Abstract: By GEO5 FEM program with four rockfill slope
modeling and stability analysis was performed for S1, S2, S3 and
S4 slopes where landslides of the shalefills were limited. Effective
angle of internal friction (φ'°) 17°-22.5°, the effective cohesion (c')
from 0.5 to 1.8 kPa, saturated unit weight 1.78-2.43 g/cm3, natural
unit weight 1.9-2.35 g/cm3, dry unit weight 1.97-2.40 g/cm3, the
permeability coefficient of 1x10-4 - 6.5x10-4 cm/s. In cross-sections
of the slope, GEO 5 FEM program possible critical surface tension
was examined. Rockfill dump design was made to prevent sliding
slopes. Bulk material designated geotechnical properties using also
GEO5 programs FEM and stability program via a safety factor
determined and calculated according to the values S3 and S4 No.
slopes are stable S1 and S2 No. slopes were close to stable state
that has been found to be risk. GEO5 programs with limestone rock
fill dump through FEM program was found to exhibit stability.
Abstract: This research was made during the 2015 growing
periods in the trial filed of "Research Station for Department of Field
Crops, Agricultural Faculty, Selcuk University" according to
“Randomized Blocks Design” with 3 replications. Research material
was the following pea lines; PS16, PS18, PS21, PS23, PS24, PS25,
PS36, PS47, PS49, PS51, PS54, PS58, PS67, PS69, PS71, PS73,
PS83, PS84, PS87 and PSKY and three cultivars and other 2
commercial varieties named as Bolero, Rondo and Ultrello. Some
agronomical characteristics such as plant height (cm) number of pod
per plant number of seed per pod number of seed per plant 100 seed
weight (g) and seed yield (kg ha-1) were determined. The highest seed
yield was obtained 2727.0 kg ha-1 in the PS71 line and the lowest
value was obtained 1238.0 kg ha-1 in the commercial variety of
Bolero. Results of the research implicated that the new developed
lines were superior compared with the control (commercial) varieties
by means of most of the characteristics. Nevertheless, similar
researches should be continued in different locations and years.
Abstract: This research was planned in order to study the effect
of drought stress and different levels of Superabsorbent and their
effect on grain yield, biologic yield and harvest index. In this study, 3
different depths of irrigation were considered as the main treatment
I1, I2, I3 as 100, 75 and 50 percent of water requirement of plants
respectively and different levels of Superabsorbent were used as
secondary treatment (S0, S1, S2 and S3, equal to 0 (control), 15, 30
and 45 gr/m2 respectively). According to the results, independent
effects of irrigation and Superabsorbent treatments at 1% level on
biologic and grain yield of corn were significant. In addition,
independent effect of irrigation treatments at 5% level on harvest
index was significant. But independent effect of Superabsorbent
treatments on harvest index was not significant.
Abstract: Optic disk segmentation plays a key role in the mass
screening of individuals with diabetic retinopathy and glaucoma
ailments. An efficient hardware-based algorithm for optic disk
localization and segmentation would aid for developing an automated
retinal image analysis system for real time applications. Herein,
TMS320C6416DSK DSP board pixel intensity based fractal analysis
algorithm for an automatic localization and segmentation of the optic
disk is reported. The experiment has been performed on color and
fluorescent angiography retinal fundus images. Initially, the images
were pre-processed to reduce the noise and enhance the quality. The
retinal vascular tree of the image was then extracted using canny
edge detection technique. Finally, a pixel intensity based fractal
analysis is performed to segment the optic disk by tracing the origin
of the vascular tree. The proposed method is examined on three
publicly available data sets of the retinal image and also with the data
set obtained from an eye clinic. The average accuracy achieved is
96.2%. To the best of the knowledge, this is the first work reporting
the use of TMS320C6416DSK DSP board and pixel intensity based
fractal analysis algorithm for an automatic localization and
segmentation of the optic disk. This will pave the way for developing
devices for detection of retinal diseases in the future.
