Abstract: The main idea of this work is to investigate the effect
of knitted fabrics characteristics on moisture management properties.
Wetting and transport properties of single jersey, Rib 1&1 and
English Rib fabrics made out of cotton and blended Cotton/Polyester
yarns were studied. The dynamic water sorption of fabrics was
investigated under same isothermal and terrestrial conditions at
20±2°C-65±4% by using the Moisture Management Tester (MMT)
which can be used to quantitatively measure liquid moisture transfer
in one step in a fabric in multidirections: Absorption rate, moisture
absorbing time of the fabric's inner and outer surfaces, one-way
transportation capability, the spreading/drying rate, the speed of
liquid moisture spreading on fabric's inner and outer surfaces are
measured, recorded and discussed. The results show that fabric’s
composition and knit’s structure have a significant influence on those
phenomena.
Abstract: Current transformers are an integral part of power
system because it provides a proportional safe amount of current for
protection and measurement applications. However, when the power
system experiences an abnormal situation leading to huge current
flow, then this huge current is proportionally injected to the
protection and metering circuit. Since the protection and metering
equipment’s are designed to withstand only certain amount of current
with respect to time, these high currents pose a risk to man and
equipment. Therefore, during such instances, the CT saturation
characteristics have a huge influence on the safety of both man and
equipment and on the reliability of the protection and metering
system. This paper shows the effect of burden on the Accuracy Limiting
factor/ Instrument security factor of current transformers and the
change in saturation characteristics of the CT’s. The response of the
CT to varying levels of overcurrent at different connected burden will
be captured using the data acquisition software LabVIEW. Analysis
is done on the real time data gathered using LabVIEW. Variation of
current transformer saturation characteristics with changes in burden
will be discussed.
Abstract: To decrease the grating scale thermal expansion error,
a novel method which based on multiple temperature detection is
proposed. Several temperature sensors are installed on the grating
scale and the temperatures of these sensors are recorded. The
temperatures of every point on the grating scale are calculated by
interpolating between adjacent sensors. According to the thermal
expansion principle, the grating scale thermal expansion error model
can be established by doing the integral for the variations of position
and temperature. A novel compensation method is proposed in this
paper. By applying the established error model, the grating scale
thermal expansion error is decreased by 90% compared with no
compensation. The residual positioning error of the grating scale is
less than 15μm/10m and the accuracy of the machine tool is
significant improved.
Abstract: Wire Electric Discharge Machining (WEDM) is
thermal machining process capable of machining very hard
electrically conductive material irrespective of their hardness.
WEDM is being widely used to machine micro scale parts with the
high dimensional accuracy and surface finish. The objective of this
paper is to optimize the process parameters of wire EDM to fabricate
the micro channels and to calculate the surface finish and material
removal rate of micro channels fabricated using wire EDM. The
material used is aluminum 6061 alloy. The experiments were
performed using CNC wire cut electric discharge machine. The effect
of various parameters of WEDM like pulse on time (TON) with the
levels (100, 150, 200), pulse off time (TOFF) with the levels (25, 35,
45) and current (IP) with the levels (105, 110, 115) were investigated
to study the effect on output parameter i.e. Surface Roughness and
Material Removal Rate (MRR). Each experiment was conducted
under different conditions of pulse on time, pulse off time and peak
current. For material removal rate, TON and Ip
were the most significant process parameter. MRR increases with the increase in
TON and Ip and decreases with the increase in TOFF. For surface
roughness, TON and Ip have the maximum effect and TOFF was found
out to be less effective.
