydraulic alteration
indices often had low and medium range. In order to maintain river at
an acceptable ecological condition, minimum daily discharge of
index Q95 is 0.7 m3.s-1.
Abstract: Fructo-oligosaccharides (FOS) are produced from
sucrose by Aureobasidium pullulans in yields between 40-60%
(w/w). To increase the amount of FOS it is necessary to remove the
small, non-prebiotic sugars, present. Two methods for producing
high-purity FOS have been developed: the use of microorganisms
able to consume small saccharides; and the use of continuous
chromatography to separate sugars: simulated moving bed (SMB). It
is herein proposed the combination of both methods. The aim of this
study is to optimize the composition of the fermentative broth (in
terms of salts and sugars) that will be further purified by SMB. A
yield of 0.63 gFOS.gSucrose^-1 was obtained with A. pullulans using low
amounts of salts in the initial fermentative broth. By removing the
small sugars, Saccharomyces cerevisiae and Zymomonas mobilis
increased the percentage of FOS from around 56.0% to 83% (w/w) in
average, losing only 10% (w/w) of FOS during the recovery process.
Abstract: Some regularities of formation of a new structural
state of the thermoplastic polymers - gradually oriented (stretched)
state (GOS) are discussed. Transition into GOS is realized by the
graded oriented stretching - by action of inhomogeneous mechanical
field on the isotropic linear polymers or by zone stretching that is
implemented on a standard tensile-testing machine with using a
specially designed zone stretching device (ZSD). Both technical
approaches (especially zone stretching method) allows to manage the
such quantitative parameters of gradually oriented polymers as a
range of change in relative elongation/orientation degree, length of
this change and profile (linear, hyperbolic, parabolic, logarithmic,
etc.). The possibility of obtaining functionally graded materials
(FGMs) by graded orientation method is briefly discussed. Uniaxial
graded stretching method should be considered as an effective
technological solution to create polymer materials with a
predetermined gradient of physical properties.
Abstract: The study is a review of the literature concerning the
consequences of non-standard monetary policy, which are used by
central banks during unconventional periods, threatening banking
sector instability. In particular, the attention was paid to the effects of
non-standard monetary policy tools for financial markets. However,
the empirical evidence about their effects and real consequences for
financial markets is still not final. The main aim of the study is to
survey consequences of standard and non-standard monetary policy
instruments, implemented during the global financial crisis in the
United States, United Kingdom and euro area, with particular
attention to the results for the stabilization of global financial
markets. The study consists mainly of the empirical review,
indicating the impact of the implementation of these tools for
financial markets. The following research methods were used in the
study: literature studies, including domestic and foreign literature,
cause and effect analysis and statistical analysis.
Abstract: In this paper a real-time obstacle avoidance approach
for both autonomous and non-autonomous dynamical systems (DS) is
presented. In this approach the original dynamics of the controller
which allow us to determine safety margin can be modulated.
Different common types of DS increase the robot’s reactiveness in
the face of uncertainty in the localization of the obstacle especially
when robot moves very fast in changeable complex environments.
The method is validated by simulation and influence of different
autonomous and non-autonomous DS such as important
characteristics of limit cycles and unstable DS. Furthermore, the
position of different obstacles in complex environment is explained.
Finally, the verification of avoidance trajectories is described through
different parameters such as safety factor.
Abstract: In this paper, model order reduction method is used
for approximation in linear and nonlinearity aspects in some
experimental data. This method can be used for obtaining offline
reduced model for approximation of experimental data and can
produce and follow the data and order of system and also it can
match to experimental data in some frequency ratios. In this study,
the method is compared in different experimental data and influence
of choosing of order of the model reduction for obtaining the best and
sufficient matching condition for following the data is investigated in
format of imaginary and reality part of the frequency response curve
and finally the effect and important parameter of number of order
reduction in nonlinear experimental data is explained further.
Abstract: Background and aim: It has not been well studied
whether fentanyl-thiopental (FT) is effective and safe for PSA in
orthopedic procedures in Emergency Department (ED). The aim of
this trial was to evaluate the effectiveness of intravenous FT versus
fentanyl-midazolam (FM) in patients who suffered from shoulder
dislocation or distal radial fracture-dislocation.
Methods: In this randomized double-blinded study, Seventy-six
eligible patients were entered the study and randomly received
intravenous FT or FM. The success rate, onset of action and recovery
time, pain score, physicians’ satisfaction and adverse events were
assessed and recorded by treating emergency physicians. The
statistical analysis was intention to treat.