Abstract: Any signal transmitted over a channel is corrupted by noise and interference. A host of channel coding techniques has been proposed to alleviate the effect of such noise and interference. Among these Turbo codes are recommended, because of increased capacity at higher transmission rates and superior performance over convolutional codes. The multimedia elements which are associated with ample amount of data are best protected by Turbo codes. Turbo decoder employs Maximum A-posteriori Probability (MAP) and Soft Output Viterbi Decoding (SOVA) algorithms. Conventional Turbo coded systems employ Equal Error Protection (EEP) in which the protection of all the data in an information message is uniform. Some applications involve Unequal Error Protection (UEP) in which the level of protection is higher for important information bits than that of other bits. In this work, enhancement to the traditional Log MAP decoding algorithm is being done by using optimized scaling factors for both the decoders. The error correcting performance in presence of UEP in Additive White Gaussian Noise channel (AWGN) and Rayleigh fading are analyzed for the transmission of image with Discrete Cosine Transform (DCT) as source coding technique. This paper compares the performance of log MAP, Modified log MAP (MlogMAP) and Enhanced log MAP (ElogMAP) algorithms used for image transmission. The MlogMAP algorithm is found to be best for lower Eb/N0 values but for higher Eb/N0 ElogMAP performs better with optimized scaling factors. The performance comparison of AWGN with fading channel indicates the robustness of the proposed algorithm. According to the performance of three different message classes, class3 would be more protected than other two classes. From the performance analysis, it is observed that ElogMAP algorithm with UEP is best for transmission of an image compared to Log MAP and MlogMAP decoding algorithms.
Abstract: Fast speed drives for Permanent Magnet Synchronous
Motor (PMSM) is a crucial performance for the electric traction
systems. In this paper, PMSM is derived with a Model-based
Predictive Control (MPC) technique. Fast speed tracking is achieved
through optimization of the DC source utilization using MPC. The
technique is based on predicting the optimum voltage vector applied
to the driver. Control technique is investigated by comparing to the
cascaded PI control based on Space Vector Pulse Width Modulation
(SVPWM). MPC and SVPWM-based FOC are implemented with the
TMS320F2812 DSP and its power driver circuits. The designed MPC
for a PMSM drive is experimentally validated on a laboratory test
bench. The performances are compared with those obtained by a
conventional PI-based system in order to highlight the improvements,
especially regarding speed tracking response.
Abstract: Super steel materials play a vital role in the
construction and fabrication of structural, piping and pipeline
components. In assuring the integrity of onshore and offshore
operating systems, they enable life cycle costs to be minimized. In
this context, Duplex stainless steel (DSS) material related welding on
constructions and fabrications plays a significant role in maintaining
and assuring integrity at an optimal expenditure over the life cycle of
production and process systems as well as associated structures. In
DSS welding, factors such as gap geometry, shielding gas supply
rate, welding current, and type of the welding process are vital to the
final joint performance. Hence, an experimental investigation has
been performed using an engineering robust design approach
(ERDA) to investigate the optimal settings that generate optimal
super DSS (i.e. UNS S32750) joint performance. This manuscript
illustrates the mathematical approach and experimental design,
optimal parameter settings and results of the verification experiment.
Abstract: Enzyme activity was evaluated in the intestine of
juvenile dourado (Salminus brasiliensis) fed with diets containing 0,
10 or 20% of lyophilized bovine colostrum (LBC) inclusion for either
30 or 60 days. The intestinal enzymes acid and alkaline phosphatase
(ACP and ALP, respectively), non-specific esterase (NSE), lipase
(LIP), dipeptidyl aminopeptidase IV (DAP IV) and leucine
aminopeptidase (LAP) were studied using histochemistry in four
intestinal segments (S1, S2, S3 and posterior intestine). Weak
proteolitic activity was observed in all intestinal segments for DAP
IV and LAP. The activity of NSE and LIP was also weak in all
intestines, except for the moderate activity of NSE in the S2 of 20%
LBC group after 30 days and in the S1 of 0% LBC group after 60
days. The ACP was detected only in the S2 and S3 of the 10% LBC
group after 30 days. Moderate and strong staining was observed in
the first three intestinal segments for ALP and weak activity in the
posterior intestine. The activity of DAP IV, LAP and ALP were also
present in the cytoplasm of the enterocytes. In the present results,
bovine colostrum feeding did not cause alterations in activity of
intestinal enzymes.