Abstract: A biosphere reserve is developed to create harmony
amongst economic development, community development, and
environmental protection, through partnership between human and
nature. Giam Siak Kecil Bukit Batu Biosphere Reserve (GSKBB BR)
in Riau Province, Indonesia, is unique in that it has peat soil
dominating the area, many springs essential for human livelihood,
high biodiversity. Furthermore, it is the only biosphere reserve
covering privately managed production forest areas. In this research, we aimed at analyzing the threat of deforestation
and forest fire, and the potential of CO2 emission at GSKBB BR. We
used Landsat image, arcView software, and ERDAS IMAGINE 8.5
Software to conduct spatial analysis of land cover and land use
changes, calculated CO2 emission based on emission potential from
each land cover and land use type, and exercised simple linear
regression to demonstrate the relation between CO2 emission
potential and deforestation. The result showed that, beside in the buffer zone and transition
area, deforestation also occurred in the core area. Spatial analysis of
land cover and land use changes from years 2010, 2012, and 2014
revealed that there were changes of land cover and land use from
natural forest and industrial plantation forest to other land use types,
such as garden, mixed garden, settlement, paddy fields, burnt areas,
and dry agricultural land. Deforestation in core area, particularly at
the Giam Siak Kecil Wildlife Reserve and Bukit Batu Wildlife
Reserve, occurred in the form of changes from natural forest in to
garden, mixed garden, shrubs, swamp shrubs, dry agricultural land,
open area, and burnt area. In the buffer zone and transition area,
changes also happened, what once swamp forest changed into garden,
mixed garden, open area, shrubs, swamp shrubs, and dry agricultural
land. Spatial analysis on land cover and land use changes indicated
that deforestation rate in the biosphere reserve from 2010 to 2014 had
reached 16 119 ha/year. Beside deforestation, threat toward the
biosphere reserve area also came from forest fire. The occurrence of forest fire in 2014 had burned 101 723 ha of the
area, in which 9 355 ha of core area, and 92 368 ha of buffer zone
and transition area. Deforestation and forest fire had increased CO2
emission as much as 24 903 855 ton/year.
Abstract: As a basic physiology need, threat to sufficient food
production is threat to human survival. Food security has been an
issue that has gained global concern. This paper looks at the food
security in Nigeria by assessing the availability of food and
accessibility of the available food. The paper employed multiple
linear regression technique and graphic trends of growth rates of
relevant variables to show the situation of food security in Nigeria.
Results of the tests revealed that population growth rate was higher
than the growth rate of food availability in Nigeria for the earlier
period of the study. Commercial bank credit to agricultural sector,
foreign exchange utilization for food and the Agricultural Credit
Guarantee Scheme Fund (ACGSF) contributed significantly to food
availability in Nigeria. Food prices grew at a faster rate than the
average income level, making it difficult to access sufficient food. It
implies that prior to the year 2012; there was insufficient food to feed
the Nigerian populace. However, continued credit to the food and
agricultural sector will ensure sustained and sufficient production of
food in Nigeria. Microfinance banks should make sufficient credit
available to smallholder farmer. Government should further control
and subsidize the rising price of food to make it more accessible by
the people.
Abstract: This paper discusses the question whether a person
diagnosed with dyslexia will necessarily have difficulty in reading
musical notes. The author specifies the characteristics of alphabet
reading in comparison to musical notation reading, and concludes
that there should be no contra-indication for teaching standard music
reading to children with dyslexia if an appropriate process is offered.
This conclusion is based on a long term case study and relies on two
main characteristics of music reading: (1) musical notation system is
a systematic, logical, relative set of symbols written on a staff; and
(2) music reading learning connected with playing a musical
instrument is a multi-sensory activity that combines sight, hearing,
touch, and movement. The paper describes music reading teaching
procedures, using soprano recorders, and provides unique teaching
methods that have been found to be effective for students who were
diagnosed with dyslexia. It provides theoretical explanations in
addition to guidelines for music education practices.
Abstract: This paper presents the interface ConductHome which
controls home automation systems with a Leap Motion using
“invariant gesture protocols”. This interface is meant to simplify the
interaction of the user with its environment. A hardware part allows
the Leap Motion to be carried around the house. A software part
interacts with the home automation box and displays the useful
information for the user. An objective of this work is the
development of a natural/invariant/simple gesture control interface to
help elder people/people with disabilities.
Abstract: This paper considers the design of Dual Proportional-
Integral (DPI) Load Frequency Control (LFC), using gravitational
search algorithm (GSA). The design is carried out for nonlinear
hydrothermal power system where generation rate constraint (GRC)
and governor dead band are considered. Furthermore, time delays
imposed by governor-turbine, thermodynamic process, and
communication channels are investigated. GSA is utilized to search
for optimal controller parameters by minimizing a time-domain based
objective function. GSA-based DPI has been compared to Ziegler-
Nichols based PI, and Genetic Algorithm (GA) based PI controllers
in order to demonstrate the superior efficiency of the proposed
design. Simulation results are carried for a wide range of operating
conditions and system parameters variations.