Results: The success rate after administrating loading dose in FT
group was significantly higher than FM group (71.7% vs. 48.9%,
p=0.04); however, the ultimate unsuccessful rate after 3 doses of
drugs in the FT group was higher than the FM group (3 to 1) but it
did not reach to significant level (p=0.61). Despite near equal onset
of action time in two study group (P=0.464), the recovery period in
patients receiving FT was markedly shorter than FM group
(P
Abstract: At certain depths during large diameter displacement
pile driving, rebound well over 0.25 inches was experienced,
followed by a small permanent-set during each hammer blow. High
pile rebound (HPR) soils may stop the pile driving and results in a
limited pile capacity. In some cases, rebound leads to pile damage,
delaying the construction project, and the requiring foundations
redesign. HPR was evaluated at seven Florida sites, during driving of
square precast, prestressed concrete piles driven into saturated, fine
silty to clayey sands and sandy clays. Pile Driving Analyzer (PDA)
deflection versus time data recorded during installation, was used to
develop correlations between cone penetrometer (CPT) pore-water
pressures, pile displacements and rebound. At five sites where piles
experienced excessive HPR with minimal set, the pore pressure
yielded very high positive values of greater than 20 tsf. However, at
the site where the pile rebounded, followed by an acceptable
permanent-set, the measured pore pressure ranged between 5 and 20
tsf. The pore pressure exhibited values of less than 5 tsf at the site
where no rebound was noticed. In summary, direct correlations
between CPTu pore pressure and rebound were produced, allowing
identification of soils that produce HPR.
Abstract: In Brazil, neonatal mortality rate is considered
incompatible with the country development conditions, and has been
a Public Health concern. Reduction in infant mortality rates has also
been part of the Millennium Development Goals, a commitment
made by countries, members of the Organization of United Nations
(OUN), including Brazil. Fetal mortality rate is considered a highly
sensitive indicator of health care quality. Suitable actions, such as
good quality and access to health services may contribute positively
towards reduction in these fetal and neonatal rates. With appropriate
antenatal follow-up and health care during gestation and delivery,
some death causes could be reduced or even prevented by means of
early diagnosis and intervention, as well as changes in risk factors
and interventions. Objectives: To study the quality of maternal and
infant health care based on fetal and neonatal mortality, as well as the
possible actions to prevent those deaths in Botucatu (Brazil).
Methods: Classification of prevention according to the International
Classification of Diseases and the modified Wigglesworth´s
classification. In order to evaluate adequacy, indicators of quality of
antenatal and delivery care were established by the authors. Results:
Considering fetal deaths, 56.7% of them occurred before delivery,
which reveals possible shortcomings in antenatal care, and 38.2% of
them were a result of intra- labor changes, which could be prevented
or reduced by adequate obstetric management. These findings were
different from those in the group of early neonatal deaths which were
also studied. Adequacy of health services showed that antenatal and
childbirth care was appropriate for 24% and 33.3% of pregnant
women, respectively, which corroborates the results of prevention.
These results revealed that shortcomings in obstetric and antenatal
care could be the causes of deaths in the study. Early and late
neonatal deaths have similar characteristics: 76% could be prevented
or reduced mainly by adequate newborn care (52.9%) and adequate
health care for gestational women (11.7%). When adequacy of care
was evaluated, childbirth and newborn care was adequate in 25.8%
and antenatal care was adequate in 16.1%. In conclusion, direct
relationship was found between adequacy and quality of care
rendered to pregnant women and newborns, and fetal and infant
mortality. Moreover, our findings highlight that deaths could be
prevented by an adequate obstetric and neonatal management.
Abstract: The aim of this study was to design and simulate a
particular type of Asynchronous State Machine (ASM), namely a
‘traffic light controller’ (TLC), operated at a frequency of 0.5 Hz.
The design task involved two main stages: firstly, designing a 4-bit
binary counter using J-K flip flops as the timing signal and,
subsequently, attaining the digital logic by deploying ASM design
process. The TLC was designed such that it showed a sequence of
three different colours, i.e. red, yellow and green, corresponding to
set thresholds by deploying the least number of AND, OR and NOT
gates possible. The software Multisim was deployed to design such
circuit and simulate it for circuit troubleshooting in order for it to
display the output sequence of the three different colours on the
traffic light in the correct order. A clock signal, an asynchronous 4-
bit binary counter that was designed through the use of J-K flip flops
along with an ASM were used to complete this sequence, which was
programmed to be repeated indefinitely. Eventually, the circuit was
debugged and optimized, thus displaying the correct waveforms of
the three outputs through the logic analyser. However, hazards
occurred when the frequency was increased to 10 MHz. This was
attributed to delays in the feedback being too high.