Abstract: Osteoporosis is a common multifactorial disease with
a strong genetic component characterized by reduced bone mass and
increased risk of fractures. Genetic factors play an important role in
the pathogenesis of osteoporosis. The aim of our study was to
identify the genotype and allele distribution of T245G polymorphism
in OPG gene in Slovak postmenopausal women. A total of 200
unrelated Slovak postmenopausal women with diagnosed
osteoporosis and 200 normal controls were genotyped for T245G
(rs3134069) polymorphism of OPG gene. Genotyping was performed
using the Custom Taqman®SNP Genotyping assays. Genotypes and
alleles frequencies showed no significant differences (p=0.5551;
p=0.6022). The results of the present study confirm the importance of
T245G polymorphism in OPG gene in the pathogenesis of
osteoporosis.
Abstract: Complex sensitivity analysis of stresses in a concrete slab of the real type of rigid pavement made from recycled materials is performed. The computational model of the pavement is designed as a spatial (3D) model, is based on a nonlinear variant of the finite element method that respects the structural nonlinearity, enables to model different arrangements of joints, and the entire model can be loaded by the thermal load. Interaction of adjacent slabs in joints and contact of the slab and the subsequent layer are modeled with the help of special contact elements. Four concrete slabs separated by transverse and longitudinal joints and the additional structural layers and soil to the depth of about 3m are modeled. The thickness of individual layers, physical and mechanical properties of materials, characteristics of joints, and the temperature of the upper and lower surface of slabs are supposed to be random variables. The modern simulation technique Updated Latin Hypercube Sampling with 20 simulations is used. For sensitivity analysis the sensitivity coefficient based on the Spearman rank correlation coefficient is utilized. As a result, the estimates of influence of random variability of individual input variables on the random variability of principal stresses s1 and s3 in 53 points on the upper and lower surface of the concrete slabs are obtained.
Abstract: A process of conversion of flour from three varieties of cassava, namely Odongbo, ofege and TMS30752 to ethanol using α-amylase locally sourced from germinated unhusked paddy rice and yeast isolated from palm wine was developed. It involves the germination of paddy rice for a period of 15days to produce α-amylase for starch hydrolysis and isolation of yeast from palm wine for fermentation. The results showed that optimum amylase yield of “ofada” rice paddy was at 6th day germination which was 576.9ml/g. Ethanol yield for TMS30572 (440.3%) was significantly higher than “Odongbo” (160.2%) and “Ofege’’ (115.1%), Sugar conversion efficiency were 311.0%v/v, 268.2%v/v and 186.84%v/v for TMS30572, “Odongbo” and “Ofege” respectively. The ethanol boiling points were 78oC, 76oC and 80oC for TMS30572, “Odongbo” and “Ofege” respectively. This study showed that cassava varieties affects quality of ethanol produced and germination of “ofada” rice for 6 days ensures optimum production of crude amylase enzyme.
Abstract: The objectives of this study were to isolate LAB from various sources, dietary supplement, Thai traditional fermented food, and freshwater fish and to characterize their potential as probiotic cultures. Out of 1,558 isolates, 730 were identified as LAB based on isolation on MRS agar supplemented with a bromocresol purple indicator&CaCO3 and Gram-positive, catalase- and oxidase-negative characteristics. Eight isolates showed the potential probiotic properties including tolerance to acid, bile salt & heat, proteolytic, amylolytic & lipolytic activities and oxalate-degrading capability. They all showed the antimicrobial activity against some Gram-negative and Gram-positive pathogenic bacteria. Based on 16S rDNA sequence analysis, they were identified as Enterococcus faecalis BT2 & MG30, Leconostoc mesenteroides SW64 and Pediococcus pentosaceous BD33, CF32, NP6, PS34 & SW5. The health beneficial effects and food safety will be further investigated and developed as a probiotic or protective culture used in Nile tilapia belly flap meat fermentation.