Abstract: The moisture content of densified biomass is a
limiting parameter influencing the quality of this solid biofuel. It
influences its calorific value, density, mechanical strength and
dimensional stability as well as affecting its production process. This
paper deals with experimental research into the effect of moisture
content of the densified material on the final quality of biofuel in the
form of logs (briquettes or pellets). Experiments based on the singleaxis
densification of the spruce sawdust were carried out with a
hydraulic piston press (piston and die), where the densified logs were
produced at room temperature. The effect of moisture content on the
qualitative properties of the logs, including density, change of
moisture, expansion and physical changes, and compressive and
impact resistance were studied. The results show the moisture ranges
required for producing good-quality logs. The experiments were
evaluated and the moisture content of the tested material was
optimized to achieve the optimum value for the best quality of the
solid biofuel. The dense logs also have high-energy content per unit
volume. The research results could be used to develop and optimize
industrial technologies and machinery for biomass densification to
achieve high quality solid biofuel.
Abstract: Healthcare safety has been perceived important. It is
essential to prevent troubles in healthcare processes for healthcare
safety. Trouble prevention is based on trouble prediction using
accumulated knowledge on processes, troubles, and countermeasures.
However, information on troubles has not been accumulated in
hospitals in the appropriate structure, and it has not been utilized
effectively to prevent troubles. In the previous study, however a
detailed knowledge acquisition process for trouble prediction was
proposed, the knowledgebase for countermeasures was not involved.
In this paper, we aim to propose the structure of the knowledgebase for
countermeasures, in the knowledge acquisition process for trouble
prediction in healthcare process. We first design the structure of
countermeasures and propose the knowledge representation form on
countermeasures. Then, we evaluate the validity of the proposal, by
applying it into an actual hospital.
Abstract: This paper seeks to assess the implications of bank
consolidation on lending, which largely determine the survival and
performance of small and medium scale enterprises and in turn the
development of the Nigerian economy. Ordinary least square
technique, correlation matrix test and Granger –causality test were
employed to measure the extent to which lending to small and
medium scale enterprises were influenced. The result showed that
bank deposit (BD) impacted on lending to small and medium scale
enterprises. Commercial and merchant bank lending rate had
statistically insignificant effect on the dependent variable. There is a
shift of focus by commercial banks from small and medium scale
enterprises (small customers) to major investors (big customers).
While micro finance banks work hard at providing funds to small and
medium scale entrepreneurs, their capacity to meet the needs of these
entrepreneurs is constrained. The capital and deposits of micro
finance bank should be boosted in order to effectively support small
and medium scale enterprises through loans.
Abstract: Drought is one of the most serious problems posing a
grave threat to cereals production including maize. Maize
improvement in drought-stress tolerance poses a great challenge as
the global need for food and bio-energy increases. Thus, the current
study was planned to explore the variations and determine the
performance of target traits of maize hybrids at grain growth stage
under drought conditions during 2014 under Adana, Mediterranean
climate conditions, Turkey. Maize hybrids (Sancia, Indaco,
71May69, Aaccel, Calgary, 70May82, 72May80) were evaluated
under (irrigated and water stress). Results revealed that, grain yield
and yield traits had a negative effects because of water stress
conditions compared with the normal irrigation. As well as, based on
the result under normal irrigation, the maximum biological yield and
harvest index were recorded. According to the differences among
hybrids were found that, significant differences were observed among
hybrids with respect to yield and yield traits under current research. Based on the results, grain weight had more effect on grain yield
than grain number during grain filling growth stage under water
stress conditions. In this concern, according to low drought
susceptibility index (less grain yield losses), the hybrid (Indaco) was
more stable in grain number and grain weight. Consequently, it may
be concluded that this hybrid would be recommended for use in the
future breeding programs for production of drought tolerant hybrids.
Abstract: Oxygen Reduction Reaction (ORR) performance of
iron and nitrogen co-doped porous carbon nanoparticles (Fe-NPC)
with various physical and (electro) chemical properties have been
investigated. Fe-NPC nanoparticles are synthesized via a facile
soft-templating procedure by using Iron (III) chloride hexa-hydrate as
iron precursor and aminophenol-formaldehyde resin as both carbon
and nitrogen precursor. Fe-NPC nanoparticles shows high surface area
(443.83 m2g-1), high pore volume (0.52 m3g-1), narrow mesopore size
distribution (ca. 3.8 nm), high conductivity (IG/ID=1.04), high kinetic
limiting current (11.71 mAcm-2) and more positive onset potential
(-0.106 V) compared to metal-free NPC nanoparticles (-0.295V)
which make it high efficient ORR metal-free catalysts in alkaline
solution. This study may pave the way of feasibly designing iron and
nitrogen containing carbon materials (Fe-N-C) for highly efficient
oxygen reduction electro-catalysis.
Abstract: Damaturu is the capital of Yobe State in northeastern
Nigeria where civic amenities and facilities are not adequate even
after 24 years of its existence. The volatile security and political
situations are most significant causes for the same. The basic facility
for the citizens in terms of drinking water and electricity are not
available. For the drinking water, they have to rely on personal
boreholes or the filtered borehole waters available in packaged
sachets in market. The present study is concerned with environmental
impact of indiscriminate disposal of drinking synthetic polythene
water sachets in Damaturu. The sachet water is popularly called as
“pure water”, but its purity is questionable. Increased production and
consumption of sachet water has led to indiscriminate dumping and
disposal of empty sachets leading to serious environmental threat.
The evidence of this is seen for sachets littering the streets and the
drainages blocked by ‘blocks’ of water sachet waste. Sachet water
gained much popularity in Nigeria because the product is convenient
for use, affordable and economically viable. The present study aims
to find out the solution to this environmental problem. The fieldbased
study has found some significant factors that cause
environmental and socio economic effect due to this. Some
recommendations have been made based on research findings
regarding sustainable waste management, recycling and re-use of the
non-biodegradable products in society.
Abstract: Erosion and abrasion are wear mechanisms reducing
the lifetime of machine elements like valves, pump and pipe systems.
Both wear mechanisms are acting at the same time, causing a
“Synergy” effect, which leads to a rapid damage of the surface.
Different parameters are effective on erosive abrasive wear rate. In
this study effect of particle impact angle on wear rate and wear
mechanism of ductile and brittle materials was investigated. A new
slurry pot was designed for experimental investigation. As abrasive
particle, silica sand was used. Particle size was ranking between 200-
500 μm. All tests were carried out in a sand-water mixture of 20%
concentration for four hours. Impact velocities of the particles were
4.76 m/s. As ductile material steel St 37 with Vickers Hardness
Number (VHN) of 245 and quenched St 37 with 510 VHN was used
as brittle material. After wear tests, morphology of the eroded
surfaces were investigated for better understanding of the wear
mechanisms acting at different impact angles by using Scanning
Electron Microscope. The results indicated that wear rate of ductile
material was higher than brittle material. Maximum wear rate was
observed by ductile material at a particle impact angle of 300 and
decreased further by an increase in attack angle. Maximum wear rate
by brittle materials was by impact angle of 450 and decreased further
up to 900. Ploughing was the dominant wear mechanism by ductile
material. Microcracks on the surface were detected by ductile
materials, which are nucleation centers for crater formation. Number
of craters decreased and depth of craters increased by ductile
materials by attack angle higher than 300. Deformation wear
mechanism was observed by brittle materials. Number and depth of
pits decreased by brittle materials by impact angles higher than 450.
At the end it is concluded that wear rate could not be directly related
to impact angle of particles due to the different reaction of ductile and
brittle materials.