Abstract: This paper presents advances in pulse width modulation techniques which refers to a method of carrying information on train of pulses and the information be encoded in the width of pulses. Pulse Width Modulation is used to control the inverter output voltage. This is done by exercising the control within the inverter itself by adjusting the ON and OFF periods of inverter. By fixing the DC input voltage we get AC output voltage. In variable speed AC motors the AC output voltage from a constant DC voltage is obtained by using inverter. Recent developments in power electronics and semiconductor technology have lead improvements in power electronic systems. Hence, different circuit configurations namely multilevel inverters have became popular and considerable interest by researcher are given on them. A fast space-vector pulse width modulation (SVPWM) method for five-level inverter is also discussed. In this method, the space vector diagram of the five-level inverter is decomposed into six space vector diagrams of three-level inverters. In turn, each of these six space vector diagrams of three-level inverter is decomposed into six space vector diagrams of two-level inverters. After decomposition, all the remaining necessary procedures for the three-level SVPWM are done like conventional two-level inverter. The proposed method reduces the algorithm complexity and the execution time. It can be applied to the multilevel inverters above the five-level also. The experimental setup for three-level diode-clamped inverter is developed using TMS320LF2407 DSP controller and the experimental results are analyzed.
Abstract: Altered drug binding may be an important factor in isoniazid (INH) resistance, rather than major changes in the enzyme’s activity as a catalase or peroxidase (KatG). The identification of structural or functional defects in the mutant KatGs responsible for INH resistance remains as an area to be explored. In this connection, the differences in the binding affinity between wild-type (WT) and mutants of KatG were investigated, through the generation of three mutants of KatG, Ser315Thr [S315T], Ser315Asn [S315N], Ser315Arg [S315R] and a WT [S315]) with the help of software-MODELLER. The mutants were docked with INH using the software-GOLD. The affinity is lower for WT than mutant, suggesting the tight binding of INH with the mutant protein compared to WT type. These models provide the in silico evidence for the binding interaction of KatG with INH and implicate the basis for rationalization of INH resistance in naturally occurring KatG mutant strains of Mycobacterium tuberculosis.
Abstract: Osteoporosis is a complex health disease characterized by low bone mineral density, which is determined by an interaction of genetics with metabolic and environmental factors. Current research in genetics of osteoporosis is focused on identification of responsible genes and polymorphisms. TNFRSF11B gene plays a key role in bone remodeling. The aim of this study was to investigate the genotype and allele distribution of A163G (rs3102735) osteoprotegerin gene promoter and G1181C (rs2073618) osteoprotegerin first exon polymorphisms in the group of 180 unrelated postmenopausal women with diagnosed osteoporosis and 180 normal controls. Genomic DNA was isolated from peripheral blood leukocytes using standard methodology. Genotyping for presence of different polymorphisms was performed using the Custom Taqman®SNP Genotyping assays. Hardy-Weinberg equilibrium was tested for each SNP in the groups of participants using the chi-square (χ2) test. The distribution of investigated genotypes in the group of patients with osteoporosis were as follows: AA (66.7%), AG (32.2%), GG (1.1%) for A163G polymorphism; GG (19.4%), CG (44.4%), CC (36.1%) for G1181C polymorphism. The distribution of genotypes in normal controls were follows: AA (71.1%), AG (26.1%), GG (2.8%) for A163G polymorphism; GG (22.2%), CG (48.9%), CC (28.9%) for G1181C polymorphism. In A163G polymorphism the variant G allele was more common among patients with osteoporosis: 17.2% versus 15.8% in normal controls. Also, in G1181C polymorphism the phenomenon of more frequent occurrence of C allele in the group of patients with osteoporosis was observed (58.3% versus 53.3%). Genotype and allele distributions showed no significant differences (A163G: χ2=0.270, p=0.605; χ2=0.250, p=0.616; G1181C: χ2= 1.730, p=0.188; χ2=1.820, p=0.177). Our results represents an initial study, further studies of more numerous file and associations studies will be carried out. Knowing the distribution of genotypes is important for assessing the impact of these polymorphisms on various parameters associated with osteoporosis. Screening for identification of “at-risk” women likely to develop osteoporosis and initiating subsequent early intervention appears to be most effective strategy to substantially reduce the risks of osteoporosis.