Abstract: Nitrification is essential to biological processes
designed to remove ammonia and/or total nitrogen. It removes excess
nitrogenous compound in wastewater which could be very toxic to
the aquatic fauna or cause serious imbalance of such aquatic
ecosystem. Efficient nitrification is linked to an in-depth knowledge
of the structure and dynamics of the nitrifying community structure
within the wastewater treatment systems. In this study, molecular
technique was employed for characterizing the microbial structure of
activated sludge [ammonia oxidizing bacteria (AOB) and nitrite
oxidizing bacteria (NOB)] in a municipal wastewater treatment with
intention of linking it to the plant efficiency. PCR based phylogenetic
analysis was also carried out. The average operating and
environmental parameters as well as specific nitrification rate of plant
was investigated during the study. During the investigation the average temperature was 23±1.5oC.
Other operational parameters such as mixed liquor suspended solids
and chemical oxygen demand inversely correlated with ammonia
removal. The dissolved oxygen level in the plant was constantly
lower than the optimum (between 0.24 and 1.267 mg/l) during this
study. The plant was treating wastewater with influent ammonia
concentration of 31.69 and 24.47 mg/L. The influent flow rates
(ML/Day) was 96.81 during period. The dominant nitrifiers include:
Nitrosomonas spp. Nitrobacter spp. and Nitrospira spp. The AOB
had correlation with nitrification efficiency and temperature. This
study shows that the specific ammonia oxidizing rate and the specific
nitrate formation rates can serve as good indicator of the plant overall
nitrification performance.
Abstract: This paper addresses minimizing the makespan of the
distributed permutation flow shop scheduling problem. In this
problem, there are several parallel identical factories or flowshops
each with series of similar machines. Each job should be allocated to
one of the factories and all of the operations of the jobs should be
performed in the allocated factory. This problem has recently gained
attention and due to NP-Hard nature of the problem, metaheuristic
algorithms have been proposed to tackle it. Majority of the proposed
algorithms require large computational time which is the main
drawback. In this study, a general variable neighborhood search
algorithm (GVNS) is proposed where several time-saving schemes
have been incorporated into it. Also, the GVNS uses the sophisticated
method to change the shaking procedure or perturbation depending
on the progress of the incumbent solution to prevent stagnation of the
search. The performance of the proposed algorithm is compared to
the state-of-the-art algorithms based on standard benchmark
instances.
Abstract: Polymeric micro-cantilevers (Cs) are rapidly
becoming popular for MEMS applications such as chemo- and biosensing
as well as purely electromechanical applications such as
microrelays. Polymer materials present suitable physical and
chemical properties combined with low-cost mass production. Hence,
micro-cantilevers made of polymers indicate much more
biocompatibility and adaptability of rapid prototyping along with
mechanical properties. This research studies the effects of three
process and one size factors on the filling behaviour in micro cavity,
and the role of each in the replication of micro parts using different
polymer materials i.e. polypropylene (PP) SABIC 56M10 and
acrylonitrile butadiene styrene (ABS) Magnum 8434 . In particular,
the following factors are considered: barrel temperature, mould
temperature, injection speed and the thickness of micro features. The
study revealed that the barrel temperature and the injection speed are
the key factors affecting the flow length of micro features replicated
in PP and ABS. For both materials, an increase of feature sizes
improves the melt flow. However, the melt fill of micro features does
not increase linearly with the increase of their thickness.
Abstract: Sweden has succeeded to maintain a high level of
growth and development and has managed to sustain highly ranked
position among the world’s developed countries. In this regard,
Swedish universities are playing a vital role in supporting innovation
and entrepreneurship at all levels and developing Swedish knowledge
economy. This paper is aiming to draw on the experiences of two leading
Swedish universities, addressing their transformation approach to
create entrepreneurial universities and fulfilling their objectives in the
era of knowledge economy. The objectives of the paper include: 1) Introducing the Swedish
higher education and its characteristics. 2) Examining the
infrastructure elements for innovation and Entrepreneurship at two of
the Swedish entrepreneurial universities. 3) Addressing the key
aspects of support systems in the initiatives of both Chalmers and
Gothenburg universities to support innovation and advance
entrepreneurial practices. The paper will contribute to two discourses: 1) Examining the
relationship between support systems for innovation and
entrepreneurship and the Universities’ policies and practices. 2)
Lessons for University leaders to assist the development and
implementation of effective innovation and entrepreneurship policies
and practices.