Abstract: Abrasive Water Jet Machining is an unconventional machining process well known for machining hard to cut materials. The primary research focus on the process was for through cutting and a very limited literature is available on pocket milling using AWJM. The present work is an attempt to use this process for milling applications considering a set of various process parameters. Four different input parameters, which were considered by researchers for part separation, are selected for the above application, i.e., abrasive size, flow rate, standoff distance and traverse speed. Pockets of definite size are machined to investigate surface roughness, material removal rate and pocket depth. Based on the data available through experiments on SS304 material, it is observed that higher traverse speeds gives a better finish because of reduction in the particle energy density and lower depth is also observed. Increase in the standoff distance and abrasive flow rate reduces the rate of material removal as the jet loses its focus and occurrence of collisions within the particles. ANOVA for individual output parameter has been studied to know the significant process parameters.
Abstract: Simultaneous measurements of the curves for wear versus distance, wear rate versus distance, and coefficient of friction versus distance were performed in situ to distinguish the transition from severe running-in wear to mild wear. The effects of the initial surface roughness on the severe running-in wear volume were investigated. Disk-on-plate friction and wear tests were carried out with SUS304 austenitic stainless steel in contact with itself under repeated dry sliding conditions at room temperature. The wear volume was dependent on the initial surface roughness. The wear volume when the initial surfaces on the plate and disk had dissimilar roughness was lower than that when these surfaces had similar roughness. For the dissimilar roughness, the wear volume decreased with decreasing initial surface roughness and reached a minimum; it stayed nearly constant as the roughness was less than the mean size of the oxide particles.
Abstract: This paper presents an effective technique for harmonic current mitigation using an adaptive notch filter (ANF) to estimate current harmonics. The proposed filter consists of multiple units of ANF connected in parallel structure; each unit is governed by two ordinary differential equations. The frequency estimation is carried out based on the output of these units. The simulation and experimental results show the ability of the proposed tracking scheme to accurately estimate harmonics. The proposed filter was implemented digitally in TMS320F2808 and used in the control of hybrid active power filter (HAPF). The theoretical expectations are verified and demonstrated experimentally.
Abstract: Ants are fascinating creatures that demonstrate the
ability to find food and bring it back to their nest. Their ability as a
colony, to find paths to food sources has inspired the development of
algorithms known as Ant Colony Systems (ACS). The principle of
cooperation forms the backbone of such algorithms, commonly used
to find solutions to problems such as the Traveling Salesman
Problem (TSP). Ants communicate to each other through chemical
substances called pheromones. Modeling individual ants- ability to
manipulate this substance can help an ACS find the best solution.
This paper introduces a Dynamic Ant Colony System with threelevel
updates (DACS3) that enhance an existing ACS. Experiments
were conducted to observe single ant behavior in a colony of
Malaysian House Red Ants. Such behavior was incorporated into the
DACS3 algorithm. We benchmark the performance of DACS3 versus
DACS on TSP instances ranging from 14 to 100 cities. The result
shows that the DACS3 algorithm can achieve shorter distance in
most cases and also performs considerably faster than DACS.
Abstract: SAD (Sum of Absolute Difference) algorithm is
heavily used in motion estimation which is computationally highly
demanding process in motion picture encoding. To enhance the
performance of motion picture encoding on a VLIW processor, an
efficient implementation of SAD algorithm on the VLIW processor is
essential. SAD algorithm is programmed as a nested loop with a
conditional branch. In VLIW processors, loop is usually optimized by
software pipelining, but researches on optimal scheduling of software
pipelining for nested loops, especially nested loops with conditional
branches are rare. In this paper, we propose an optimal scheduling and
implementation of SAD algorithm with conditional branch on a VLIW
DSP processor. The proposed optimal scheduling first transforms the
nested loop with conditional branch into a single loop with conditional
branch with consideration of full utilization of ILP capability of the
VLIW processor and realization of earlier escape from the loop. Next,
the proposed optimal scheduling applies a modulo scheduling
technique developed for single loop. Based on this optimal scheduling
strategy, optimal implementation of SAD algorithm on TMS320C67x,
a VLIW DSP is presented. Through experiments on TMS320C6713
DSK, it is shown that H.263 encoder with the proposed SAD
implementation performs better than other H.263 encoder with other
SAD implementations, and that the code size of the optimal SAD
implementation is small enough to be appropriate for embedded
environments.